共查询到20条相似文献，搜索用时 46 毫秒
1.
底泥覆盖对浅水湖泊藻源性湖泛的控制模拟 总被引：1，自引：1，他引：0
湖泛的发生与湖泊底部氧化还原条件和致黑致臭物充足供给直接相关.利用黄土和细沙对太湖湖泛易发区(月亮湾)底泥进行覆盖,模拟在湖泛可形成条件下,底泥-水体系及其界面主要物化性质与感官变化过程.结果表明:0.5 cm黄土和1.0 cm细沙的覆盖,从水色和嗅味半定量角度达到了对湖泛黑臭的控制,与对照组相比,覆盖组底泥间隙水中主要致黑物Fe2+浓度仅为对照组的1/3,主要致臭物甲硫醇和二甲基三硫醚等浓度则不到50%.进一步分析底部水体和底泥性质发现:经覆盖处理底部水体的溶解氧浓度提高近1倍,氧化还原电位基本处于250 m V以上水平,覆盖层1 cm左右表层氧化还原电位和p H均远高于对照底泥.以黄土为主的底泥覆盖,主要因阻隔了下层底泥中物质迁移供给和对厌氧微生物参与的控制,以及黄土本身性质对湖底物化环境的影响等,在藻体大量聚集和死亡的水柱环境中,较好地阻止了致黑致臭物的形成,从而较有效控制湖泛的发生. 相似文献
2.
藻源性湖泛水体显黑颗粒的元素形态分析与鉴定 总被引：6，自引：6，他引：0
湖泛现象是我国超富营养化浅水湖泊面临的最严峻环境问题之一,水体发黑、发臭是湖泛水体最显著和基本的物理特征.针对太湖湖泛显黑颗粒缺乏从元素形态直接给出证据的问题,针对室内模拟藻体和沉积物存在下形成的湖泛水体,采用多种图谱分析技术,对厌氧截留分离的显黑颗粒物质及其化学组成和元素形态进行了分析鉴定.扫描电镜-X射线能谱分析与荧光光谱分析表明:湖泛水体显黑颗粒物质以藻类残体和悬浮沉积物颗粒物为主,其组成元素以C、O、Si为主;与未发生湖泛的对照样相比,湖泛水体显黑颗粒物样品中具有更高的Fe、S含量.X射线光电子能谱Fe、S微区分析进一步表明:湖泛显黑颗粒物样品中Fe主要以Fe(Ⅱ)的形式存在、S则以还原态S2-的形式赋存,两者具有共同化合成Fe S的充要条件.因此,缺氧厌氧条件下,湖泛水体的显黑物质组成是Fe S,它可由水体中Fe2+和ΣS2-通过化学共沉淀形成,并主要通过吸附于悬浮颗粒物之上而使得整个水柱呈现黑色,指示湖泛的暴发过程和维持状态. 相似文献
3.
水草腐烂引发的黑臭水体应急处置技术研究 总被引：3，自引：0，他引：3
水草腐烂加速水体耗氧和水体还原性物质的溶出进程,在夏、秋季高温条件下极易引发局部水体黑臭.以太湖沉水植物优势种马来眼子菜(Potamogeton malaianus)、苦草(Vallisneria natans)及浮叶植物优势种莕菜(Nymphoides peltatum)为受试材料,利用太湖原位底泥培养模拟水草腐烂形成的黑臭水体,考察不同的环境材料处置方式(壳聚糖(CTS)、聚合氯化铝(PAC)、聚丙烯酰胺(PAM)、CTS+PAC和PAC+PAM)对黑臭水体浊度、溶解氧浓度、挥发性硫化物等黑臭水体特征污染物的絮凝沉降规律及去除机理.结果表明:(1)絮凝处理24 h后,CTS+PAC组合对黑臭水体的浊度去除效果最佳,浊度去除率达70.3%,上覆水溶解氧浓度明显提高,增加率为261.5%;(2)加石英砂悬浊液加速絮体沉淀,形成絮体之后加石英砂使水体浊度稳步下降,4 h之后,浊度去除率达74.9%,显著高于与絮凝剂一起加入的处理组(29.8%);(3)植物腐烂释放的含硫特征嗅味物质主要为硫化氢(H_2S)、甲硫醚和二甲基三硫醚.不同植物体腐烂释放的含硫挥发性有机物浓度差异显著,马来眼子菜释放的4种含硫有机物总和分别为莕菜和苦草释放的319.8%和252.2%;(4)CTS+PAC处理后苦草及马来眼子菜腐烂水体中挥发性有机硫化物浓度较对照组分别降低了18.6%和44.5%.PAC+PAM组合絮凝处理组对莕菜腐烂水体中H2S有较好的去除效果,去除率达到52.4%.CTS+PAC絮凝剂组合处理的H2S浓度均低于对照组,苦草、马来眼子菜和莕菜腐烂后黑臭水体中H2S浓度分别降低了27.4%、41.0%和28.6%.CTS+PAC组合对H2S和二甲基硫醚类物质等致臭物释放的抑制效果优于PAC+PAM组合絮凝处理. 相似文献
4.
