共查询到20条相似文献，搜索用时 281 毫秒
1.
高烈度地震区重力式挡土墙由于地基承载力不足导致墙身失稳是一种较常见震害类型。基于拟静力法原理,利用极限分析上限定理对地震作用下挡土墙地基极限承载力进行求解,通过典型算例分析了极限承载力随地震动峰值加速度的变化关系与机理,讨论了地基土强度参数对其变化趋势的影响,提出了同时考虑设防烈度和地基土性的挡土墙地基抗震容许承载力修正方法及相应修正系数取值建议。结果表明:设防烈度在9度及以内时,随着地震动峰值加速度增加,挡土墙地基极限承载力近似呈线性下降,下降速率与地基土黏聚力呈负相关性,而受内摩擦角的影响不显著;地震作用加剧挡土墙基底荷载倾斜与偏心导致地基破坏区缩减是造成极限承载力下降的主要原因;设防烈度大于7度时,挡土墙地基抗震容许承载力较天然工况下有所降低,8度和9度设防烈度对应的修正系数约为0.9和0.7。 相似文献
2.
Although seismic isolation rubber bearings in bridges and buildings have proven to be a very effective passive method for reducing earthquake‐induced forces, a detailed mechanical modeling of the rubber that is used in bearings under large strains has not been established. Therefore, a 3D model of failure behavior and the design criteria for the safety evaluation of seismic isolation bearings have not yet been developed. This paper presents: (1) correlation‐based template‐matching algorithms to measure large strain fields of continua; (2) a failure criterion for rubber; and (3) the design criteria for the safety evaluation of laminated algorithms, data‐validation algorithms were developed and implemented to eliminate possible unrealistic displacement vectors present in the measured displacement field. The algorithms were successfully employed in the strain field measurement of LRB and rubber materials that are subjected to failure. The measured local strains for rubber material at failure were used to develop a failure criterion for rubber. The validity of the proposed criterion was evaluated by applying it to the LRB; the criterion was introduced into a 3D finite element model of LRB, compared with the experimental results of bearings failure, and verified. Finally, design criteria are proposed for LRB for the safety evaluation. Copyright © 2003 John Wiley & Sons, Ltd. 相似文献
3.
Load and resistance factor design (LRFD) approach for the design of reinforced soil walls is presented to produce designs with consistent and uniform levels of risk for the whole range of design applications. The evaluation of load and resistance factors for the reinforced soil walls based on reliability theory is presented. A first order reliability method (FORM) is used to determine appropriate ranges for the values of the load and resistance factors. Using pseudo-static limit equilibrium method, analysis is conducted to evaluate the external stability of reinforced soil walls subjected to earthquake loading. The potential failure mechanisms considered in the analysis are sliding failure, eccentricity failure of resultant force (or overturning failure) and bearing capacity failure. The proposed procedure includes the variability associated with reinforced backfill, retained backfill, foundation soil, horizontal seismic acceleration and surcharge load acting on the wall. Partial factors needed to maintain the stability against three modes of failure by targeting component reliability index of 3.0 are obtained for various values of coefficients of variation (COV) of friction angle of backfill and foundation soil, distributed dead load surcharge, cohesion of the foundation soil and horizontal seismic acceleration. A comparative study between LRFD and allowable stress design (ASD) is also presented with a design example. 相似文献
4.
Based on the requirement of seismic reinforcement of bridge foundation on slope in the Chengdu-Lanzhou railway project, a shaking table model test of anti-slide pile protecting bridge foundation in landslide section is designed and completed. By applying Wenchuan seismic waves with different acceleration peaks, the stress and deformation characteristics of bridge pile foundation and anti-slide pile are analyzed, and the failure mode is discussed. Results show that the dynamic response of bridge pile and anti-slide pile are affected by the peak value of seismic acceleration of earthquake, with which the stress and deformation of the structure increase. The maximum dynamic earth pressure and the moment of anti-slide piles are located near the sliding surface, while that of bridge piles are located at the top of the pile. Based on the dynamic response of structure, local reinforcement needs to be carried out to meet the requirement of the seismic design. The PGA amplification factor of the surface is greater than the inside, and it decreases with the increase of the input seismic acceleration peak. When the slope failure occurs, the tension cracks are mainly produced in the shallow sliding zone and the coarse particles at the foot of the slope are accumulated. 相似文献
5.
