首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 46 毫秒
1.
Air sparging was evaluated for remediation of tetrachloroethylene (PCE) present as dense nonaqueous phase liquid (DNAPL) in aquifers. A two-dimensional laboratory tank with a transparent front wall allowed for visual observation of DNAPL mobilization. A DNAPL zone 50 cm high was created, with a PCE pool accumulating on an aquitard. Detailed process control and analysis yielded accurate mass balances and insight into the mass-transfer limitations during air sparging. Initial PCE recovery rates were high, corresponding to fast removal of residual DNAPL within the zone influenced directly by air channels. The vadose zone DNAPL was removed within a few days, and the recovery in the extracted soil vapors decreased to low values. Increasing the sparge rate and pulsing the air injection led to improved mass recovery, as the pulsing induced water circulation and increased the DNAPL dissolution rate. Dissolved PCE concentrations both within and outside the zone of air channels were affected by the pulsing. Inside the sparge zone, aqueous concentrations decreased rapidly, matching the declining effluent PCE flux. Outside the sparge zone, PCE concentrations increased because highly contaminated water was pushed away from the air injection point. This overall circulation of water may lead to limited spreading of the contaminant, but accelerated the time-weighted average mass removal by 40% to 600%, depending on the aggressiveness of the pulsing. For field applications, pulsing with a daily or diurnal cycling time may increase the average mass removal rate, thus reducing the treatment time and saving in the order of 40% to 80% of the energy cost used to run the blowers. However, air sparging will always fail to remove DNAPL pools located below the sparge point because the air will rise upward from the top of a screen, unless very localized geological layers force the air to migrate horizontally. Unrecognized presence of DNAPL at chlorinated solvent sites residual and pools could potentially hamper success of air sparging cleanups, since the presence of small DNAPL pools, ganglia or droplets can greatly extend the treatment time.  相似文献   

2.
The influence of model dimensionality on predictions of mass recovery from dense non-aqueous phase liquid (DNAPL) source zones in nonuniform permeability fields was investigated using a modified version of the modular three-dimensional transport simulator (MT3DMS). Thirty-two initial two- (2D) and three-dimensional (3D) tetrachloroethene–DNAPL source zone architectures, taken from a recent modeling study, were used as initial conditions for this analysis. Commonly employed source zone metrics were analyzed to determine differences between 2D and 3D predictions: (i) down-gradient flux-averaged contaminant concentration, (ii) reductions in contaminant mass flux through a down-gradient boundary, (iii) source zone ganglia-to-pool (GTP) ratio, and (iv) time required to achieve a remediation objective. 3D flux-averaged contaminant concentrations were approximately 3.5 times lower than concentrations simulated in 2D. This difference was attributed to dilution of the contaminant concentrations down gradient of the source zone. Contaminant flux reduction predictions for a given mass recovery were generally 5% higher in 3D simulations than in 2D simulations. The GTP ratio declined over time as mass was recovered in both 2D and 3D simulations. Although the source longevity (i.e., time required to achieve 99.99% mass recovery) differed between individual 2D and 3D realizations, the mean source longevity for the 2D and 3D simulation ensembles was within 2%. 2D simulations tended to over-predict the time required to achieve lower mass recovery levels (e.g. 50% mass recovery) due to a smaller contaminated area exposed to uncontaminated water. These findings suggest that ensemble averages of 2D numerical simulations of DNAPL migration, entrapment, dissolution, and mass recovery in statistically homogenous, nonuniform media may provide reasonable approximations to average behavior obtained using simulations conducted in fully three-dimensional domains.  相似文献   

3.
Dense nonaqueous phase liquid (DNAPL) source areas containing chlorinated volatile organic compounds (cVOCs) such as trichloroethene (TCE) and perchloroethene (PCE) often give rise to significant dissolved plumes in groundwater, leading to the closure of downgradient water supply wells and creating vapor intrusion issues in buildings located above the plume. Hydraulic containment via pump‐and‐treat has often been implemented to limit migration but must continue indefinitely. Removal of the DNAPL source area by means such as in situ thermal remediation (ISTR) offers the potential to diminish or end the need for hydraulic containment if the associated dissolved plume attenuates sufficiently following source removal. A question often raised is whether this occurs or whether the back diffusion of contaminants from secondary sources such as low‐permeability lenses in the dissolved plume precludes it. The authors conducted DNAPL source removal using ISTR at dozens of sites. This paper presents a compilation of cases—10 separate DNAPL source areas at five project sites—where data indicate that the implementation of a thorough ISTR in a DNAPL source area can result in the attenuation of the associated dissolved plume, such that in several cases, long‐standing pump‐and‐treat systems could be turned off. Our findings contrast with recent assertions that aggressive source remediation may not be justifiable because dissolved plume concentrations will not decline sufficiently. We show that the application of ISTR can result in the thorough removal of the DNAPL source, effective diminution of dissolved plume groundwater concentrations, and achievement of drinking water standards.  相似文献   