浅水湖泊湖泛(黑水团)中的微生物生态学研究进展 总被引：5，自引：5，他引：0
"湖泛"是指湖泊水体中(包括沉积物)富含大量藻源性(或草源性)的生物质,在微生物的分解作用下,大量消耗氧气,出现厌氧分解,微生物在还原条件下,促进许多"黑臭"物质的形成,进而影响水质和湖泊生态系统结构与功能乃至造成环境灾难.与湖泛发生时的环境特征(如低溶解氧,低p H,高有机质,高总磷、总氮)相对应的是其简化的食物网结构和特殊的微生物类群.本文将主要针对湖泛中的微生物群落及其在物质循环中的作用展开综述.研究显示湖泛水体中主要微生物类群,如真菌、细菌厚壁菌门的梭菌以及产甲烷古菌等,在有机质的快速分解和厌氧矿化过程中发挥着重要作用;沉积物中主要的微生物功能群,如硫酸盐还原细菌、铁还原细菌、甲烷厌氧氧化菌和反硝化细菌等,是湖泛致黑物质形成的关键.缺氧及厌氧条件下碳、硫和铁等元素生物地球化学过程的相互关联以及多种微生物之间形成的互营共生可能是湖泛过程中功能微生物的重要特征.湖泛中微生物功能的进一步研究,亟需借鉴海洋低氧区及深海沉积物的经验,引用先进研究手段,提出可靠的生物地球化学证据.浅水湖泊湖泛(黑水团)中的微生物生态学探索将有助于从机理上揭示湖泛黑臭的成因. 相似文献
5.
于太湖草源性"湖泛"暴发期,采集柱状沉积物并应用peeper被动采样装置获得"湖泛"区原位沉积物间隙水.泥水样品分析表明:"湖泛"发生水域表层(0~7 cm)沉积物的含水率、孔隙度和有机质含量均明显高于对照区,其中有机质含量更是对照区样品的4倍左右,沉水植物残体促使表层沉积物物化性质改变的作用明显;"湖泛"发生水域表层沉积物间隙水中铵态氮(NH+4-N)、溶解性反应磷(SRP)及Fe2+含量远高于未发生区,植物残体降解对沉积物厌氧环境的营造显著.运用分子扩散模型对沉积物释放通量估算:"湖泛"发生区沉积物NH+4-N、SRP和Fe2+的释放速率分别是对照区的49.8、15.3和123.1倍.研究认为,草源性"湖泛"水体氮、磷等营养物含量升高的主要原因是沉积物的释放,而"湖泛"所营造的厌氧环境是氮、磷释放急剧增加的主要驱动因素. 相似文献
6.
太湖湖泛形成研究进展与展望 总被引：5，自引：4，他引：1
回顾近些年对太湖湖泛形成的研究进展,参考国外关于黑斑和缺氧现象的相关研究成果,重点从湖泛的感官特征与描述、缺氧与污染效应、湖泛形成的物质和气象条件,以及微生物和底泥作用等方面,进行了系统综述,总结出湖泛发生条件与生消过程.从基本属性方面,归纳出湖泛是指在适当的气象和地形等条件下,富营养湖泊局部水域因长时间聚积大量藻体或水草等生物质,在微生物和底泥参与下,形成边界可辨、散发恶臭的可移动黑色水团,并导致水质恶化和一些生物死亡的极端污染现象的定义.文章最后从湖泛研究的新技术、新手段,沉积物有效成分提供机制,湖泛发生的关键参数阈值确定,以及致黑致臭物稳定性机制等方面,对未来发展进行了展望. 相似文献
7.
