共查询到20条相似文献，搜索用时 890 毫秒
1.
In many regions of the world, a bridge will experience multiple extreme hazards during its expected service life. The current American Association of State Highway and Transportation Officials (AASHTO) load and resistance factor design (LRFD) specifications are formulated based on failure probabilities, which are fully calibrated for dead load and nonextreme live loads. Design against earthquake loads is established separately. Design against scour effect is also formulated separately by using the concept of capacity reduction (or increased scour depth). Furthermore, scour effect cannot be linked directly to an LRFD limit state equation, because the latter is formulated using force-based analysis. This paper (in two parts) presents a probability-based procedure to estimate the combined hazard effects on bridges due to truck, earthquake and scour, by treating the effect of scour as an equivalent load effect so that it can be included in reliability-based bridge failure calculations. In Part I of this series, the general principle of treating the scour depth as an equivalent load effect is presented. The individual and combined partial failure probabilities due to truck, earthquake and scour effects are described. To explain the method of including non-force-based natural hazards effects, two types of common scour failures are considered. In Part II, the corresponding bridge failure probability, the occurrence of scour as well as simultaneously having both truck load and equivalent scour load are quantitatively discussed. 相似文献
2.
The current AASHTO load and resistance factor design (LRFD) guidelines are formulated based on bridge reliability,which interprets traditional design safety factors into more rigorously deduced factors based on the theory of probability.This is a major advancement in bridge design specifications.However,LRFD is only calibrated for dead and live loads.In cases when extreme loads are significant,they need to be individually assessed.Combining regular loads with extreme loads has been a major challenge,mainly because the extreme loads are time variables and cannot be directly combined with time invariant loads to formulate the probability of structural failure.To overcome these difficulties,this paper suggests a methodology of comprehensive reliability,by introducing the concept of partial failure probability to separate the loads so that each individual load combination under a certain condition can be approximated as time invariant.Based on these conditions,the extreme loads (also referred to as multiple hazard or MH loads) can be broken down into single effects.In Part Ⅱ of this paper,a further breakdown of these conditional occurrence probabilities into pure conditions is discussed by using a live truck and earthquake loads on a bridge as an example.There are three major steps in establishing load factors from MH load distributions:(1) formulate the failure probabilities;(2) normalize various load distributions;and (3) establish design limit state equations.This paper describes the formulation of the failure probabilities of single and combined loads. 相似文献
3.
The current AASHTO load and resistance factor design (LRFD) guidelines are formulated based on bridge reliability,which interprets traditional design safety factors into more rigorously deduced factors based on the theory of probability.This is a major advancement in bridge design specifications.However,LRFD is only calibrated for dead and live loads.In cases when extreme loads are significant,they need to be individually assessed.Combining regular loads with extreme loads has been a major challenge,mainly because the extreme loads are time variable and cannot be directly combined with time invariant loads to formulate the probability of structural failure.To overcome these difficulties,this paper suggests a methodology of comprehensive reliability,by introducing the concept of partial failure probability to separate the loads so that each individual load combination under a certain condition can be approximated as time invariant.Based on these conditions,the extreme loads (also referred to as multiple hazard or MH loads) can be broken down into single effects.In this paper,a further breakdown of these conditional occurrence probabilities into pure conditions is discussed by using a live truck and earthquake loads on a bridge as an example. 相似文献
4.
目前的AASHTO LRFD桥梁规范主要考虑重力荷载和卡车等活荷载的组合情况,而没有在概率基础上考虑地震等极端荷载的组合问题.包括LRFD在内的很多桥梁抗震规范都是主要考虑地震的作用,甚至设计时不考虑其他荷载的作用,LRFD设计指导手册中在考虑地震等极端荷载时,也只是提到在特殊情况和桥梁比较长的情况下再考虑卡车的作用,... 相似文献
5.
In the U.S.,the current Load and Resistance Factor Design(LRFD) Specifications for highway bridges is a reliability-based formulation that considers failure probabilities of bridge components due to the actions of typical dead load and frequent vehicular loads.Various extreme load effects,such as earthquake and vessel collision,are not considered on the same reliability-based platform.Since these extreme loads are time variables,combining them with frequent,nonextreme loads is a significant challenge.The number of design limit state equations based on these failure probabilities can be unrealistically large and unnecessary from the view point of practical applications.Based on the opinion of AASHTO State Bridge Engineers,many load combinations are insignificant in their states.This paper describes the formulation of a criterion to include only the necessary load combinations to establish the design limit states.This criterion is established by examining the total failure probabilities for all possible time-invariant and time varying load combinations and breaking them down into partial terms.Then,important load combinations can be readily determined quantitatively. 相似文献
6.
