共查询到20条相似文献，搜索用时 140 毫秒
1.
就橡胶垫隔震体系和摩擦摆隔震体系,研究分析大型立式储液罐在不同场地实际地震作用下的响应,同时将地震响应与非隔震储罐进行对比分析。分析结果表明:在柔软场地,摩擦摆隔震系统的减震效果要好于橡胶垫系统。摩擦摆支座控制隔震层位移的能力要好于橡胶垫支座。此外,进行了参数影响分析,来衡量储罐储液量、高径比和隔震系统的隔震周期对储罐主要响应的影响。储罐储液量较小时,摩擦摆支座的减震率要好于橡胶垫支座。隔震储罐高径比不宜取为0.8,此时脉冲位移和基底剪力的峰值响应都较大。隔震周期在2 s～3 s区间范围内时,可以取得最优减震效果。 相似文献
2.
隔震立式储罐地震反应谱分析 总被引：4，自引：2，他引：2
基于反应谱理论,研究了的基底隔震储罐的地震响应问题.将储罐简化为三质点体系力学模型,罐内连续液体质量等效为对流质量、脉冲质量和刚性质量,并引入隔震刚度.与时程分析对比,验证反应谱法的适用性,分析隔震立式储罐的地震响应并研究主要参数对隔震储液罐地震响应的影响,主要考虑的参数有:(1)场地类别;(2)隔震周期;(3)高径比.结果表明:反应谱法计算隔震立式储罐地震响应是偏于安全的;随着场地类别和隔震周期的增大,基底剪力减震率逐渐降低,晃动波高变化不明显,隔震后,液动压力呈线性变化,液动压力随着场地类别和高径比的增大而增大,随着隔震周期的增大而减小;高径比存在一定的优化段,在优化段内,基底剪力减震率较大,隔震效果较好. 相似文献
3.
《地震工程与工程振动》2017,(2)
为了避免立式储罐自复位滚动隔震体系的支座位移过大导致支座失效,同时达到在不同地震动作用下,减震效应明显的目的,设计了一种变刚度限位滚动隔震装置,以便适应地震动特性变化以及储液高度变化的影响。利用有限元分析软件ADINA进行数值仿真分析,采用弹簧-阻尼系统模拟隔震层,非线性弹簧单元模拟限位装置,流体采用势流体单元,罐壁采用壳单元,建立15×104m3储罐模型。在加速度峰值为0.4 g不同地震动激励下,尤其是近断层长周期地震作用下,对加入限位装置前后储罐的地震响应进行对比,结果表明:采用限位装置后,支座位移得到明显控制,基底剪力、基底弯矩以及动液压力却都有不同程度的放大,但相比非隔震情况下仍有较好的隔震效果,晃动波高略有增大。建议在采用变刚度滚动隔震措施时,可考虑综合减震方案,优化减震效果。 相似文献
4.
为了研究桩土、隔震层与罐体相互作用对15×104m3隔震储罐地震响应的影响,桩与隔震层采用弹簧-阻尼单元,罐体采用壳单元,流体采用势流体单元,基于ADINA建立数值仿真分析模型,在8度E1 Centro地震动激励下,应用Newmark数值积分方法进行地震响应分析.结果表明:隔震储罐基底剪力和基底弯矩相对于非隔震储罐明显降低,储罐罐壁加速度沿罐壁高度方向近乎平动,但对波高的控制效果不明显;除罐壁顶部外,动液压力明显降低;隔震后,罐壁有效应力和环向应力减震效应明显,对轴向应力和径向应力影响较小,建议从安全角度考虑,储罐非隔震设计时不考虑桩土作用,隔震设计时考虑桩土对罐体的影响. 相似文献
5.
为了研究15×104m3立式储罐隔震设计影响因素,采用有限元数值仿真技术,分析了隔震刚度、浮顶质量、储液密度、罐壁厚度、罐壁的材料弹性模量、储液高度与罐半径比值对储罐的晃动频率和液固耦合频率的影响并与时程分析对照。结果表明:储罐液固耦合振动频率对隔震刚度敏感,隔震刚度较低时,液固耦合刚度的下降,使基底剪力变小;隔震刚度对储罐的液体晃动频率的影响不大,在一定的隔震周期范围内,波高无放大效应;隔震设计时,浮顶的影响可忽略;储液高度与储罐半径比对储罐的液固耦合频率和晃动频率影响较大,隔震设计时存在优化段;储液密度、罐壁厚度、材料弹性模量,隔震设计时可不考虑其影响,进行地震动台实验时,可考虑用其他材料代替钢材,不影响分析结果。 相似文献
6.
