首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 31 毫秒
1.
Twin Tsunamis Triggered by the 12 January 2010 Haiti Earthquake   总被引：2，自引：0，他引：2  
On 12 January 2010, a magnitude M w 7.0 earthquake occurred 25 km west–southwest of Haiti’s capital Port-au-Prince causing an estimated 316,000 fatalities, thereby exceeding any previous loss of life from a similar size earthquake. In addition, tsunami waves triggered by the earthquake caused at least three fatalities at Petit Paradis due to a complete lack of tsunami awareness. The International Tsunami Survey Team (ITST) was deployed within weeks of the event and covered the greater Bay of Port-au-Prince and more than 100 km of Hispaniola’s southern coastline. The collected survey data include more than 21 tsunami heights along with observations of coastal land level change. Maximum tsunami heights of 3 m have been measured for two independently triggered tsunamis.  相似文献   

2.
—Whereas the coast of Peru south of 10°S is historically accustomed to tsunamigenic earthquakes, the subduction zone north of 10°S has been relatively quiet. On 21 February 1996 at 21:51 GMT (07:51 local time) a large, tsunamigenic earthquake (Harvard estimate M w = 7.5) struck at 9.6°S, 79.6°W, approximately 130 km off the northern coast of Peru, north of the intersection of the Mendaña fracture zone with the Peru–Chile trench. The likely mechanism inferred from seismic data is a low-angle thrust consistent with subduction of the Nazca Plate beneath the South American plate, with relatively slow rupture characteristics. Approximately one hour after the main shock, a damaging tsunami reached the Peruvian coast, resulting in twelve deaths. We report survey measurements, from 7.7°S to 11°S, on maximum runup (2–5m, between 8 and 10°S), maximum inundation distances, which exceeded 500 m, and tsunami sediment deposition patterns. Observations and numerical simulations show that the hydrodynamic characteristics of this event resemble those of the 1992 Nicaragua tsunami. Differences in climate, vegetation and population make these two tsunamis seem more different than they were. This 1996 Chimbote event was the first large (M w >7) subduction-zone (interplate) earthquake between about 8 and 10°S, in Peru, since the 17th century, and bears resemblance to the 1960 (M w 7.6) event at 6.8°S. Together these two events are apparently the only large subduction-zone earthquakes in northern Peru since 1619 (est. latitude 8°S, est. M w 7.8); these two tsunamis also each produced more fatalities than any other tsunami in Peru since the 18th century. We concur with Pelayo and Wiens (1990, 1992) that this subduction zone, in northern Peru, resembles others where the subduction zone is only weakly coupled, and convergence is largely aseismic. Subduction-zone earthquakes, when they occur, are slow, commonly shallow, and originate far from shore (near the tip of the wedge). Thus they are weakly felt, and the ensuing tsunamis are unanticipated by local populations. Although perhaps a borderline case, the Chimbote tsunami clearly is another wake-up example of a "tsunami earthquake."  相似文献   

3.
Following the 2007, August 15th, M w 8.0, Pisco earthquake in central Peru, Sladen et al. (J Geophys Res 115: B02405, 2010) have derived several slip models of this event. They inverted teleseismic data together with geodetic (InSAR) measurements to look for the co-seismic slip distribution on the fault plane, considering those data sets separately or jointly. But how close to the real slip distribution are those inverted slip models? To answer this crucial question, the authors generated some tsunami records based on their slip models and compared them to DART buoys, tsunami records, and available runup data. Such an approach requires a robust and accurate tsunami model (non-linear, dispersive, accurate bathymetry and topography, etc.) otherwise the differences between the data and the model may be attributed to the slip models themselves, though they arise from an incomplete tsunami simulation. The accuracy of a numerical tsunami simulation strongly depends, among others, on two important constraints: (i) A fine computational grid (and thus the bathymetry and topography data sets used) which is not always available, unfortunately, and (ii) a realistic tsunami propagation model including dispersion. Here, we extend Sladen’s work using newly available data, namely a tide gauge record at Callao (Lima harbor) and the Chilean DART buoy record, while considering a complete set of runup data along with a more realistic tsunami numerical that accounts for dispersion, and also considering a fine-resolution computational grid, which is essential. Through these accurate numerical simulations we infer that the InSAR-based model is in better agreement with the tsunami data, studying the case of the Pisco earthquake indicating that geodetic data seems essential to recover the final co-seismic slip distribution on the rupture plane. Slip models based on teleseismic data are unable to describe the observed tsunami, suggesting that a significant amount of co-seismic slip may have been aseismic. Finally, we compute the runup distribution along the central part of the Peruvian coast to better understand the wave amplification/attenuation processes of the tsunami generated by the Pisco earthquake.  相似文献   

