共查询到18条相似文献，搜索用时 140 毫秒
1.
框架剪力墙结构模态静力非线性抗震分析方法研究 总被引：5，自引：2，他引：3
本文在模态pushover分析方法基础上推导建立了模态静力非线性分析方法,对一栋10层框架剪力墙结构进行了静力非线性分析,提出了目标位移求解的等效单自由度体系弹塑性时程分析迭代法,计算结果与相应时程分析结果进行了比较,表明两者吻合较好,验证了本文计算方法的有效性。另外,对同一结构,计算分析了在不同水平荷载模式下的静力非线性分析结果,比较不同荷载模式对计算结果的影响,为静力非线性分析方法的推广使用提供参考。 相似文献
2.
基于位移的结构静力弹塑性分析方法的研究 总被引：7，自引：0，他引：7
本文系统介绍了基于位移的一般结构静力弹塑性(pushover)分析方法、自适应结构静力弹塑性(pushover)分析方法,指出了基于力的结构静力弹塑性(pushover)分析方法与基于位移的结构静力弹塑性(pushover)分析方法的差别。应用各种结构静力弹塑性(pushover)分析方法对一7层和15层框架剪力墙结构进行了计算与比较分析。算例结果表明,应用基于位移的一般结构静力弹塑性(push-over)分析方法对结构的抗震性能进行评估时,不受高阶振型的影响,结果更加准确合理。 相似文献
3.
4.
为了建立统一的动力响应分析模型,本文以NUPEC振动台试验的H形断面钢筋混凝土立体剪力墙为研究对象进行了三维非线性有限元动力响应分析。根据分析结果与试验结果的比较可知,在RC剪力墙到达最大承载力之前由简化模型和一般模型得到的动力响应特性与试验结果吻合较好,荷载-变形关系能很好模拟试验结果。但是,最大承载力之后,由于混凝土开裂、损伤、劣化的急剧发展,较难模拟混凝土开裂、裂缝的开闭及滑移等非线性特性,分析得到的加速度衰减较慢、位移响应较小。基于上述研究成果探讨并提出了进一步改善非线性有限元动力响应分析精度的建议。 相似文献
5.
《地震工程与工程振动》2021,41(3)
为研究复式钢管混凝土钢板剪力墙框架的抗震力学性能,基于装配式复式钢管混凝土柱-钢板剪力墙框架结构拟静力试验研究,合理采用材料本构关系并引入了损伤因子来考虑混凝土的损伤退化,利用ABAQUS软件建立两榀框架的有限元模型,并且对结构进行有限元计算。有限元模拟所得框架的滞回曲线与试验所得吻合良好,验证了有限元模拟的正确性。基于此,分析了整体框架以及各构件在受力过程中的应力分布,验证了钢板对于该类结构抗震性能有明显的提升及结构试件设计的合理性;最后对该类框架结构进行了参数分析,研究了轴压比、钢材强度及钢板剪力墙厚度对结构抗震性能的影响,为此类框架结构试验以及工程应用提供参考。 相似文献
6.
有横缝拱坝的非线性动力模型试验和计算分析研究 总被引：12，自引：0，他引：12
本文通过在大型三向地震模拟振动台上进行的设置伸缩横缝的某拱坝非线性动力模型试验，应用非线性有限元动力分析程序同时进行计算分析，全面系统地研究了拱坝横缝对坝体动力特性和地震反应的影响，并对计算程序进行了改进。试验与计算结果相互印证，验证了试验成果的可靠性和计算分析模型、计算程序与计算结果的合理性。 相似文献
7.
性态抗震设计已成为结构抗震设计的发展趋势,本文以约束混凝土砌块结构为对象,在提出约束混凝土砌块墙承载力计算公式的基础上,建立了砌块墙片的恢复力模型。对3座不同层数的典型约束混凝土砌块结构,在代表不同场地类别、不同地震动强度的输入下分别进行了动力非线性时程分析和静力非线性分析。通过计算结果的对比,讨论了2种分析方法中场地类别、地震动强度、静力非线性分析中侧力分布模式等影响,所得结论可以为用静力非线性分析估计砌块结构的抗震性能提供有益的参考依据。 相似文献
8.