《世界地震工程》2016,(1)
利用ADINA软件建立董家口16万立方米LNG储罐的有限元模型,在模型中分别设置不同水平刚度、不同隔震频率和阻尼比的夹层橡胶垫作为储罐的隔震装置。对比了隔震前后储罐的位移和加速度反应的变化,同时分析了采用不同隔震参数支座的储罐在液固耦合作用下,储罐内部液面晃动的变化情况。结果表明:夹层橡胶支座的水平刚度对储罐隔震效果的作用不明显,但夹层橡胶支座的隔震频率和阻尼比对储罐隔震效果的影响显著。隔震频率和阻尼比越大,对内外罐位移和加速度的控制效果越明显。因为基底剪力、基底倾覆弯矩和动液压力会增大,而且隔震装置会放大储罐的晃动波高,所以在选取隔震支座时,要综合考虑储罐高径比、隔震支座的隔震频率和阻尼比等参数,选取最优组合,从而达到最佳的减震效果。 相似文献
7.
立式储液罐橡胶基底隔震模型实验研究 总被引：2，自引：0，他引：2
针对立式储液罐地震响应问题,引伸土木结构控制思想,建立了立式储液罐橡胶基底隔震体系的试验模型,进行了地震动试验,试验结果表明,隔震体系对减轻短周期的地震影响是有效的,但对长周期的地震影响是无效的。 相似文献
8.
高层摩擦摆基础隔震结构在远场长周期地震动长持时的长周期成份作用下,尤其是类谐波成份作用下,隔震层上部结构的减震性能将可能无法得到保证,且摩擦摆支座亦可能产生超限变形。为此,远场长周期地震动作用下高层摩擦摆基础隔震结构的减震性能需进一步探讨。通过一幢框架-核心筒高层摩擦摆基础隔震结构的非线性地震响应分析,揭示远场长周期地震动,尤其是在类谐和长周期地震动下框架-核心筒高层摩擦摆基础隔震结构的地震响应规律。提出在隔震层增设黏滞阻尼器对结构的地震响应进行控制。结果表明:摩擦摆隔震不能满足结构在远场类谐和长周期地震动作用的减震要求,而且还将放大其作用下结构的非线性响应;组合隔震结构能较有效地控制长周期地震动、特别是远场类谐和长周期地震作用下隔震层上部结构以及隔震层的弹塑性地震响应,尤其可显著减小隔震支座的最大变形,使其不超越隔震支座的容许变形值。 相似文献
9.
抗拔型三重摩擦摆隔震支座是一种新型隔震支座。以框架结构为例,利用ANSYS软件建立了6层和10层普通抗震结构和带该支座的基础隔震结构模型;通过模态分析,得到了结构的自振周期;通过地震响应分析,提取了6层框架隔震层和顶层的位移、加速度和剪力时程曲线,并提取了不同层数不同结构类型的各层间位移、加速度幅值。结果表明：与抗震结构相比,基础隔震结构周期显著增大;隔震结构的变形主要集中在隔震层,隔震层以上的结构基本为整体平动,结构的地震位移反应得到了有效的减小;采用抗拔型三重摩擦摆隔震支座能降低结构地震加速度反应;设置抗拔型三重摩擦摆隔震支座的多层数隔震结构的能量衰减不如低层数的隔震结构迅速。 相似文献
10.
11.
Curved surface sliding bearings, which are usually called as friction pendulum system (FPS) are commonly used for base isolation of liquid storage tanks since the period of the isolation system is independent of the storage level. However the restoring force and the damping at the isolation system are functions of axial load which changes during an earthquake excitation. This change might be in appreciable amounts especially for the tanks with high aspect ratios. The present paper focuses on earthquake performances of both broad and slender tanks base isolated by FPS bearings. The effects of overturning moment and vertical acceleration on axial load variation at the bearings are considered. The efficiency of the isolation system is investigated by analyzing the effects of various parameters such as; (i) isolation period, (ii) tank aspect ratio and (iii) coefficient of friction. The Haroun and Housner's three-degrees-of-freedom lumped mass model was used to solve the governing equations of motion in which convective, impulsive and rigid masses were included. A number of selected ground motions were considered and the results were compared to those of non-isolated cases.As a result, base isolation was found to be effective in reducing the base shear values for both broad and slender tanks without significantly affecting the sloshing displacements of the broad ones. The efficiency was even more pronounced for slender tanks subjected to near fault ground motions for isolation periods above 3 s. This specific value of isolation period also eliminated possible design problems arising from under-estimation of base shear values (up to 40%) due to ignoring the effects of axial load variation in lower isolation periods. Overturning effects should not be ignored especially for tanks with high aspect ratios (S) and being subjected to near fault ground motion. 相似文献
12.