4.
The M w = 9.0 earthquake that occurred off the coast of Japan’s Tohoku region produced a great tsunami causing catastrophic damage and loss of life. Within hours of the tsunami event, satellite data were readily available and massive media coverage immediately circulated thousands of photographs and videos of the tsunami. Satellite data allow a rapid assessment of inundated areas where access can be difficult either as a result of damaged infrastructure (e.g., roads, bridges, ports, airports) or because of safety issues (e.g., the hazard at Nuclear Power Plant at Fukushima). In this study, we assessed in a day tsunami inundation distances and runup heights using satellite data (very high-resolution satellite images from the GeoEye1 satellite and from the DigitalGlobe worldview, SRTM and ASTER GDEM) of the Tohoku region, Northeast Japan. Field survey data by Japanese and other international scientists validated our results. This study focused on three different locations. Site selection was based on coastal morphologies and the distance to the tsunami source (epicenter). Study sites are Rikuzentakata, Oyagawahama, and Yagawahama in the Oshika Peninsula, and the Sendai coastal plain (Sendai City to Yamamoto City). Maximum inundation distance (6 km along the river) and maximum runup (39 m) at Rikuzentakata estimated from satellite data agree closely with the 39.7 m inundation reported in the field. Here the ria coastal morphology and horn shaped bay enhanced the tsunami runup and effects. The Sendai coastal plain shows large inundation distances (6 km) and lower runup heights. Natori City and Wakabayashi Ward, on the Sendai plain, have similar runup values (12 and 16 m, respectively) obtained from SRTM data; these are comparable to those obtained from field surveys (12 and 9.5 m). However, at Yagawahama and Oyagawahama, Miyagi Prefecture, both SRTM and ASTER data provided maximum runup heights (41 to 45 m and 33 to 34 m, respectively), which are higher than those measured in the field (about 27 m). This difference in DEM and field data is associated with ASTER and SRTM DEM’s pixel size and vertical accuracy, the latter being dependent on ground coverage, slope, aspect and elevation. Countries with less access to technology and infrastructure can benefit from the use of satellite imagery and freely available DEMs for an initial, pre-field surveys, rapid estimate of inundated areas, distances and runup, and for assisting in hazard management and mitigation after a natural disaster.  相似文献   

5.
The major (M w = 8.8) Chilean earthquake of 27 February 2010 generated a trans-oceanic tsunami that was observed throughout the Pacific Ocean. Waves associated with this event had features similar to those of the 1960 tsunami generated in the same region by the Great (M w = 9.5) 1960 Chilean Earthquake. Both tsunamis were clearly observed on the coast of British Columbia. The 1960 tsunami was measured by 17 analog pen-and-paper tide gauges, while the 2010 tsunami was measured by 11 modern digital coastal tide gauges, four NEPTUNE-Canada bottom pressure recorders located offshore from southern Vancouver Island, and two nearby open-ocean DART stations. The 2010 records were augmented by data from seven NOAA tide gauges on the coast of Washington State. This study examines the principal characteristics of the waves from the 2010 event (height, period, duration, and arrival and travel times) and compares these properties for the west coast of Canada with corresponding properties of the 1960 tsunami. Results show that the 2010 waves were approximately 3.5 times smaller than the 1960 waves and reached the British Columbia coast 1 h earlier. The maximum 2010 wave heights were observed at Port Alberni (98.4 cm) and Winter Harbour (68.3 cm); the observed periods ranged from 12 min at Port Hardy to 110–120 min at Prince Rupert and Port Alberni and 150 min at Bamfield. The open-ocean records had maximum wave heights of 6–11 cm and typical periods of 7 and 15 min. Coastal and open-ocean tsunami records revealed persistent oscillations that “rang” for 3–4 days. Tsunami energy occupied a broad band of periods from 3 to 300 min. Estimation of the inverse celerity vectors from cross-correlation analysis of the deep-sea tsunami records shows that the tsunami waves underwent refraction as they approached the coast of Vancouver Island with the direction of the incoming waves changing from an initial direction of 340° True to a direction of 15° True for the second train of waves that arrived 7 h later after possible reflection from the Marquesas and Hawaiian islands.  相似文献   

