首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 46 毫秒
1.
An experiment was conducted to determine if biodegradation of trichloroethylene (TCE) can occur in previously uncontaminated ground water in saturated fractured saprolite (highly weathered material derived from sedimentary rocks). Two undisturbed columns (0.23 m diameter by 0.25 m long) of fractured saprolite were collected from approximately 2 m depth at an uncontaminated site on the Oak Ridge Reservation, Oak Ridge, Tennessee. Natural, uncontaminated ground water from the site, which was degassed and spiked with dissolved phase TCE, was continuously pumped through one column containing the natural microbial communities (the biotic column). In a second column, the microorganisms were inhibited and the dissolved phase TCE was added under aerobic conditions (dissolved oxygen conditions > 2 ppm). In effluent from the biotic column, reducing conditions rapidly developed and evidence of anaerobic biodegradation of TCE, by the production of cDCE, first appeared approximately 31 days after addition of TCE. Reductive dechlorination of TCE occurred after iron-reducing conditions were established and about the same time that sulfate reduction began. There was no evidence of methanogenesis. Analyses using polymerase chain reaction with specific primers sets detected the bacteria Geothrix, Geobacter, and Desulfococcus-Desulfonema-Desulfosarcina in the effluent of the biotic column, but no methanogens. The presence of these bacteria is consistent with iron- and sulfate-reducing conditions. In the inhibited column, there were no indicators of TCE degradation. Natural organic matter that occurs in the saprolite and ground water at the site is the most likely primary electron donor for supporting reductive dechlorination of TCE. The relatively rapid appearance of indicators of TCE dechlorination suggests that these processes may occur even in settings where low oxygen conditions occur seasonally due to changes in the water table.  相似文献   

2.
In view of the increasing demand on ground water supplies in the northeastern United States, it is imperative to develop appropriate methods to geophysically characterize the most widely used sources of ground water in the region: shallow unconfined aquifers consisting of well-sorted, stratified glacial deposits laid down in bedrock valleys and channels. The gravity method, despite its proven value in delineating buried bedrock valleys elsewhere, is seldom used by geophysical contractors in this region. To demonstrate the method's effectiveness for evaluating such aquifers, a pilot study was undertaken in the Palmer River Basin in southeastern Massachusetts. Because bedrock is so shallow beneath this aquifer (maximum depth is 30 m), the depth-integrated mass deficiency of the overlying unconsolidated material was small, so that the observed gravity anomaly was on the order of 1 milligal (mGal) or less. Thus data uncertainties were significant. Moreover, unlike previous gravity studies elsewhere, we had no a priori information on the density of the sediment. Under such circumstances, it is essential to include model constraints and weighted least-squares in the inversion procedure. Among the model constraints were water table configuration, bedrock outcrops, and depth to bedrock from five water wells. Our procedure allowed us to delineate depth to bedrock along a 3.5 km profile with a confidence interval of 1.8 m at a nominal depth of 17 m. Moreover, we obtained a porosity estimate in the range of 39% to 44%. Thus the gravity method, with appropriate refinements, is an effective tool for the reconnaissance of shallow unconfined aquifers.  相似文献   

3.
The architecture of the critical zone includes the distribution, thickness, and contacts of various types of slope deposits and weathering products such as saprolite and weathered bedrock resting on solid bedrock. A quantitative analysis of architecture is necessary for many model‐driven approaches used by pedologic, geomorphic, hydrologic or biologic studies. We have used electrical resistivity tomography, a well‐established geophysical technique causing minimum surficial disturbance, to portray the subsurface electrical resistivity differences at three study sites (Green Lakes Valley; Gordon Gulch; Betasso) at the Boulder Creek Critical Zone Observatory (BcCZO). Possible limitations of the technique are discussed. Interpretation of the specific resistivity values using natural outcrops, pits, roadcuts and drilling data as ground truth information allows us to image the critical zone architecture of each site. Green Lakes Valley (3700 MASL), a glacially eroded alpine basin, shows a rather simple, split configuration with coarse blockfields and sediments, partly containing permafrost above bedrock. The critical zone in Gordon Gulch (2650 MASL), a montane basin with rolling hills, and Betasso (1925 MASL), a lower montane basin with v‐shaped valleys, is more variable due to a complex Quaternary geomorphic history. Boundaries between overlying stratified slope deposits and saprolite were identified at mean depths of 3.0 ± 2.2 m and 4.1 ± 3.6 m in the respective sites. The boundary between saprolite and weathered bedrock is deeper in Betasso at 5.8 ± 3.7 m, compared with 4.3 ± 3.0 m in Gordon Gulch. In general, the data are consistent with results from seismic studies, but electrical resistivity tomography documents a 0.5–1.5 m shallower critical zone above the weathered bedrock on average. Additionally, we document high lateral variability, which results from the weathering and sedimentation history and seems to be a consistent aspect of critical zone architecture within the BcCZO. Copyright © 2013 John Wiley & Sons, Ltd.  相似文献   

