共查询到20条相似文献，搜索用时 31 毫秒
1.
Pumping test evaluation of stream depletion parameters 总被引：1，自引：0，他引：1
2.
Dominique Sorel John A. Cherry Suzanne Lesage 《Ground Water Monitoring & Remediation》1998,18(1):114-125
The in situ vertical circulation column (ISVCC) is a cylindrical containment system consisting of an instrumented steel cylinder used for experimental ground water studies in sandy aquifers. Vertical flow is imposed inside the ISVCC. Although vertical wells are an option, the ISVCC installed in the Borden Aquifer is instrumented with horizontal wells and monitoring ports to avoid creating vertical preferential flow paths. The cylinder was driven downward into the aquifer using a small backhoe equipped with a vibrating plate. The ISVCC penetrates the 2.3-m-thic sand aquifer and is keyed 20 cm into the underlying clay aquitard. The cylinder was installed inside a 2 m X 2 m steel sheet pile enclosure so that the enclosed segment of aquifer could be conveniently dewatered and then excavated to allow installation of the horizontal wells. The dispersivity of the column was comparable to literature values for long sand-packed laboratory columns.
Pure phase DNAPL (tetrachloroethene and 1,1,1-trichloroethane) was slowly pumped into two ports in the center of the column. Following this DNAPL injection, an aqueous solution of vitamin B12 and reduced titanium was circulated through the column to promote degradation of the solvents. Processes observed in the ISVCC included DNAPL distribution, dissolution, and degradation, and geochemical evolution of the aquifer.
The ISVCC provides a convenient means for testing in situ technologies in the experimental stage or for selection of proven technologies to find the most effective at a specific site. It is inexpensive, easy to install, and maximizes control over flow distribution in a heterogeneous aquifer. Its application will be restricted where low hydraulic conductivity beds are present in the aquifer. 相似文献
Pure phase DNAPL (tetrachloroethene and 1,1,1-trichloroethane) was slowly pumped into two ports in the center of the column. Following this DNAPL injection, an aqueous solution of vitamin B
The ISVCC provides a convenient means for testing in situ technologies in the experimental stage or for selection of proven technologies to find the most effective at a specific site. It is inexpensive, easy to install, and maximizes control over flow distribution in a heterogeneous aquifer. Its application will be restricted where low hydraulic conductivity beds are present in the aquifer. 相似文献
3.
Analytical solutions of drawdown in unconfined aquifers are widely applied for determining the specific yield, Sy, and the horizontal and the vertical hydraulic conductivity Kr and Kz, respectively. In many previous studies, estimates of Sy and Kz were observed to be highly variable and physically unrealistic. This has been attributed to the conceptualization of flow above the declining water table and aquifer heterogeneity in the applied models. We present the analysis of time-drawdown data from a pumping test instrumented with depth-differentiated observation piezometers arranged in clusters. Applying homogeneous anisotropic aquifer models in combination with nonlinear least squares parameter identification techniques, the data were analyzed in different groups: analysis of data from individual piezometer clusters and simultaneous analysis of the entire data set from all piezometer clusters (global analysis). From the cluster analyses, estimates of Sy and Kz exhibit large variances and depart from a priori estimates inferred from the hydrostratigraphy. Parameter estimates from the global analysis do not fall within the parameter bounds (minimum and maximum values) defined by the cluster analyses. While heterogeneity appears to be the important reason for large parameter variances, we discuss the influence of rarely considered aquifer return flow on drawdown and the inconsistent results from the cluster and global analyses. We corroborate our findings with data on hydraulic gradients, slug test data, and results from the application of a more realistic numerical flow model. 相似文献
4.
