共查询到19条相似文献，搜索用时 125 毫秒
1.
隔震结构中非经典阻尼影响及最佳阻尼比分析 总被引：15，自引：1，他引：14
本文采用双自由度非比例阻尼振动模型描述基础隔震体系,用拉普拉斯变换方法获得其地震时域响应的近似解析解,借助于应谱理论分析了非比例阻尼对隔震体系中的上部结构层间最大剪力及隔震层最大位移等响应值的影响,探寻了隔震系统最佳阻尼比的取值范围。 相似文献
2.
对一基础隔震钢筋混凝土框架结构在无填充墙情况下进行了环境激励下的动力测试,重点利用Hilbert-Huang变换与随机减量技术相结合的方法识别了其模态参数,并与随机子空间识别法、有理分式多项式法识别的结果进行了对比。识别结果表明在环境激励下,基础隔震结构的基本周期远小于多遇和罕遇地震工况下设计计算的基本周期;等效黏滞阻尼比很小,近乎于基础固定模型。对隔震层阻尼特性的分析表明,环境激励下可以将基础隔震结构视为经典的比例阻尼系统。进一步以识别的模态参数为基准,采用优化的方法数值反演了环境激励下该结构隔震层的实际水平等效刚度,结果表明其值为多遇地震下计算刚度取值的10.75倍。 相似文献
3.
隔震结构"小震不坏"的动力可靠度分析 总被引：7，自引：2，他引：5
本文探讨叠层橡胶隔震体系在“小震不坏”条件下的动力可靠度分析。基于等效线性化的隔震工程设计参数,建立非比例阻尼隔震结构模型。采用双过滤白噪声功率谱模型描述地震动,并用林家浩虚拟激励法进行随机响应分析。以各层的最大层间位移响应作为控制指标,取结构的弹性位移限值作为位移极限值,建立功能状态方程。根据一次二阶矩方法,用串联模式计算体系的总体可靠度。文末选用了一个7层隔震框架作为数值算例,探讨了隔震阻尼、寒冷环境、节点构造误差所引起的隔震层刚度上升,以及场地土类别等对体系动力可靠性的影响。 相似文献
4.
5.
层间隔震结构是由基础隔震结构发展而来的一种新型隔震结构。为研究层间隔震结构的倒塌,需先研究不同层间隔震结构的不同失效模式和失效位置,文章建立了3个不同结构参数的层间隔震结构有限元模型,选取20条与抗震规范反应谱吻合的地震动,采用增量动力分析（IDA）方法,分别对其失效模式和失效位置进行研究。研究表明:基于不同的结构参数,层间隔震的基本失效模式有三种,即隔震层水平位移超限导致结构失效、下部结构层间位移角超限导致结构失效、隔震层拉压应力超限导致结构失效;隔震层下部结构和隔震层最外边缘支座为结构的薄弱位置,应引起更多关注。此方法不仅可以研究结构的不同失效模式,还可以确定失效位置,可为下一步层间隔震结构的抗倒塌分析提供理论基础。 相似文献
6.
在基础隔震结构中,当上部结构层间刚度相对较小、垂直荷载较大,且采用的叠层橡胶垫的橡胶总厚度较大时,隔震支座不仅要产生水平变形,同时也会产生竖向变形,导致上部结构产生摆动.文中推导了基础隔震结构考虑摆动的运动和控制方程,分析研究了摆动对基础隔震结构的振动控制影响.研究结果表明:基础隔震结构的摆动对控制有一定影响;隔震层转动刚度、阻尼和上部结构垂直荷载对基础隔震结构考虑摆动的振动控制有明显影响. 相似文献
7.
高层隔震建筑的隔震层在罕遇地震作用下会产生拉应力。本文通过对一栋20层的高层隔震结构,分别采用等拉压刚度模型和不等拉压刚度模型进行动力非线性时程分析,研究叠层橡胶隔震支座竖向刚度模型对高层基础隔震结构动力响应的影响。研究表明,超出线弹性工作范围后,竖向等拉压刚度模型将会低估隔震层的竖向位移量,低估上部结构的动力响应。 相似文献
8.
层间隔震结构作为一种新型的隔震形式,不仅可以降低上部结构的动力响应,还可以弥补基础隔震结构的不足.现有研究多集中在远场地震作用下的规则层间隔震结构.本文利用通用结构分析与设计软件SAP2000分别模拟了一幢8层带裙房钢筋混凝土框架层间隔震结构、基础隔震结构和抗震结构,分析并对比了三种结构在近场地震作用下动力响应特征.结果表明在近场条件下三种结构顶层均出现不同程度的鞭梢效应;相比抗震结构两种隔震结构具有很好的减震效果,而且基础隔震结构的减震效果好于层间隔震结构;由于结构刚度突变的部位剪力较大,所以应对其裙楼顶部予以加强. 相似文献
9.