4.
Hydraulic displacement is a mass removal technology suitable for stabilization of a dense, nonaqueous phase liquid (DNAPL) source zone, where stabilization is defined as reducing DNAPL saturations and reducing the risk of future pool mobilization. High resolution three-dimensional multiphase flow simulations incorporating a spatially correlated, heterogeneous porous medium illustrate that hydraulic displacement results in an increase in the amount of residual DNAPL present, which in turn results in increased solute concentrations in groundwater, an increase in the rate of DNAPL dissolution, and an increase in the solute mass flux. A higher percentage of DNAPL recovery is associated with higher initial DNAPL release volumes, lower density DNAPLs, more heterogeneous porous media, and increased drawdown of groundwater at extraction wells. The fact that higher rates of recovery are associated with more heterogeneous porous media stems from the fact that larger contrasts in permeability provide for a higher proportion of capillary barriers upon which DNAPL pooling and lateral migration can occur. Across all scenarios evaluated in this study, the ganglia-to-pool (GTP) ratio generally increased from approximately 0.1 to between approximately 0.3 and 0.7 depending on the type of DNAPL, the degree of heterogeneity, and the imposed hydraulic gradient. The volume of DNAPL recovered as a result of implementing hydraulic displacement ranged from between 9.4% and 45.2% of the initial release volume, with the largest percentage recovery associated with 1,1,1 trichloroethane, the least dense of the three DNAPLs considered.  相似文献   

5.
Pump and treat has been successful in significantly reducing the volatile organic contaminant concentrations in ground water in Santa Clara Valley. California. The California Regional Water Quality Control Board. San Francisco Bay Region, currently oversees 61 sites in Santa Clara Valley with operating pump-and-treat systems, of which 42 sites have been extracting ground water since at least 1987. This review- evaluates the effects of ground water extraction on contaminant concentrations at 37 of those 42 sites. The evaluation focuses on trichloroethane, trichloroethene, and dichloroethane, as these were the most prevalent contaminants encountered at the sites. The majority of sites obtained greater than 90 percent reduction in maximum concentrations for one or more of the three contaminants. While only one of the 37 sites obtained maximum contaminant levels (MCL) for all contaminants, six of the sites included in the analyses reached MCLs for one or more of the sampled contaminants, and an additional seven of the sites are near MCLs for al least one contaminant. Our findings indicate that, while pump and treat successfully reduced maximum concentrations al most of the sites reviewed, successful attempts to reduce maximum contaminant concentrations to below MCLs are limited.  相似文献   

6.
The release of stored dissolved contaminants from low permeability zones contributes to plume persistence beyond the time when dense nonaqueous phase liquid (DNAPL) has completely dissolved. This is fundamental to successfully meeting acceptable low concentrations in groundwater that are driven by site‐specific cleanup goals. The study goals were to assess the role of DNAPL entrapment morphology on mass storage and plume longevity. As controlled field studies are not feasible, two‐dimensional (2D) test tanks were used to quantify the significance of mass loading processes from source dissolution and stored mass rebound. A simple two‐layer soil domain representing a high permeable formation sand overlying a zone of lower permeability sand was used in the tests. DNAPL mass depletion through dissolution was monitored via X‐ray photon attenuation, and effluent samples were used to monitor the plume. These data enabled analysis of the DNAPL distribution, the dissolved plume, and the dissolved phase distribution within the low permeability layer. Tests in an intermediate tank showed that mass storage contributes substantially to plume longevity. Detectable effluent concentrations persisted long after DNAPL depletion. The small tank results indicated that the DNAPL morphology influenced the flow field and caused distinctive transport mechanisms contributing to mass storage. Zones of high DNAPL saturation at the interface between the low and high permeability layers exhibited flow bypassing and diffusion dominated transport into the low permeability layer. In the absence of a highly saturated DNAPL zone near the soil interface the contaminant penetrated deeper into the low permeability layer caused by a combination of advection and diffusion.  相似文献   

