共查询到20条相似文献，搜索用时 46 毫秒
1.
By using a thermally stratified wind tunnel, we have successfullysimulated stably stratified boundary layers (SBL), in which the meantemperature increases upward almost linearly. We have investigated the flow structure and the effects of near-linearstable stratification on the transfer of momentum and heat. Thevertical profiles of turbulence quantities exhibit different behaviour in two distinct stability regimes of the SBLflows with weak and strong stability. For weak stability cases, theturbulent transfer of momentum and heat is basically similar to that for neutral turbulent boundary layers, although it is weakenedwith increasing stability. For strong stability cases, on the other hand,the time-mean transfer is almost zero over the whole boundary-layer depth.However, the instantaneous turbulent transfer frequently occurs in bothgradient and counter-gradient directions in the lower part of the boundary layer. This is due to the Kelvin–Helmholtz (K–H) shear instability and therolling up and breaking of K–H waves. Moreover, the internal gravity wavesare observed in the middle and upper parts of all stable boundary layers. 相似文献
2.
Turbulence structure in stably stratified boundary layers isexperimentally investigated by using a thermally stratified wind tunnel. Astably stratified flow is created by heating the wind tunnel airflow to atemperature of about 50 °C and by cooling the test-section floor to asurface temperature of about 3 °C. In order to study the effect ofbuoyancy on turbulent boundary layers for a wide range of stability, thevelocity and temperature fluctuations are measured simultaneously at adownwind position of 23.5 m from the tunnel entrance, where the boundarylayer is fully developed. The Reynolds number, Re, ranges from 3.14× 104 to 1.27 × 105, and the bulk Richardson number, Ri,ranges from 0 to 1.33. Stable stratification rapidly suppresses thefluctuations of streamwise velocity and temperature as well as the verticalvelocity fluctuation. Momentum and heat fluxes are also significantlydecreased with increasing stability and become nearly zero in the lowest partof the boundary layer with strong stability. The vertical profiles ofturbulence quantities exhibit different behaviour in three distinct stabilityregimes, the neutral flows, the stratified flows with weak stability(Ri = 0.12, 0.20) and those with strong stability (Ri= 0.39,0.47, 1.33). Of these, the two regimes of stratified flows clearly showdifferent vertical profiles of the local gradient Richardson number Ri,separated by the critical Richardson number Ri cr of about 0.25. Moreover,turbulence quantities in stable conditions are well correlated with Ri. 相似文献
3.
The atmospheric stable boundary layer (SBL) with a low-level jet is simulated experimentally using a thermally stratified
wind tunnel. The turbulence structure and flow characteristics are investigated by simultaneous measurements of velocity and
temperature fluctuations and by flow visualization. Attention is focused on the effect of strong wind shear due to a low-level
jet on stratified boundary layers with strong stability. Occasional bursting of turbulence in the lower portion of the boundary
layer can be found in the SBL with strong stability. This bursting originates aloft away from the surface and transports fluid
with relatively low velocity and temperature upward and fluid with relatively high velocity and temperature downward. Furthermore,
the relationship between the occurrence of turbulence bursting and the local gradient Richardson number (Ri) is investigated.
The Ri becomes larger than the critical Ri, Ricr = 0.25, in quiescent periods. On the other hand, the Ri number becomes smaller than Ricr during bursting events. 相似文献
4.
Artificial neural network (ANN) modeling has been performed to predict turbulent boundary layer characteristics for rough terrain based on experimental tests conducted in a boundary-layer wind tunnel to simulate atmospheric boundary layer using passive roughness devices such as spires, barriers, roughness elements on the floor, and slots in the extended test section. Different configurations of passive devices assisted to simulate urban terrains. A part of the wind tunnel test results are used as training sets for the ANN, and the other part of the test results are used to compare the prediction results of the ANN. Two ANN models have been developed in this study. The first one has been used to predict mean velocity, turbulence intensity, and model length scale factor. Results show that ANN is an efficient, accurate, and robust modeling procedure to predict turbulent characteristics of wind. In particular, it was found that the ANN-predicted wind mean velocities are within 4.7%, turbulence intensities are within 6.2%, and model length scale factors are within 3.8% of the actual measured values. In addition, another ANN model has been developed to predict instantaneous velocities that enables calculating the power spectral density of longitudinal velocity fluctuations. Results show that the predicted power spectra are in a good agreement with the power spectra obtained from measured instantaneous velocities. 相似文献
5.
