首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到19条相似文献,搜索用时 640 毫秒
1.
地震学的定量研究需要精确的仪器时钟。最近的研究进展表明,可利用背景噪声来检测存在软件/硬件问题的海底地震仪(OBS)或陆上地震仪的台站时钟漂移情况。在稀疏的全球地震台网尺度下,从背景噪声中提取的短周期(20s)瑞利波信号相对较弱,应用时受到限制。位于几内亚湾的持续稳定的26s固定脉动源,辐射出较强的噪声信号,可以被全球台站记录到,因而可以利用它同步加大距离台站间的时钟漂移情况。本文基于噪声互相关方法,我们尝试运用该26s的脉动信号检测非洲、北美和欧洲等地区地震台站的时钟精度。结果发现TAM,OBN台站的时钟在2002~2009年间相对稳定;CCM台站的时钟在2006~2009年间出现了约1s偏差,并且时钟的漂移量不稳定;KOWA台站的时钟漂移从2012年10月的约150s最大上升至2013年1月的约500s。本文将得到的结果与Stehly等(2007)利用背景噪声方法得到的结果、以及远震P波初至到时残差进行了对比分析。利用本文提出的方法,通过与经精确校正过的陆地台站同步,可校正北大西洋海底地震仪的时钟。  相似文献   

2.
云南地区背景噪声特征分析   总被引:3,自引:1,他引:2  
利用云南宽频带数字地震台网46个地震台连续记录的2008~2009年垂直向背景噪声,通过对台站对的背景噪声做互相关计算得到了台站间噪声互相关函数.基于互相关函数正负两个方向特性,分析云南地区5 ~10s、10~20 s、20~40 s共3个频段内高信噪比台站对的方位分布和季节变化特性,发现各个频段的优势方向均有差别,总...  相似文献   

3.
针对气枪主动源监测中相位加权叠加数据绝对到时拾取可能存在较大误差的问题,提出基于台站之间叠加信号波形的相似性,利用台站对波形的互相关得到更准确到时差的策略。在此基础上,将台站对双差地震速度成像方法直接用于台站对到时差数据,以确定地下介质的速度异常。本文利用长江安徽段气枪实验在庐江临时地震台阵接收到的数据进行了测试,发现基于波形互相关得到的到时差数据比绝对到时数据更准确。最后,采用台站对双差地震成像的方法,得到了庐江台阵覆盖区域的地壳三维速度异常模型,继而确定了该地区较大尺度的地下结构分布。  相似文献   

4.
本文选取呼图壁气枪发射台周边流动台记录的2016年6月至2017年12月气枪震源信号和背景噪声信号,分别采用互相关时延检测法和移动窗互谱法研究2016年12月呼图壁6.2级地震前后波速变化特征,得到以下初步结果:呼图壁6.2级地震前后,距6.2级地震60 km的流动台记录的气枪震源信号未发现明显的波速变化,距6.2级地震27 km的固定台石梯子台在6.2级地震前出现了较为明显的波速变化异常,可能与信号传播路径不同有关;流动台记录到的背景噪声信号出现与呼图壁6.2级地震有关的波速异常变化;气枪主要利用体波信号,背景噪声主要利用面波信号,两者射线路径不同可能是导致不同波速变化特征的主要原因。  相似文献   

5.
栾奕  杨宏峰  王宝善 《中国地震》2016,32(2):305-318
宾川气枪地震信号发射台以水库大容量非调制气枪阵列为震源,可以连续不断地激发重复性极高的地震信号。本文利用其2013年的数据,对地下介质进行了观测。由于水库水位的变化对震源波形及远处台站接收到的地震波形会产生影响,因此,为了区分介质变化与震源变化,研究了陆上水库环境下激发气枪震源所产生的地震波形的特征和合适的处理流程。结果表明:1水库水位变化较大时,同一台站记录的地震波形之间的互相关系数过小,不能直接进行叠加处理,需进行震源聚类分析,而震源聚类受水位变化量的控制;2为消除水位的影响,进行了反褶积处理,当震中距小于10km时,对不同水位激发的信号进行叠加再进行反褶积的效果优于直接进行叠加的效果;3通过互相关计算和信噪比分析发现,4个台站的波形变化可能是由地下介质变化引起的。  相似文献   