7.
At sites where a dense nonaqueous phase liquid (DNAPL) was spilled or released into the subsurface, estimates of the mass of DNAPL contained in the subsurface from core or monitoring well data, either in the nonaqueous or aqueous phase, can be highly uncertain because of the erratic distribution of the DNAPL due to geologic heterogeneity. In this paper, a multiphase compositional model is applied to simulate, in detail, the DNAPL saturations and aqueous-phase plume migration in a highly characterized, heterogeneous glaciofluvial aquifer, the permeability and porosity data of which were collected by researchers at the University of Tübingen, Germany. The DNAPL saturation distribution and the aqueous-phase contaminant mole fractions are then reconstructed by sampling the data from the forward simulation results using two alternate approaches, each with different degrees of sampling conditioning. To reconstruct the DNAPL source zone architecture, the aqueous-phase plume configuration, and the contaminant mass in each phase, one method employs the novel transition probability/Markov chain approach (TP/MC), while the other involves a traditional variogram analysis of the sampled data followed by ordinary kriging. The TP/MC method is typically used for facies and/or hydraulic conductivity reconstruction, but here we explore the applicability of the TP/MC method for the reconstruction of DNAPL source zones and aqueous-phase plumes. The reconstructed geometry of the DNAPL source zone, the dissolved contaminant plume, and the estimated mass in each phase are compared using the two different geostatistical modeling approaches and for various degrees of data sampling from the results of the forward simulation. It is demonstrated that the TP/MC modeling technique is robust and accurate and is a preferable alternative compared to ordinary kriging for the reconstruction of DNAPL saturation patterns and dissolved-phase contaminant plumes.  相似文献   

8.
Field investigations were carried out to determine the occurrence of tetrachloroethene (PCE) dense nonaqueous phase liquid (DNAPL), the source zone architecture and the aquitard integrity at a 30‐ to 50‐year old DNAPL release site. The DNAPL source zone is located in the clay till unit overlying a limestone aquifer. The DNAPL source zone architecture was investigated through a multiple‐lines‐of‐evidence approach using various characterization tools; the most favorable combination of tools for the DNAPL characterization was geophysical investigations, membrane interface probe, core subsampling with quantification of chlorinated solvents, hydrophobic dye test with Sudan IV, and Flexible Liner Underground Technologies (FLUTe) NAPL liners with activated carbon felt (FACT). While the occurrence of DNAPL was best determined by quantification of chlorinated solvents in soil samples supported by the hydrophobic dye tests (Sudan IV and NAPL FLUTe), the conceptual understanding of source zone architecture was greatly assisted by the indirect continuous characterization tools. Although mobile or high residual DNAPL (S t > 1%) only occurred in 11% of the source zone samples (intact cores), they comprised 86% of the total PCE mass. The dataset, and associated data analysis, supported vertical migration of DNAPL through fractures in the upper part of the clay till, horizontal migration along high permeability features around the redox boundary in the clay till, and to some extent vertical migration through the fractures in the reduced part of the clay till aquitard to the underlying limestone aquifer. The aquitard integrity to DNAPL migration was found to be compromised at a thickness of reduced clay till of less than 2 m.  相似文献   

9.
Hadley PW  Newell CJ 《Ground water》2012,50(5):669-678
Groundwater remediation technologies are designed, installed, and operated based on the conceptual models of contaminant hydrogeology that are accepted at that time. However, conceptual models of remediation can change as new research, new technologies, and new performance data become available. Over the past few years, results from multiple-site remediation performance studies have shown that achieving drinking water standards (i.e., Maximum Contaminant Levels, MCLs) at contaminated groundwater sites is very difficult. Recent groundwater research has shown that the process of matrix diffusion is one key constraint. New developments, such as mass discharge, orders of magnitude (OoMs), and SMART objectives are now being discussed more frequently by the groundwater remediation community. In this paper, the authors provide their perspectives on the existing "reach MCLs" approach that has historically guided groundwater remediation projects, and advocate a new approach built around the concepts of OoMs and mass discharge.  相似文献   

