共查询到20条相似文献，搜索用时 31 毫秒
1.
Tarek H. Abdoun Da Ha Michael J. O’Rourke Michael D. Symans Thomas D. O’Rourke Michael C. Palmer Harry E. Stewart 《Soil Dynamics and Earthquake Engineering》2009
Seismic ground faulting is a severe hazard for continuous buried pipelines. Over the years, researchers have attempted to understand pipe behavior, most frequently via numerical modeling and simulation. However, there has been little, if any, physical modeling and tests to verify the numerical modeling approaches and assumptions. This paper presents results of five pairs of centrifuge tests designed to investigate the influence of various factors on the behavior of buried high-density polyethylene (HDPE) pipelines subjected to strike-slip faulting. Parameters considered are the soil moisture content, fault offset rate, relative burial depth (H/D), and pipe diameter. The centrifuge test results show that pipe behavior, specifically pipe strain, is nominally not affected by the soil moisture content and fault offset rate when the pipe is subjected to strike-slip faulting. On the other hand, the burial depth ratio (H/D) and pipe diameter influence peak pipe strain, and in some cases, the ground soil failure pattern. 相似文献
2.
Determination of the role of entrapped air in water flow in a closed soil pipe using a laboratory experiment 
下载免费PDF全文
下载免费PDF全文 Soil pipes, continuous macropores parallel to the soil surface, are an important factor in hillslope hydrological processes. However, the water flow dynamics in soil pipes, especially closed soil pipes, are not well understood. In this study, the water and air dynamics within closed soil pipes have been investigated in a bench‐scale laboratory experiment by using a soil box with an artificial acrylic soil pipe. In order to grasp the state of water and air within the soil pipe, we directly measured the existing soil pipe flow and air pressure in the soil pipe. The laboratory experiment showed that air in the soil pipe had an important role in the water flow in the closed soil pipe. When air entrapment occurred in the soil pipe before the soil matrix around the soil pipe was saturated with water, water intrusion in the soil pipe was prevented by air entrapped in the pipe, which inhibited the soil pipe flow. This air entrapment in the soil pipe was controlled by the soil water and air flow. Moreover, after the soil pipe flow started, the soil pipe was not filled completely with water even when the soil pipe was completely submerged under the groundwater table. The entrapped air in the soil pipe prevented further water intrusion in the soil pipe. 相似文献
3.
The evaluation of the wave-induced pore pressure around a buried pipeline is particularly important for pipeline engineers involved in the design of offshore pipelines. Most previous investigations of the wave-induced dynamic response around an offshore pipeline have limited to two-dimensional cases. In this paper, a three-dimensional model including buried pipeline is established, based on the existing DYNE3WAC models. Based on the proposed numerical model and poro-elastic soil material assumption, the effects of wave and soil characteristics, such as wave period, water depth, shear modulus and permeability, and configuration of pipelines, such as pipeline radius and pipeline buried depth, on the wave-induced excess pore pressure will be examined. Numerical results indicated that the normalized excess pore pressures versus z/h near the pipeline increase as the obliquity angle, wave period and water depth increase, and they decrease as the burial depth and radius of pipeline increase above the pipeline. Soil permeability has obvious influence on the wave-induced normalized excess pore pressure, and different soil material will result in distinct computation results. 相似文献
4.