Many bridges located in seismic hazard regions suffer from serious foundation exposure caused by riverbed scour. Loss of surrounding soil significantly reduces the lateral strength of pile foundations. When the scour depth exceeds a critical level, the strength of the foundation is insufficient to withstand the imposed seismic demand, which induces the potential for unacceptable damage to the piles during an earthquake. This paper presents an analytical approach to assess the earthquake damage potential of bridges with foundation exposure and identify the critical scour depth that causes the seismic performance of a bridge to differ from the original design. The approach employs the well-accepted response spectrum analysis method to determine the maximum seismic response of a bridge. The damage potential of a bridge is assessed by comparing the imposed seismic demand with the strengths of the column and the foundation. The versatility of the analytical approach is illustrated with a numerical example and verified by the nonlinear finite element analysis. The analytical approach is also demonstrated to successfully determine the critical scour depth. Results highlight that relatively shallow scour depths can cause foundation damage during an earthquake, even for bridges designed to provide satisfactory seismic performance. 相似文献
7.
Load and resistance factor design (LRFD) approach for the design of reinforced soil walls is presented to produce designs with consistent and uniform levels of risk for the whole range of design applications. The evaluation of load and resistance factors for the reinforced soil walls based on reliability theory is presented. A first order reliability method (FORM) is used to determine appropriate ranges for the values of the load and resistance factors. Using pseudo-static limit equilibrium method, analysis is conducted to evaluate the external stability of reinforced soil walls subjected to earthquake loading. The potential failure mechanisms considered in the analysis are sliding failure, eccentricity failure of resultant force (or overturning failure) and bearing capacity failure. The proposed procedure includes the variability associated with reinforced backfill, retained backfill, foundation soil, horizontal seismic acceleration and surcharge load acting on the wall. Partial factors needed to maintain the stability against three modes of failure by targeting component reliability index of 3.0 are obtained for various values of coefficients of variation (COV) of friction angle of backfill and foundation soil, distributed dead load surcharge, cohesion of the foundation soil and horizontal seismic acceleration. A comparative study between LRFD and allowable stress design (ASD) is also presented with a design example. 相似文献
8.
In this work, investigation on the development of local scour around an oblong pier in a 180 degree flume bend is presented. Scour hole can cause failure of the bridge especially during the river floods. In this study, the use of oblong collars for reducing the effects of local scour at a bridge pier is presented together with the time aspect of the scour development. Tests were conducted using one oblong pier in positions of 60degree under one flow conditions. The study was conducted using a physical hydraulic model operated under clear-water conditions in cohesionless bed material. In this study, the time development of the local scour around the oblong pier fitted with and without collar plates was studied. Investigated was the effect of size and elevation collar on the time development of scour and its efficacy at preventing scour at a bridge pier. The time development of the scour hole around the model pier with and without a collar installed was compared with similar studies on bridge piers. The results of the model study indicated that the maximum depth of scour is highly dependent on the experimental duration. It was observed that, as the minimum depth of scour occurs for the square collar at width of 3B placed at elevation of 0.1B below the bed and the size of a collar plate increases, the scour decreases. Measuring depth of scouring based on experimental observation, an empirical relation is developed with regression coefficient 95%. 相似文献
9.
To investigate the seismic performance of hollow reinforced concrete(RC) bridge columns of rectangular cross section under constant axial load and cyclically biaxial bending,five specimens were tested.A parametric study is carried out for different axial load ratios,longitudinal reinforcement ratios and lateral reinforcement ratios.The experimental results showed that all tested specimens failed in the flexural failure mode and their ultimate performance was dominated by flexural capacity,which is represented by the rupture/buckling of tensile longitudinal rebars at the bottom of the bridge columns.Biaxial force and displacement hysteresis loops showed significant stiffness and strength degradations,and the pinching effect and coupling interaction effect of both directions severely decrease the structural seismic resistance.However,the measured ductility coefficient varying from 3.5 to 5.7 and the equivalent viscous damping ratio varying from 0.19 and 0.26 can meet the requirements of the seismic design.The hollow RC rectangular bridge columns with configurations of lateral reinforcement in this study have excellent performance under bidirectional earthquake excitations,and may be considered as a substitute for current hollow RC rectangular section configurations described in the Guideline for Seismic Design of Highway Bridges(JTG/T B02-01-2008).The length of the plastic hinge region was found to approach one sixth of the hollow RC rectangular bridge column height for all specimen columns,and it was much less than those specified in the current JTG/T.Thus,the length of the plastic hinge region is more concentrated for RC rectangular hollow bridge columns. 相似文献
10.