10.
In situ chemical oxidation (ISCO) with activated persulfate is commonly used for the remediation of petroleum impacted soil and groundwater because of its proven efficiency and the perception that reaction end products are completely innocuous. While the reaction products are less hazardous compared to the contaminants being treated, they may inadvertently prolong site closure in areas that have adopted the U.S. Environmental Protection Agency (EPA) Secondary Maximum Contaminant Levels (SMCLs) as enforceable standards. This study examines the occurrence and persistence of iron, manganese, sulfate, sodium, and total dissolved solids (TDS) in groundwater following persulfate ISCO. The concentrations of these chemicals were observed remaining above their respective regulatory criteria almost 3 years following the chemical application. Background concentrations and mobilization due to the petroleum contamination and ISCO application are also evaluated. Baseline sampling revealed substantially higher iron and manganese concentrations inside the plume area compared to the upgradient and downgradient wells suggesting mobilization due to redox reactions occurring inside of the plume. Iron was not a component in the applied chemical formula, yet the iron concentration spiked by 366% in the key monitoring well during the first post-remediation monitoring event. Ionic interactions between the ISCO amendment and native soils are believed to be responsible for displacing significant quantities of iron from the soil. Sulfate, sodium, and TDS exceedances are primarily associated with decomposition products of the ISCO amendments. The iron, manganese, sulfate, sodium, and TDS concentrations are trending downward over time, but still exceed regulatory criteria or pre-ISCO concentrations.  相似文献   

11.
The performance of cyclodextrin (CD)‐enhanced push‐pull (PP) and line‐drive (LD) approaches to remediation of a site contaminated with a multicomponent dense nonaqueous phase liquid (DNAPL) present in a surficial sandy aquifer was evaluated in this field study. The treatment techniques were compared to each other and to the projected performance of a conventional water‐flushing system. Performance was assessed based on contaminant mass removed per unit volume of extraction solution and per unit time of operation. As expected, the CD‐enhanced LD and PP approaches to remediation were more efficient than conventional flushing with water. Between the two techniques, the PP approach performed 1.5 to 2 times better than the LD approach, particularly for higher DNAPL saturation of the source zone. This result suggests that forcing the flushing solution directly into and through the DNAPL source zone minimized flow bypassing and consequently resulted in a more efficient transfer of contaminant mass between the DNAPL phase and the flushing solution. Nonuniform treatment zone contaminant concentrations and changes in contaminant composition influenced the treatment performances, but these effects were small and still permitted the comparison of successive tests. Although CD was used as the solubility‐enhancing flushing agent in this study, it is likely that the results can be transferred to other chemically enhanced flushing technologies that use, for example, surfactants or alcohols.  相似文献   

12.
A field demonstration was performed at Edwards Air Force Base to assess bioaugmentation for treatment of a well‐characterized tetrachloroethene (PCE) dense nonaqueous phase liquid (DNAPL) source area in fractured rock. Groundwater recirculation was employed to deliver remedial amendments, including bacteria, to facilitate reductive dechlorination and enhance DNAPL dissolution. An active treatment period of 9 months was followed by a 10‐month posttreatment rebound evaluation. Dechlorination daughter products were observed in both the shallow and deep fracture zones following treatment. In the shallow fracture zone, the calculated DNAPL mass removed was approximately equal to the DNAPL mass estimated using partitioning tracer testing, and no rebound in chlorinated ethenes or ethene was observed during the posttreatment period. A maximum DNAPL dissolution enhancement factor of 5 was observed in the shallow fracture zone. In the deep fracture zone, only approximately 45% of the DNAPL mass—as estimated via partitioning tracer testing—was removed and rebound in the total molar chlorinated ethenes + ethene was observed. The difference in behavior between the shallow and deep fracture zones was attributed to DNAPL architecture and the fracture flow field.  相似文献   

13.
《Advances in water resources》2007,30(6-7):1547-1561
Recent laboratory experimental evidence has suggested that bioremediation may be an attractive management strategy for dense non-aqueous phase liquid (DNAPL) source-zones. In particular, metabolic reductive dechlorination has been shown to reduce aqueous phase chlorinated ethene contaminant concentrations and enhance DNAPL dissolution, reducing source longevity. Transitioning this technology from the laboratory to the field will be facilitated by tools capable of simulating bioenhanced dissolution. This work presents a mathematical model for metabolic reductive dechlorination in a macroscale two-phase (aqueous-organic) environment. The model is implemented through adaptation of an existing multi-phase compositional simulator, which has been modified to incorporate eight chemical components and four microbial populations: a fermentative population, two dechlorinating populations, and a competitor population (e.g., methanogens). Monod kinetics, modified to incorporate electron donor thresholds, electron acceptor competition, and competitor inhibition, are used to simulate microbial growth and component degradation. The developed model is numerically verified and demonstrated through comparisons with published column-scale dechlorination data. Dechlorination kinetics, electron donor concentrations, and DNAPL saturation and distribution are all found to affect the extent of dissolution enhancement, with enhancements ranging from 1.0 to ∼1.9. Comparison of simulation results with those from a simplified analytic modeling approach suggest that the analytical model may tend to over-predict dissolution enhancement and fail to account for the transient nature of dissolution enhancement, leading to significant (70%) under-prediction of source longevity.  相似文献   