新型钢板剪力墙钢框架结构的地震响应分析 总被引：5，自引：2，他引：3
本文在单片带缝钢板剪力墙理论研究的基础上,提出带缝钢板剪力墙的等效计算模型,对钢板剪力墙钢框架结构工程实例结构进行自振特性分析、常遇地震作用下的动力响应分析以及结构在罕遇地震作用下的三维非线性时程响应分析,得到一些有意义的结果和结论。 相似文献
9.
轻钢骨混凝土剪力墙延性的非线性有限元分析 总被引：3，自引：1，他引：2
轻钢骨混凝土剪力墙结构作为新型结构在工程界要得到认同并推广使用,必须对该结构的各项性能指标进行系统的试验研究和理论分析。本文应用ADINA有限元软件对轻钢骨混凝土剪力墙延性进行非线性有限元分析,根据不同的高宽比、轴压比、轻钢骨配筋率以及端部配筋模型的计算结果,对该结构体系的延性及其破坏形态进行综合分析,并对轻钢骨混凝土剪力墙轴压比设计提出建议。分析结果表明,高宽比主要控制轻钢骨混凝土剪力墙的破坏形态,轴压比对其结构的延性的影响最为显著,而端部配筋对其延性影响不大。 相似文献
10.
基础隔震高层建筑地震响应的理论分析 总被引：4，自引：2，他引：4
本文对某高层隔震框架－剪力墙结构的三维地震响应进行了有限元分析计算，对比了隔震结构及其相应非隔震结构的动力特性，给出了在多遇地震和罕遇地震作用下结构的最大层间剪力，层间位移等，得到一些有意义的结论。 相似文献
11.
Finite element analysis of damage and failure of reinforced concrete members under earthquake loading 
下载免费PDF全文
下载免费PDF全文 This paper presents a three‐dimensional analysis framework, based on the explicit finite element method, for the simulation of reinforced concrete components under cyclic static and dynamic loading. A recently developed triaxial constitutive model for concrete is combined with a material model for reinforcing steel which can account for rupture due to low‐cycle fatigue. The reinforcing bars are represented with geometrically nonlinear beam elements to account for buckling of the reinforcement. The strain penetration effect is also accounted for in the models. The modeling scheme is used in a commercial finite element program and validated with the results of experimental static and dynamic tests on reinforced concrete columns and walls. The analyses are supplemented with a parametric study to investigate the impact of several modeling assumptions on the obtained results. 相似文献
12.
为适应高强材料在土木工程结构中的应用发展需要,本文研究高强混凝土剪力墙在不同参数影响下的受力状态、应力分布以及承载力的变化规律,为高强混凝土剪力墙设计提出合理建议.利用有限元分析软件对高强混凝土剪力墙进行模拟分析,并将模拟结果与试验结果进行对比.在确定数值分析结果的正确性后,进行不同轴压比、剪跨比及不同配筋条件下该类构件数值模拟分析,以研究各参数对高强混凝土剪力墙延性的影响.明确各参数对高强混凝土剪力墙受力性能的影响效果,得出高强混凝土剪力墙承载力随各参数变化的规律. 相似文献
13.
This paper presents three-dimensional fi nite element (FE) analyses of an all-frame model of a three-story reinforced concrete (RC) building damaged in the 1999 Taiwan Chi-Chi Earthquake. Non-structural brick walls of the building acted as a seismic resistant element although their contributions were neglected in the design. Hence, the entire structure of a typical frame was modeled and static and dynamic nonlinear analyses were conducted to evaluate the contributions of the brick walls. However, the results of the analyses were considerably overestimated due to coarse mesh discretizations, which were unavoidable due to limited computer resources. This study corrects the overestimations by modifying (1) the tensile strengths and (2) shear stiffness reduction factors of concrete and brick. The results indicate that brick walls improve frame strength although shear failures are caused in columns shortened by spandrel walls. Then, the effectiveness of three types of seismic retrofi ts is evaluated. The maximum drift of the firstoor is reduced by 89.3%, 94.8%, and 27.5% by Steel-confi ned, Full-RC, and Full-brick models, respectively. Finally, feasibility analyses of models with soils were conducted. The analyses indicated that the soils elongate the natural period of building models although no signifi cant differences were observed. 相似文献
14.