以往对建筑抗震性影响因素的研究仅限于施工材料、技术手段等外部条件,忽略了基坑土体安全系数、基坑状态对建筑抗震性的影响,一定程度上削弱了建筑的抗震性能。本文从基坑排桩角度对建筑抗震性的影响展开分析,通过有限元强度折减法获取土体的安全系数与基坑状态的判断标准,在该标准下基于土体安全系数采用有限元强度折减法计算公式,获取各个土层计算参数。基于该参数使用ABAQUS有限元软件构建基坑排桩有限元分析模型(土体和桩体分别采用莫尔-库仑弹塑性模型和二维弹性模型)。实验采用所提分析方法,从基坑排桩排距、刚度两方面对建筑抗震性能进行分析。实验结果表明,当基坑排桩排距进行适当取值时,建筑抗震性越好;双排桩的刚度越大,建筑抗震性越好,且随着刚度的增加建筑抗震性能趋于平稳。 相似文献
6.
目前我国房屋建筑抗震采用的以小震弹性计算为基础的设计方法,使工程师忽视了对建筑结构在强烈地震作用下破坏模式的充分考虑与设计,使得建筑结构的大震安全性有时难以得到保证。＂破坏-安全＂抗震理念,以房屋建筑最重要的抗震安全性能为目标,要求设计人员对结构的预期破坏模式有充分的把握和控制,使结构在强烈地震作用下能够形成明确的预期破坏模式并具备一定的耗能能力,从而以经济的代价保证结构其余部分在强烈地震作用下的安全。本文结合我国汶川地震灾后恢复重建与加固改造的实际情况,介绍了＂破坏-安全＂抗震理念及其设计概念,并介绍了国内外研究人员与工程师在实现＂破坏-安全＂抗震理念方面所提出的创新抗震结构体系及其研究成果。希望＂破坏-安全＂这一抗震理念及其相关技术能够在我国广大的经济欠发达地区的抗震设计实践中得到推广,以全面提高我国经济欠发达地区房屋建筑的抗震安全性。 相似文献
7.
Performance-based seismic design of nonstructural building components:The next frontier of earthquake engineering 总被引：1，自引：1，他引：0
With the development and implementation of performance-based earthquake engineering,harmonization of performance levels between structural and nonstructural components becomes vital. Even if the structural components of a building achieve a continuous or immediate occupancy performance level after a seismic event,failure of architectural,mechanical or electrical components can lower the performance level of the entire building system. This reduction in performance caused by the vulnerability of nonstructural components has been observed during recent earthquakes worldwide. Moreover,nonstructural damage has limited the functionality of critical facilities,such as hospitals,following major seismic events. The investment in nonstructural components and building contents is far greater than that of structural components and framing. Therefore,it is not surprising that in many past earthquakes,losses from damage to nonstructural components have exceeded losses from structural damage. Furthermore,the failure of nonstructural components can become a safety hazard or can hamper the safe movement of occupants evacuating buildings,or of rescue workers entering buildings. In comparison to structural components and systems,there is relatively limited information on the seismic design of nonstructural components. Basic research work in this area has been sparse,and the available codes and guidelines are usually,for the most part,based on past experiences,engineering judgment and intuition,rather than on objective experimental and analytical results. Often,design engineers are forced to start almost from square one after each earthquake event: to observe what went wrong and to try to prevent repetitions. This is a consequence of the empirical nature of current seismic regulations and guidelines for nonstructural components. This review paper summarizes current knowledge on the seismic design and analysis of nonstructural building components,identifying major knowledge gaps that will need to be filled by future research. Furthermore,considering recent trends in earthquake engineering,the paper explores how performance-based seismic design might be conceived for nonstructural components,drawing on recent developments made in the field of seismic design and hinting at the specific considerations required for nonstructural components. 相似文献
8.
地震作用过程中地震加速度通常呈先增大后减小的特征。利用拟静力法对危岩的稳定性进行分析时,考虑地震过程中地震加速度的变化,对山西太原天龙山危岩体加固工程中的同一危岩体分别以滑塌式和倾倒式破坏模式进行计算,发现地震作用过程中危岩体可能在两种破坏失稳模式之间相互转化。将此问题扩展至一般情况进行计算并讨论,得出如下结论:地震力对危岩体破坏作用的贡献大小不同,通常情况下,地震作用力对危岩的倾覆力矩贡献相对较大;进行稳定性评价时应考虑地震作用过程,以安全系数最先达到1.0的破坏模式作为危岩体的可能破坏模式进行计算;对危岩体进行抗震加固设计时应对加固设计进行多种工况下的校核,保证其在地震作用过程中不同危险状态的稳定性。 相似文献
9.