6.
中国大陆背景噪声成像研究及应用前景   总被引:1,自引:0,他引:1  
对长时间序列的背景地震噪声进行互相关计算可以得到台站间的经验格林函数,这种方法不依赖天然地震及人工震源,仅利用台站记录的背景噪声就能得到地下结构,该方法可以更为便捷地获得地震活动性较低地区的地下构造.随着背景噪声层析成像技术的发展应用,该方法会进一步提高地壳上地幔速度模型的分辨率.本文综述了背景噪声成像技术及其在中国大...  相似文献   

7.
背景噪声成像技术是21世纪以来地震学研究最为重要的突破性进展之一.该方法不依赖于天然地震事件的发生,利用连续地震记录中普遍存在的"背景噪声",通过不同台站对间连续时间信号的互相关来提取经验格林函数并用以进行地下介质结构成像研究.与传统的天然源地震探测手段相比,背景噪声成像技术从随机场源信号中提取介质结构的信息,具有成像...  相似文献   

8.
由于电磁波无法在水中传播,导致海底地震仪(OBS)与全球定位系统(GPS)无法进行实时对钟,因此会产生一定的时钟漂移.而受船时、海况等影响,被动源OBS在回收后往往电量亏损,致使设备回收时并没有完成对钟,无法直接利用对钟前后的时钟漂移量进行线性校正.本文选取中国科学院海洋研究所2016—2017年间在雅浦俯冲带进行的长周期被动源OBS实验所获得的数据,利用背景噪声互相关方法对OBS进行了时间校正.结果发现,各OBS在经过一年左右时间的布放后,时钟漂移量在1~3 s之间,且基本呈线性趋势,将该结果平均分配到每天从而完成线性校正.另外,探讨了时钟的非线性漂移、误差源、参考台站的选取等因素对时钟准确度的影响,为OBS的数据处理进行了有益的探索.  相似文献   

9.
地球背景噪声干涉应用研究的新进展   总被引:1,自引:0,他引:1  
对地震台记录到的长时间的地球背景噪声进行互相关处理,得到的互相关函数可以近似地表征这两个台站之间的格林函数,这种数据处理方法被称为背景噪声干涉.近年来,背景噪声干涉研究在理论和实践上都有了长足进展,并被广泛用于地下波速结构及其演化规律的研究.本文首先简单介绍了背景噪声干涉研究的概念和理论依据,进而重点介绍了针对噪声源性质、互相关函数的波形到时和振幅特性的应用研究.通过对这三个方面研究的回顾,分析总结了该研究领域的新进展及需要解决的问题,并对背景噪声干涉研究的新特点进行了分析和展望.  相似文献   

10.
背景噪声中包含有丰富的地球内部结构信息,可以用来监测地震波速度变化.基于墨西哥中部G.UNM和MX.TLIG两个地震台站2016年4月1日至2018年4月1日的连续波形资料,本文首先对其进行不同频带下的背景噪声互相关处理,然后采用小波变换对获取到的互相关函数进行滤波来解决台站间距过长所引起的互相关函数不稳定问题,最后分别通过Stretching方法和MWCS方法测量得到的走时偏移来提取地震波速度变化.结果表明:利用小波变换能有效提高互相关信噪比和结果精度;采用Stretching方法发现震源区浅部5~10 km的地震波速在地震中上升约0.07%,而在2~5 km的地震波速则有约0.05%的下降趋势;MWCS方法计算结果稳定性稍差,但变化趋势与Stretching结果相同.造成该地震波速变化的主要原因可能是2017年地震所引起的脆性岩层结构破裂.  相似文献   

11.
利用云南省地震台网44个台站记录的2008年1-9月连续波形数据进行互相关计算,得到了台站间的格林函数,并获取对应的频散曲线,据此分析了该地区的区域背景弹性波场的来源及分布.研究发现,该地区的区域背景弹性波场有着明显的方向性,15s信号的总体传播方向是从东南向西北,也就是说主要来自云南省的东南方向,据此推测区域背景弹性...  相似文献   

12.
基于北京市测震台网连续三分量地震计波形数据,计算28个测震台站台基噪声,利用Welch方法计算噪声功率谱密度(PSD),进而计算地震台台基1-20 Hz地动噪声均方根值(RMS)和观测动态范围。结果表明,依照《地震台站观测环境技术要求》,北京市测震台网中有11个Ⅰ类台、9个Ⅱ类台、6个Ⅲ类台、2个Ⅳ类台。通过分析北京市测震台网数字地震台背景噪声水平,为测震台网的规划建设提供数据支持。  相似文献   

