共查询到16条相似文献，搜索用时 187 毫秒
1.
2.
针对地下工程抗震分析中边界条件和地震动输入方式选择问题,对一地下半无限体模型在一剪切波垂直入射条件下进行不同边界条件和不同地震动输入方法的算例试算。结果发现:两侧采用竖直向位移约束、底部采用黏弹性边界、并在模型底部用等效节点力输入地震动的方法,与三边均采用黏弹性边界条件和三边均采用等效节点荷载输入地震动的方法可以获得同样的结果。该方法易于在ANSYS中通过APDL编程实现,可为地下工程抗震分析中黏弹性边界的使用提供便利。 相似文献
3.
在ABAQUS黏弹性人工边界时域波动方法的基础上,首先运用等效应力输入方法实现地震SV波倾斜入射,半空间算例验证该方法具有较好的计算精度,进而基于所建立的斜入射方法研究地震波斜入射对海河沉管隧道地震响应的影响。计算结果表明:SV波斜入射情况下,沉管隧道的地震响应规律与垂直入射时具有明显差异;随入射角增加,沉管隧道结构应力增大,应力较大点出现在沉管隧道的四个角点及隔墙与底板、顶板的连接处,其中中隔墙为最薄弱点;随入射角增加,侧墙和隔墙的相对最大水平位移增大,其中中隔墙位移最大;随入射角增加,沉管隧道结构竖向加速度峰值明显增大。因此在沉管隧道结构抗震设计中应考虑地震波斜入射的影响。 相似文献
4.
基于黏弹性人工边界与相应地震动输入方法,推导了任意角度下三维SV波斜入射时的等效节点荷载,构建了考虑地震波斜入射的三维黏弹性静-动力统一人工边界,探究了三维情况下混凝土拱坝在地震波斜入射时的地震动响应,应用于Nam Ngum 5重力拱坝-库水-地基系统的地震响应分析中。研究结果表明：当SV波斜入射角度逐渐增大时,坝体关键点的顺河向位移、主应力以及动水压力峰值均呈现逐渐增大的趋势,横河向位移呈现逐渐减小的趋势;其中25°与0°入射相比,坝顶点顺河向位移从0增加至0.15 m,横河向位移影响较小仅减小0.011 m;坝踵点、坝趾点主应力与斜入射角度存在明显差异,当入射角度为25°时,主拉应力与主压应力峰值相较于垂直入射分别增加了1.41 MPa与3 MPa;坝踵处动水压力峰值也在入射角度为25°时达到最大为0.33 MPa与-0.29 MPa;需要在类似实际工程设计中应考虑地震波斜入射的影响。 相似文献
5.
易损性分析是评估不同强度地震作用下混凝土重力坝各级破坏概率的有效方法。目前重力坝易损性分析通常假定地震波为垂直入射,然而在近断层区域,地震波往往是倾斜入射的,地震波斜入射对重力坝地震响应有显著影响。从太平洋地震工程研究中心数据库选取16条地震动记录,采用黏弹性人工边界结合等效节点荷载实现SV波斜入射波动输入。采用增量动力分析方法对地震动峰值加速度进行调幅,以印度Koyna混凝土重力坝为研究对象,以坝顶相对位移为抗震性能指标,建立SV波斜入射下重力坝不同震损等级的易损性曲线。结果表明,与垂直入射相比,相同震损等级和相同地震动强度下,斜入射时重力坝破坏概率减小;当PGA接近重力坝实际遭受的地震动强度时,入射角为15°和30°时破坏概率与垂直入射相比最大减小率分别为27.3%和68.2%;各地震强度下,15°和30°斜入射相对于垂直入射的破坏概率差异值最大分别达36.6%、83.9%。因此,混凝土重力坝抗震性能分析应考虑地震波斜入射的影响。研究结果也可为近断层区域混凝土重力坝安全风险评估提供参考。 相似文献
6.
利用黏弹性人工边界和等效地震荷载时域波动输入方法,结合土层和半空间的精确动力刚度矩阵,实现了地震波斜入射下层状场地地下综合管廊地震反应分析,建立了不同场地条件下地下综合管廊分析模型。计算结果表明:地震波倾斜入射情况下,综合管廊结构地震响应与垂直入射时具有显著差异,一般SV波以30°临界角附近入射时结构地震反应最为剧烈;地下综合管廊动应力集中主要分布在管廊角部、中柱上下端;成层土波速结构变化对地下综合管廊地震反应亦具有显著影响。总体上看:当穿越软夹层时管廊结构地震反应更为剧烈,且覆盖层越厚,管廊结构内力幅值越大。因此地下综合管廊结构抗震设计宜考虑地震波倾斜入射及场地土层性质的影响。 相似文献
7.