Andrey A. Grachev P. Ola G. Persson Edgar L. Andreas Peter S. Guest 《Boundary-Layer Meteorology》2005,116(2):201-235
Turbulent and mean meteorological data collected at five levels on a 20-m tower over the Arctic pack ice during the Surface
Heat Budget of the Arctic Ocean experiment (SHEBA) are analyzed to examine different regimes of the stable boundary layer
(SBL). Eleven months of measurements during SHEBA cover a wide range of stability conditions, from the weakly unstable regime
to very stable stratification. Scaling arguments and our analysis show that the SBL can be classified into four major regimes:
(i) surface-layer scaling regime (weakly stable case), (ii) transition regime, (iii) turbulent Ekman layer, and (iv) intermittently
turbulent Ekman layer (supercritical stable regime). These four regimes may be considered as the basic states of the traditional
SBL. Sometimes these regimes, especially the last two, can be markedly perturbed by gravity waves, detached elevated turbulence
(‘upside down SBL’), and inertial oscillations. Traditional Monin–Obukhov similarity theory works well in the weakly stable
regime. In the transition regime, Businger–Dyer formulations work if scaling variables are re-defined in terms of local fluxes,
although stability function estimates expressed in these terms include more scatter compared to the surface-layer scaling.
As stability increases, the near-surface turbulence is affected by the turning effects of the Coriolis force (the turbulent
Ekman layer). In this regime, the surface layer, where the turbulence is continuous, may be very shallow (< 5 m). Turbulent
transfer near the critical Richardson number is characterized by small but still significant heat flux and negligible stress.
The supercritical stable regime, where the Richardson number exceeds a critical value, is associated with collapsed turbulence
and the strong influence of the earth’s rotation even near the surface. In the limit of very strong stability, the stress
is no longer a primary scaling parameter. 相似文献
6.
Eeva Mäkiranta Timo Vihma Anna Sjöblom Esa-Matti Tastula 《Boundary-Layer Meteorology》2011,140(1):105-123
Sonic anemometer and profile mast measurements made in Wahlenbergfjorden, Svalbard Arctic archipelago, in May 2006 and April
2007 were employed to study the atmospheric boundary layer over sea-ice. The turbulent surface fluxes of momentum and sensible
heat were calculated using eddy correlation and gradient methods. The results showed that the literature-based universal functions
underestimated turbulent mixing in strongly stable conditions. The validity of the Monin-Obukhov similarity theory was questionable
for cross-fjord flow directions and in the presence of mesoscale variability or topographic effects. The aerodynamic roughness
length showed a dependence on the wind direction. The mean roughness length for along-fjord wind directions was (2.4 ± 2.6)
× 10−4 m, whereas that for cross-fjord directions was (5.4 ± 2.8) × 10−3 m. The thermal stratification and turbulent fluxes were affected by the synoptic situation with large differences between
the 2 years. Channelling effects and drainage flows occurred especially during a weak large-scale flow. The study periods
were simulated applying the Weather Research and Forecasting (WRF) model with 1-km horizontal resolution in the finest domain.
The results for the 2-m air temperature and friction velocity were good, but the model failed to reproduce the spatial variability
in wind direction between measurement sites 3 km apart. The model suggested that wind shear above the stable boundary layer
provided a non-local source for the turbulence observed. 相似文献
7.
8.
Stratified Atmospheric Boundary Layers 总被引：32，自引：24，他引：8
L. Mahrt 《Boundary-Layer Meteorology》1999,90(3):375-396
Various features of different stability regimes of the stable boundary layer are discussed. Traditional layering is examined in terms of the roughness sublayer, surface layer, local similarity, z-less stratification and the region near the boundary-layer top. In the very stable case, the strongest turbulence may be detached from the surface and generated by shear associated with a low level jet, gravity waves or meandering motions. In this case, similarity theory and the traditional concept of a boundary-layer break down. The elevated turbulence may intermittently recouple to the surface. Inability to adequately measure turbulent fluxes in very stable conditions limits our knowledge of this regime. 相似文献
9.