基于柔度法的异形截面钢筋混凝土构件非线性分析 总被引：2，自引：0，他引：2
钢筋混凝土异形截面构件在住宅建筑中已被广泛应用,但适合此类长细比较小的异形截面构件空间分析模型并不成熟.目前国内外学者提出的基于有限单元柔度法的纤维单元模型,还不能考虑剪切变形对构件刚度的影响,对于短肢剪力墙这类长细比较小的构件是不适用的.本文建立了考虑剪切变形的基于柔度法的弹塑性纤维单元,对L形钢筋混凝土构件进行了算例分析.模拟计算结果与试验结果显示出良好的一致性,L形截面构件在侧力作用下会发生斜弯曲现象,钢筋混凝土构件在纯弯矩作用下杆件具有伸长特性. 相似文献
15.
16.
Assessment of the dynamic response of unreinforced masonry structures using a macroelement modeling approach 下载免费PDF全文
下载免费PDF全文 César Chácara Francesco Cannizzaro Bartolomeo Pantò Ivo Caliò Paulo B. Lourenço 《地震工程与结构动力学》2018,47(12):2426-2446
The seismic performance of unreinforced masonry structures is strongly associated with the interaction between in‐plane and out‐of‐plane mechanisms. The seismic response of these structures has been thoroughly investigated by means of experimental testing, analytical procedures, and computational approaches. Within the framework of the numerical simulations, models based on the finite element method provide a good prediction of the seismic performance of unreinforced masonry structures. However, they usually require a high computational cost and advanced user expertise to define appropriate mechanical properties and to interpret the numerical results. Because of these limitations, simplified models for practical applications have been developed during the last decades. Despite this, a great number of these models focus mostly on the evaluation of the in‐plane response, assuming box (or integral) behavior of the structure. In this paper, a simplified macroelement modeling approach is used to simulate the seismic response of 2 masonry prototypes taking into consideration the combined in‐plane and out‐of‐plane action. The numerical investigations were performed in the static and dynamic fields by using pushover analyses and nonlinear dynamic analyses respectively. The latter is a novel implementation of a model previously developed for static analysis. The results obtained from this study are in good agreement with those provided by a detailed nonlinear continuum FE approach, demonstrating the applicability of this macroelement model with a significant reduction of the computational cost. 相似文献
17.
运用ABAQUS分析软件,建立水平荷载作用下的钢筋混凝土核心筒有限元模型,进行非线性分析,并将分析结果与大比例试件的试验结果对比,对所采用的有限元模型加以验证。在此基础上,进行改变钢筋混凝土核心筒轴压比、高宽比和筒壁厚度的受力过程模拟分析,研究这些参数对筒体性能的影响。结果表明：随着轴压比的增大,筒体的破坏由受拉向受压破坏转变,筒体最大水平承载力经历先增加后减小的变化,延性变差;随着高宽比的增大,筒体破坏形态由剪切向弯曲破坏转变,延性增加,整体弯曲作用更加明显,最大底部剪力减小;随着壁厚的增大,试件破坏由截面压屈失稳向墙肢底部受弯破坏转变,墙肢破坏区域沿高度方向发展,耗能能力更强,承载力明显增大,变形能力显著增加。 相似文献
18.
Since most current seismic capacity evaluations of reinforced concrete(RC) frame structures are implemented by either static pushover analysis(PA) or dynamic time history analysis,with diverse settings of the plastic hinges(PHs) on such main structural components as columns,beams and walls,the complex behavior of shear failure at beam-column joints(BCJs) during major earthquakes is commonly neglected.This study proposes new nonlinear PA procedures that consider shear failure at BCJs and seek to assess the actual damage to RC structures.Based on the specifications of FEMA-356,a simplified joint model composed of two nonlinear cross struts placed diagonally over the location of the plastic hinge is established,allowing a sophisticated PA to be performed.To verify the validity of this method,the analytical results for the capacity curves and the failure mechanism derived from three different full-size RC frames are compared with the experimental measurements.By considering shear failure at BCJs,the proposed nonlinear analytical procedures can be used to estimate the structural behavior of RC frames,including seismic capacity and the progressive failure sequence of joints,in a precise and effective manner. 相似文献