6.
The near-field expression of the tsunami produced by the 15 November 2006 Kuril earthquake (Mw 8.1–8.4) in the middle Kuril Islands, Russia, including runup of up to 20 m, remained unknown until we conducted a post-tsunami survey in the summer of 2007. Because the earthquake occurred between summer field expeditions in 2006 and 2007, we have observations, topographic profiles, and photographs from three months before and nine months after the tsunami. We thoroughly surveyed portions of the islands of Simushir and Matua, and also did surveys on parts of Ketoi, Yankicha, Ryponkicha, and Rasshua. Tsunami runup in the near-field of the middle Kuril Islands, over a distance of about 200 km, averaged 10 m over 130 locations surveyed and was typically between 5 and 15 m. Local topography strongly affected inundation and somewhat affected runup. Higher runup generally occurred along steep, protruding headlands, whereas longer inundation distances occurred on lower, flatter coastal plains. Sediment transport was ubiquitous where sediment was available—deposit grain size was typically sand, but ranged from mud to large boulders. Wherever there were sandy beaches, a more or less continuous sand sheet was present on the coastal plain. Erosion was extensive, often more extensive than deposition in both space and volume, especially in areas with runup of more than 10 m. The tsunami eroded the beach landward, stripped vegetation, created scours and trim lines, cut through ridges, and plucked rocks out of the coastal plain.  相似文献   

7.
We calculated tsunami runup probability (in excess of 0.5 m) at coastal sites throughout the Caribbean region. We applied a Poissonian probability model because of the variety of uncorrelated tsunami sources in the region. Coastlines were discretized into 20 km by 20 km cells, and the mean tsunami runup rate was determined for each cell. The remarkable ~500-year empirical record compiled by O’Loughlin and Lander (2003) was used to calculate an empirical tsunami probability map, the first of three constructed for this study. However, it is unclear whether the 500-year record is complete, so we conducted a seismic moment-balance exercise using a finite-element model of the Caribbean-North American plate boundaries and the earthquake catalog, and found that moment could be balanced if the seismic coupling coefficient is c = 0.32. Modeled moment release was therefore used to generate synthetic earthquake sequences to calculate 50 tsunami runup scenarios for 500-year periods. We made a second probability map from numerically-calculated runup rates in each cell. Differences between the first two probability maps based on empirical and numerical-modeled rates suggest that each captured different aspects of tsunami generation; the empirical model may be deficient in primary plate-boundary events, whereas numerical model rates lack backarc fault and landslide sources. We thus prepared a third probability map using Bayesian likelihood functions derived from the empirical and numerical rate models and their attendant uncertainty to weight a range of rates at each 20 km by 20 km coastal cell. Our best-estimate map gives a range of 30-year runup probability from 0–30% regionally.  相似文献   

8.
On December 12, 1992 a large earthquake (M s 7.5) occurred just north of Flores Island, Indonesia which, along with the tsunami it generated, killed more than 2,000 people. In this study, teleseismicP andSH waves, as well asPP waves from distances up to 123°, are inverted for the orientations and time histories of multiple point sources. By repeating the inversion for reasonable values of depth, time separation and spatial separation, a 2-fault model is developed. Next, the vertical deformation of the seafloor is estimated from this fault model. Using a detailed bathymetric model, linear and nonlinear tsunami propagation models are tested. The data consist of a single tide gauge record at Palopo (650 km to the north), as well as tsunami runup height measurements from Flores Island and nearby islands. Assuming a tsunami runup amplification factor of two, the two-fault model explains the tide gauge record and the tsunami runup heights on most of Flores Island. It cannot, however, explain the large tsunami runup heights observed near Leworahang (on Hading Bay) and Riangkroko (on the northeast peninsula). Massive coastal slumping was observed at both of these locations. A final model, which in addition to the two faults, includes point sources of large vertical displacement at these two locations explains the observations quite well.  相似文献   