在地震波场的波动方程数值模拟中,由于计算量的限制,必须加入人为的边界,使模拟计算可以在一定的空间范围内进行. 由于边界节点上的波场值不能像模拟区域内部的节点一样使用中心差分来计算,使其计算精度大大降低,从而产生边界反射. 为了消除边界反射,本文提出了延迟边界方法,根据弹性波在传播方向上等距离质点的等相位延迟性质和振幅衰减特性,由内部波场的时空分布,推算出边界波场的相位延迟的大小和振幅衰减系数,从而提高边界节点上的波场值计算精度,消除边界反射的产生. 相似文献
8.
将土体视为固-液两相介质,基于饱和土体有效应力原理,建立饱和土体-地下综合管廊结构体系相互作用动力模型:在地应力平衡的静力状态下采用Duncan-Chang非线性弹性本构模型,在地震波作用的动力状态下采用Davidenkov非线性黏弹性本构模型;考虑饱和土体黏弹性动力人工边界条件,将地震动作用转化为作用在人工边界节点上的动力荷载。模型考察不同地震波时程、地震波加速度峰值、入射角度、孔隙率以及地应力场的影响,得出如下结论:(1)地震波的卓越周期与场地卓越周期相近时引起结构上的变形最大;随着地震波加速度峰值的增大结构变形增大;随着地震波入射角度的增加结构变形增大,地震波斜入射情况下产生的行波效应使得结构变形最大。(2)土体材料的孔隙水压力是影响地震中结构变形的主要因素之一。(3)将土体材料考虑为单相介质时结构上的变形要比考虑为固-液两相介质时大得多,直接将饱和土体场地中得到的地震波等效荷载施加到单相土介质-结构动力相互作用模型上,能够得到与完全基于有效应力法一致的结果。 相似文献
9.
基于饱和两相介质弹性波动方程分析SV波在饱和土体自由表面的反射问题,引入波动方程的势函数解答,求解出二维问题中SV波入射情况下饱和土体自由场的位移、速度、加速度和应力响应。在饱和土体自由场响应解析解基础上,建立SV波入射下饱和土体自由场静、动力有限元模型。建模中考虑了如下几方面因素:(1)在不同分析步,对土体单元赋予不同材料本构。通过*model change命令进行单元生死设定,从而实现在初始应力场平衡的静力状态下采用DuncanChang本构模型,而地震波动输入时采用Davidenkov动力本构模型;(2)采用多孔介质黏弹性人工边界条件,在人工边界上分别施加固相和液相介质的弹簧和阻尼来模拟饱和土体中能量的传播;(3)将地震波转化为作用在人工边界上的等效地震荷载,施加到人工边界节点上;(4)土体单元采用4结点平面应变孔压单元(CPE4P)。有限元计算与解析解比较结果表明:SV波在垂直入射和掠入射时,竖向位移响应为零;在45°左右入射时,水平位移响应最大;60°左右入射时,竖向位移响应最大。这些结论与解析解吻合较好,本文模型为建立土-结构动力相互作用模型打下良好的基础。 相似文献
10.
传统的人工边界是在声波或弹性波分解为内行和外行分量的基础上设计的.对于较复杂的介质模型（如粘弹介质、弹塑介质、塑性介质模型等）,地震波不能简单地分解为各自满足其运动方程的纵波、横波等成分,且地震波在传播过程中还有衰减现象,因此传统的人工边界已不能有效地用于非弹性的较复杂介质的波场模拟.本文提出了一种适合于更一般的地震模型的波场计算的透射边界条件,并以粘弹介质的一个较简单的二维几何模型为例,通过有限元数值求解这种透射边界和刚性边界下粘弹波的激发和传播,得到地面合成地震记录,证明了这种透射边界用于较复杂介质波场计算是可行的. 相似文献
11.
The impact of the incident angle of earthquake motion on the seismic response of the long lined tunnels is studied. Based on the time‐domain finite element method with the viscous‐spring artificial boundary condition, the earthquake motion of oblique incidence is transformed into the equivalent nodal forces acting on the truncated boundary of finite element model. In the present work, the formulas of equivalent nodal forces for the plane P wave with arbitrary incident angle are deduced and implemented into the commercial software abaqus 1 . The effectiveness of the formulas and its implementation are demonstrated by two numerical examples with the reference solutions. The proposed method is applied to investigate the seismic responses of the long lined tunnels under the obliquely incident P waves. The numerical results indicate that the seismic responses of the long lined tunnels are highly affected by the incident angles of P waves. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
12.