Most published solutions for aquifer responses to ocean tides focus on the one-sided attenuation of the signal as it propagates inland. However, island aquifers experience periodic forcing from the entire coast, which can lead to integrated effects of different tidal signals, especially on narrow high-permeability islands. In general, studies disregard a potential time lag as the tidal wave sweeps around the island. We present a one-dimensional analytical solution to the ground water flow equation subject to asynchronous and asymmetric oscillating head conditions on opposite boundaries and test it on data from an unconfined volcanic aquifer in Maui. The solution considers sediment-damping effects at the coastline. The response of Maui Aquifers indicate that water table elevations near the center of the aquifer are influenced by a combination of tides from opposite coasts. A better match between the observed ground water head and the theoretical response can be obtained with the proposed dual-tide solution than with single-sided solutions. Hydraulic diffusivity was estimated to be 2.3 × 107 m2 /d. This translates into a hydraulic conductivity of 500 m/d, assuming a specific yield of 0.04 and an aquifer thickness of 1.8 km. A numerical experiment confirmed the hydraulic diffusivity value and showed that the y -intercepts of the modal attenuation and phase differences estimated by regression can approximate damping factors caused by low-permeability units at the boundary. 相似文献
5.
Steady interface flow in heterogeneous aquifer systems is simulated with single‐density groundwater codes by using transformed values for the hydraulic conductivity and thickness of the aquifers and aquitards. For example, unconfined interface flow may be simulated with a transformed model by setting the base of the aquifer to sea level and by multiplying the hydraulic conductivity with 41 (for sea water density of 1025 kg/m3). Similar transformations are derived for unconfined interface flow with a finite aquifer base and for confined multi‐aquifer interface flow. The head and flow distribution are identical in the transformed and original model domains. The location of the interface is obtained through application of the Ghyben‐Herzberg formula. The transformed problem may be solved with a single‐density code that is able to simulate unconfined flow where the saturated thickness is a linear function of the head and, depending on the boundary conditions, the code needs to be able to simulate dry cells where the saturated thickness is zero. For multi‐aquifer interface flow, an additional requirement is that the code must be able to handle vertical leakage in situations where flow in an aquifer is unconfined while there is also flow in the aquifer directly above it. Specific examples and limitations are discussed for the application of the approach with MODFLOW. Comparisons between exact interface flow solutions and MODFLOW solutions of the transformed model domain show good agreement. The presented approach is an efficient alternative to running transient sea water intrusion models until steady state is reached. 相似文献
6.
An understanding of the hydraulic properties of the aquifer and the depth distribution of salts is critical for evaluating the potential of ground water for conjunctive water use and for maintaining suitable ground water quality in agricultural regions where ground water is used extensively for irrigation and drinking water. The electrical conductivity profiles recorded in a well using the flowing fluid electric conductivity (FEC) logging method can be analyzed to estimate interval-specific hydraulic conductivity and estimates of the salinity concentration with depth. However, operating irrigation wells commonly allow limited access, and the traditional equipment used for FEC logging cannot fit through the small access pipe intersecting the well. A modified, miniaturized FEC logging technique was developed for use in wells with limited access. In addition, a new method for injecting water over the entire screened interval of the well reduces the time required to perform FEC logging. 相似文献
7.
Electro-osmosis (EO), the movement of water through porous media in response to an electric field, offers a means for extracting contaminated ground water from fine-grained sediments, such as clays, that are not easily amenable to conventional pump-and-treat approaches. The EO-induced water flux is proportional to the voltage gradient in a manner analogous to the flux dependence on the hydraulic gradient under Darcy's law. The proportionality constant, the soil electro-osmotic conductivity or keo , is most easily measured in soil cores using bench-top tests, where flow is one-dimensional and interfering effects attributable to Darcy's law can be directly accounted for. In contrast, quantification of EO fluxes and keo in the field under deployment conditions can be difficult because electrodes are placed in ground water wells that may be screened across a heterogeneous mixture of lithologies. As a result, EO-induced water fluxes constitute an approximate radial flow system that is superimposed upon a Darcy flow regime through permeable pathways that may or may not be coupled with hydraulic head differences created by the EO-induced water fluxes. A single well comparative tracer test, which indirectly measures EO fluxes by comparing wellbore tracer dilution rates between background and EO-induced water fluxes, may provide a means for routinely quantifying the efficacy of EO systems in such settings. EO fluxes measured in field tests through this technique at a ground water contamination site were used to estimate a mean keo value through a semianalytic line source model of the electric field. The resulting estimate agrees well with values reported in the literature and with values obtained with bench-top tests conducted on a soil core collected in the test area. 相似文献
8.