高层隔震建筑三维地震响应 总被引：5，自引：0，他引：5
对某高层框架－筒体结构进行了三维有限元时程分析，考虑了基础夹层橡胶了隔震垫的弹塑性特性和粘滞阻尼，分析了结构在地震波作用下的动力响应，为高层建筑中推广应用基础隔震技术提供了理论依据。 相似文献
10.
橡胶支座基础隔震结构遭遇近断层脉冲型地震动作用时,隔震层变形过大,需要限位。提出了软碰撞限位方案。按抗震规范设计橡胶支座隔震钢筋混凝土框架结构,选取近断层地震动记录,分析了限位主要参数预留距离、限位刚度和阻尼对隔震结构响应的影响。结果表明,预留距离增大,限位刚度需求增大,限位效果减弱;限位刚度增大,隔震层最大位移减小,上部结构层间最大位移增大;在一定范围内适当增大阻尼可减小隔震层最大位移与上部结构的层间最大位移。合理选用限位参数,可同时获得良好的限位与减震效果。提出了限位参数的优选方法。 相似文献
11.
There is no consensus at the present time regarding an appropriate approach to model viscous damping in nonlinear time‐history analysis of base‐isolated buildings because of uncertainties associated with quantification of energy dissipation. Therefore, in this study, the effects of modeling viscous damping on the response of base‐isolated reinforced concrete buildings subjected to earthquake ground motions are investigated. The test results of a reduced‐scale three‐story building previously tested on a shaking table are compared with three‐dimensional finite element simulation results. The study is primarily focused on nonlinear direct‐integration time‐history analysis, where many different approaches of modeling viscous damping, developed within the framework of Rayleigh damping are considered. Nonlinear direct‐integration time‐history analysis results reveal that the damping ratio as well as the approach used to model damping has significant effects on the response, and quite importantly, a damping ratio of 1% is more appropriate in simulating the response than a damping ratio of 5%. It is shown that stiffness‐proportional damping, where the coefficient multiplying the stiffness matrix is calculated from the frequency of the base‐isolated building with the post‐elastic stiffness of the isolation system, provides reasonable estimates of the peak response indicators, in addition to being able to capture the frequency content of the response very well. Furthermore, nonlinear modal time‐history analyses using constant as well as frequency‐dependent modal damping are also performed for comparison purposes. It was found that for nonlinear modal time‐history analysis, frequency‐dependent damping, where zero damping is assigned to the frequencies below the fundamental frequency of the superstructure for a fixed‐base condition and 5% damping is assigned to all other frequencies, is more appropriate, than 5% constant damping. Copyright © 2013 John Wiley & Sons, Ltd. 相似文献
12.
为了研究铅芯橡胶隔震支座的阻尼分布对平扭耦联隔震体系隔震效果的影响,本文对一个三层两跨钢框架,通过调整上部结构负重块位置及下部铅芯橡胶隔震支座的分布位置,进行不同偏心工况下平扭耦联隔震体系地震模拟振动台试验,获得了不同偏心工况、不同阻尼分布情况下结构位移和加速度的时程曲线。试验和分析表明:隔震层阻尼中心与上部结构的质心位置接近,或者增大隔震层的阻尼半径,可显著地降低上部结构的扭转反应。 相似文献
13.
John F. Hall 《地震工程与结构动力学》2006,35(5):525-545
Rayleigh damping is commonly used to provide a source of energy dissipation in analyses of structures responding to dynamic loads such as earthquake ground motions. In a finite element model, the Rayleigh damping matrix consists of a mass‐proportional part and a stiffness‐proportional part; the latter typically uses the initial linear stiffness matrix of the structure. Under certain conditions, for example, a non‐linear analysis with softening non‐linearity, the damping forces generated by such a matrix can become unrealistically large compared to the restoring forces, resulting in an analysis being unconservative. Potential problems are demonstrated in this paper through a series of examples. A remedy to these problems is proposed in which bounds are imposed on the damping forces. Copyright © 2005 John Wiley & Sons, Ltd. 相似文献
14.
Initial versus tangent stiffness‐based Rayleigh damping in inelastic time history seismic analyses 
下载免费PDF全文
下载免费PDF全文 In the inelastic time history analyses of structures in seismic motion, part of the seismic energy that is imparted to the structure is absorbed by the inelastic structural model, and Rayleigh damping is commonly used in practice as an additional energy dissipation source. It has been acknowledged that Rayleigh damping models lack physical consistency and that, in turn, it must be carefully used to avoid encountering unintended consequences as the appearance of artificial damping. There are concerns raised by the mass proportional part of Rayleigh damping, but they are not considered in this paper. As far as the stiffness proportional part of Rayleigh damping is concerned, either the initial structural stiffness or the updated tangent stiffness can be used. The objective of this paper is to provide a comprehensive comparison of these two types of Rayleigh damping models so that a practitioner (i) can objectively choose the type of Rayleigh damping model that best fits her/his needs and (ii) is provided with useful analytical tools to design Rayleigh damping model with good control on the damping ratios throughout inelastic analysis. To that end, a review of the literature dedicated to Rayleigh damping within these last two decades is first presented; then, practical tools to control the modal damping ratios throughout the time history analysis are developed; a simple example is finally used to illustrate the differences resulting from the use of either initial or tangent stiffness‐based Rayleigh damping model. Copyright © 2013 John Wiley & Sons, Ltd. 相似文献
15.
