共查询到20条相似文献，搜索用时 125 毫秒
1.
Plan asymmetric buildings are very susceptible to earthquake induced damage due to lateral torsional coupling, and the corners of these systems suffer heavy damage during earthquakes. Therefore, it is important to investigate the seismic behavior of an asymmetric plan building with MR dampers. In this study, the effectiveness of MR damper-based control systems has been investigated for seismic hazard mitigation of a plan asymmetric building. Furthermore, the infl uence of the building parameters and damper command voltage on the control performance is examined through parametric study. The building parameters chosen are eccentricity ratio and frequency ratio. The results show that the MR damper-based control systems are effective for plan asymmetric systems. 相似文献
2.
Wenshen Pong Zu-Hsu Lee Anson Lee 《地震工程与工程振动(英文版)》2006,5(1):49-60
This study focuses on the comparison of the Uniform Building Code （UBC） 1997 and International Building Code （IBC） 2003 in relation to the seismic design and analysis of special steel moment resisting frame buildings （SMRF）. This paper formulates a numerical study of a steel SMRF building, studied in four different situations, namely： as an office building in San Francisco; as an office building in Sacramento; as an essential facility in San Francisco, and as an essential facility in Sacramento. The analytical results of the model buildings are then compared and analyzed taking note of any significant differences. This case study explores variations in the results obtained using the two codes, particularly the design base shear and drift ratios as they relate to different locations and occupancy use. This study also proves that IBC 2003 is more stringent for the redundancy factor under design category E for the SMRF building, and drift limits for essential facilities. 相似文献
3.
This paper describes a nonlinear finite element （FE） analysis of high strength concrete （HSC） columns, and verifies the results through laboratory experiments. First, a cyclically lateral loading test on nine cantilever column specimens of HSC is described and a numerical simulation is presented to verify the adopted FE models. Next, based on the FE model for specimen No.6, numerical simulations for 70 cases, in which different concrete strengths, stirrup ratios and axial load ratios are considered, are presented to explore the effect of these parameters on the behavior of the HSC columns, and to check the rationality of requirements for these columns specified in the China Code for Seismic Design of Buildings （GB 50011- 2001）. In addition, three cases with different stirrup strengths are analyzed to investigate their effect on the behavior of HSC columns. Finally, based on the numerical results some conclusions are presented. 相似文献
4.
Yanju Peng Yuejun Lu Jiaquan Yan Rongyu Tang Junqin Wang Jiagang Li 《地震工程与工程振动(英文版)》2010,9(2):223-231
This paper analyzes the seismicity in Bohai Sea,introducing a shape factor K to characterize the seismic risk distribution in sub-regions of the sea. Based on the seismic design ground motions for 46 platforms located in the Bohai Sea,a statistical analysis was performed for different peak ground acceleration (PGA) ratios at two different probability levels. In accordance with the two-stage design method,a scheme of two seismic design levels is proposed,and two seismic design objectives are established respectively for the strength level earthquake and the ductility level earthquake. By analogy with and comparison to the Chinese seismic design code for buildings,it is proposed that the probability level for the strength level earthquake and ductility level earthquake have a return period of 200 and 1000 - 2500 years,respectively. The validity of these proposed values is discussed. Finally,the PGAs corresponding to these two probability levels are calculated for different sub-regions of the Bohai Sea. 相似文献
5.
Linlin Gu Feng Zhang Xiaohua Bao Zhenming Shi Guanlin Ye Xianzhang Ling 《地震工程与工程振动(英文版)》2018,17(2):325-342
A large number of breakwaters have been constructed along coasts to protect humans and infrastructures from tsunamis.There is a risk that foundation soils of these structures may liquefy,or partially liquefy during the earthquake preceding a tsunami,which would greatly reduce the structures’capacity to resist the tsunami.It is necessary to consider not only the soil’s liquefaction behavior due to earthquake motions but also its post-liquefaction behavior because this behavior will affect the breakwater’s capacity to resist an incoming tsunami.In this study,numerical tests based on a sophisticated constitutive model and a soil-water coupled finite element method are used to predict the mechanical behavior of breakwaters and the surrounding soils.Two real breakwaters subjected to two different seismic excitations are examined through numerical simulation.The simulation results show that,earthquakes affect not only the immediate behavior of breakwaters and the surrounding soils but also their long-term settlements due to post-earthquake consolidation.A soil profile with thick clayey layers beneath liquefied soil is more vulnerable to tsunami than a soil profile with only sandy layers.Therefore,quantitatively evaluating the seismic behavior of breakwaters and surrounding soils is important for the design of breakwater structures to resist tsunamis. 相似文献
6.