The seismic response of an isolated vertical, cylindrical, extra-large liquefi ed natural gas (LNG) tank by a multiple friction pendulum system (MFPS) is analyzed. Most of the extra-large LNG tanks have a fundamental frequency which involves a range of resonance of most earthquake ground motions. It is an effective way to decrease the response of an isolation system used for extra-large LNG storage tanks under a strong earthquake. However, it is diff icult to implement in practice with common isolation bearings due to issues such as low temperature, soft site and other severe environment factors. The extra-large LNG tank isolated by a MFPS is presented in this study to address these problems. A MFPS is appropriate for large displacements induced by earthquakes with long predominant periods. A simplifi ed fi nite element model by Malhotra and Dunkerley is used to determine the usefulness of the isolation system. Data reported and statistically sorted include pile shear, wave height, impulsive acceleration, convective acceleration and outer tank acceleration. The results show that the isolation system has excellent adaptability for different liquid levels and is very effective in controlling the seismic response of extra-large LNG tanks. 相似文献
13.
The effect of spatially varying earthquake ground motions on the stochastic response of bridges isolated with friction pendulum systems 总被引：1，自引：0，他引：1
Sevket Ates Alemdar Bayraktar A. Aydin Dumanoglu 《Soil Dynamics and Earthquake Engineering》2006,26(1):31-44
In this paper, a comprehensive investigation of the effect of spatially varying earthquake ground motions on the stochastic response of bridges isolated with friction pendulum systems is performed. The spatially varying earthquake ground motions are considered with incoherence, wave-passage and site-response effects. The importance of the site-response effect, which arises from the difference in the local soil conditions at different support points of the isolated bridge, is investigated particularly. Mean of maximum and variance response values obtained from the spatially varying earthquake ground motions are compared with those of the specialised cases of the ground motion model. It is shown that site-response component of the spatially varying earthquake ground motion model has important effects on the stochastic response of the isolated bridges. Therefore, to be more realistic in calculating the isolated bridge responses, the spatially varying earthquake ground motions should be incorporated in the analysis. 相似文献
14.
A common effective method to reduce the seismic response of liquid storage tanks is to isolate them at base using base-isolation systems. It has been observed that in many earthquakes, the foregoing systems significantly affect on the whole system response reduction. However, in exceptional cases of excitation by long-period shaking, the base-isolation systems could have adverse effects. Such earthquakes could cause tank damage due to excessive liquid sloshing. Therefore, the numerical seismic response of liquid storage tanks isolated by bilinear hysteretic bearing elements is investigated under long-period ground motions in this research. For this purpose, finite shell elements for the tank structure and boundary elements for the liquid region are employed. Subsequently, fluid–structure equations of motion are coupled with governing equation of base-isolation system, to represent the whole system behavior. The governing equations of motion of the whole system are solved by an iterative and step-by-step algorithm to evaluate the response of the whole system to the horizontal component of three ground motions. The variations of seismic shear forces, liquid sloshing heights, and tank wall radial displacements are plotted under various system parameters such as the tank geometry aspect ratio (height to radius), and the flexibility of the isolation system, to critically examine the effects of various system parameters on the effectiveness of the base-isolation systems against long-period ground motions. From these analyses, it may be concluded that with the installation of this type of base-isolation system in liquid tanks, the dynamic response of tanks during seismic ground motions can be considerably reduced. Moreover, in the special case of long-period ground motions, the seismic response of base-isolated tanks may be controlled by the isolation system only at particular conditions of slender and broad tanks. For the case of medium tanks, remarkable attentions would be required to be devoted to the design of base-isolation systems expected to experience long-period ground motions. 相似文献
15.
Sandip Kumar Saha Vasant A. Matsagar Arvind K. Jain 《Bulletin of Earthquake Engineering》2016,14(4):1153-1175
Seismic fragility curves for fixed-base and base-isolated liquid storage tanks are developed under non-stationary earthquakes, and their seismic performance are compared. The correlation between different earthquake intensity measure (IM) parameters and peak response quantities of the base-isolated liquid storage tanks are investigated. The failure criteria are chosen based on (1) the elastic buckling strength of the tank wall, which is defined in terms of critical base shear and critical overturning moment, and (2) in terms of the critical isolation displacement. The uncertainty involved is considered in the earthquake characteristics. Non-stationary earthquake ground motions are generated using Monte Carlo (MC) simulation. Influence of the isolator characteristic parameters and modeling approaches on the seismic fragility of the base-isolated liquid storage tanks is also investigated. Peak ground acceleration is found to be the well correlated IM parameter with the peak response quantities of the base-isolated liquid storage tanks. Substantial decrease in the seismic fragility of the base-isolated liquid storage tanks is observed as compared to the fixed-base tanks. Significant influence of the isolator characteristic parameters on the seismic fragility of the base-isolated liquid storage tanks are reported in the present study. 相似文献
16.