LOCAL SCOUR AROUND BRIDGE ABUTMENTS 总被引：2，自引：0，他引：2
Er. Shri Ram CHAURASIA Pande B.B. LAL Assistant Professor Civil Engineering Department Madan Mohan Malaviya Engineering College Gorakhpur- 《国际泥沙研究》2002,17(1)
1 INTRODUCTION The protrusion of a bridge abutment or a spur dike into the main channel creates a disturbance and obstruction to the otherwise equilibrium state of sediment transportation in an alluvial river. The flow accelerates and separates at the upstream face of the abutment as it moves past the obstacle, creating a vortex trail that moves downstream in a direction approximately perpendicular to the structure. The result is that the bed around the structure is eroded locally. The l… 相似文献
11.
Experimental study has been carried out under a clear-water scour condition to explore the local scour around semi-elliptical model bridge abutments with armor-layer bed, compared with the local scour process around semi-circular abutment. Two types of model bridge abutments, namely semi-elliptical and semi-circular abutments have been used in this experimental study. The model abutments had a ratio of streamwise length of abutment to the length of abutment transverse to the flow of 2 for semi-circular abutments and 3 for semi-elliptical abutments. In total, 50 Experiments have been designed and conducted under different flow conditions such as bed shear velocities, flow depth, and dimensions of bridge abutment model, as well as grain size of the bed material. Based on these experiments, the scour process around bridge abutments has been assessed. The dependence of the equilibrium scour depth of the scour hole on hydraulic variables has been studied. Empirical equation describing the equilibrium scour depth of the scour hole around bridge abutments has been developed. 相似文献
12.
Various methods to control scour around bridge piers have been proposed.In the present study the application of cable or collar and a combination of cable and collar were examined experimentally,as countermeasures against local scouring at a smooth circular bridge pier,close to threshold flow conditions of initiation of uniform sediment motion.The results show that the simultaneous use of cable and collar has high efficiency in reducing the scour depth.The best configuration was found for a cable-pier diameter ratio of 0.15 and thread angle of 15°,in which the scour depth in upstream of the pier reduced to about 53%.In the case of a pier protected with cable and collar the scouring postponed more than pier protected with collar and the rate of scouring is less than in pier protected with collar.These advantages can reduce the risk of pier failure when the duration of flood is short. The results indicate that the scour reduction increases as the cable diameter increased and the thread angle decreased. 相似文献
13.
This study developed a finite element method with the effect of soil–fluid–structure interaction to calculate bridge natural frequencies. The finite element model includes bridge girders, piers, foundations, soil, and water. The effective mass above the soil surface was then used to find the first natural frequency in each direction. A field experiment was performed to validate that the natural frequencies calculated using the proposed finite element method had acceptable accuracy. The calculated natural frequencies with the fluid–structure interaction effect are always smaller than those without this effect. However, the frequency change due to the fluid effect is not obvious, so using the soil–structure interaction model is accurate enough in the bridge natural frequency analysis. The trend of the frequency decreases with the increase of the scour depth, but the curve is not smooth because of non-uniform foundation sections and layered soils. However, when the scour depth is such that pile cap is exposed, the changes in natural frequency with the scour depth are more obvious, and this is useful for measurement of the depth using bridge natural frequencies. 相似文献
14.
In the current study, 108 flume experiments with non-uniform, cohesionless sediments have been done to investigate the local scour process around four pairs of side-by-side bridge piers under both open channel and ice-covered flow conditions. Similar to local scour around bridge piers under open channel conditions and a single bridge pier, it was observed in the experiments that the maximum scour depth always occurred at the upstream face of the pier under ice-covered conditions. Further, the smaller the pier size and the greater the spacing distance between the bridge piers, the weaker the horseshoe vortices around the bridge piers, and, thus, the shallower the scour holes around them. Finally, empirical equations were developed to estimate the maximum scour depth around two side-by-side bridge piers under both open channel and ice-covered flow conditions. 相似文献
15.