This paper presents an experimental investigation on semi-active seismic response control of a multistory building with a podium structure using multiple magnetorheological (MR) dampers manipulated by a logic control algorithm. The experiments are performed in three phases on a seismic simulator with a slender 12-story building model representing a multi-story building and a relatively stiff 3-story building model typifying a podium structure. The first phase of the investigation is to assess control performance of using three MR dampers to link the 3-story building to the 12-story building, in which seismic responses of the controlled two buildings are compared with those of the two buildings without any connection and with rigid connection. The second phase is to investigate reliability of the semi-active control system and robustness of the logic control algorithm when 2 out of 3 MR dampers fail and when the electricity supply to MR dampers is completely stopped. The last phase is to examine sensitivity of semi-active control performance of two buildings to change in ground excitation. The experimental results show that multiple MR dampers with the logic control algorithm can achieve a significant reduction in seismic responses of both buildings. The proposed semi-active control system is of high reliability and good robustness. 相似文献
7.
Performance-based methodology for assessing seismic vulnerability and capacity of buildings 总被引：1，自引：0，他引：1
This paper presents a performance-based methodology for the assessment of seismic vulnerability and capacity of buildings. The vulnerability assessment methodology is based on the HAZUS methodology and the improved capacity- demand-diagram method. The spectral displacement (Sd) of performance points on a capacity curve is used to estimate the damage level of a building. The relationship between Sd and peak ground acceleration (PGA) is established, and then a new vulnerability function is expressed in terms of PGA. Furthermore, the expected value of the seismic capacity index (SCev) is provided to estimate the seismic capacity of buildings based on the probability distribution of damage levels and the corresponding seismic capacity index. The results indicate that the proposed vulnerability methodology is able to assess seismic damage of a large number of building stock directly and quickly following an earthquake. The SCev provides an effective index to measure the seismic capacity of buildings and illustrate the relationship between the seismic capacity of buildings and seismic action. The estimated result is compared with damage surveys of the cities of Dujiangyan and Jiangyou in the M8.0 Wenchuan earthquake, revealing that the methodology is acceptable for seismic risk assessment and decision making. The primary reasons for discrepancies between the estimated results and the damage surveys are discussed. 相似文献
8.
Hemchandra Chaulagain Hugo Rodrigues Enrico Spacone Ramesh Guragain Radhakrishna Mallik Humberto Varum 《地震工程与工程振动(英文版)》2014,13(3):455-470
Most current seismic design includes the nonlinear response of a structure through a response reduction factor(R). This allows the designer to use a linear elastic force-based approach while accounting for nonlinear behavior and deformation limits. In fact, the response reduction factor is used in modern seismic codes to scale down the elastic response of a structure. This study focuses on estimating the actual ‘R' value for engineered design/construction of reinforced concrete(RC) buildings in Kathmandu valley. The ductility and overstrength of representative RC buildings in Kathmandu are investigated. Nonlinear pushover analysis was performed on structural models in order to evaluate the seismic performance of buildings. Twelve representative engineered irregular buildings with a variety of characteristics located in the Kathmandu valley were selected and studied. Furthermore, the effects of overstrength on the ductility factor, beam column capacity ratio on the building ductility, and load path on the response reduction factor, are examined. Finally, the results are further analyzed and compared with different structural parameters of the buildings. 相似文献
9.
Seismic ground faulting is the greatest hazard for continuous buried pipelines.Over the years,researchers have attempted to understand pipeline behavior mostly via numerical modeling such as the finite element method.The lack of well-documented field case histories of pipeline failure from seismic ground faulting and the cost and complicated facilities needed for full-scale experimental simulation mean that a centrifuge-based method to determine the behavior of pipelines subjected to faulting is best to verify numerical approaches.This paper presents results from three centrifuge tests designed to investigate continuous buried steel pipeline behavior subjected to normal faulting.The experimental setup and procedure are described and the recorded axial and bending strains induced in a pipeline are presented and compared to those obtained via analytical methods.The influence of factors such as faulting offset,burial depth and pipe diameter on the axial and bending strains of pipes and on ground soil failure and pipeline deformation patterns are also investigated.Finally,the tensile rupture of a pipeline due to normal faulting is investigated. 相似文献
10.