"湖泛"是太湖水域近年来发生的重要环境灾害问题之一.根据2009年4-10月的太湖"湖泛"易发区巡测和跟踪监测资料,分析了2009年太湖水域"湖泛"发生情况.2009年太湖共发生11次小范围"湖泛",主要发生在太湖西岸、梅梁湾和贡湖湾局部水域.对比近年"湖泛"发生水域的水质指标,以及同期太湖蓝藻水华暴发、湖体水质及其变化情势,认为蓝藻水华强度、频次和面积与2007、2008年相比呈明显的下降趋势,从而可能降低了大面积"湖泛"暴发的机率;同时,2007年以来在太湖北部湖湾的生态清淤工程也降低了北部湖湾发生大面积"湖泛"的可能性.同期水质监测指标显示,2009年同期太湖水质综合评价为Ⅳ类、中富营养状态,而太湖湖西、竺山湖、梅梁湾水域仍为Ⅴ类或劣Ⅴ类,"湖泛"仍时有发生.蓝藻打捞、生态清淤、控源截污、"引江济太"调水是预防太湖"湖泛"的有效措施;同时,加强太湖"湖泛"巡查,建立太湖"湖泛"监测预警系统,及时发现太湖"湖泛",有序、妥善地处置黑臭水体,将对确保太湖饮用水水源地安全起到积极的作用. 相似文献
8.
湖泊水底Fe~(2+)和ΣS~(2-)浓度的快速增加是湖泛暴发最早发生于沉积物-水界面的主要前提,缺氧环境下水底扩散层附近Fe~(2+)和ΣS~(2-)的迁移是其在沉积物-水界面处稳定积累的重要原因.以蓝藻聚积水体沉积物-水界面为研究对象,应用湖泊过程模拟装置及间隙水被动采样等技术,重点研究了间隙水和底层上覆水中Fe~(2+)和ΣS~(2-)的垂向分布特征,并定量估算了二者的扩散通量及迁移方向.结果表明:湖泛样品水体沉积物-水界面处于典型的还原性环境,表层沉积物间隙水中Fe~(2+)和ΣS~(2-)浓度显著高于对照样品,二者在表层沉积物中积累趋势明显.湖泛水体沉积物-水界面处Fe~(2+)释放通量较高,表现出较强烈的自沉积物向上覆水方向的释放能力;而湖泛样品ΣS~(2-)在沉积物-水界面处释放通量为负,迁移方向为自上覆水向沉积物扩散.Fe~(2+)和ΣS~(2-)在湖泛水体沉积物-水界面处不同的迁移特征证明:缺氧/厌氧条件下,湖泊水体表层沉积物间隙水中高浓度Fe~(2+)向上覆水的扩散为湖泛致黑物质的形成提供了重要的物质基础;底层上覆水及界面水中SO~(2-)4在表层沉积物中被还原,为终端还原产物ΣS~(2-)为湖泛致黑物质的形成提供了另一重要物质来源. 相似文献
9.
2009—2017年太湖湖泛发生特征及其影响因素 总被引：3，自引：1，他引：2
湖泛是太湖蓝藻水华较为独特的灾害表征形式，也是危害湖泊生态服务功能的主要因素，认知其发生机制、演变特征对湖泊蓝藻水华灾害防控具有重要作用.本文基于2009-2017年江苏省水文部门逐年4-10月对太湖湖泛易发区现场巡查获得的湖泛发生状况数据，结合期间水质、入湖水量、营养盐负荷等环境条件变化监测，分析了太湖水域湖泛发生的时空变化特征，研究了湖泛发生前后的环境因子变化规律，探讨了湖泛强度年际波动成因.结果表明，2009-2017年太湖共发现面积超过0.01 km2的湖泛61起，年发生次数3~17次不等；湖泛发生位置主要集中在太湖湖西沿岸带，9年发生了32次，占总频次的一半以上；其次为梅梁湾；贡湖相对较少，而巡查的东部湖区未发现湖泛事件.通过对湖泛发生日与前10日的环境条件对比分析发现，湖泛发生前5天持续的高温、低压和低风速等气象条件有利于湖泛发生：气温连续高于25℃、气压低于101.0 kPa，有利于诱发湖泛；主导风向为东南风也有利于太湖西北部蓝藻水华严重区域的湖泛发生；大量蓝藻水华物质是湖泛发生的重要物质基础：湖泛发生前10日，湖体平均藻密度基本在1500万cells/L以上.湖泛发生强度还受前一年营养盐外源负荷的影响，湖泛发生频次较高的年份，前一年总磷和总氮营养盐入湖负荷也均处于较高水平.研究表明，尽管2007年无锡贡湖水厂发生饮用水危机以来太湖流域已经开展了大量的水环境治理工程，但是截至目前，太湖的湖泛发生风险仍处于较高水平，在营养盐还未控制到较低水平之前，太湖的湖泛巡查与防控仍是十分必要和艰巨的任务. 相似文献
10.