The Coupling State of an Idealized Stable Boundary Layer 总被引：1，自引：1，他引：0
Otávio C. Acevedo Felipe D. Costa Gervásio A. Degrazia 《Boundary-Layer Meteorology》2012,145(1):211-228
The coupling state between the surface and the top of the stable boundary layer (SBL) is investigated using four different schemes to represent the turbulent exchange. An idealized SBL is assumed, with fixed wind speed and temperature at its top. At the surface, two cases are considered, first a constant temperature, 20 K lower than the SBL top, and later a constant 2 K h−1 cooling rate is assumed for 10 h after a neutral initial condition. The idealized conditions have been chosen to isolate the influence of the turbulence formulations on the coupling state, and the intense stratification has the purpose of enhancing such a response. The formulations compared are those that solve a prognostic equation for turbulent kinetic energy (TKE) and those that directly prescribe turbulence intensity as a function of atmospheric stability. Two TKE formulations are considered, with and without a dependence of the exchange coefficients on stability, while short and long tail stability functions (SFs) are also compared. In each case, the dependence on the wind speed at the SBL top is considered and it is shown that, for all formulations, the SBL experiences a transition from a decoupled state to a coupled state at an intermediate value of mechanical forcing. The vertical profiles of potential temperature, wind speed and turbulence intensity are shown as a function of the wind speed at the SBL top, both for the decoupled and coupled states. The formulation influence on the coupling state is analyzed and it is concluded that, in general, the simple TKE formulation has a better response, although it also tends to overestimate turbulent mixing. The consequences are discussed. 相似文献
10.
The experiment IGLOS (Investigation of the Greenland Boundary Layer Over Summit) was conducted in June and July 2002 in the central plateau of the Greenland inland ice. The German research aircraft Polar2, equipped with the turbulence measurement system Meteopod, was used to investigate turbulence and radiation flux profiles near research station “Summit Camp”. Aircraft measurements are combined with measurements of radiation fluxes and turbulent quantities made from a 50 m tower at Summit Camp operated by Eidgenössische Technische Hochschule (ETH) Zürich. During all six flight missions, well-developed stable boundary layers were found. Even in high-wind conditions, the surface inversion thickness did not exceed roughly 100 m. The turbulent height of the stable boundary layer (SBL) was found to be much smaller than the surface inversion thickness. Above the surface layer, significant turbulent fluxes occurred only intermittently in intervals on the order of a few kilometres. Turbulent event fraction in the upper SBL shows the same dependence on gradient Richardson number as reported for near-surface measurements. Clear-air longwave radiation divergence was always found to contribute significantly to the SBL heat budget. In low-wind cases, radiative cooling even turned out to be dominant. 相似文献
11.
The convective boundary layer (CBL) with a wide range of stability is simulated experimentally using a thermally stratified wind tunnel, and numerically by direct numerical simulation (DNS). The turbulence structures and flow characteristics of various CBL flows, capped by a strong temperature inversion and affected by surface shear, are investigated. The various vertical profiles of turbulence statistics similar to those from the observed CBL in the field are successfully simulated in both the wind-tunnel experiment and in DNS. The comparison of the wind-tunnel data and DNS results with those of atmospheric observations and water-tank studies shows the crucial dependence of the turbulence statistics in the upper part of the layer on the strength of the inversion layer, as well as the modification of the CBL turbulence regime by the surface shear. 相似文献
12.