16.
Modeling viscous damping in nonlinear response history analysis of buildings for earthquake excitation 下载免费PDF全文
下载免费PDF全文 The Rayleigh damping model, which is pervasive in nonlinear response history analysis (RHA) of buildings, is shown to develop ‘spurious’ damping forces and lead to inaccurate response results. We prove that a viscous damping matrix constructed by superposition of modal damping matrices—irrespective of the number of modes included or values assigned to modal damping ratios—completely eliminates the ‘spurious’ damping forces. This is the damping model recommended for nonlinear RHA. Replacing the stiffness‐proportional part of Rayleigh damping by the tangent stiffness matrix is shown to improve response results. However, this model is not recommended because it lacks a physical basis and has conceptual implications that are troubling: hysteresis in damping force–velocity relationship and negative damping at large displacements. Furthermore, the model conflicts with the constant‐damping model that has been the basis for fundamental concepts and accumulated experience about the inelastic response of structures. With a distributed plasticity model, the structural response is not sensitive to the damping model; even the Rayleigh damping model leads to acceptable results. This perspective on damping provides yet another reason to employ the superior distributed plasticity models in nonlinear RHA. OpenSees software has been extended to include a damping matrix defined as the superposition of modal damping matrices. Although this model leads to a full populated damping matrix, the additional computational demands are demonstrated to be minimal. Copyright © 2015 John Wiley & Sons, Ltd. 相似文献
17.
基于动力可靠度的隔震结构参数模糊优化 总被引：1，自引：0，他引：1
分别选取Bouc—Wen和退化Bouc—Wen模型描述隔震层及上部结构滞变回复力，采用虚拟激励法进行隔震结构随机响应分析。用各层最大层间位移响应和累计疲劳损伤指数建立双参数的功能状态方程，用一次二阶矩理论计算隔震结构失效概率。选用一个隔震框架作为数值算例，探讨了低频过滤器、隔震阻尼比和隔震刚度对隔震结构各子系统条件失效概率的影响。建立了隔震结构参数多目标优化模型，用失效概率确定单因素评判的隶属度，并采用最大隶属度法对隔震参数进行模糊优化。 相似文献
18.
In many finite element platforms, a classical global damping matrix based on the elastic stiffness of the system (including isolators) is usually developed as part of the solution to the equations of motion of base-isolated buildings. The conducted analytical and numerical investigations illustrate that this approach can lead to the introduction of unintended damping to the first and higher vibration modes and the spurious suppression of the respective structural responses. A similar shortcoming might be observed even when a nonclassical damping model (ie, an assembly of the superstructure and isolation system damping sub-matrices) is used. For example, the use of Rayleigh damping approach to develop the superstructure damping sub-matrix can lead to the undesired addition of damping to the isolated mode arising from the mass-proportional component of the superstructure damping. On the other hand, the improper use of nonclassical stiffness-proportional damping (eg, determining the proportional damping coefficient, βk , based on the first mode) can result in assigning significant damping to the higher-modes and the unintended mitigation of the higher-mode responses. Results show that a nonclassical stiffness-proportional model in which βk is determined based on the second modal period of a base-isolated building can reasonably specify the intended damping to the higher modes without imparting undesirable damping to the first mode. The nonclassical stiffness-proportional damping can be introduced to the numerical model through explicit viscous damper elements attached between adjacent floors. In structural analysis software such as SAP2000®, the desired nonclassical damping can be also modeled through specifying damping solely to the superstructure material. 相似文献
19.
导管架式海洋平台结构阻尼隔振体系及其减振效果分析 总被引：10，自引：2，他引：10
导管架式海洋平台结构是当前应用最广的一种平台结构形式。本文研究导管架式海洋平台结构阻尼隔振体系及其减振效果。针对导管架式海洋平台结构的型式与特点，为了充分发挥阻尼器的耗能减振作用，提出了在平台结构导管架端帽和甲板之间设置柔性阻尼层的新型阻尼隔振方案。针对渤海JZ20－2MUQ平台结构，建立了海洋平台结构阻尼隔振体系简化计算模型，研究了隔振层参数与结构阻尼比的关系以及它们对结构整体和隔振层层间相对位移的控制效果；进行了多种冰荷载工况和地震工况的数值模拟。结果表明，阻尼隔振方案是导管架式海洋平台结构的一种有效的减振措施。 相似文献