4.
For health, economic, and aesthetic reasons, allowable concentrations (as suggested by the United States Environmental Protection Agency) of the secondary contaminants iron (Fe) and manganese (Mn) found present in drinking water are 0.3 and 0.05 mg/L, respectively. Water samples taken from private drinking wells in rural communities within Buncombe County, North Carolina contain concentrations of these metals that exceed secondary water quality criteria. This study predicted the spatial distribution of Fe and Mn in the county, and evaluated the effect of site environmental factors (bedrock geology, ground elevation, saprolite thickness, and drinking water well depth) in controlling the variability of Fe and Mn in groundwater. A statistically significant correlation between Fe and Mn concentrations, attributable to bedrock geology, was identified. Prediction models were created using ordinary kriging and cokriging interpolation techniques to estimate the presence of Fe and Mn in groundwater where direct measurements are not possible. This same procedure can be used to estimate the trend of other contaminants in the groundwater in different areas with similar hydrogeological settings.  相似文献   

5.
In this paper a characterization of seismic site response is proposed, taking into consideration geo-morphological conditions, geotechnical and geophysical parameters such as slope, average shear-wave velocity, maximum expected acceleration on bedrock, depth of ground water table. An empirical relationship is presented between these parameters and applied, with the objective of determining ground motion amplification coefficients to be used in specific programs of land use or town planning dedicated to the mitigation of seismic risk.  相似文献   

6.
The measurement of wavetilt is diagnostic for determining the electrical characteristics of the upper layers of the ground at VLF and LF frequency ranges. Theoretical and field studies have indicated that electric wavetilt using the transverse magnetic (TM) waves detects lateral inhomogeneities virtually instantly as abrupt changes in electrical properties are encountered. Theoretical studies have also indicated that magnetic wavetilt measurements using transverse electric (TE) waves are superior to electric wavetilts for such purposes. An experimental survey was conducted at two locations near Atikokan, Ontario, to verify the theoretical predictions. The survey area, forming a part of a large granitic pluton, was mapped earlier by various geophysical techniques, including the ground VLF-EM method, to detect weak conductors formed either by the presence of fractures in the bedrock filled with water and/or clay, or overburden filling bedrock depressions. A small, multi-turn, horizontal loop was used during the survey as the transmitter to generate TE waves at eleven frequencies from 10.7 to 58.5 kHz. The magnetic wavetilt measurements detected all previously known conductors at the two locations. In addition, the survey detected several weak conductors that were missed by the VLF survey. Thus, the survey indicated the usefulness of magnetic wavetilt results for detection of weak conductors at shallow depths, which may have application in engineering geophysical surveys. The multi-frequency wavetilt data also provided some indications of the depth and depth extent of such conductors.  相似文献   

7.
The laterites in Burundi, which are formed by weathering of ultrabasic rocks, show a complete profile with the following horizons: canga, the ferruginous crust capping, ferralite, consisting essentially of iron hydroxides, and saprolite, which contains a large quantity of hydrosilicate minerals. Nickel bearing minerals occur in the saprolite and the lower portion of ferralite. Resistivity well-logging and resistivity sounding indicated that the electrical properties of rocks depend upon their composition: Canga and ferralite showed high resistivities of 6,500 Ωm and 800 Ωm, respectively. The resistivity of saprolite was found to be much lower, between 10 Ωm and 20 Ωm. The laterite is underlain by resistive peridotite. The chargeability of saprolite was found to be lower than that of the upper horizons and the bedrock. Electrolytic conductivity of laterite, which depends on the geometry of the deposit, was found to be low, because the laterite contains moisture and ground water, which are highly resistive. The relatively high conductivity of saprolite is caused by nickeliferous hydrosilicates, which exhibit the electrical properties of clay minerals, with an apparent maximum conductivity of 0.25 S/m. The conductivity of saprolite corresponds to a concentration between 30% and 50% of conductive silicate minerals distributed in the pore space of deposit. A nickel enrichment of up to 6% was estimated from the resistivity of the saprolite. Prospecting for laterites by electrical sounding showed that the development of laterite horizons in a nickel deposit correlates with the surface morphology of weathered ultrabasic massif. Thus the method can be used in preliminary exploration of such deposits.  相似文献   