Günther Heinemann 《Boundary-Layer Meteorology》2002,103(1):49-81
Turbulence structures in the katabatic flow in the stable boundary layer (SBL) over the ice sheet are studied for two case studies with high wind speeds during the aircraft-based experiment KABEG (Katabatic wind and boundary layer front experiment around Greenland) in the area of southern Greenland. The aircraft data allow the direct determination of turbulence structures in the katabatic flow. For the first time, this allows the study of the turbulence structure in the katabatic wind system over the whole boundary layer and over a horizontal scale of 80 km.The katabatic flow is associated with a low-level jet (LLJ), with maximum wind speeds up to 25 m s-1. Turbulent kinetic energy (TKE) and the magnitude of the turbulent fluxes show a strong decrease below the LLJ. Sensible heat fluxes at the lowest level have values down to -25 W m-2. Latent heat fluxes are small in general, but evaporation values of up to +13 W m-2 are also measured. Turbulence spectra show a well-defined inertial subrange and a clear spectral gap around 250-m wavelength. While turbulence intensity decreases monotonously with height above the LLJ for the upper part of the slope, high spectral intensities are also present at upper levels close to the ice edge. Normalized fluxes and variances generally follow power-law profiles in the SBL.Terms of the TKE budget are computed from the aircraft data. The TKE destruction by the negative buoyancy is found to be very small, and the dissipation rate exceeds the dynamical production. 相似文献
13.
In this study the role of atmospheric boundary layer schemes in climate models is investigated. Including a boundary layer scheme in an Earth system model of intermediate complexity (EMIC) produces only minor differences in the estimated global distribution of sensible and latent heat fluxes over land (upto about 15% of the net radiation at the surface). However, neglecting of boundary layer processes, such as the development of a well-mixed layer over land or the impact of stability on the exchange coefficient in the surface layer, leads to erroneous surface temperatures, especially in convective conditions with low wind speeds. As these conditions occur frequently, introducing a boundary layer scheme in an EMIC gives reductions in June-July-August averaged surface temperature of 1–2 °C in wet areas, to 5–7 °C in desert areas. Even a relatively simple boundary layer scheme provides reasonable estimates of the surface fluxes and surface temperatures. Detailed schemes that solve explicitly the turbulent fluxes within the boundary layer are only required when vertical profiles of potential temperature are needed. 相似文献
14.
Experiments on integral length scale control in atmospheric boundary layer wind tunnel 总被引：2，自引：1，他引：1
Accurate predictions of turbulent characteristics in the atmospheric boundary layer (ABL) depends on understanding the effects of surface roughness on the spatial distribution of velocity, turbulence intensity, and turbulence length scales. Simulation of the ABL characteristics have been performed in a short test section length wind tunnel to determine the appropriate length scale factor for modeling, which ensures correct aeroelastic behavior of structural models for non-aerodynamic applications. The ABL characteristics have been simulated by using various configurations of passive devices such as vortex generators, air barriers, and slot in the test section floor which was extended into the contraction cone. Mean velocity and velocity fluctuations have been measured using a hot-wire anemometry system. Mean velocity, turbulence intensity, turbulence scale, and power spectral density of velocity fluctuations have been obtained from the experiments for various configuration of the passive devices. It is shown that the integral length scale factor can be controlled using various combinations of the passive devices. 相似文献
15.
S.D. Wright 《Boundary-Layer Meteorology》1998,89(2):175-195
The adaptation of the atmospheric boundary layer to a change in the underlying surface roughness is an interesting problem and hence much research, theoretical, experimental, and numerical, has been undertaken. Within the atmospheric boundary layer an accurate numerical model for the turbulent properties of the atmospheric boundary layer needs to be implemented if physically realistic results are to be obtained. Here, the adaptation of the atmospheric boundary layer to a change in surface roughness is investigated using a first-order turbulence closure model, a one-and-a-half-order turbulence closure model and a second-order turbulence closure model. Perturbations to the geostrophic wind and the pressure gradients are included and it is shown that the second-order turbulence closure model, namely the standard k - model, is inferior to a lower-order closure model if a modification to limit the turbulent eddy size within the atmospheric boundary layer is not included within the model. 相似文献
16.
17.