9.
Anomalous earthquakes such as creep events, tsunami earthquakes and silent earthquakes have been reported in the recent literature. In this paper we discuss an anomalous “slow earthquake” that occurred on June 6, 1960 in southern Chile. Although the surface-wave magnitude of this event is only 6.9, it excited anomalously large long-period multiple surface waves with a seismic moment of 5.6 · 1027 dyn cm. The Benioff long-period seismogram of this earthquake recorded at Pasadena shows an extremely long, about 1.5–2 h coda of Rayleigh waves, with a period of 10–25 s. The coda length for other events with a comparable magnitude which occurred in the same region is about 10 min. This observation suggests that the long coda length is due to a long source rupture process which lasted at least 1 h. Although at least 15 distinct events can be identified in the coda, no short-period body waves were recorded corresponding to these, except for the first one. These results suggest that a relatively small (Ms ? 6.9) earthquake triggered a series of slow events; the duration of the whole sequence being longer than 1 h. This event probably occurred on a transform fault on the extension of the Chile Rise and provides important information regarding the nature of the transform fault.  相似文献   

10.
The slip distribution and seismic moment of the 2010 and 1960 Chilean earthquakes were estimated from tsunami and coastal geodetic data. These two earthquakes generated transoceanic tsunamis, and the waveforms were recorded around the Pacific Ocean. In addition, coseismic coastal uplift and subsidence were measured around the source areas. For the 27 February 2010 Maule earthquake, inversion of the tsunami waveforms recorded at nearby coastal tide gauge and Deep Ocean Assessment and Reporting of Tsunamis (DART) stations combined with coastal geodetic data suggest two asperities: a northern one beneath the coast of Constitucion and a southern one around the Arauco Peninsula. The total fault length is approximately 400 km with seismic moment of 1.7 × 1022 Nm (Mw 8.8). The offshore DART tsunami waveforms require fault slips beneath the coasts, but the exact locations are better estimated by coastal geodetic data. The 22 May 1960 earthquake produced very large, ~30 m, slip off Valdivia. Joint inversion of tsunami waveforms, at tide gauge stations in South America, with coastal geodetic and leveling data shows total fault length of ~800 km and seismic moment of 7.2 × 1022 Nm (Mw 9.2). The seismic moment estimated from tsunami or joint inversion is similar to previous estimates from geodetic data, but much smaller than the results from seismic data analysis.  相似文献   

11.
On 11 March 2011, a moment magnitude M w = 9.0 earthquake occurred off the Japan Tohoku coast causing catastrophic damage and loss of human lives. In the immediate aftermath of the earthquake, we conducted the reconnaissance survey in the city of Rikuzentakata, Japan. In comparison with three previous historical tsunamis impacting the same region, the 2011 event presented the largest values with respect to the tsunami height, the inundation area and the inundation distance. A representative tsunami height of 15 m was recorded in Rikuzentakata, with increased heights of 20 m around rocky headlands. In terms of the inundation area, the 2011 Tohoku tsunami exceeded by almost 2.6 times the area flooded by the 1960 Chilean tsunami, which ranks second among the four events compared. The maximum tsunami inundation distance was 8.1 km along the Kesen River, exceeding the 1933 Showa and 1960 Chilean tsunami inundations by factors of 6.2 and 2.7, respectively. The overland tsunami inundation distance was less than 2 km. The tsunami inundation height linearly decreased along the Kesen River at a rate of approximately 1 m/km. Nevertheless, the measured inland tsunami heights exhibit significant variations on local and regional scales. A designated “tsunami control forest” planted with a cross-shore width of about 200 m along a 2 km stretch of Rikuzentakata coastline was completely overrun and failed to protect the local community during this extreme event. Similarly, many designated tsunami shelters were too low and were overwashed by tsunami waves, thereby failing to provide shelter for evacuees—a risk that had been underestimated.  相似文献   