This paper describes a laboratory model test carried out on high-density polyethylene (HDPE), small diameter pipes buried in trenches, which subjected to repeated loadings to simulate the vehicle loads. Deformation of the pipe was recorded at eight points on the circumference of the tested pipes to measure the radial deformations and detect cross-sectional pipe profiles. Also settlement of the soil surface during the test up to 1000 cycles of loadings was recorded, until its value become stable or the excessive settlement was happened. The parameters varied in the testing program include height of buried depth, relative density of the sand and intensity of stress on the soil surface. The influence of various repeated loads (with magnitude of 250, 400 and 550 kPa) at relative densities of 42%, 57% and 72% in different embedded depth of 1.5–3 times of pipe diameter were investigated. Based on the results, in medium and dense sand relative density, the pipe embedded in depth of 3.0D and 2.0D, respectively, mostly remained undamaged (the maximum value of VDS is less than 5%) and increased the safety of buried pipes under different magnitude of repeated loads. The records of the pipe deformation and settlement of the soil surface due to the repeated loads have been compared in different conditions. These values increase rapidly during the initial loading cycles by a rate decreasing significantly as the number of cycles increase. The influence of the first cycle was also found to be one of the main behavioral characteristics of buried pipes under repeated loads. The ratio of deformation of pipe at first cycle to last cycle changes from 0.60 to 0.85 in different of tests. Finally for the obtained results, a non-linear power model has been developed to estimate the vertical diametral strain of buried pipe and settlement of the soil surface based on the model test data. It should be noted that only one type of pipe and one type of sand are used in laboratory tests. 相似文献
5.
Extinction depth and evapotranspiration from ground water under selected land covers 总被引：7，自引：0，他引：7
In many landscapes, vegetation extracts water from both the unsaturated and the saturated zones. The partitioning of evapotranspiration (ET) into vadose zone evapotranspiration and ground water evapotranspiration (GWET) is complex because it depends on land cover and subsurface characteristics. Traditionally, the GWET fraction is assumed to decay with increasing depth to the water table (DTWT), attaining a value of 0 at what is termed the extinction depth. A simple assumption of linear decay with depth is often used but has never been rigorously examined using unsaturated-saturated flow simulations. Furthermore, it is not well understood how to relate extinction depths to characteristics of land cover and soil texture. In this work, variable saturation flow theory is used to simulate GWET for three land covers and a range of soil properties under drying soil conditions. For a water table within half a meter of the land surface, nearly all ET is extracted from ground water due to the close hydraulic connection between the unsaturated and the saturated zones. For deep-rooted vegetation, the decoupling of ground water and vadose zone was found to begin at water table depths between 30 and 100 cm, depending on the soil texture. The decline of ET with DTWT is better simulated by an exponential decay function than the commonly used linear decay. A comparison with field data is consistent with the findings of this study. Tables are provided to vary the extinction depth for heterogeneous landscapes with different vegetation cover and soil properties. 相似文献
6.
沉陷区域埋地管线数值模拟分析 总被引：4，自引：0，他引：4
场地的不均匀沉陷是导致埋地管线破坏的重要原因之一。本文考虑了材料非线性、几何非线性以及管土接触非线性,将管线计算分析模型模拟为四节点薄壳单元结构,周围填覆土体采用八节点六面体单元划分。管土相互作用模拟为三维刚性与柔性的面面接触单元结构,并采用线性位移加载来模拟土体的沉陷作用,对三维薄壳有限元模型进行数值计算分析。通过比较不同参数,如沉陷长度、沉陷深度、埋深、管径、径厚比、土特性等对管线的反应影响,得出管线在沉陷情况下的应力和应变的关系,通过算例分析,说明了该方法能更好地模拟管线的破坏过程,该方法将为沉陷区域埋地管线数值模拟提供理论分析依据。 相似文献
7.
地震作用下土体发生液化之后,由于超静孔隙水压力的产生和土体抗剪强度的降低,管道易发生上浮破坏。为研究管道上浮动力反应的影响因素,基于OpenSees有限元软件,通过目标反应谱和谱匹配等方法选取地震波,考虑不同管土特性和地震动特性,对地震作用下管道上浮动力反应进行了二维数值模拟。结果表明:土体相对密度、管径和管道埋深对管道上浮反应的影响较大,分别给出了土体相对密度、管径、管道埋深对管道上浮位移的影响规律及对应拟合公式;长持时地震动作用下,超静孔隙水压力消散较慢,管道上浮位移可达短持时地震动作用下管道上浮位移的2倍左右;近断层脉冲地震动作用下,管道上浮破坏和横向破坏两种破坏模式同时存在,且由于速度脉冲效应,管道横向破坏风险大于上浮破坏风险。 相似文献
8.