《地震研究进展（英文）》2022,2(4):100179
In this study, A time-domain seismic response analysis method and a calculation model of the underground structure that can realize the input of seismic P, SV and Rayleigh waves are established, based on the viscoelastic artificial boundary elements and the boundary substructure method for seismic wave input. After verifying the calculation accuracy, a comparative study on seismic response of a shallow-buried, double-deck, double-span subway station structure under incident P, SV and Rayleigh waves is conducted. The research results show that there are certain differences in the cross-sectional internal force distribution characteristics of underground structures under different types of seismic waves. The research results show that there are certain differences in the internal force distribution characteristics of underground structures under different types of seismic waves. At the bottom of the side wall, the top and bottom of the center pillar of the underground structure, the section bending moments of the underground structure under the incidences of SV wave and Rayleigh wave are relatively close, and are significantly larger than the calculation result under the incidence of P wave. At the center of the side wall and the top floor of the structure, the peak value of the cross-sectional internal force under the incident Rayleigh wave is larger than the calculation result under SV wave. In addition, the floor of the underground structure under Rayleigh waves vibrates in both the horizontal and vertical directions, and the magnification effect in the vertical direction is more significant. Considering that the current seismic research of underground structures mainly considers the effect of body waves such as the shear waves, sufficient attention should be paid to the incidence of Rayleigh waves in the future seismic design of shallow underground structures. 相似文献
13.
地震波是一种随机的、不规则作用的动荷载脉冲,可分为振动型和冲击型。不同类型的地震波会对砂土液化和变形等产生重要影响,而传统的砂土震陷计算方法往往忽视这种因素,只考虑最大加速度幅值。通过编写UMAT子程序,在非线性有限元软件ABAQUS中开发亚塑性砂土边界面模型,对不同地震波类型下不同相对密度的砂土进行动单剪试验模拟,得到一系列砂土剪应变及竖向应变的时程曲线,并与室内试验结果进行对比分析。研究表明:在同一工况下,同类型的地震波引起的砂土竖向应变相近,不同类型引起的竖向应变差异明显;振动型地震波比冲击型引起的竖向应变更大。 相似文献
14.
Influence of seismic wave type and incident direction on the dynamic response of tall concrete-faced rockfill dams 
下载免费PDF全文
下载免费PDF全文 Owing to the stochastic behavior of earthquakes and complex crustal structure, wave type and incident direction are uncertain when seismic waves arrive at a structure. In addition, because of the different types of the structures and terrains, the traveling wave effects have different influences on the dynamic response of the structures. For the tall concrete-faced rockfill dam (CFRD), it is not only built in the complex terrain such as river valley, but also its height has reached 300 m level, which puts forward higher requirements for the seismic safety of the anti-seepage system mainly comprising concrete face slabs, especially the accurate location of the weak area in seism. Considering the limitations of the traditional uniform vibration analysis method, we implemented an efficient dynamic interaction analysis between a tall CFRD and its foundation using a non-uniform wave input method with a viscous-spring artificial boundary and equivalent nodal loads. This method was then applied to investigate the dynamic stress distribution on the concrete face slabs for different seismic wave types and incident directions. The results indicate that dam-foundation interactions behave differently at different wave incident angles, and that the traveling wave effect becomes more evident in valley topography. Seismic wave type and incident direction dramatically influenced stress in the face slab, and the extreme stress values and distribution law will vary under oblique wave incidence. The influence of the incident direction on slab stress was particularly apparent when SH-waves arrived from the left bank. Specifically, the extreme stress values in the face slab increased with an increasing incident angle. Interestingly, the locations of the extreme stress values changed mainly along the axis of the dam, and did not exhibit large changes in height. The seismic safety of CFRDs is therefore lower at higher incident angles from an anti-seepage perspective. Therefore, it is necessary to consider both the seismic wave type and incident direction during seismic capacity evaluations of tall CFRDs. 相似文献
15.
Michel Bouchon 《Pure and Applied Geophysics》1996,148(1-2):3-20
We review the application of the discrete wave number method to problems of scattering of seismic waves formulated in terms of boundary integral equation and boundary element methods. The approach is based on the representation of the diffracting surfaces and interfaces of the medium by surface distributions of sources or by boundary source elements, the radiation from which is equivalent to the scattered wave field produced by the diffracting boundaries. The Green's functions are evaluated by the discrete wave number method, and the boundary conditions yield a linear system of equations. The inversion of this system allows the calculation of the full wave field in the medium. We investigate the accuracy of the method and we present applications to the simulation of surface seismic surveys, to the diffraction of elastic waves by fractures, to regional crustal wave propagation and to topographic scattering. 相似文献
16.
针对地下结构抗震分析中应用广泛的波动方法与振动方法,从物理方程和有限元格式出发,明确了两种方法的区别与联系。通过标准数值试验,证明了振动方法是波动方法采用下卧刚性基岩假设和地层水平无限延伸假设,仅考虑SV波垂直向上入射的一种特例。采用波动方法模拟弹性地基,对比振动方法结果,表明弹性地基和刚性地基上地表位移响应和隧道结构内力响应均有显著差异。建议应根据具体场地条件,选择振动或波动方法进行地下结构抗震设计研究。 相似文献