12.
We apply a recently developed and validated numerical model of tsunami propagation and runup to study the inundation of Resurrection Bay and the town of Seward by the 1964 Alaska tsunami. Seward was hit by both tectonic and landslide-generated tsunami waves during the $M_{\rm W}$ 9.2 1964 megathrust earthquake. The earthquake triggered a series of submarine mass failures around the fjord, which resulted in landsliding of part of the coastline into the water, along with the loss of the port facilities. These submarine mass failures generated local waves in the bay within 5?min of the beginning of strong ground motion. Recent studies estimate the total volume of underwater slide material that moved in Resurrection Bay to be about 211?million m3 (Haeussler et?al. in Submarine mass movements and their consequences, pp 269?C278, 2007). The first tectonic tsunami wave arrived in Resurrection Bay about 30?min after the main shock and was about the same height as the local landslide-generated waves. Our previous numerical study, which focused only on the local landslide-generated waves in Resurrection Bay, demonstrated that they were produced by a number of different slope failures, and estimated relative contributions of different submarine slide complexes into tsunami amplitudes (Suleimani et?al. in Pure Appl Geophys 166:131?C152, 2009). This work extends the previous study by calculating tsunami inundation in Resurrection Bay caused by the combined impact of landslide-generated waves and the tectonic tsunami, and comparing the composite inundation area with observations. To simulate landslide tsunami runup in Seward, we use a viscous slide model of Jiang and LeBlond (J Phys Oceanogr 24(3):559?C572, 1994) coupled with nonlinear shallow water equations. The input data set includes a high resolution multibeam bathymetry and LIDAR topography grid of Resurrection Bay, and an initial thickness of slide material based on pre- and post-earthquake bathymetry difference maps. For simulation of tectonic tsunami runup, we derive the 1964 coseismic deformations from detailed slip distribution in the rupture area, and use them as an initial condition for propagation of the tectonic tsunami. The numerical model employs nonlinear shallow water equations formulated for depth-averaged water fluxes, and calculates a temporal position of the shoreline using a free-surface moving boundary algorithm. We find that the calculated tsunami runup in Seward caused first by local submarine landslide-generated waves, and later by a tectonic tsunami, is in good agreement with observations of the inundation zone. The analysis of inundation caused by two different tsunami sources improves our understanding of their relative contributions, and supports tsunami risk mitigation in south-central Alaska. The record of the 1964 earthquake, tsunami, and submarine landslides, combined with the high-resolution topography and bathymetry of Resurrection Bay make it an ideal location for studying tectonic tsunamis in coastal regions susceptible to underwater landslides.  相似文献   

13.
A numerical model of the wave dynamics in Chenega Cove, Alaska during the historic M w 9.2 megathrust earthquake is presented. During the earthquake, locally generated waves of unknown origin were identified at the village of Chenega, located in the western part of Prince William Sound. The waves appeared shortly after the shaking began and swept away most of the buildings while the shaking continued. We model the tectonic tsunami in Chenega Cove assuming different tsunami generation processes. Modeled results are compared with eyewitness reports and an observed runup. Results of the numerical experiments let us claim the importance of including both vertical and horizontal displacement into the 1964 tsunami generation process. We also present an explanation for the fact that arrivals of later waves in Chenega were unnoticed.  相似文献   