8.
  相似文献   

9.
Seaton WJ  Burbey TJ 《Ground water》2005,43(3):301-313
The Blue Ridge Province contains ubiquitous northeast-southwest-trending thrust faults or smaller thrust "slivers" that greatly impact the nature and character of ground water flow in this region. Detailed investigations at a field site in Floyd County, Virginia, indicate that high-permeability zones occur in the brittle crystalline rocks above these thrust faults. Surface and borehole geophysics, aquifer tests, and chlorofluorocarbon and geochemical data reveal that the shallow saprolite aquifer is separated from the deeper fault-zone aquifer by a low-fracture permeability bedrock confining unit, the hydraulic conductivity of which has been estimated to be six orders of magnitude less than the conductivity of the fault zones at the test site. Within the Blue Ridge Province, these fault zones can occur at depths of 300 m or more, can contain a significant amount of storage, and yield significant quantities of water to wells. Furthermore, it is expected that these faults may compartmentalize the deep aquifer system. Recharge to and discharge from the deep aquifer occurs by slow leakage through the confining unit or through localized breach zones that occur where quartz accumulated in high concentrations during metamorphism and later became extensively fractured during episodes of deformation. The results of this investigation stress the importance of thrust faults in this region and suggest that hydrogeologic models for the Blue Ridge Province include these ancient structural features. Faults in crystalline-rock environments may not only influence the hydrology, they may dominate the flow characteristics of a region.  相似文献   

10.
Deeply weathered crystalline rock aquifer systems comprising unconsolidated saprolite and underlying fractured bedrock (saprock) underlie 40% of sub-Saharan Africa. The vulnerability of this aquifer system to contamination, particularly in rapidly urbanizing areas, remains poorly understood. In order to assess solute and viral transport in saprolite derived from Precambrian gneiss, forced-gradient tracer experiments using chloride and Escherichia coli phage ΦX174 were conducted in southeastern Uganda. The bacteriophage tracer was largely unrecovered; adsorption to the weathered crystalline rock matrix is inferred and enabled by the low pH (5.7) of site ground water and the bacteriophage's relatively high isoelectric point (pI = 6.6). Detection of the applied ΦX174 phage in the pumping well discharge at early times during the experiment traces showed, however, that average ground water flow velocities exceed that of the inert solute tracer, chloride. This latter finding is consistent with observations in other hydrogeological environments where statistically extreme sets of microscopic flow velocities are considered to transport low numbers of fecal pathogens and their proxies along a selected range of linked ground water pathways. Application of a radial advection-dispersion model with an exponentially decaying source term to the recovered chloride tracer estimates a dispersivity (α) of 0.8 ± 0.1 m over a distance of 4.15 m. Specific yield (Sy) is estimated to be 0.02 from volume balance calculations based on tracer experiments. As single-site observations, our estimates of saprolite Sy and α are tentative but provide a starting point for assessing the vulnerability of saprolite aquifers in sub-Saharan Africa to contamination and estimating quantitatively the impact of climate and abstraction on ground water storage.  相似文献   