13.
We present a new visualization method for human inspection of seismic data called supersonograms, which maximizes the amount of time and stations visible on screen while retaining the possibility to detect short and low-signal to noise ratio (SNR) signals. This visualization approach is integrated into a seismological software suite used in the seismic aftershock monitoring system (SAMS) of Comprehensive Nuclear-Test-Ban Treaty Organization (CTBTO) on-site inspections (OSI) to detect suspicious events eventually representing aftershocks from an underground nuclear explosion (UNE). During an OSI, huge amounts of continuous waveform data accumulate from up to 50 six-channel mini-arrays covering an inspection area of 1,000 square kilometers. Sought-after events can have magnitude as low as $\hbox{M}_{\rm L}\,{-2.0}$ and duration of just a few seconds, which makes it particularly hard to discover them in large, noisy datasets. Therefore, the data visualization is based on nonlinearly scaled, noise-adapted spectrograms, i.e., sonograms, which help to distinguish weak signal energy from stationary background noise. Four single-trace sonograms per mini-array can be combined into supersonograms, since the array aperture is small and sonograms suppress differences of local site noise, allowing an analyst to check array-wide signal coherence quickly. In this paper, we present the supersonograms and the software on the basis of a dataset from a creeping, inhabited landslide in Austria where the same station layout is used as in an OSI. Detected signals are fracture processes in the sedimentary landslide, i.e., slidequakes, with $\hbox{M}_{\rm L}\,{-0.5} \,\hbox{\,to}\,{-2.5}$ between July 2009 and July 2011. These signals are comparable in magnitude and duration to expected weak UNE aftershocks.  相似文献   

14.
用噪声成像方法研究云南地区强震前地震面波速度变化   总被引:3,自引:0,他引:3  
杨文  刘杰  史海霞  周龙泉  苏有锦 《地震》2011,31(3):103-111
本文利用2008年1月至2010年1月云南地震台网46个台站的连续波形资料, 采用背景噪声方法计算云南地区不同台站对之间的面波延迟时间, 通过层析成像方法反演得到不同时间段相同时间窗长的面波波速分布。 根据试验, 将三个月的时间窗长作为云南地区得到稳定信噪比的延迟时间的叠加天数。 结果表明, 不同时间段得到的波速结构具有明显的变化。 这些变化表明: ① 2008年汶川8.0级地震后, 程海断裂带波速增加, 能量积累加剧; ② 2008年攀枝花6.1级地震前攀枝花地区处于速度升高和速度降低的分界带上; ③ 2009年姚安6.0级地震前震中所在区域面波波速升高, 而震后出现降低。 与传统的动态成像相比, 背景噪声方法由于采用固定的台站对, 不同时间段的射线固定, 这样可以减小由于不同时段地震分布不均一和震源定位而引起的误差, 使动态反演结果更加可靠。  相似文献   

15.
Repeating airgun sources are eco-friendly sources for monitoring the changes in the physical properties of subsurface mediums, but their signals decay quickly and are buried in the noises soon after traveling short distances. Stacking waveforms from different airgun shots recorded by a single seismic station (shot stacking) is the most popular technique to detect weak signals from noisy backgrounds, and has been widely used to process the data of Fixed Airgun Signal Transmission Stations (FASTS) in China. However, shot stacking sacrifices the time resolution in monitoring to recover a qualified airgun signal by stacking many shots at distance stations, and also suffers from persistent local noises. In this paper, we carried out several small-aperture seismic array experiments around the Binchuan FAST Station (BCFASTS) in Yunnan Province,China, and applied the array technique to improve airgun signal detection. The results show that seismic array processing combining with shot stacking can suppress seismic noises more efficiently, and provide better signal-to-noise ratio (SNR) and coherent airgun signals with less airgun shots. This work suggests that the array technique is a feasible and promising tool in FAST to increase the time resolution and reduce noise interference on routine monitoring.  相似文献   