14.
The closure of sites with identified or suspected DNAPL (dense nonaqueous phase liquids) under the requirements of the Resources Conservation and Recovery Act of 1976 (RCRA), or the Comprehensive Environmental Response, Compensation and Liability Act of 1980 (CERCLA) has not been well defined. With respect to RCRA, the U.S. Environmental Protection Agency (EPA) has required that all contamination must be removed at closure such that no residual risk to human health or the environment remains. Therefore, even though many states administering the RCRA program have adopted or are considering Risk-Based Corrective Action (RBCA) procedures (including the statistical methods described in SW-846) for RCRA closure, the treatment of DNAPL is, at best, challenging.
The methodology for closure in CERCLA is described in "Risk Assessment Guidelines for Super-fund (RAGS)," which requires that risks above the National Contingency Plan criteria must be remediated, preferably by on-site or in situ destruction. Most risk-based Brownfield or voluntary cleanup programs do not provide any explicit allowance for DNAPL. However, while the ASTM methodology for RBCA in E1739-95 (ASTM 1995) does not explicitly treat the problem of DNAPL, a basic framework for DNAPL assessment is implicitly provided.
A uniform methodology for RBCA closure of VOC (volatile organic compounds) DNAPL sites can be used to achieve the program objectives of RCRA, CERCLA, and Brownfield or voluntary cleanup programs. The regulatory acceptance of the application of RBCA methods to DNAPL sites will require education and discussion, but the use of a uniform methodology should facilitate acceptance.  相似文献   

15.
Invasion percolation (IP) models of dense non‐aqueous phase liquid (DNAPL) invasion into saturated horizontal fractures typically neglect viscous and gravity forces, as it is assumed that capillarity dominates in many situations. An IP model simulating DNAPL invasion into saturated horizontal fractures was modified to include gravity as a local effect. The model was optimized using a genetic algorithm, and demonstrated that the inclusion of gravity is important for replicating the architecture of the DNAPL invasion pattern. The optimized gravity‐included simulation showed the DNAPL invasion pattern to be significantly more representative of the experimentally observed pattern (80% accuracy) than did the optimized gravity‐neglected simulation (70% accuracy). Additional simulations of DNAPL invasion in 360 randomly generated fractures were compared with and without gravity forces. These simulations showed that with increasing fracture roughness, the minimum difference between simulations with and without gravity increases to 35% for a standard deviation of the mid‐aperture elevation field (SDz) of 10 mm. Even for low roughness (SDz = 0.1 mm), the difference was as high as 30%. Furthermore, a scaled Bond Number is defined which includes data regarding DNAPL type, media type and statistical characteristics of the fracture. The value of this scaled Bond Number can be used to determine the conditions under which gravity should be considered when simulating DNAPL invasion in a macroscopically horizontal fracture. Finally, a set of equations defining the minimum and maximum absolute percentage difference between gravity‐included and gravity‐neglected simulations is presented based on the fracture and DNAPL characteristics.  相似文献   

16.
The spontaneous expansion and mobilization of discontinuous gas above dense non-aqueous-phase liquid (DNAPL) pools can affect the aqueous-phase concentrations of the DNAPL constituents above the pool. The results of an intermediate-scale, two-dimensional flow cell experiment showed that the discontinuous gas flow produced by spontaneous expansion, driven by the partitioning of 1,1,1-TCA from the surface of a DNAPL pool, resulted in detectable aqueous-phase concentrations of 1,1,1-TCA well above the pool surface. In comparison to a conventional model for DNAPL pool dissolution in the absence of a discontinuous gas phase, these concentrations were greater than expected, and were present at greater than expected elevations. Additionally, this study showed that the discontinuous gas flow produced transient behavior in the aqueous-phase concentrations, where the elevated concentrations occurred as short-term, pulse-like events. These results suggest that the spontaneous expansion and mobilization of discontinuous gas in DNAPL source zones could lead to the misdiagnosis of source zone architecture using aqueous concentration data, and that the transient nature of the elevated concentrations could further complicate the difficult task of source zone characterization.  相似文献   