Hydraulic Conductivity Measurements in the Unsaturated Zone Using Improved Well Analyses 总被引：4，自引：0，他引：4
The flow of ponded water into and through the unsaturated zone depends on both the saturated and unsaturated components of the hydraulic conductivity. Recent studies indicate that the ratio of the saturated (Kfs ) to the unsaturated (φm ) components (Kfs /φm =α*) of flow lies within prescribed bounds for most field soils, i.e., 1m−1 ≤α*≤ 100 m−1 . In addition, the fact that the calculation of Kfs and φm is not strongly dependent on the choice of α*, suggests that a site estimation of α* leads to reasonable "best estimates" of Kfs and φm when using the constant head well permeameter technique. As a consequence, measurement of the steady flow rate using only one ponded head may be all that is necessary for many practical applications. Multiple head measurements or independent measurements of α* or φm can be used, however, to give more accurate estimates of Kfs if required. 相似文献
9.
A new method was developed for characterizing geohydrologic columns that extended >600 m deep at sites with as many as six discrete aquifers. This method was applied at 12 sites within the Southwest Florida Water Management District. Sites typically were equipped with multiple production wells, one for each aquifer and one or more observation wells per aquifer. The average hydraulic properties of the aquifers and confining units within radii of 30 to >300 m were characterized at each site. Aquifers were pumped individually and water levels were monitored in stressed and adjacent aquifers during each pumping event. Drawdowns at a site were interpreted using a radial numerical model that extended from land surface to the base of the geohydrologic column and simulated all pumping events. Conceptually, the radial model moves between stress periods and recenters on the production well during each test. Hydraulic conductivity was assumed homogeneous and isotropic within each aquifer and confining unit. Hydraulic property estimates for all of the aquifers and confining units were consistent and reasonable because results from multiple aquifers and pumping events were analyzed simultaneously. 相似文献
10.
Predicting the future performance of horizontal wells under varying pumping conditions requires estimates of basic aquifer parameters, notably transmissivity and storativity. For vertical wells, there are well-established methods for estimating these parameters, typically based on either the recovery from induced head changes in a well or from the head response in observation wells to pumping in a test well. Comparable aquifer parameter estimation methods for horizontal wells have not been presented in the ground water literature. Formation parameter estimation methods based on measurements of pressure in horizontal wells have been presented in the petroleum industry literature, but these methods have limited applicability for ground water evaluation and are based on pressure measurements in only the horizontal well borehole, rather than in observation wells. This paper presents a simple and versatile method by which pumping test procedures developed for vertical wells can be applied to horizontal well pumping tests. The method presented here uses the principle of superposition to represent the horizontal well as a series of partially penetrating vertical wells. This concept is used to estimate a distance from an observation well at which a vertical well that has the same total pumping rate as the horizontal well will produce the same drawdown as the horizontal well. This equivalent distance may then be associated with an observation well for use in pumping test algorithms and type curves developed for vertical wells. The method is shown to produce good results for confined aquifers and unconfined aquifers in the absence of delayed yield response. For unconfined aquifers, the presence of delayed yield response increases the method error. 相似文献
11.