藻源性湖泛发生过程CDOM变化对水色的影响 总被引：1，自引：1，他引：0
利用Y-型沉积物再悬浮发生装置模拟湖泛发生过程,分析其中有色可溶性有机物(CDOM)的变化特征及其对水色的影响.结果表明,藻类死亡过程消耗大量的氧气,水中溶解氧在短时间内消失殆尽,形成厌氧环境;并同时分解产生大量CDOM,使得水中CDOM显著增多.前期阶段,CDOM浓度随时间一直升高,第6 d时CDOM浓度达到峰值,CDOM在443 nm处的吸收系数ag(443)为4.48 m-1.水体黑度值(Fe S浓度)呈先增大后减小的趋势,最大值0.35 mmol/L同样出现在第6 d,整个过程中,CDOM浓度和黑度值变化趋势一致,ag(443)与水体黑度呈显著正相关.利用Hydrolight和CIE颜色匹配函数模拟不同梯度的CDOM对水色的影响,发现随ag(443)增大,水体颜色也逐渐由绿色转为棕色,整体向长波方向移动,水色逐渐变暗.因此,可以认为CDOM浓度变化是引起湖泛水体发黑的重要原因之一,可作为定量监测湖泛强度的指示性参数. 相似文献
11.
《中国科学:地球科学(英文版)》2014,(9)
正SCIENCE CHINA Earth Sciences,an academic journal cosponsored by the Chinese Academy of Sciences and the National Natural Science Foundation of China,and published by Science China Press and Springer,is committed to publishing high-quality,original results in 相似文献
12.
《中国科学:地球科学(英文版)》2014,(12)
正SCIENCE CHINA Earth Sciences,an academic journal cosponsored by the Chinese Academy of Sciences and the National Natural Science Foundation of China,and published by Science China Press and Springer,is committed to publishing high-quality,original results in both basic and applied research. 相似文献
13.
In natural waters arsenic concentrations up to a few milligrams per litre were measured. The natural content of arsenic found in soils varies between 0.01 mg/kg and a few hundred milligrams per kilogram. Anthropogenic sources of arsenic in the environment are the smelting of ores, the burning of coal, and the use of arsenic compounds in many products and production processes in the past. A lot of arsenic compounds are toxic and cause acute and chronic poisoning. In aqueous environment the inorganic arsenic species arsenite (As(III)) and arsenate (As(V)) are the most abundant species. The mobility of these species is influenced by the pH value, the redox potential, and the presence of adsorbents such as oxides and hydroxides of Fe(III), Al(III), Mn(III/IV), humic substances, and clay minerals. 相似文献
14.
Due to deleterious effects on non-target organisms, the use of organotin compounds on boat hulls of small vessels (<25 m) has been widely prohibited. The International Maritime Organisation (IMO) resolved that the complete prohibition on organotin compounds acting as biocides in antifouling systems should commence in 2008. As a result of restrictions on the use of organotin based paints, other antifouling formulations containing organic biocides have been utilised. This survey was conducted to assess the contamination of replacement biocides in the marine environment following the ban of TBT-based paints. Surface sediments samples were collected in the major ports and marinas along the France Mediterranean coastline (Cote d’Azur) and analysed for organotin compounds, Irgarol 1051, Sea-nine 211TM, Chlorothalonil, Dichlofluanid and Folpet. Every port and marina exhibited high levels of organotin compounds, with concentrations in sediments ranging from 37 ng Sn g−1dry wt in Menton Garavan to over 4000 ng Sn g−1dry wt close to the ship chandler within the port of Villefranche-sur-Mer. TBT degradation indexes suggested that fresh inputs are still made. Among the other antifoulants monitored, only Irgarol 1051 exhibited measurable concentrations in almost every port, with concentrations ranging from 40 ng g−1dry wt (Cannes) to almost 700 ng g−1dry wt (Villefranche-sur-Mer, ship chandler). 相似文献
15.