11.
The conversion of bedrock to regolith marks the inception of critical zone processes, but the factors that regulate it remain poorly understood. Although the thickness and degree of weathering of regolith are widely thought to be important regulators of the development of regolith and its water‐storage potential, the functional relationships between regolith properties and the processes that generate it remain poorly documented. This is due in part to the fact that regolith is difficult to characterize by direct observations over the broad scales needed for process‐based understanding of the critical zone. Here we use seismic refraction and resistivity imaging techniques to estimate variations in regolith thickness and porosity across a forested slope and swampy meadow in the Southern Sierra Critical Zone Observatory (SSCZO). Inferred seismic velocities and electrical resistivities image a weathering zone ranging in thickness from 10 to 35 m (average = 23 m) along one intensively studied transect. The inferred weathering zone consists of roughly equal thicknesses of saprolite (P‐velocity < 2 km s?1) and moderately weathered bedrock (P‐velocity = 2–4 km s?1). A minimum‐porosity model assuming dry pore space shows porosities as high as 50% near the surface, decreasing to near zero at the base of weathered rock. Physical properties of saprolite samples from hand augering and push cores are consistent with our rock physics model when variations in pore saturation are taken into account. Our results indicate that saprolite is a crucial reservoir of water, potentially storing an average of 3 m3 m?2 of water along a forested slope in the headwaters of the SSCZO. When coupled with published erosion rates from cosmogenic nuclides, our geophysical estimates of weathering zone thickness imply regolith residence times on the order of 105 years. Thus, soils at the surface today may integrate weathering over glacial–interglacial fluctuations in climate. Copyright © 2013 John Wiley & Sons, Ltd.  相似文献   

12.
An Erratum has been published for this article in Earth Surface Processes and Landforms 28(13) 2003, 1491. Granite domes, boulders and knobs buried within saprolite have been detected beneath lateritic weathering landsurfaces using 2D electrical resistivity tomography (ERT). This technique provides a valuable means of mapping the bedrock topography and the regolith structures underneath landsurfaces, as it is intrinsically very sensitive to the electrical properties of superimposed pedological, hydrological and geological layers, allowing the determination of their relative geometry and spatial relationships. For instance, 2D inverse electrical resistivity models including topographic data permit the de?nition of lithostratigraphic cross‐sections. It shows that resistive layers, such as the more or less hardened ferruginous horizons and/or the bedrock, are generally well differentiated from poorly resistive layers, such as saprolite, including water‐saturated lenses, as has been corroborated by past and actual borehole observations. The analysis of the 2D geometrical relations between the weathering front, i.e. the bedrock topography, and the erosion surface, i.e. the landsurface topography, documents the weathering and erosion processes governing the development of the landforms and the underlying structures, thus allowing the etching hypothesis to be tested. The in?ltration waters are diverted by bedrock protrusions, which behave as structural thresholds compartmentalizing the saprolite domain, and also the regolith water table, into distinct perched saturated subdomains. The diverted waters are thus accumulated in bedrock troughs, which behave like underground channels where the saprolite production rate may be enhanced, provided that the water drainage is ef?cient. If the landsurface topography controls the runoff dynamics, the actual bedrock topography as depicted by ERT imaging in?uences the hydrodynamics beneath the landsurface. In some way, this may control the actual weathering rate and the shaping of bedrock protrusions as granite domes and knobs within thick saprolite, before their eventual future exposure. Copyright © 2003 John Wiley & Sons, Ltd.  相似文献   

13.
Warner KL 《Ground water》2001,39(3):433-442
The lower Illinois River Basin (LIRB) covers 47,000 km2 of central and western Illinois. In the LIRB, 90% of the ground water supplies are from the deep and shallow glacial drift aquifers. The deep glacial drift aquifer (DGDA) is below 152 m altitude, a sand and gravel deposit that fills the Mahomet Buried Bedrock Valley, and overlain by more than 30.5 m of clayey till. The LIRB is part of the USGS National Water Quality Assessment program, which has an objective to describe the status and trends of surface and ground water quality. In the DGDA, 55% of the wells used for public drinking-water supply and 43% of the wells used for domestic drinking water supply have arsenic concentrations above 10 micrograms/L (a new U.S. EPA drinking water standard). Arsenic concentrations greater than 25 micrograms/L in ground water are mostly in the form of arsenite (AsIII). The proportion of arsenate (AsV) to arsenite does not change along the flowpath of the DGDA. Because of the limited number of arsenic species analyses, no clear relations between species and other trace elements, major ions, or physical parameters could be established. Arsenic and barium concentrations increase from east to west in the DGDA and are positively correlated. Chloride and arsenic are positively correlated and provide evidence that arsenic may be derived locally from underlying bedrock. Solid phase geochemical analysis of the till, sand and gravel, and bedrock show the highest presence of arsenic in the underlying organic-rich carbonate bedrock. The black shale or coal within the organic-rich carbonate bedrock is a potential source of arsenic. Most high arsenic concentrations found in the DGDA are west and downgradient of the bedrock structural features. Geologic structures in the bedrock are potential pathways for recharge to the DGDA from surrounding bedrock.  相似文献   