16.
介绍了山东数字地震台网基本情况,计算了40个测震台站台基背景噪声,利用Welch方法计算噪声功率谱密度(PSD),进而计算地震台台基1—20 Hz地动噪声均方根值(RMS)和有效动态观测范围。根据计算结果,依照《地震台站观测环境技术要求》,对山东测震数字台网40个参评测震台站进行背景噪声级别分类,并分析不同台站背景噪声水平较低的原因,以期为测震台网的优化建设提供数据支持。  相似文献   

17.
梁建宏  刘杰  杨文  邓菲 《地震》2015,35(1):1-10
本文发展了一种单台检测低频地震事件的方法, 并用其检测2008年汶川MS8.0地震、 2013年芦山MS7.0地震震前的低频事件。 使用汶川地震、 芦山地震前周边的宽频带台站数月的垂直向连续波形, 经过2~8 Hz带通滤波、 窗长为10 s的包络平滑、 窗长为20 min的中值滤波, 去除近场天然地震及远场大震与低频噪声的影响后, 发现这两个大地震前有少数台站在连续数天的时间内, 出现持续时间长(数十分钟到数小时)、 包络中值明显大于背景噪声的现象, 其波形记录及包络特征与非火山震颤(NVT)的波形记录及包络特征具有较好的相似性, 我们认为这是汶川地震和芦山地震前的疑似慢地震事件。 初步应用表明, 本文所用的方法对于从宽频带连续波形资料中提取NVT信号是可行的。  相似文献   

18.
Waveform inversion met severe challenge in retrieving long‐wavelength background structure. We have proposed to use envelope inversion to recover the large‐scale component of the model. Using the large‐scale background recovered by envelope inversion as new starting model, we can get much better result than the conventional full waveform inversion. By comparing the configurations of the misfit functional between the envelope inversion and the conventional waveform inversion, we show that envelope inversion can greatly reduce the local minimum problem. The combination of envelope inversion and waveform inversion can deliver more faithful and accurate final result with almost no extra computation cost compared to the conventional full waveform inversion. We also tested the noise resistance ability of envelope inversion to Gaussian noise and seismic interference noise. The results showed that envelope inversion is insensitive to Gaussian noise and, to a certain extent, insensitive to seismic interference noise. This indicates the robustness of this method and its potential use for noisy data.  相似文献   

19.
We demonstrate that several techniques based on waveform cross-correlation are able to significantly reduce the detection threshold of seismic sources worldwide and to improve the reliability of arrivals by a more accurate estimation of their defining parameters. A master event and the events it can find using waveform cross-correlation at array stations of the International Monitoring System (IMS) have to be close. For the purposes of the International Data Centre (IDC), one can use the spatial closeness of the master and slave events in order to construct a new automatic processing pipeline: all qualified arrivals detected using cross-correlation are associated with events matching the current IDC event definition criteria (EDC) in a local association procedure. Considering the repeating character of global seismicity, more than 90 % of events in the reviewed event bulletin (REB) can be built in this automatic processing. Due to the reduced detection threshold, waveform cross-correlation may increase the number of valid REB events by a factor of 1.5–2.0. Therefore, the new pipeline may produce a more comprehensive bulletin than the current pipeline—the goal of seismic monitoring. The analysts’ experience with the cross correlation event list (XSEL) shows that the workload of interactive processing might be reduced by a factor of two or even more. Since cross-correlation produces a comprehensive list of detections for a given master event, no additional arrivals from primary stations are expected to be associated with the XSEL events. The number of false alarms, relative to the number of events rejected from the standard event list 3 (SEL3) in the current interactive processing—can also be reduced by the use of several powerful filters. The principal filter is the difference between the arrival times of the master and newly built events at three or more primary stations, which should lie in a narrow range of a few seconds. In this study, one event at a distance of about 2,000 km from the main shock was formed by three stations, with the stations and both events on the same great circle. Such spurious events are rejected by checking consistency between detections at stations at different back azimuths from the source region. Two additional effective pre-filters are f–k analysis and F prob based on correlation traces instead of original waveforms. Overall, waveform cross-correlation is able to improve the REB completeness, to reduce the workload related to IDC interactive analysis, and to provide a precise tool for quality check for both arrivals and events. Some major improvements in automatic and interactive processing achieved by cross-correlation are illustrated using an aftershock sequence from a large continental earthquake. Exploring this sequence, we describe schematically the next steps for the development of a processing pipeline parallel to the existing IDC one in order to improve the quality of the REB together with the reduction of the magnitude threshold.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号