Hawkins JW 《Ground water》2004,42(1):119-125
Prevention of acid mine drainage at surface coal mines in the Appalachian region relies to an extent on minimizing ground water contact with acid-forming materials, and maximizing ground water contact with alkalinity-yielding materials. Acid-forming materials are often selectively handled to minimize or prevent contact with ground water. Controlling ground water contact with acidic or alkaline materials depends on forecasting the level and range of fluctuation of the postmining water table within the mine backfill. Physical measurements and aquifer testing of more than 120 wells from 18 reclaimed mines in Kentucky, Ohio, Pennsylvania, and West Virginia have led to improved forecasting of the postmining ground water system. Factors that influence the ground water regime include spoil lithology and particle size, age of reclamation, spoil thickness, distance from the final highwall, and pit floor dip angle and direction. Spoil hydraulic conductivity (K) exhibits a 95% confidence interval range of six orders of magnitude about a mean K of 1.7 x 10(-5) m/sec. Spoil aquifer saturated thickness is related to the overall thickness of the spoil, the lithology of the spoil, dip of the pit floor, and distance to the highwall. Saturated spoil thickness has a 95% confidence interval of 2.2 to 3.6 m about the mean of 2.9 m. The predicted saturated zone averages 19% of the total spoil thickness. 相似文献
12.
Numerical flow models can be a useful tool for dimensioning water wells and to investigate the hydraulics in their near‐field. Fully laminar flow can be assumed for all models calculated up to the screen. Therefore models can be used to predict—at least qualitatively, neglecting turbulent losses inside the well—the spatial distribution of inflow into the well and the overall hydraulic performance of different combinations of aquifer parameters and technical installations. Models for both horizontal (plan view) and vertical flow (cross section) to wells were calculated for a variety of setups. For the latter, this included variations of hydraulic conductivity of the screen, pump position, and aquifer heterogeneity. Models of suction flow control devices showed that they indeed can homogenize inflow, albeit at the cost of elevated entrance losses. 相似文献
13.
Well water temperatures are often collected simultaneously with water levels; however, temperature data are generally considered only as a water quality parameter and are not utilized as an environmental tracer. In this paper, water levels and seasonal temperatures are used to estimate hydraulic conductivities in a stream-aquifer system. To demonstrate this method, temperatures and water levels are analyzed from six observation wells along an example study site, the Russian River in Sonoma County, California. The range in seasonal ground water temperatures in these wells varied from <0.2 degrees C in two wells to approximately 8 degrees C in the other four wells from June to October 2000. The temperature probes in the six wells are located at depths between 3.5 and 7.1 m relative to the river channel. Hydraulic conductivities are estimated by matching simulated ground water temperatures to the observed ground water temperatures. An anisotropy of 5 (horizontal to vertical hydraulic conductivity) generally gives the best fit to the observed temperatures. Estimated conductivities vary over an order of magnitude in the six locations analyzed. In some locations, a change in the observed temperature profile occurred during the study, most likely due to deposition of fine-grained sediment and organic matter plugging the streambed. A reasonable fit to this change in the temperature profile is obtained by decreasing the hydraulic conductivity in the simulations. This study demonstrates that seasonal ground water temperatures monitored in observation wells provide an effective means of estimating hydraulic conductivities in alluvial aquifers. 相似文献
14.
Recent research has shown that planting deep-rooted trees, such as poplar, can take up and degrade important ground water pollutants such as trichloroethylene (TCE) as they transpire water from the capillary fringe of shallow contaminated aquifers. The effect of hydrogeologic factors on the minimum plantation area needed to prevent downgradient migration of contaminated ground water is not well known. Accordingly, the objective of this research was to identify the hydrogeologic parameters that control phytoremediation effectiveness. We used a numerical ground water flow model to evaluate the effect that natural variations in hydrogeologic parameters and growing season duration have on the minimum plantation area required for capture. We found that the plantation area that was needed to completely capture a ground water contamination plume was directly proportional to aquifer horizontal hydraulic conductivity, saturated thickness, and ground water gradient. The plantation area needed for capture increased nonlinearly with increasing plume width, aquifer anisotropy, and decreasing growing season duration. The plantation area needed for capture was generally insensitive to aquifer-specific yield and storativity. Steady-state simulations can be used to predict the plantation area needed for capture in many applications. A particularly important finding of this work is that evapotranspiration fluxes through plantations appropriately sized to contain the plume substantially exceeded the ground water flux through the plume itself. 相似文献
15.