《地震研究进展（英文）》2022,2(4):100175
A typical single-layer raw soil structure in villages and towns in China is taken as the research object. In the probabilistic seismic demand analysis, the seismic demand model is obtained by the incremental dynamic time history analysis method. The seismic vulnerability analysis is carried out for the raw soil structure of non-foundation, strip foundation, and spiral anchor composite foundation, respectively. The spiral anchor composite foundation can reduce the seismic response and failure state of raw soil structure, and the performance level of the structure is significantly improved. Structural requirements sample data with the same ground motion intensity are analyzed by linear regression statistics. Compared with the probabilistic seismic demand model under various working conditions, the seismic demand increases gradually with the increase of intensity. The seismic vulnerability curve is summarized for comparative analysis. With the gradual deepening of the limit state, the reduction effect of spiral anchor composite foundation on the exceedance probability becomes more and more obvious, which can reduce the probability of structural failure to a certain extent. 相似文献
10.
A safety format is proposed for the flexural design of reinforced concrete members for the combination of seismic and gravity loads, with load and resistance factors which depend on member type, on the value of the target theoretical probability of failure and on the ratio of the load effect due to gravity loads to that due to the nominal value of the seismic action, both obtained by elastic analysis. Safety factors are computed through an advanced Level II reliability procedure, using a limit state inequality between the member rotation ductility supply under monotonic loading and the peak rotation ductility and cyclic energy dissipation demands. Uncertainties considered are: for resistance, the uncertainty of failure under imposed cyclic deformations, and for action, the maximum peak ductility and energy dissipation demands in the structure's lifetime, as obtained through a series of non-linear dynamic analyses of multistorey buildings in 3D. using as input ensembles of bidirectional acceleration time-histories which describe probabilistically the extreme bidirectional seismic action in the structure's lifetime. Computed load and resistance factors are practically independent of the load-effects ratio. The load factor on the seismic action is found to be independent of member type and to increase with the theoretical probability of failure much faster than the elastic spectral value at the structure's fundamental period with probability of exceedance in the structure's lifetime. Simple rules for the dependence of the resistance modification factors on the theoretical failure probability are also derived. As for the computed values of the load factors the moment due to gravity loads is negligible in comparison to the factored seismic moment, a simplified safety checking inequality between the design flexural capacity and a reduced seismic moment is proposed, in which the ratio of the resistance to the load factor plays the role of a force reduction or effective behaviour factor for the member. 相似文献
11.
边坡地震稳定性分析探讨 总被引：16，自引：0，他引：16
传统的拟静力法和安全系数时程分析法在评价边坡地震稳定性时存在一定的局限性。在提出准确的评价边坡地震稳定性必需因素的基础上,建议对边坡地震稳定性分析方法重新进行分类。根据动力分析得到的边坡在地震作用下的破坏机制和破裂面的性质和位置,提出基于拉-剪破坏的动力时程分析法和强度折减动力分析法。第一种方法将FLAC计算得到破坏时刻的动应力施加到静力情况下边坡上,采用动力分析得到的拉-剪破裂面,结合极限平衡法求解边坡地震安全系数,是一种改进的动力有限元时程分析法;第二种方法考虑了拉-剪破坏的FLAC强度折减动力分析法,是完全动力的方法。最后通过算例分析验证了新方法的可行性,为边坡地震安全系数计算提供了一种新的思路。 相似文献
12.
顺层岩质边坡的抗震性指标大部分都是非确定的,无法用固定阈值衡量。提出基于非确定性分析法的顺层边坡抗震性性能研究,将顺层岩质边坡看作若干个叠加的薄板;运用非确定性分析法计算各个薄板的动力安全系数和动力极限状态方程,并对顺层边坡动力极限状态方程进行求解,可得在地震作用力下顺层边坡动力可靠度指标与顺层边坡失效概率之间的关系;评估地震作用力下顺层边坡整体稳定性,同时综合考量顺岩边坡的最小平均安全系数以及平均失效概率,得出评估结果。实验结果显示,在地震作用力下,顺层边坡坡高、坡角、岩层倾角对顺岩边坡抗震性能影响显著,评估结果与实际结果一致。 相似文献
13.
