共查询到19条相似文献，搜索用时 158 毫秒
1.
针对现阶段深水软黏土地基防波堤建设的设计理论和稳定性分析方法尚不成熟,结合实际工程,采用三维弹塑性有限元数值分析方法,研究在水平或竖直单一方向荷载以及复合加载条件下软黏土地基上沉箱防波堤的失稳模式,提出破坏包络线的稳定性判别方法。在波浪水平荷载作用下,深水软基上沉箱防波堤发生倾覆失稳破坏,失稳转动点为沉箱底面以下中轴线偏右的某点,不同于规范中规定的岩石或砂质地基沉箱倾覆转动点为其后踵点;在重力等竖向荷载作用下,沉箱的失稳模式为结构整体下陷,抛石基床及地基形成连贯的塑性区域,呈现较明显地冲剪破坏形式;在水平、竖向复合荷载作用下,软基上沉箱防波堤的破坏包络线由结构倾覆破坏线和地基承载力破坏线组成,包络线将荷载组合区分成稳定区、仅发生水平承载力不足倾覆破坏区、仅发生地基竖向承载力不足破坏区、同时发生水平承载力和地基竖向承载力不足破坏区4个区域。研究成果为深水软基沉箱防波堤建设提供参考和借鉴。 相似文献
2.
复合加载下桶形基础循环承载性能数值分析 总被引：1，自引：0，他引：1
作为一种新型基础形式,吸力式桶形基础除了承受海洋平台结构及自身重量等竖向荷载的长期作用之外,往往还遭受波浪等所产生的水平荷载及其力矩等其它荷载分量的瞬时或循环作用。对复合加载模式下软土地基中桶形基础及其结构的循环承载性能尚缺乏合理的分析与计算方法。应用Andersen等对重力式平台基础及地基所建议的分析方法,基于软黏土的循环强度概念,在大型通用有限元分析软件ABAQUS平台上,通过二次开发,将软土的循环强度与Mises屈服准则结合,针对吸力式桶形基础,基于拟静力分析建立了复合加载模式下循环承载性能的计算模型,并与复合加载作用下极限承载性能进行了对比。由此表明,与极限承载力相比,桶形基础的循环承载力显著降低。 相似文献
3.
4.
复合加载模式作用下地基承载性能数值分析 总被引：11，自引：3，他引：11
确定竖向荷载(V)、水平荷载(H)和力矩(M)共同作用下建筑物地基的破坏模式及在荷载空间(H,V,M)中的破坏包络面是地基设计中的关键问题。为提高Swipe试验方法计算精度,提出了改进方案,进而利用有限元方法分析了复合加载模式作用下均质粘性土地基上条形基础的破坏包络面。计算表明,基于改进Swipe试验方法的数值模拟结果明显好于常规Swipe试验方法。针对海洋工程中实际复合加载模式的特点,探讨了竖向荷载分量V对地基破坏模式和H-M荷载平面上的破坏包络线的影响,结果表明竖向荷载分量显著地改变了地基的破坏模式及包络线的形状。 相似文献
5.
港口、海洋工程结构物基础一般处于复合加载状态,其极限承载力通常采用近来引入的极限荷载图进行评价.对位于地基表面的重力式海洋基础,需要考虑基础与地基间的接触特性对极限承载力的影响.以大型通用有限元软件ABAQUS为计算平台,建立了复合加载模式的地基极限承载力数值分析方法;针对饱和黏土地基上的表面基础,利用在ABAQUS平台上开发的接触计算模块,模拟基础与地基间竖向可分离、切向完全粘结的接触作用;进而基于建立的分析方法,进行系统的有限元计算,分析地基的破坏模式随荷载条件的变化,给出地基的极限荷载包络图,并与经典承载力计算公式结果进行对比.研究结果表明,经典承载力计算公式低估了三维荷载条件下的地基极限承载力,有限元计算模型及数值分析方法,可以较好地分析研究地基的失稳机理及承载力特性,并可考虑基础与地基不同的接触条件对破坏模式及组合极限承载力的影响. 相似文献
6.
在一个大型土池中进行了软土中组合四桶基础在竖向静荷载与水平循环荷载共同作用下的承载力模型试验,研究了竖向静荷载与水平循环荷载对组合桶形基础破坏形式与承载力的影响。试验结果表明,组合四桶基础的变形主要包括水平循环变形与竖向循环累积沉降。基础的破坏形式取决于水平循环荷载与竖向静荷载。若竖向静荷载较小,过大的水平循环位移将导致基础破坏;随竖向静荷载增加,竖向循环累积沉降将变为导致基础破坏的主要原因。试验结果还表明,在不同竖向静荷载与水平循环荷载共同作用下,基础的水平循环承载力大约为水平静承载力的70%左右。 相似文献
7.