<正>This paper describes shaking table tests of a 1:12 scale model of a special concentrically braced steel frame with pinned connections,which was fabricated according to a one-bay braced frame selected from a typical main factory building of a large thermal power plant.In order to investigate the seismic performance of this type of structure,several ground motion accelerations with different levels for seismic intensityⅧ,based on the Chinese Code for Seismic Design of Buildings,were selected to excite the model.The results show that the design methods of the members and the connections are adequate and that the structural system will perform well in regions of high seismicity.In addition to the tests,numerical simulations were also conducted and the results showed good agreement with the test results.Thus,the numerical model is shown to be accurate and the beam element can be used to model this structural system. 相似文献
11.
本文采用耗能减震技术，根据建筑结构抗震规范规定的反应谱法，利用ＣＴＡＢ程序对云南省洱源县振戎中学食堂进行了抗震计算分析和设计验算．首先对未加耗能减震装置的空框架结构进行了小震下的位移和强度验算以及大震下的位移验算；其次，介绍了本工程选用的Ｔ字芯板摩擦耗能器的工作原理，并对耗能器进行了足尺性能试验；第三，根据工程结构的环境特点和建筑使用功能要求，确定了耗能减震方案；最后，对耗能减震结构进行了抗震验算和分析，结果表明，附加耗能器后的工程结构抗震性能得到了明显改善． 相似文献
12.
振戎中学食堂楼耗能减震分析与设计(Ⅰ)－反应谱法 总被引：2，自引：0，他引：2
本文采用耗能减震技术，根据建筑结构抗震规范规定的反应谱法，利用CTAB程序对云南省洱源县振戎中学食堂进行了抗震计算分析和设计验算。首先对未加耗能减震装置的空框架结构进行了小震下的位移和强度验算以及大震下的位移验算；其次，介绍了本工程选用的T字芯板摩擦耗能器的工作原理，并对耗能器进行了足尺性能试验；第三，根据工程结构的环境特点和建筑使用功能要求，确定了耗能减震方案；最后，对耗能减震结构进行了抗震验算和分析，结果表明，附加耗能器后的工程结构抗震性能得到了明显改善。 相似文献
13.
A new steel framing system for seismic protection of timber platform frame buildings. Implementation with hysteretic energy dissipators 
下载免费PDF全文
下载免费PDF全文 This paper describes a new seismic protection system for timber platform frame buildings, either for new construction or retrofit. The system consists in connecting the timber frame to a steel structure that includes hysteretic energy dissipators designed to absorb most of the seismic input energy thus protecting the timber frame and the other steel members; alternatively, the system might use other types of dissipative devices. The steel structure consists of four steel stacks (located at each of the four façades) and steel collectors embracing each slab; the stacks and the collectors are connected, at each floor level, through the energy dissipators. The steel structure is self‐supporting, that is, the timber frame is not affected by horizontal actions and can be designed without accounting for any seismic provision; in turn, the steel members do not participate in the main load‐carrying system. The timber‐steel interface is designed to avoid any stress concentration in the transfer of horizontal forces and to guarantee that the yielding of the dissipators occurs prior to any timber failure. The energy dissipation capacity of the suggested system is discussed, and an application example on a six‐story timber building is presented; this case corresponds to highly demanding conditions because of the relatively large building height and weight, the high local seismicity, and the soft soil condition. This research belongs to a wider project aiming to promote the structural use of timber by improving the seismic capacity of wooden buildings; this research includes experiments and advanced numerical simulation. Copyright © 2014 John Wiley & Sons, Ltd. 相似文献
14.
Multi‐storey main buildings constructed with a low‐rise podium structure possess some architectural merits but the setback features of such a building complex may lead to seismic response enlargement of the main buildings. This paper explores the possibility of using passive friction dampers to connect the podium structure to the main buildings to prevent their seismic response enlargement without violating the architectural features. A series of shaking table tests were carried out on one 3‐storey and one 12‐storey building models in fully‐separated, rigidly connected, and friction damper‐linked configurations. Four sets of seismic ground motions were selected as inputs to the shaking table. The control competence of two buildings linked with friction damper was evaluated by comparison of their responses with those from fully‐separated and rigidly connected cases. Experimental results showed that unfavourable seismic response amplification did occur in the building complex in the rigidly connected case. By contrast, friction damper showed effectiveness in reducing absolute acceleration and interstorey drift responses of both buildings if friction force level was appropriately applied. Copyright © 2005 John Wiley & Sons, Ltd. 相似文献
15.