由于管道与土体的刚度相差较大,在振动荷载下,两者的运动不能相互协调,致使在研究管道破坏方面,管土之间的变形传递是一个极其重要的研究方向。目前学者对弯管的管土变形传递研究做得较少。本文通过弯管与土体的缩尺振动台试验及三维有限元模型,得出了地震作用下埋地弯管的变形传递系数的拟合公式。然后将试验结果与拟合公式的计算结果和有限元的模拟结果进行对比,证实了拟合公式的合理性,并分析了管道弯头处变形传递系数的变化规律,包括对不同管径、埋深、壁厚、土性和弯头角度的分析,证实了这些因素对管土之间的变形传递影响都很大,说明弯头处变形传递系数拟合公式对管道的抗震具有重大意义。 相似文献
9.
利用ANSYS有限元分析软件,建立了由场地土液化引起的地下管道上浮反应的分析模型。用土弹簧模型模拟地下管道的受力特点,考虑了管土之间相互作用的非线性特征,通过算例分析了管道在发生上浮反应时的应力应变曲线,探讨了液化区埋地管道在发生上浮位移时的受力特征,得出了一些有意义的结果。主要有:管线的应力应变以轴向为主,并且管顶和管底的受力最大,管侧相对于管顶和管底轴向应力应变很小可以忽略;最大应变位于液化区和非液化区交界处;管线中点处等效应力达到极值等等。 相似文献
10.
Seismic ground faulting is the greatest hazard for continuous buried pipelines.Over the years,researchers have attempted to understand pipeline behavior mostly via numerical modeling such as the finite element method.The lack of well-documented field case histories of pipeline failure from seismic ground faulting and the cost and complicated facilities needed for full-scale experimental simulation mean that a centrifuge-based method to determine the behavior of pipelines subjected to faulting is best to verify numerical approaches.This paper presents results from three centrifuge tests designed to investigate continuous buried steel pipeline behavior subjected to normal faulting.The experimental setup and procedure are described and the recorded axial and bending strains induced in a pipeline are presented and compared to those obtained via analytical methods.The influence of factors such as faulting offset,burial depth and pipe diameter on the axial and bending strains of pipes and on ground soil failure and pipeline deformation patterns are also investigated.Finally,the tensile rupture of a pipeline due to normal faulting is investigated. 相似文献
11.
Miad Saberi Farhad Behnamfar Mahmood Vafaeian 《Bulletin of Earthquake Engineering》2013,11(5):1373-1402
A buried pipe extends over long distances and passes through soils with different properties. In the event of an earthquake, the same pipe experiences a variable ground motion along its length. At bends, geometrically a more complicated problem exists where seismic waves propagating in a certain direction affect pipe before and after bend differently. Studying these different effects is the subject of this paper. Two variants for modeling of pipe, a beam model and a beam-shell hybrid model are examined. The surrounding soil is modeled with the conventional springs in both models. A suitable boundary condition is introduced at the ends of the system to simulate the far field. Effects of angle of incidence in the horizontal and vertical planes, angle of pipe bend, soil type, diameter to thickness ratio, and burial depth ratio on pipe strains at bend are examined thoroughly. It is concluded that extensional strains are highest at bends and these strains increase with the angle of incidence with the vertical axis. The pipe strains attain their peaks when pipe bend is around $135^{\circ }$ and exceed the elastic limit in certain cases especially in stiffer soils, but remain below the rupture limit. Then equations for predicting the seismic response of the buried pipe at bend are developed using the analytical data calculated above and regression analysis. It is shown that these semi-analytical equations predict the response with very good accuracy saving much time and effort. 相似文献
12.