Ian R. Falconer 《洁净——土壤、空气、水》2005,33(1):64-71
Microcystins are cyclic heptapeptide toxins produced by a range of cyanobacterial genera. These cyanobacteria occur naturally in drinking water reservoirs subject to eutrophication, and in rivers and natural lakes. Because of the diversity of organisms, the toxins occur, from oligo‐mesotrophic lakes in North Temperate latitudes, to hypertrophic tropical ponds. The toxins are responsible for numerous cases of injury and death of domestic animals, and human poisoning from drinking water. The initial poisoning includes hepatic cell death. This leads to secondary effects from liver deficiency, including jaundice and photosensitisation. The toxic effects are largely due to inhibition of phosphatase enzymes, acting to regulate protein phosphorylation. The consequences include structural damage, apoptosis and, at lower concentrations, cell cycle effects and tumour promotion. As there is no clear evidence for direct carcinogenesis by microcystins, they are classed as non‐carcinogenic toxins in drinking water. Guideline Values for safe drinking water are derived from data for subchronic rodent toxicity, using the No Observed Adverse Effect Level (the highest dose giving no toxicity). To this dose are applied uncertainty factors, to calculate a Tolerable Daily Intake. On the basis of a standard bodyweight and water consumption the Guideline Value is determined for drinking water. For microcystin‐LR the WHO have set a provisional Guideline Value of 1 μg/L for drinking water. 相似文献
16.
The geomagnetic field and secular variation exhibit asymmetrical spatial features which are possibly originating from an heterogeneous thermal control of the Earth's lower mantle on the core. The identification of this control in magnetic data is subject to several difficulties, some of which can be alleviated by the use of core surface flow models. Using numerical dynamos driven by heterogeneous boundary heat flux, we confirm that within the parameter space accessible to simulations, time average surface flows obey a simple thermal wind equilibrium between the Coriolis and buoyancy forces, the Lorentz, inertial and viscous forces playing only a secondary role, even for Elsasser numbers significantly larger than 1. Furthermore, we average the models over the duration of three vortex turnovers, and correlate them with a longer time average which fully reveals the signature of boundary heterogeneity. This allows us to quantify the possibility of observing mantle control in core surface flows averaged over a short time period. A scaling analysis is performed in order to apply the results to the Earth's core. We find that three vortex turnovers could represent between 100 and 360 years of Earth time, and that the heat flux heterogeneity at the core-mantle boundary could be large enough to yield an observable signature of thermal mantle control in a time average core surface flow within reach of the available geomagnetic data. 相似文献
17.
Richard McCreary John McGaughey Yves Potvin Dave Ecobichon Marty Hudyma Harald Kanduth Alain Coulombe 《Pure and Applied Geophysics》1992,139(3-4):349-373
Located in northern Québec, the Lac Shortt Mine was a small gold mine consisting of a thin subvertical orebody which was mined in three main phases. High stress and rockbursting conditions were experienced when ore was extracted in the upper zone between the surface and a depth of 500 metres during the first two phases of mining. Severe rockbursts were experienced in late 1989 near the shaft and in the footwall development following a deepening of the mine shaft to a depth of 830 m and partial development of footwall drift access for the third phase of mining (the mining of the lower zone starting at a depth of 830 m moving upward toward a depth of 500 m). A 16-channel Electrolab MP250 microseismic system, with a Queen's University Full-Waveform piggy-back system, was installed underground at the site due to these problems.It was expected that the thinning sill would be subjected to an ever-increasing load as the thickness of the 500 m sill pillar decreased in the face of the mining excavation from below. A monitoring program consisting of the microseismic monitoring system, a range of conventional geomechanics monitoring tools as well as the undertaking of periodic seismic tomography surveys to assess the ongoing state of stress and rock mass condition within the sill was therefore warranted.The anomalously high-magnitude stress field and the brittle rockmass created a situation in which rockmass failure was common and violent. In the creation and thinning of the sill pillar, the location of banded microseismic activity was crucial in tracing rockmass failure and the associated ground control problems. Reliable source-location determination enabled the identification of areas of stress increase. The movement of the rockmass failure front could be followed, and was responsible for stope dilution, footwall and orebody development deterioration, and caving.Source-mechanism analyses gave accurate double-couple solutions for approximately forty percent of these events having at least ten recognizable polarities. Results