17.
Free-phase DNAPL recovery operations are becoming increasingly prevalent at creosote-contaminated aquifer sites. This paper illustrates the potential of both classical and innovative recovery methods. The UTCHEM multiphase flow and transport numerical simulator was used to predict the migration of creosote DNAPL during a hypothetical spill event, during a long-term redistribution after the spill, and for a variety of subsequent free-phase DNAPL recovery operations. The physical parameters used for the DNAPL and the aquifer in the model are estimates for a specific creosote DNAPL site. Other simulations were also conducted using physical parameters that are typical of a trichloroethene (TCE) DNAPL. Dramatic differences in DNAPL migration were observed between these simulations.  相似文献   

18.
This paper investigates numerical optimization of dense nonaqueous phase liquid (DNAPL) site remediation design considering effects of prediction and measurement uncertainty. Results are presented for a hypothetical problem involving remediation using thermal source reduction (TSR) and bioremediation with electron donor (ED) injection. Pump-and-treat is utilized as a backup measure if compliance criteria are not met. Remediation system design variables are optimized to minimize expected net present value (ENPV) cost. Adaptive criteria are assumed for real-time control of TSR and ED duration. Source zone dissolved concentration data enabled more reliable and lower cost operation of TSR than soil concentration data, but using both soil and dissolved data improved results sufficiently to more than offset the additional cost. Decisions to terminate remediation and monitoring or to initiate pump-and-treat are complicated by measurement noise. Simultaneous optimization of monitoring frequency, averaging period, and lookback periods to confirm decisions, in addition to remediation design variables, reduced ENPV cost. Results indicate that remediation design under conditions of uncertainty is affected by subtle interactions and tradeoffs between design variables, compliance rules, site characteristics, and uncertainty in model predictions and monitoring data. Optimized designs yielded cost savings of up to approximately 50% compared with a nonoptimized design based on common engineering practices. Significant improvements in accuracy and reductions in cost were achieved by recalibrating the model to data collected during remediation and re-optimizing design variables. Repeating this process periodically is advisable to minimize total costs and maximize reliability.  相似文献   

19.
The recovery of coal tar or creosote, which are dense nonaqueous phase liquids (DNAPLs), from the subsurface has been used as a means of site remediation at several former manufactured-gas plant sites and wood-treating facilities. Surface-active components in these complex DNAPL can have acid/base and surfactant characteristics that can significantly affect the wettability in these systems, with a reversal to DNAPL wetting at low pHs. These changes in wettability as a function of pH were employed to evaluate their significance on waterflooding efficiency in one-dimensional soil columns. The use of pH as a means of controlling wettability resulted in identical density and viscosity properties between the water-and DNAPL-wet conditions. At some of the higher pHs, the interracial tension changed as well as the wettability. Maintaining a constant dimensionless capillary number was used to minimize the effect of this variable. DNAPL saturations remaining in the DNAPL-wet systems after waterflooding ranged from 38% to 47%. Significantly lower final DNAPL saturations were achieved for water-wetting systems (15% to 30%).  相似文献   

20.
Remediation of dense nonaqueous phase liquids (DNAPLs) is recognized as one of the most difficult problems associated with ground water pollution. The pump-and-treat technique, usually consisting of a continuous operation of extraction-injection wells, is widely used for ground water remediation. In a stratified or otherwise heterogeneous aquifer, however, this technique suffers from tailing and rebound problems, which limit its cleanup efficiency and result in higher operation costs. The tailing and rebound is usually due to slow diffusion of contaminants out of lower- permeability heterogeneities into the flow regime of the higher-permeability zone. In this study, we conduct bench-scale experiments to investigate a novel polymer system and injection method to improve the pump-and-treat technique for DNAPL trapped in a layer of porous media that has a relatively low permeability compared to the surrounding media. This technique might be useful, for example, to remove DNAPL from these low-permeability zones after removal of DNAPL from the higher-permeability zones by a more traditional remediation method. The polymer system consists of a mixture of anionic and cationic polyacrylamides in solution and the injection method is based on flow-induced polymer adsorption, called bridging adsorption. The study includes single and parallel-column experiments. The measured polymer penetration depths were compared with values predicted from a numerical simulation, which was developed previously by the authors of this paper. The experiments and simulations show that the polymer injection leads to a modification of the permeability contrast that favors a more efficient pump-and-treat process. These results suggest that additional research to upscale the technology to pilot scales is warranted.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号