14.
In the hours following the 2011 Honshu event, and as part of tsunami warning procedures at the Laboratoire de Géophysique in Papeete, Tahiti, the seismic source of the event was analyzed using a number of real-time procedures. The ultra-long period mantle magnitude algorithm suggests a static moment of 4.1 × 1029 dyn cm, not significantly different from the National Earthquake Information Center (NEIC) value obtained by W-phase inversion. The slowness parameter, $\Uptheta = -5.65, $ is slightly deficient, but characteristic of other large subduction events such as Nias (2005) or Peru (2001); it remains significantly larger than for slow earthquakes such as Sumatra (2004) or Mentawai (2010). Similarly, the duration of high-frequency (2–4 Hz) P waves in relation to seismic moment or estimated energy, fails to document any slowness in the seismic source. These results were confirmed in the ensuing weeks by the analysis of the lowest-frequency spheroidal modes of the Earth. A dataset of 117 fits for eight modes (including the gravest one, 0 S 2, and the breathing mode, 0 S 0) yields a remarkably flat spectrum, with an average moment of 3.5 × 1029 dyn cm (*/1.07). This behavior of the Tohoku earthquake explains the generally successful real-time modeling of its teleseismic tsunami, based on available seismic source scaling laws. On the other hand, it confirms the dichotomy, among mega-quakes (M 0 > 1029 dyn cm) between regular events (Nias, 2005; Chile, 2010; Sendai, 2011) and slow ones (Chile, 1960; Alaska, 1964; Sumatra, 2004; and probably Rat Island, 1965), whose origin remains unexplained.  相似文献   

15.
On November 15, 2006, Crescent City in Del Norte County, California was hit by a tsunami generated by a M w 8.3 earthquake in the central Kuril Islands. Strong currents that persisted over an eight-hour period damaged floating docks and several boats and caused an estimated $9.2 million in losses. Initial tsunami alert bulletins issued by the West Coast Alaska Tsunami Warning Center (WCATWC) in Palmer, Alaska were cancelled about three and a half hours after the earthquake, nearly five hours before the first surges reached Crescent City. The largest amplitude wave, 1.76-meter peak to trough, was the sixth cycle and arrived over two hours after the first wave. Strong currents estimated at over 10 knots, damaged or destroyed three docks and caused cracks in most of the remaining docks. As a result of the November 15 event, WCATWC changed the definition of Advisory from a region-wide alert bulletin meaning that a potential tsunami is 6 hours or further away to a localized alert that tsunami water heights may approach warning- level thresholds in specific, vulnerable locations like Crescent City. On January 13, 2007 a similar Kuril event occurred and hourly conferences between the warning center and regional weather forecasts were held with a considerable improvement in the flow of information to local coastal jurisdictions. The event highlighted the vulnerability of harbors from a relatively modest tsunami and underscored the need to improve public education regarding the duration of the tsunami hazards, improve dialog between tsunami warning centers and local jurisdictions, and better understand the currents produced by tsunamis in harbors.  相似文献   

16.
On the evening of March 28, 2005 at 11:09?p.m. local time (16:09 UTC), a large earthquake occurred offshore of West Sumatra, Indonesia. With a moment magnitude (M w) of 8.6, the event caused substantial shaking damage and land level changes between Simeulue Island in the north and the Batu Islands in the south. The earthquake also generated a tsunami, which was observed throughout the source region as well as on distant tide gauges. While the tsunami was not as extreme as the tsunami of December 26th, 2004, it did cause significant flooding and damage at some locations. The spatial and temporal proximity of the two events led to a unique set of observational data from the earthquake and tsunami as well as insights relevant to tsunami hazard planning and education efforts.  相似文献   

17.
The 2010 Mentawai earthquake (magnitude 7.7) generated a destructive tsunami that caused more than 500 casualties in the Mentawai Islands, west of Sumatra, Indonesia. Seismological analyses indicate that this earthquake was an unusual “tsunami earthquake,” which produces much larger tsunamis than expected from the seismic magnitude. We carried out a field survey to measure tsunami heights and inundation distances, an inversion of tsunami waveforms to estimate the slip distribution on the fault, and inundation modeling to compare the measured and simulated tsunami heights. The measured tsunami heights at eight locations on the west coasts of North and South Pagai Island ranged from 2.5 to 9.3 m, but were mostly in the 4–7 m range. At three villages, the tsunami inundation extended more than 300 m. Interviews of local residents indicated that the earthquake ground shaking was less intense than during previous large earthquakes and did not cause any damage. Inversion of tsunami waveforms recorded at nine coastal tide gauges, a nearby GPS buoy, and a DART station indicated a large slip (maximum 6.1 m) on a shallower part of the fault near the trench axis, a distribution similar to other tsunami earthquakes. The total seismic moment estimated from tsunami waveform inversion was 1.0 × 1021 Nm, which corresponded to Mw 7.9. Computed coastal tsunami heights from this tsunami source model using linear equations are similar to the measured tsunami heights. The inundation heights computed by using detailed bathymetry and topography data and nonlinear equations including inundation were smaller than the measured ones. This may have been partly due to the limited resolution and accuracy of publically available bathymetry and topography data. One-dimensional run-up computations using our surveyed topography profiles showed that the computed heights were roughly similar to the measured ones.  相似文献   