suggested movement along vertical north-south striking or vertical east-west striking features. Underground observation of damaged access points showed that vertical north-south striking joints were experiencing failure.The microseismic activity, which was consistently concentrated close to the southwest and northeast corners of current production stopes, could be explained by a stress field oriented obliquely to the strike of the orebody, as measured prior to shrinkage of the sill pillar byin situ stress measurements and observed borehole overbreaks. The orientations of theP andT axes for the microseismic activity further confirmed that the stress field oriented obliquely to strike.While an increase in compressional-wave velocity of 2.3 percent, corresponding to a measured stress increase of approximately 10 MPa could be measured by repeated tomographic surveys, it was relatively small and only a factor of two or so above the velocity measured uncertainty. The relative insensitivity of thein situ rock mass modulus to the applied stress is believed to be largely due to the rockmass discontinuities being relatively closed prior to stress increase, as substantiated by the small deformations seen by the extensometer and borehole camera. This situation existed because of the very high pre-mining stress level.The experimental demonstration that the rock could not absorb substantially increased load through the mechanism of discontinuity closure or tightening (which would be reflected in the modulus) may be evidence in itself of potentially burst-prone ground, such as encountered at Lac Shortt. 相似文献
18.
19.
The inability to detect the presence of viable Helicobacter pylori bacteria in environmental waters has hindered the public health community in assessing the role water may play in the transmission of this pathogen. This work describes a cultural enrichment method coupled with an H. pylori‐specific PCR to identify these bacteria in water. While far from perfected at the present time, this represents an exciting new approach to studying the significance of water as a transmission mechanism for H. pylori. Evidence is presented that indicates culturable H. pylori bacteria were found using this enrichment/PCR method in a local groundwater source. 相似文献
20.
Response spectrum predictions for potential near-field and far-field earthquakes affecting Hong Kong: rock sites 总被引：1，自引：0，他引：1
N. T. K. Lam A. M. Chandler J. L. Wilson G. L. Hutchinson 《Soil Dynamics and Earthquake Engineering》2002,22(1)
To realistically assess the seismic risk relating to built infrastructures in Hong Kong and in the neighbouring coastal cities of southern Guangdong province, it is necessary to predict ground shaking induced by different earthquake scenarios with good accuracy. A companion paper has described the modelling of the spatial and temporal distribution of the diffused seismic activities in the region, based on the newly-developed ‘Expanding Circular Disc’ (ECD) method. Representative Magnitude–Distance (M–R) combinations for both near-field and far-field earthquakes (in relation to Hong Kong) have been derived using the ECD method. The present paper describes the modelling of the response spectrum on rock sites associated with the predicted M–R combinations, using the Component Attenuation Model (CAM) that was also developed recently by the authors, based on stochastic simulations of the seismological model. The significant effects of soil resonance on the response spectrum are described in a separate publication.The accuracy of CAM in modelling ground motion properties on rock sites has been tested here by comparisons with (i) strong motions recorded in Taiwan and South China from the 1999 ‘Chi-Chi’ earthquake in Taiwan (M=7.6), (ii) motions recorded in South China from another earthquake occurring in the southern Taiwan Strait in the same year (M=5.1), and (iii) historical seismic intensity data obtained within South China. The overall capability of CAM in modelling both near-field and far-field attenuation has been shown to be unmatched by existing empirical models. Results of the comparison studies confirm the accuracy of CAM, particularly within an epicentral distance of 300–400 km.This study shows that the developed serviceability response spectra (i.e. at short return periods) are controlled mainly by the earthquake recurrence behaviour of major distant seismic sources. In contrast, the ultimate response spectra (i.e. at long return periods) relate to events with magnitudes close to the maximum credible earthquake (MCE) limit, the effect of which may also be represented by the Characteristic Response Spectrum (CRS). Both types of earthquake scenario can be significantly affected by the regional crustal properties. The proposed response spectrum envelopes have been compared with previously developed recommendations, and a critical review has been conducted. The intrinsic advantages of the ECD–CAM modelling approach have been highlighted, emphasising its directness and transparency when compared with the more complex process required to implement traditional Probabilistic Seismic Hazard Assessment (PSHA). 相似文献