Storage tanks are vulnerable to earthquakes, as numerous major earthquakes have demonstrated. The trend of recent revisions to make seismic design criteria for large‐scale industrial storage tanks increasingly stringent has made development of cost‐effective earthquake‐resistant design and retrofit techniques for industrial tanks imperative. This study assesses the feasibility of seismic base isolation for making liquid‐filled storage tanks earthquake resistant. The sliding‐type friction pendulum seismic (FPS) bearings are considered rather than the elastomeric bearings because the dynamic characteristics of an FPS‐isolated tank remain unchanged regardless of the storage level. This work has devised a hybrid structural‐hydrodynamic model and solution algorithm, which would permit simple, accurate and efficient assessment of the seismic response of rigid cylindrical storage tanks in the context of seismic isolation. Extensive numerical simulations confirm the effectiveness of seismic base isolation of rigid cylindrical tanks using FPS bearings. Copyright © 2001 John Wiley & Sons, Ltd. 相似文献
17.
Liquid storage tanks are essential structures that are often located in residential and industrial areas; thus an assessment of their seismic performance is an important engineering issue. In this paper, the seismic response of unanchored steel liquid storage tanks is investigated using the endurance time (ET) dynamic analysis procedure and compared to responses obtained for anchored tanks under actual ground motions and intensifying ET records. In most cases, the results from ground motions are properly obtained with negligible differences using ET records. It is observed that uplifting of the tank base, which is closely related to the tank aspect ratio, has the greatest significance in the responses of the tank and can be predicted with reasonable accuracy by using currently available ET records. 相似文献
18.
The seismic response of a benchmark highway bridge isolated with passive polynomial friction pendulum isolators (PFPIs) is investigated and subjected to six bidirectional ground motion records. The benchmark study is based on a lumped mass finite-element model of the 91/5 highway overcrossing located in Southern California. The PFPI system possesses two important parameters; one is horizontal flexibility and the other is energy absorbing capacity through friction. The evaluation criteria of the benchmark bridge are analyzed considering two parameters, time period of the isolator and coefficient of friction of the isolation surface. The results of the numerical study are compared with those obtained from the traditional friction pendulum system (FPS). Dual design performance of the PFPI system suppressed the displacement and acceleration response of the benchmark highway bridge. The dual design hysteresis loop of the PFPI system is the main advantage over the linear hysteresis loop of the FPS. The numerical result indicates that the seismic performance of the PFPI system is better than that of the traditional FPS isolated system. Further, it is observed that variations of the isolation time period and coefficient of friction of the FPS and PFPI systems have a significant effect on the peak responses of the benchmark highway bridge. 相似文献
19.
A procedure for developing equations that estimate the isolator displacement due to strong ground motion is applied to buildings isolated with the friction pendulum system. The resulting design equations, based on rigorous non‐linear analysis, offer an alternative to the iterative equivalent‐linear methods used by current U.S. building codes. The governing equations of the system are reduced to a form such that the median normalized displacement of the system due to an ensemble of ground motions is found to depend on only the isolation period—a function of the curvature of the isolator—and the friction force at incipient slip normalized by peak ground velocity. The normalization is effective in minimizing the dispersion of the normalized displacement for an ensemble of ground motions, implying that the median normalized displacement is a reliable estimate of response. The design equations reflect the significant (20 to 38%) increase in displacement when the excitation includes two lateral components of ground motion instead of just one component. Equivalent‐linear methods are shown to underestimate by up to 30% the exact median displacement determined by non‐linear response history analysis for one component of ground motion, and building codes include at most a 4.4% increase for a second component. Copyright © 2003 John Wiley & Sons, Ltd. 相似文献
20.
This study aims at evaluating the optimal properties of friction pendulum bearings to be employed for the seismic protection of elastic isolated structural systems under earthquake excitations with different characteristics in terms of frequency content. A two-degree-of-freedom model is considered to describe the isolated system behavior while accounting for the superstructure flexibility and a non-dimensional formulation of the governing equations of motion is employed to relate the characteristic parameters describing the isolator and structure properties to the response parameters of interest for the performance assessment. Seismic excitations are modeled as time-modulated filtered Gaussian white noise random processes of different intensity within the power spectral density method. The filter parameters control the frequency content of the random excitations and are calibrated to describe stiff, medium and soft soil conditions, respectively. Finally, multi-variate regression expressions are obtained for the optimum values of the friction coefficient that minimize the superstructure displacements relative to the base mass as a function of the structural system properties, of the seismic input intensity and of the soil condition. 相似文献