18.
—The 1996 subaquatic explosive eruption near the northern shore of Karymskoye Lake in Kamchatka, Russia, generated multiple tsunamis. We document the explosive process that produced the tsunamis, and describe the tsunami effects and runup around the 4-km diameter lake. These data enable the determination of an attenuation relation of runup (wave) height for these “explosive” tsunamis, which is compared with theoretical models of wave height distributions. For the proximal zone, involving radial distances (r) up to 1.3 km from the source, the runup height (R) shows rapid attenuation (from > 30 m to 8 m) with distance as log R = ?1.98 log[r] + 2.6. For the distal zone, r > 1.3 km, involving mainly wave travel southeastwards along the body of the lake away from the explosion source, R decays more slowly (from 8 m to 3 m) as log R = ?0.56 log[r] + 1.9. Rapid decay in the proximal zone suggests that near the source of the explosion, the tsunami propagated radially as a collapsing wave (bore) with discontinuous change in height. The break-in-slope of the runup plot at 1.3 km suggests that beyond this distance the tsunami propagated approximately as a decaying one-dimensional wave in a channel of approximately constant width.  相似文献   

19.
Eighteen papers on past and recent destructive tsunamis are included in Volume II of the PAGEOPH topical issue “Historical and Recent Catastrophic Tsunamis in the World.” Three papers discuss deep-sea (DART) and coastal tsunami observations, warning systems and risk management in the Pacific Ocean. Four papers examine the 1755 Lisbon, 1964 Alaska, 2003 Algeria, and 2011 Haiti tsunamis. Four more papers, as well as some papers in Volume I, report on various aspects of the 2010 Chile tsunami. Two papers present some results of field survey and modelling investigation of the 2010 Mentawai, Indonesia, tsunami. Three papers report on modelling efforts of tsunami generation by earthquake and landslide, and of tsunami propagation. Finally, two papers discuss hazard assessment using a probabilistic approach.  相似文献   

20.
The most recent high magnitude seismic events, e.g. the Mw 8.2 Iquique earthquake (April 1st, 2014) and the Mw 8.8 Maule earthquake (February 27th, 2010) are reminders of the pronounced vulnerability of the Chilean coast to the impact of natural hazards like earthquakes and tsunamis. Therefore it is crucial to understand the complex tsunami history of Chile which can be deciphered by studying the geological record of former tsunamis in the form of tsunami deposits.At the coastal locality of Tirúa (Central Chile) six distinct, successive tsunamigenic sand layers are intercalated in fine grained floodplain sediments. We present the optically stimulated luminescence (OSL) analysis of quartz from samples of this sedimentological river marsh profile of 1.5 m depth.After the assessment of the applicability of OSL to these samples, it could be noted that despite of an expected low OSL sensitivity of the quartz from the South American Cordillera, most of the sampled quartz yielded a detectable natural signal. After performance tests according to the SAR-protocol, the measurements of the different tsunami sand layers were conducted with small (2.5 mm) aliquots of quartz with the preheat temperature 180 °C. The calculation of De was provided by applying both the central age and minimum age models. All samples are heterogeneous in their De distributions due to incomplete or absent significant bleaching during transport by tsunami. The resulting ages of the tsunami sediments yield an offset of nearly 200 years for CAM ages and less than 50 years for MAM ages, consequently favouring MAM ages for true burial age determination. In some tsunami sand layers and their surrounding river marsh sediments age inversions occur. They were caused by the initial deposition of well bleached sediments derived from beach and dunes followed by older sediments redeposited from beach and intertidal environments during tsunami flow. Despite the offset and age inversion six different tsunami events were dated in the Tirúa profile. Three of these events extend the historical record to pre-Columbian time with the oldest tsunami dated to over 1500 years before present.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号