Depth-discrete aquifer in formal ion was obtained using recently developed adaptations and improvements to conventional characterization techniques. These improvements included running neutron porosity and hulk density geophysical logging tools through a cased hole, performing an enhanced point-dilution tracer test for monitoring tracer concentration as a function of Lime and depth, and using pressure derivatives for diagnostic and quantitative analysis of constant rate discharge lest data. Data results from the use of these techniques were used to develop a conceptual model of a heterogeneous aquifer. Depth-discrete aquifer information was required to effectively design field-scale deployment and monitoring of an in situ bioremediation technology.
Geophysical logging and point-dilution tracer test results provided the relative distribution of porosity and horizontal hydraulic conductivity, respectively, with depth and correlated well. Hydraulic pumping tests were conducted to estimate mean values for transmissivity and effective hydraulic conductivity, Tracer lest and geophysical logging results indicated that ground water flow was predominant in the upper approximate 10 feet of the aquifer investigated. These results were used to delineate a more representative interval thickness for estimating effective hydraulic conductivity. Hydraulic conductivity, calculated using this representative interval, was estimated lo be 73 ft/d, approximately three limes higher than that calculated using the full length of the screened test interval. 相似文献
Geophysical logging and point-dilution tracer test results provided the relative distribution of porosity and horizontal hydraulic conductivity, respectively, with depth and correlated well. Hydraulic pumping tests were conducted to estimate mean values for transmissivity and effective hydraulic conductivity, Tracer lest and geophysical logging results indicated that ground water flow was predominant in the upper approximate 10 feet of the aquifer investigated. These results were used to delineate a more representative interval thickness for estimating effective hydraulic conductivity. Hydraulic conductivity, calculated using this representative interval, was estimated lo be 73 ft/d, approximately three limes higher than that calculated using the full length of the screened test interval. 相似文献
16.
Closed‐form solutions are proposed for natural seepage in semiconfined (leaky) aquifers such as those existing below the massive Champlain Sea clay layers in the Saint‐Lawrence River Valley. The solutions are for an ideal horizontal leaky aquifer below an ideal aquitard that may have either a constant thickness and a constant hydraulic head at its surface, or a variable thickness and a variable hydraulic head at its surface. A few simplifying assumptions were needed to obtain the closed‐form solutions. These have been verified using a finite element method, which did not make any of the assumptions but gave an excellent agreement for hydraulic heads and groundwater velocities. For example, the difference between the two solutions was smaller than 1 mm for variations in the 5 to 8 m range for the hydraulic head in the semiconfined aquifer. Note that fitting the hydraulic head data of monitoring wells to the theoretical solutions gives only the ratio of the aquifer and aquitard hydraulic conductivities, a clear case of multiple solutions for an inverse problem. Consequently, field permeability tests in the aquitard and the aquifer, and pumping tests in the aquifer, are still needed to determine the hydraulic conductivity values. 相似文献
17.
Estimating the Horizontal Gradient in Heterogeneous, Unconfined Aquifers: Comparison of Three-Point Schemes 总被引：1，自引：0，他引：1
At least two approaches may be used to estimate the horizontal components of the hydraulic gradient based on measured heads from three observation points. First, the gradient may be estimated by passing a plane through the measured heads (h-method). Second, if the elevation of the base of the aquifer is known to be spatially constant, an estimate of the gradient may be obtained using the squares of the measured heads (h2 - method). In the present study, these methods are examined in application to a heterogeneous system. Using Monte Carlo analysis, we demonstrate that the magnitude of the gradient estimated via the h-method involved significant bias, which increased when the distance separating the wells increased. In contrast, bias in the estimated magnitude of the gradient based on the h2 -method decreased with increasing separation among the wells. Estimation variances for both the magnitude and orientation of the gradient also decreased with separation distance. The variance in the orientation was observed to remain relatively high, however, even at relatively large separations among the wells (e.g., 10 integral scales). These results are Interpreted as implying that the best estimate of the gradient for steady flow in an unconfined aquifer is derived from the h2 - method with the wells separated by significant distances. These results also demonstrate the uncertainty inherent in estimating the gradient based on limited field data. 相似文献
18.