Offshore structures, such as composite breakwaters, are generally vulnerable to strong seismic wave propagating through loose or medium-dense seabed foundation. However, the seismically induced failure process of offshore structures is not well understood. In this study, seismic dynamics of a composite breakwater on liquefiable seabed foundation is investigated using a fully coupled numerical model FSSI-CAS 2D. The computation results show that the numerical model is capable of capturing a variety of nonlinear interaction phenomena between the composite breakwater and its seabed foundation. The numerical investigation demonstrates a three-stage failure process of the breakwater under seismic loading. In this process, the far-field seabed can become fully liquefied first, inducing excessive settlement of the structure, followed by significant lateral movement and tilting of the structure when the near-field soil progressively liquefies. The study demonstrates great promise of using advanced numerical analysis in geotechnical earthquake design of offshore structures. 相似文献
14.
以往对平面破坏模式的岩质边坡稳定性评价,主要关注潜在滑坡体在自重、坡体内静水压力和地震荷载耦合作用下沿破坏面的抗滑稳定性,并未涉及各类外荷载作用线不通过潜在滑体重心而引起的绕坡趾倾覆稳定性。针对这一问题,提出地震与张裂缝水压耦合作用下的岩质边坡倾覆稳定性解析方法,基于力矩平衡原理推导出岩质边坡抗倾覆稳定性系数的一般表达式;通过深入的变动参数比较研究,探讨张裂缝水压和地震荷载对抗倾覆安全系数的影响,认为水压是控制岩质边坡倾覆破坏的决定性因素,而地震荷载处于次要因素,其在一定程度上增加或减小抗倾覆稳定性。在此基础上建立不同参数组合下的岩质边坡抗倾覆稳定图,为工程技术人员快速评估饱水岩质边坡地震倾覆稳定性提供直接依据。 相似文献
15.
为了考虑地震波斜入射对坝后式厂房易损性的影响,通过斜入射SV波和P波波场叠加,在地表得到与实测地震动一致的设计地震动分量。同时为了考虑坝后式厂房的动力损伤,在程序中嵌入混凝土动力损伤本构,编写了可以考虑地震波斜入射体系的结构易损性分析程序。最后从太平洋地震工程研究中心（PEER）数据库中选取26条近场地震动数据,根据峰值地面加速度（PGA）对每条地震波进行调幅,以我国西南地区某坝后式厂房为工程实例,用增量动力学分析法计算了其上下游墙体在不同强度斜入射体系地震动作用下的易损性曲线。与传统垂直入射模式下的地震易损性曲线对比发现,传统垂直入射下的破坏概率较高,两种入射模式破坏概率最大相差26%。其中,坝后式厂房下游墙的破坏概率比上游墙大,最大相差可19%。因此坝后式厂房的抗震设计需考虑地震波斜入射的影响,并重点考虑下游墙部位的抗震安全性。 相似文献
16.
在一种新型无黏结预应力装配式混凝土梁柱框架节点抗震性能试验基础之上，使用基于位移的抗震设计方法对新型框架节点的无黏结预应力装配式钢筋混凝土框架结构进行整体抗震设计研究。首先使用有限元软件sap2000进行预应力三维结构设计并建立相应的有限元模型，同时建立该梁柱节点的梁恢复力模型，进而实现自定义塑性铰本构关系研究该装配式框架结构。使用pushover分析去表征结构的抗震性能，对比研究不同目标位移下的相应性能水平要求。通过施加Y方向均匀分布荷载对结构进行弹塑性推覆分析，对结构的层间位移角、破坏机制进行分析讨论。结果表明：按照"功能良好""生命安全""防止倒塌"三水平的设计均达到预期结果，各层层间位移角和薄弱层的性能均能满足规范的相应要求。并选用三条地震波对结构进行弹塑性动力时程分析，表明基于该新型梁柱节点的装配式结构在基于位移的抗震设计中可以较好满足相关抗震性能水平要求。 相似文献
17.