14.
In this study, we used an archive of borehole logs from the British Geological Survey to collect information on the spatial structure of weathering that extends from the surface to competent bedrock across the Triassic Sherwood Sandstone Group outcrop (750 km2), in the East Midlands, UK. The borehole logs were used to estimate the thickness of the soil (n = 280) and soil and saprolite (S&S) to competent rock (n = 500). The weathering profile of the sandstone consisted of soil (median thickness ～ 1·5 m) overlying a transition zone of compacted and weakly cemented weathered sandstone saprolite over bedrock. Topographic analysis using a NEXTMAP 5 m × 5 m digital elevation model (DEM) revealed no significant relationships between slope properties (relief, flow length, flow accumulation or slope angle) and soil or S&S thickness. A weak, but statistically significant correlation was found between the thickness of the soil and S&S (rs = 0·25, p < 0·001, n = 192). The variation in soil thickness may be related to changes in current and historic and land‐use, variation in sandstone properties and the influence of glacial/peri‐glacial processes. The thickness of the saprolite was more variable towards the southern part of the study area, where it increased to a maximum 40 m. We hypothesize and provide evidence that the greater weathering thickness is related to the occurrence of increased faulting in this part of the study region, allowing increased access to meteoric waters. A possible source of increased water supply is meltwater from Quaternary ice sheets; the overburden of ice may have increased sub‐glacial pore water pressure, with the fractures and faults acting as a drainage system for the removal of dissolved weathering products. British Geological Survey © NERC 2010  相似文献   

15.
Shear wave velocity–depth information is required for predicting the ground motion response to earthquakes in areas where significant soil cover exists over firm bedrock. Rather than estimating this critical parameter, it can be reliably measured using a suite of surface (non-invasive) and downhole (invasive) seismic methods. Shear wave velocities from surface measurements can be obtained using SH refraction techniques. Array lengths as large as 1000 m and depth of penetration to 250 m have been achieved in some areas. High resolution shear wave reflection techniques utilizing the common midpoint method can delineate the overburden-bedrock surface as well as reflecting boundaries within the overburden. Reflection data can also be used to obtain direct estimates of fundamental site periods from shear wave reflections without the requirement of measuring average shear wave velocity and total thickness of unconsolidated overburden above the bedrock surface. Accurate measurements of vertical shear wave velocities can be obtained using a seismic cone penetrometer in soft sediments, or with a well-locked geophone array in a borehole. Examples from thick soil sites in Canada demonstrate the type of shear wave velocity information that can be obtained with these geophysical techniques, and show how these data can be used to provide a first look at predicted ground motion response for thick soil sites.  相似文献   

16.
本文运用高密度电法对宁夏西吉县西南山区典型的黄土地震滑坡进行了探测,并结合钻探资料进行验证分析,目的是查明滑坡区域的地层结构、黄土厚度、基岩埋深、富水地段以及空间展布等特征.结果表明:电阻率参数能够很好的反应研究区的地层分布特征,表层疏松干燥的黄土为高阻反映,随着埋深增加,含水量较大的黄土呈现出低阻反映,在黄土与泥岩接触带饱水区呈现低阻反映;滥泥河流域典型的黄土梁斜坡具有阳坡黄土沉积薄、富水层薄、基岩埋深浅的特征,而在阴坡则表现出黄土沉积厚、富水层厚、基岩埋深大的特征.探测结果可有效的应用于黄土地震滑坡的勘察,为进一步开展黄土地震滑坡的成因机理和防治研究提供参考数据.  相似文献   