Characterization of horseshoe vortex in a developing scour hole at a cylindrical bridge pier 总被引：1，自引：0，他引：1
Since local scour at bridge piers in rivers and estuaries is a major cause of bridge failure, estimation of the maximum local scour depth is of great importance to hydraulic and coastal engineers. Although numerous studies that focus on scour-depth prediction have been done and published, understanding of the flow and turbulence characteristics of the horseshoe vortex that drives the scour mechanism in a developing scour hole still is immature. This study aims to quantify the detailed turbulent flow field in a developing clear-water scour hole at a circular pier using Particle Image Velocimetry (PIV). The distributions of velocity fields, turbulence intensities, and Reynolds shear stresses of the horseshoe vortex that form in front of the pier at different scour stages (t=0, 0.5, 1, 12, 24, and 48 h) are presented in this paper. During scour development, the horseshoe vortex system was found to evolve from one initially small vortex to three vortices. The strength and size of the main vortex are found to increase with increasing scour depth. The regions of both the maximum turbulence intensity and Reynolds shear stress are found to form at a location upstream of the main vortex, where the large turbulent eddies have the highest possibility of occurrence. Results from this study not only provide new insight into the complex flow-sediment interaction at bridge piers, but also provide valuable experimental databases for advanced numerical simulations. 相似文献
16.
Large woody debris(LWD) reduces the flow area,deviate the flow and increases the velocity in correspondence of the bridge pier,therefore increases the maximum scour hole depth and accelerates sediment removal.Logs and drifts accumulated on bridge piers are of different dimensions.According to logs characteristics and river morphology,drift accumulations can either extend downstream the bridge pier or they can accumulate totally upstream.This paper aims to analyze the effect of drift accumulation planimetry on bridge pier scour.The experimental investigation has been carried out at the PITLAB hydraulic centre of Civil Engineering Department,University of Pisa,Italy.Drift accumulation was characterized by different relative longitudinal lengths,flow area occlusions,length of longitudinal drift and downstream planimetrical positions relative to the pier center.The experimental investigation has been carried out in clear-water conditions.Several pier sizes,channel widths and sediment materials have been tested.Maximum scour hole in presence of drift accumulation have been compared to the maximum scour hole for an isolated pier.Finally,data were compared with previous literature findings,which highlight the effect of the downstream extension of drift accumulation on bridge pier scour.New relationships have been proposed to predict the effect of drift accumulation on bridge pier scour,both in terms of relative maximum scour and temporal scour evolution. 相似文献
17.
Yee Meng CHIEW 《国际泥沙研究》1992,(1)
This paper examines the effect of dune migration on local scour around bridge piers. Experiments show that local scour depths fluctuate in response to the translation of dunes past the scour hole. The scour depths measured in a model study conducted in live-bed conditions contain both scour due to the pier and that due to dunes. The con' tribution from scour due to the dunes may form a significant fraction of the total scour depth measured in model investigations. Therefore, it is imperative to separate these two components of scour for analysis and comparison. The study proposes that an equilibrium or time-average scour depth normalized using pier diameter be used for analysis, and the contribution from dunes to the total scour depth be added independently. Dune size, in the absence of field or measured data, may be estimated using published predictive curves. Comparisons between computed and measured scour depths show a good correlation, and 90% of all the data tested fall within a scatter of 15%. 相似文献
18.
19.
冲刷造成桩周土体的剥蚀将会削弱土体对桩基的侧向支撑能力,冲刷效应会对桥梁桩基的地震易损性产生影响,因此有必要对冲刷和地震共同作用下桥梁桩基的易损性进行研究。利用SAP2000软件建立三维桥梁有限元模型,通过非线性时程分析得到桥梁桩基地震响应峰值。采用概率性地震需求分析方法,建立不同冲刷深度下桥梁桩基地震易损性模型,在地震易损性函数假设为对数正态分布函数的基础上,通过回归分析得到概率模型中的参数,进而得到不同冲刷深度下桥梁桩基在不同破坏状态所对应的地震易损性曲线,并分析冲刷深度对桩基破坏概率的影响。研究结果表明:随着冲刷深度的增加,桥梁桩基在地震作用下的破坏概率显著增加。 相似文献
20.
本文用确定性和随机概率的方法研究了工桥墩台和小跨拱桥在恒载及活载（包括地震效应）作用下决定某截面上的偏心距，以便使其在设计规范规定的限度时所能通过的活载最大等级是什么，由于地震随机性强烈，故基于概率理论的结构可靠性方法优于确定性的方法，但在本文中的结果显示，这两种方法的最终结果十分接近。 相似文献