Soil failure can be used for seismic protection of structures 总被引：2，自引：2，他引：0
I. Anastasopoulos G. Gazetas M. Loli M. Apostolou N. Gerolymos 《Bulletin of Earthquake Engineering》2010,8(2):309-326
A new seismic design philosophy is illuminated, taking advantage of soil “failure” to protect the superstructure. Instead of over-designing the foundation to ensure that the loading stemming from the structural inertia can be “safely” transmitted onto the soil (as with conventional capacity design), and then reinforce the superstructure to avoid collapse, why not do exactly the opposite by intentionally under-designing the foundation to act as a “safety valve” ? The need for this “reversal” stems from the uncertainty in predicting the actual earthquake motion, and the necessity of developing new more rational and economically efficient earthquake protection solutions. A simple but realistic bridge structure is used as an example to illustrate the effectiveness of the new approach. Two alternatives are compared : one complying with conventional capacity design, with over-designed foundation so that plastic “hinging” develops in the superstructure; the other following the new design philosophy, with under-designed foundation, “inviting” the plastic “hinge” into the soil. Static “pushover” analyses reveal that the ductility capacity of the new design concept is an order of magnitude larger than of the conventional design: the advantage of “utilising” progressive soil failure. The seismic performance of the two alternatives is investigated through nonlinear dynamic time history analyses, using an ensemble of 29 real accelerograms. It is shown that the performance of both alternatives is totally acceptable for moderate intensity earthquakes, not exceeding the design limits. For large intensity earthquakes, exceeding the design limits, the performance of the new design scheme is proven advantageous, not only avoiding collapse but hardly suffering any inelastic structural deformation. It may however experience increased residual settlement and rotation: a price to pay that must be properly assessed in design. 相似文献
18.
随着国内外大跨桥梁特别是跨海桥梁建设的迅速发展,沉井基础在桥梁基础中所占的比例越来越大。虽然沉井基础作为1种刚性基础具有良好的力学性能,然而震害实践表明沉井基础在地震作用下也并非万无一失。通过分析国内外典型桥梁沉井基础的震害特征发现,沉井基础的地震破坏与桩基础有显著差异,且与埋置深度有直接关系;研究表明:地震作用下沉井基础的破坏机理及地基承载力与静力作用下明显不同,但目前在该方面的研究还较为欠缺;总结和对比了现有几种沉井基础-土相互作用研究方法,并分析了几种研究方法的优缺点和适用场合;同时也归纳和对比了各国抗震规范对桥梁沉井基础的基本规定、适用范围、计算方法和构造规定等方面的内容。最后结合现有的研究现状对沉井基础抗震性能研究的发展方向进行了展望,此外,随着我国跨海、跨江及跨库区大跨桥梁建设的发展,地震力和波浪力等多灾害因素共同作用下深水沉井基础桥梁破坏机理及设计方法的研究势在必行。 相似文献
19.
作为基于结构性能抗震设计的重要原则,“投资—效益”准则反映了抗震设计思想由只注重结构安全到综合考虑技术、经济、社会等诸多因素影响的转变,而结构性能水平和抗震性能目标是实现这一准则的前提和基础.采用五级结构性能水平细化现行规范给出的三水准设防,以层间位移角为定量指标,建立了结构性能水平与层间位移角限值之间一一对应的关系.提出抗震性能目标优化决策,根据最优设防烈度并引入地震危险性分析,建立了基于“投资—效益”准则的结构全寿命总费用模型.该模型规避了直接求解体系可靠度的复杂过程,将问题转化为求解结构的失效概率.其优点在于既能考虑结构的初始造价,又充分根据结构性能失效的特点考虑结构在各级性能水平下的损失期望,全面注重了结构性能、安全及经济等条件,体现了基于性能的抗震设计理念. 相似文献
20.
Recent studies have highlighted the potential advantages of allowing inelastic foundation response during strong seismic shaking. Such an alternative seismic design philosophy, in which soil failure is used as a “fuse” for the superstructure has recently been proposed, in the form of “rocking isolation”. Within this context, foundation rocking may be desirable as a means of bounding the inertia forces transmitted onto the superstructure, but incorporates the peril of unacceptable settlements in case of a low static factor of safety FSv. Hence, to ensure that rocking is materialized through uplifting rather than sinking, an adequately large FSv is required. Although this is feasible in theory, soil properties are not always well-known in engineering practice. However, since rocking-induced soil yielding is only mobilized within a shallow layer underneath the footing, “shallow soil improvement” is considered as an alternative approach to release the design from the jeopardy of unforeseen inadequate FSv. For this purpose, this paper studies the rocking response of relatively slender SDOF structures (h/B ratio equals 3 and rocking dominates over sliding), with emphasis on the effectiveness of shallow soil improvement stretching to various depths below the foundation. A series of reduced-scale monotonic and slow-cyclic pushover tests are conducted on SDOF systems lying on a square surface foundation. It is shown that shallow soil improvement may, indeed, be quite effective provided that its depth is equal to the width of the foundation. For lightly-loaded systems, an even shallower soil improvement may also be considered effective, depending on design requirements. The effectiveness of shallow soil improvement is ameliorated with the increase of cyclic rotation amplitude, and with repeating cycles of loading. 相似文献