Tuned mass dampers for response control of torsional buildings 总被引：1，自引：0，他引：1
This paper presents an approach for optimum design of tuned mass dampers for response control of torsional building systems subjected to bi‐directional seismic inputs. Four dampers with fourteen distinct design parameters, installed in pairs along two orthogonal directions, are optimally designed. A genetic algorithm is used to search for the optimum parameter values for the four dampers. This approach is quite versatile as it can be used with different design criteria and definitions of seismic inputs. It usually provides a globally optimum solution. Several optimal design criteria, expressed in terms of performance functions that depend on the structural response, are used. Several sets of numerical results for a torsional system excited by random and response spectrum models of seismic inputs are presented to show the effectiveness of the optimum designs in reducing the system response. Copyright © 2002 John Wiley & Sons, Ltd. 相似文献
16.
This paper deals with the optimal design of yielding metallic dampers and friction dampers together as they both have similar design characteristics and parameters. Ample tests and analytical studies have confirmed the effectiveness of these energy dissipation devices for seismic response control and protection of building structures. Since these devices are strongly non‐linear with several parameters controlling their behaviour, their current design procedures are usually cumbersome and not optimal. In this paper, a methodology is presented to determine the optimal design parameters for the devices installed at different locations in a building for a desired performance objective. For a yielding metallic damper, the design parameters of interest are the device yield level, device stiffness, and brace stiffness. For a friction device, the parameters are the slip load level and brace stiffness. Since the devices and the structures installed with these devices behave in a highly non‐linearly manner, and thus must be evaluated by a step‐by‐step time history approach, the genetic algorithm is used to obtain the globally optimal solution. This optimal search approach allows an unusual flexibility in the choice of performance objectives. For demonstration purposes, several sets of numerical examples of optimal damper designs with different performance objectives are presented. Copyright © 2003 John Wiley & Sons, Ltd. 相似文献
17.
Seismic fragility and reliability of structures isolated by friction pendulum devices: seismic reliability‐based design (SRBD) 下载免费PDF全文
下载免费PDF全文 The paper deals with the seismic reliability of elastic structural systems equipped with friction pendulum isolators (friction pendulum system). The behavior of these systems is analyzed by employing a two‐degree‐of‐freedom model accounting for the superstructure flexibility, whereas the friction pendulum system device behavior is described by adopting a widespread model that considers the variation of the friction coefficient with the velocity. With reference to medium soil condition, the uncertainty in the seismic inputs is taken into account by considering a set of artificial records, obtained through Monte Carlo simulations within the power spectral density method, with different frequency contents and characteristics depending on the soil dynamic parameters and scaled to increasing intensity levels. The sliding friction coefficient at large velocity is also considered as random variable modeled through a uniform probability density function. Incremental dynamic analyses are developed in order to evaluate the probabilities exceeding different limit states related to both r.c. superstructure and isolation level defining the seismic fragility curves through an extensive parametric study carried out for different structural system properties. Finally, considering the seismic hazard curves related to a site near L'Aquila (Italy), the seismic reliability of the r.c. superstructure systems is evaluated, and seismic reliability‐based design abacuses are derived with the aim to define the radius in plan of the friction pendulum devices in function of the structural properties and reliability level expected. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
18.
19.
Probabilistic risk analysis is an effective tool for risk-informed decision-making related to the building facilities. All sources of the uncertainties should be considered in seismic risk assessment framework. Not only the levels of these uncertainties but also the effects on the performance of the buildings should be clearly identified. This paper aims to assess the impacts of the potential uncertainties on the seismic risk of steel frame equipped with steel panel wall (SPWF). Firstly, the performance limits of the SPWF structures are determined according to cyclic test results of two SPWF specimens. Then a validated numerical model of a 12-story SPWF building is modeled and used to perform the nonlinear time-history analysis, and the record-to-record uncertainty is identified by a set of ground motions derived from SAC project. Furthermore, comparisons are made on fragility curves for the building with or without considering the combining uncertainties in structural system, in defining performance limits and modeling technology. Finally, the annual probability and probability in 50 years for each performance limit is calculated and compared. The impacts of such uncertainties on seismic risk of SPWF building are quantified for risk-informed evaluation of the SPWF buildings. 相似文献
20.
摩擦型与软钢屈服型耗能器的性能与减振效果的试验比较 总被引：20，自引：5，他引：20
本文通过两类四种百余个耗能器（其中摩擦类型的两种，普遍摩擦型和Ｐａｌｌ摩擦型；软钢屈服类型的两种：Ｘ钢板和三角钢板屈服型）的静力反复加载和低周疲劳试验，进一步了解这些耗能器的滞回特性和疲劳性能。其次，通过分别安装上述四种耗能器的单层剪切型钢框架模型在输入地震动分别为ＥＩＣｅｎｔｒｏ、Ｔａｆｔ和天津记录等五十余种工况下的振动台试验，较全面地揭示了这些耗能器的减振效果。最后，在试验的基础上较好地建立了 相似文献