The successful operation of buried infrastructure within urban environments is fundamental to the conservation of modern living standards. In this paper a novel multi-sensor image fusion framework has been proposed and investigated using dynamic Bayesian network for automatic detection of buried underworld infrastructure. Experimental multi-sensors images were acquired for a known buried plastic water pipe using Vibro-acoustic sensor based location methods and Ground Penetrating Radar imaging system. Computationally intelligent conventional image processing techniques were used to process three types of sensory images. Independently extracted depth and location information from different images regarding the target pipe were fused together using dynamic Bayesian network to predict the maximum probable location and depth of the pipe. The outcome from this study was very encouraging as it was able to detect the target pipe with high accuracy compared with the currently existing pipe survey map. The approach was also applied successfully to produce a best probable 3D buried asset map. 相似文献
13.
Flow through a saturated idealized hillslope with a single soil pipe was simulated using a finite difference solution to the equation for three-dimensional Darcian flow in saturated heterogeneous media. The proportions of hillslope discharge originating from flow through the soil matrix and from flow through a soil pipe were determined, considering such factors as the radius, depth and length of the pipe, pipe spacing, and the length and slope of the hillslope. Results demonstrate that soil pipes can contribute a significant amount, and in many instances, the majority of total subsurface stormflow. 相似文献
14.
To estimate the demand of structures, investigating the correlation between engineering demand parameters and intensity measures (IMs) is of prime importance in performance-based earthquake engineering. In the present paper, the efficiency and sufficiency of some IMs for evaluating the seismic response of buried steel pipelines are investigated. Six buried pipe models with different diameter to thickness and burial depth to diameter ratios, and different soil properties are subjected to an ensemble of 30 far-field earthquake ground motion records. The records are scaled to several intensity levels and a number of incremental dynamic analyses are performed. The approach used in the analyses is finite element modeling. Pipes are modeled using shell elements while equivalent springs and dashpots are used for modeling the soil. Several ground motion intensity measures are used to investigate their efficiency and sufficiency in assessing the seismic demand and capacity of the buried steel pipelines in terms of engineering demand parameter measured by the peak axial compressive strain at the critical section of the pipe. Using the regression analysis, efficient and sufficient IMs are proposed for two groups of buried pipelines separately. The first one is a group of pipes buried in soils with low stiffness and the second one is those buried in soils with higher stiffness. It is concluded that for the first group of pipes, \(\sqrt {{\text{VSI}}[\upomega_{1} ({\text{PGD}} + {\text{RMS}}_{\text{d}} )]}\) followed by root mean square of displacement (RMSd) are the optimal IMs based on both efficiency and sufficiency; and for the second group, the only optimal IM is PGD2/RMSd. 相似文献
15.
Headcut formation and migration was sometimes mistaken as the result of overland flow, without realizing that the headcut was formed and being influenced by flow through soil pipes into the headcut. To determine the effects of the soil pipe and flow through a soil pipe on headcut migration in loessic soils, laboratory experiments were conducted under free drainage conditions and conditions of a perched water table. Soil beds with a 3-cm deep initial headcut were formed in a flume with a 1.5-cm diameter soil pipe 15 cm below the bed surface. Overland flow and flow into the soil pipe was applied at a constant rate of 68 and 1 l min−1 at the upper end of the flume. The headcut migration rate and sediment concentrations in both surface (channel) and subsurface (soil pipe) flows were measured with time. The typical response was the formation of a headcut that extended in depth until an equilibrium scour hole was established, at which time the headcut migrated upslope. Pipeflow caused erosion inside the soil pipe at the same time that runoff was causing a scour hole to deepen and migrate. When the headcut extended to the depth of the soil pipe, surface runoff entering the scour hole interacted with flow from the soil pipe also entering the scour hole. This interaction dramatically altered the headcut processes and greatly accelerated the headcut migration rates and sediment concentrations. Conditions in which a perched water table provided seepage into the soil pipe, in addition to pipeflow, increased the sediment concentration by 42% and the headcut migration rate by 47% compared with pipeflow under free drainage conditions. The time that overland flow converged with subsurface flow was advanced under seepage conditions by 2.3 and 5.0 min compared with free drainage conditions. This study confirmed that pipeflow dramatically accelerates headcut migration, especially under conditions of shallow perched water tables, and highlights the importance of understanding these processes in headcut migration processes. © 2020 John Wiley & Sons, Ltd. 相似文献
16.