A generalized form of a recently developed minimum dissipation model for subfilter turbulent fluxes is proposed and implemented in the simulation of thermally stratified atmospheric boundary-layer flows. Compared with the original model, the generalized model includes the contribution of buoyant forces, in addition to shear, to the production or suppression of turbulence, with a number of desirable practical and theoretical properties. Specifically, the model has a low computational complexity, appropriately switches off in laminar and transitional flows, does not require any ad hoc shear and stability corrections, and is consistent with theoretical subfilter turbulent fluxes. The simulation results show remarkable agreement with well-established empirical correlations, theoretical predictions, and field observations in the atmosphere. In addition, the results show very little sensitivity to the grid resolution, demonstrating the robustness of the model in the simulation of the atmospheric boundary layer, even with relatively coarse resolutions. 相似文献
18.
Albert F. Kurbatskiy Lyudmila I. Kurbatskaya 《Meteorology and Atmospheric Physics》2009,104(1-2):63-81
A modified three-parameter model of turbulence for a thermally stratified atmospheric boundary layer (ABL) is presented. The model is based on tensor-invariant parameterizations for the pressure–strain and pressure–temperature correlations that are more complete than the parameterizations used in the Mellor–Yamada model of level 3.0. The turbulent momentum and heat fluxes are calculated with explicit algebraic models obtained with the aid of symbol algebra from the transport equations for momentum and heat fluxes in the approximation of weakly equilibrium turbulence. The turbulent transport of heat and momentum fluxes is assumed to be negligibly small in this approximation. The three-parameter $E - \varepsilon - {\left\langle {\theta ^{2} } \right\rangle }$ model of thermally stratified turbulence is employed to obtain closed-form algebraic expressions for the fluxes. A computational test of a 24-h ABL evolution is implemented for an idealized two-dimensional region. Comparison of the computed results with the available observational data and other numerical models shows that the proposed model is able to reproduce both the most important structural features of the turbulence in an urban canopy layer near the urbanized ABL surface and the effect of urban roughness on a global structure of the fields of wind and temperature over a city. The results of the computational test for the new model indicate that the motion of air in the urban canopy layer is strongly influenced by mechanical factors (buildings) and thermal stratification. 相似文献
19.
The impact of sea waves on sensible heat and momentum fluxes is described. The approach is based on the conservation of heat and momentum in the marine atmospheric surface layer. The experimental fact that the drag coefficient above the sea increases considerably with increasing wind speed, while the exchange coefficient for sensible heat (Stanton number) remains virtually independent of wind speed, is explained by a different balance of the turbulent and the wave-induced parts in the total fluxes of momentum and sensible heat.Organised motions induced by waves support the wave-induced stress which dominates the surface momentum flux. These organised motions do not contribute to the vertical flux of heat. The heat flux above waves is determined, in part, by the influence of waves upon the turbulence diffusivity.The turbulence diffusivity is altered by waves in an indirect way. The wave-induced stress dominates the surface flux and decays rapidly with height. Therefore the turbulent stress above waves is no longer constant with height. That changes the balance of the turbulent kinetic energy and of the dissipation rate and, hence the diffusivity.The dependence of the exchange coefficient for heat on wind speed is usually parameterized in terms of a constant Stanton number. However, an increase of the exchange coefficient with wind speed is not ruled out by field measurements and could be parametrized in terms of a constant temperature roughness length. Because of the large scatter, field data do not allow us to establish the actual dependence. The exchange coefficient for sensible heat, calculated from the model, is virtually independent of wind speed in the range of 3–10 ms-1. For wind speeds above 10 ms-1 an increase of 10% is obtained, which is smaller than that following from the constant roughness length parameterization.The investigation was in part supported by the Netherlands Geosciences Foundation (GOA) with financial aid from the Netherlands Organization for Scientific Research (NWO). 相似文献
20.
本文采用二阶闭合的湍流边界层模式,进行一系列数值试验以模拟边界层中连续线源的扩散状况。试验表明:无论在稳定的或不稳定的边界层中,高源的扩散能力都低于低源;在稳定层中,粗糙地表上的大气扩散能力高于光滑表面;在相同风速和地表净辐射情况下,粗糙表面上的大气扩散能力反而低于光滑表面;对流边界层中存在反梯度输送,因而K理论的应用受到限制。试验还表明,修正的Kazanski-Monin参数可能比Monin-Obukhov长度更能反映大气的扩散能力。 相似文献