The Bouwer and Rice method of estimating the saturated hydraulic conductivity (Ks) from slug-test data was evaluated for geometries typical of hand-dug wells. A two-dimensional, radially symmetric and variably saturated, ground water transport model was used to simulate well recovery given a range of well and aquifer geometries and unsaturated soil properties, the latter in terms of the van Genuchten parameters. The standard Bouwer and Rice method, when applied to the modeled recharge rates, underestimated Ks by factors ranging from 1.3 to 5.6, depending on the well geometry and the soil type. The Bouwer and Rice analytical solution was modified to better explain the recovery rates as predicted by the numerical model, which revealed a significant dependence on the unsaturated soil for the shallow and wide geometries that are typical of traditional wells. The modification introduces a new parameter to the Bouwer and Rice analysis that is a measure of soil capillarity which improves the accuracy of Ks estimates by tenfold for the geometries tested. 相似文献
19.
Eloctromigraiion offers a potential tool for remediating ground water contaminated with highly soluble components, such as Na+ , Cl, NO3 and SO4 − . A field experiment was designed to lest the efficacy of electromigration for preconcontrating dissolved SO4 2 in ground water associated with a fossil-fuel power plant. Two shallow wells, 25 feel apart (one 25 feel deep, the other 47 feet deep), were constructed in the upper portion of an unconfined alluvial aquifer. The wells were constructed with a double-wall design, with an outer casing of 4-inch PVC and an inner lube of 2-inch FVC; both were fully slotted (0.01 inch). Electrodes were constructed by wrapping the inner lulling with a 100-foot length of rare-earth metal oxide/copper wire. An electrical potential of 10.65 volts DC Was applied, and tests were run for periods of 12, 44, and 216 hours. Results showed large changes in the pH from the initial pH of ground water of about 7.5 to values of approximately 2 and 12 at the anode and cathode, respectively. Despite the fact that the test conditions were far from ideal, dissolved SO4 2- ; was significantly concentrated at the anode. Over a period of approximately nine days, the concentration of SO4 2- at the anode reached what appeared to he a steady-state value of 2200 mg/L. compared lo the initial value in ground water of approximately 1150 mg/L. The results of this field lest should encourage further investigation of electromigration as a tool in the remediation of contaminated ground water. 相似文献
20.
James E. Landmeyer Francis H. Chapelle Paul M. Bradley James F. Pankow Clinton D. Church Paul G. Tratnyek 《Ground Water Monitoring & Remediation》1998,18(4):93-102
Methyl tert -butyl ether (MTBE) and benzene have been measured since 1993 in a shallow, sandy aquifer contaminated by a mid-1980s release of gasoline containing fuel oxygenates. In wells downgradient of the release area, MTBK was detected before benzene, reflecting a chromatographic-like separation of these compounds in the direction of ground water flow. Higher concentrations of MTBE and benzene were measured in the deeper sampling ports of multilevel sampling wells located near the release area, and also up to 10 feet (3 m) below the water table surface in nested wells located farther from the release area. This distribution of higher concentrations at depth is caused by recharge events that deflect originally horizontal ground water flowlines. In the laboratory, microcosms containing aquifer material incubated with uniformly labeled 14 C-MTBE under aerobic and anaerobic. Fe(III)-reducing conditions indicated a low but measurable biodegradation potential (<3%14 C-MTBW as 14 CO2 ) after a seven-month incubation period, Tert -butyl alcohol (TBA), a proposed microbial-MTBE transformation intermediate, was detected in MTBE-contaminated wells, but TBA was also measured in unsaturated release area sediments. This suggests that TBA may have been present in the original fuel spilled and does not necessarily reflect microbial degradation of MTBE. Combined, these data suggest that milligram per liter to microgram per liter decreases in MTBE concentrations relative to benzene are caused by the natural attenuation processes of dilution and dispersion with less-contaminated ground water in the direction of flow rather than biodegradation at this point source gasoline release site. 相似文献