场地土液化引起的地下管道上浮反应研究 总被引：7，自引：3，他引：4
本文利用虚功原理,建立了场地土液化引起的地下管道的上浮反应分析模型,用弹性地基梁来模拟地下管道,并考虑了土的非线性约束作用、管道的初始变形、液化区长度、管道的初始轴力等的影响。采用非线性增量有限元法,对场地土液化引起的地下管道的上浮反应进行了研究,给出了部分计算结果。 相似文献
17.
花管土钉已被广泛应用于基坑工程中,但其抗拔承载机理尚不明确。根据花管土钉的支护原理,分析其三种破坏形式,提出花管土钉的四个受力阶段;基于库仑土压力理论,将滑动土体上方看作均布荷载,推导出花管土钉极限抗拔承载力的计算公式;结合兰州某基坑实例,将《建筑基坑支护技术规程》中的花管土钉极限抗拔承载力计算方法与本文计算方法进行拉拔试验,并对结果进行对比分析。研究表明：花管土钉的破坏模式主要为花管杆体被拉断、出浆锚固体被剪断及出浆锚固体前端土体变形过大;花管土钉的四个受力阶段包括静止阶段、塑性区产生阶段、塑性区扩张阶段和破坏阶段;在花管土钉极限抗拔承载力的组成中,出浆锚固体提供的抗拔力所占比重随花管埋深的增大而显著增大,是花管土钉极限抗拔承载力的重要组成部分。 相似文献
18.
19.
玻璃钢夹砂管在土木水利工程领域得到了愈来愈广泛的应用,但现有的埋地管道地震响应分析模型大多不考虑管-土动力相互作用,且多针对均质材料管道,无法应用于具有明显层状复合材料结构特征的玻璃钢夹砂管。基于玻璃钢夹砂管的层状复合材料结构特征,建立了完整的埋地玻璃钢夹砂管地震响应分析模型,在数值分析模型中,考虑了管-土间复杂的动力相互作用,以及地震散射波从有限域向无限域的传播。算例分析表明,所建立的埋地玻璃钢夹砂管地震响应分析模型可合理地分析埋地玻璃钢夹砂管在地震荷载作用下的动力响应。 相似文献
20.
Soil pipes (continuous macropores expanding laterally in the soil subsurface) are a key factor controlling hillslope water cycles and sediment transport. Soil pipes usually enhance slope stability under rainfall events through their high water drainage ability, and pipe clogging by sediments is regarded as a risk for slope failure. In this study, we conducted a bench-scale pipe clogging experiment to clarify the effect of air mobility in soil pipes on water flow and water pressure build-up in the slope at the clogged point. Before pipe clogging, the soil pipe drained rainwater effectively and lowered the groundwater table. After the pipe clogging event, the mobility of air in the soil pipe before the clogging determined the water flow in the slope. When the air in the soil pipe connected to the atmosphere and moved freely, the water level in the soil pipe increased at the pipe clogging, and water pressure build-up was limited near the pipe outlet. On the other hand, when air in the soil pipe was entrapped by the clogging, water pressure suddenly increased, and the groundwater table of the whole slope rose correspondingly. This study clearly demonstrated the importance of pipe morphology with respect to air connectivity between the pipe and atmosphere to elucidate the water flow and slope stability during the pipe clogging event. © 2019 John Wiley & Sons, Ltd. 相似文献