17.
The simultaneous transfer of pore fluid and vapour was studied in the unsaturated shallow subsurface of a Plio-Pleistocene marine mudstone badland slope in southwestern Taiwan during the dry season using field monitoring data and numerical simulations. Data from field monitoring show mass-basis water contents of ~0.05 to ~0.10 that decrease towards the unsaturated ground surface and were invariant during the middle part of the dry season, except for daily fluctuations. In addition, the observed daily fluctuations in water content correlate with fluctuations in bedrock temperature, especially at depths of 2.5–5.0 cm. Periodic increases in water content occurred most notably during the day, when the bedrock temperature showed the greatest increase. Water contents then decreased to the previous state as bedrock temperature decreased during the night. Calculated vapour fluxes within the mudstone during the day increased up to 6 × 10−6–1 × 10−5 kg m−2 s−1, deriving a 0.01–0.02 increase in mass-basis water content at 2.5 cm depth for a 12-h period. This agrees with field monitoring data, suggesting that increases in water content occurred due to vapour intrusions into the bedrock. Pore water electrical conductivity (EC) showed periodic variations due to vapour intrusion, and gradually increased between the ground surface and depths of 2.5–5.0 cm. In contrast, pore water EC gradually decreased between 15 and 40 cm depth. Calculated water fluxes at depths of 2.5–40.0 cm varied from −4 × 10−6 to −2 × 10−9 kg m−2 s−1. These fluxes generated an increase in solute concentrations at the ground surface, with negative values of water flux indicating an upwards movement of water towards the surface. We show that the increase in solute content due to solute transfer from depth is highly dependent on variations in water flux with depth. © 2020 John Wiley & Sons, Ltd.  相似文献   

18.
Resistivity investigations were carried out on an elementary watershed in SW Cameroon, firstly to assess the applicability of direct-current (DC) resistivity methods to solve various pedological problems in intertropical regions, and subsequently to determine the relationships between electrical resistivities and pedological properties of lateritic soil systems. The survey included measurements in pits with a small Wenner fixed-spacing array (SWA), vertical electrical soundings (VES) and vertical electrical “quick soundings” (VEQS) both using the Schlumberger configuration. The VES data were interpreted using a conventional multilayer inversion program to obtain best-fit models. Constraints to the interpretation of these data were provided by SWA and pedological information from existing observation pits. The results of the interpretation reveal five distinct geoelectrical layers overlying a resistive bedrock. The first is a thin organo-mineral upper layer with low resistivities in the range 250–450 Ωm. The second layer corresponds to micro-aggregated clayey materials and is more resistive (1300–1800 Ωm). The third represents the main part of ferruginous materials and is even more resistive (2000–4500 Ωm). The fourth corresponds to unsaturated saprolite and the last to saturated saprolite (ground water) with resistivities ranging from 800 to 1500 Ωm and from 150 to 250 Ωm, respectively. Estimates of soil volumes for the entire study area were obtained from VEQS interpretations. Most of the soil cover corresponds to saprolite (74%, being saturated by ground water), while topsoil and ferruginous materials represent 14 and 12%, respectively. Finally, geophysical results based upon 1-D inversion provide a satisfactory approximation of the various lateritic components' 3-D geometry over the watershed. The study provides original quantitative results concerning the behaviour of intertropical soil systems as well as some geomorphological keys for soil mapping at a regional scale.  相似文献   

19.
Fracture Density Distributions and Well Yields in Coastal Maine   总被引：1，自引：0，他引：1  
Understanding the distribution of water-bearing fractures in crystalline rock is an important component in evaluating the availability and vulnerability of water resources throughout the northeastern U.S. The State of Maine requests well drillers to report estimates of fracture depths and fracture yields for all bedrock wells drilled in the state. Using these data we analyze fracture-depth and fracture-yield data from 227 bedrock wells in coastal Maine in order to understand how fracture locations and yields are distributed with depth. Numerical simulations and statistical tests show that it is not possible to infer how fractures are distributed with depth: fracture depths are consistent with several distributions, including uniform fracture density with depth. In order to understand how fracture yield varies with depth, we group yield data into 50 foot depth intervals and compare distributions in each interval using nonparametric statistical tests. These tests show that the distribution of fracture yield in different depth intervals are statistically equivalent. These results imply that there is no empirical justification for limiting well depth when drilling for water resources in fractured bedrock in coastal Maine.  相似文献   

20.
基岩地震动参数与震级和距离的关系   总被引：3，自引：1，他引：3       下载免费PDF全文
关于强地震对结构的作用,应当考虑随时间变化的地面运动的全过程。 这个过程的统计特征是由震级、中间介质及地表土层的特性决定的。 因为现在已经有了从基岩运动推算地表运动的可靠方法,所以搞清基岩运动的特征并由此对基岩运动的过程作出估计,显得特别重要。 本文对美国27个基岩台上的强震记录的反应普以及几个最大值与震级和震源距离的关系进行了统计分析,找到它们的关系。从这些关系出发,对指定的震级和震源距离的基岩,可以估计它的运动特征,并人工造成一组运动过程。   相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号