平台在海上受风、浪、流、冰等水平载荷作用产生倾斜 ,而土壤粘接力、摩擦力和土抗力是平台的抗拔和抗倾力 ,桶基平台应满足抗拔、抗倾稳定的要求 ,以保证平台的整体稳定性。讨论了桶基平台受水平力作用时 ,桶形基础的破坏模式及其计算方法 ,阐述了抗倾稳定计算方法 相似文献
8.
平台在海上受风、浪、流、冰等水平载荷作用产生倾斜，而土壤粘接力、摩擦力和土抗力是平台的抗拔和抗倾力，桶基平台应满足抗拔、抗倾稳定的要求，以保证平台的整体稳定性。讨论了桶基平台受水平力作用时，桶形基础的破坏模式及其计算方法，阐述了抗倾稳定计算方法。 相似文献
9.
针对用于海上风力发电机的伞式吸力锚基础(USAF)实际条件下的受力特点,采用数值模拟方法,基于大型通用有限元软件ABAQUS构建数值计算模型,对伞式吸力锚基础在H-V、H-T、V-T荷载平面内以及H-V-T非共面复合加载模式下的承载特性进行分析,进而推导其破坏包络面数学表达式。分析中采用固定位移比加载法进行复合加载,并将桶顶位移作为失效破坏标准。结果表明：(1)拟定的应力归一化复合加载破坏包络面椭圆曲线方程可以较好地模拟不同主筒长径比USAF在不同荷载空间内的破坏包络面形式;(2)H-T空间内USAF复合承载性能随主筒长径比(L/D)的增大而提高,而H-V、V-T空间内变化不明显;(3)绘制了H-V-T空间内USAF三维破坏包络面,可根据实际受荷状态与包络面之间的相对位置关系,评价实际工况下伞式吸力锚基础的稳定性。 相似文献
10.
循环荷载下饱和粉土地基单桩水平承载特性试验研究 总被引：3，自引：0，他引：3
在饱和粉土地基中进行了单桩水平静力和循环加载室内模型试验,实测得到静载和循环荷载下桩身弯矩与深度的关系、桩身最大弯矩与循环次数之间的关系等,推导出静载和循环荷载下粉土的p-y曲线,并结合API规范给出了针对粉土地基的相关参数。单桩循环加载试验结果表明,在一定深度内随着循环次数增大,粉土极限抗力显著减小,文中给出了不同循环次数和深度下粉土地基极限抗力的折减系数建议值。 相似文献
11.
The bearing behavior of suction caissons supporting offshore wind turbines under two-way cyclic lateral loading and dead load in clay was investigated with consideration of soil strength degradation and adhesive interface friction between caisson walls and heterogeneous clay using the finite-element package ABAQUS.An ABAQUS built-in user subroutine was programmed to calculate the adhesive interface friction between clay and caisson walls.The results of parametric studies showed that the degradation of bearing capacity could be aggravated by the decrease of the aspect ratio.The offset between the rotation point of the soil inside the caisson and the central axis of the caisson increased with the increasing vertical load and number of cycles.The linearly increasing strength profile and adhesive interface led to the formation of an inverted spoon failure zone inside the caisson.The settlement-rotation curves in each cycle moved downwards with increasing number of cycles due to the soil strength degradation. 相似文献
12.
Coastal protection is proposed to be made out of a contiguous caisson type of wall. These caissons can be designed to resist both lateral static and cyclic loading. With adequate depth of embedment, the walls can be designed to offer significant lateral passive resistance to counteract the lateral static and cyclic loading arising out of wave action. This article describes a set of laboratory tests on model caissons embedded into soft marine clay with different embedment depths. Specially designed earth pressure cells are embedded into the caisson at different depths. A pneumatic system was used to apply lateral static and cyclic loading. Test beds were prepared conforming to soft clay conditions in a test tank of appropriate size. The test results reveal that with this type of arrangement the variation in earth pressure with depth can be conveniently established. The earth pressure developed is related to the lateral load applied. The depth at which the maximum earth pressure occurs is same for both static and cyclic loading. Further, under cyclic loading there is no failure encountered even under cyclic loading level corresponding to 0.9 times the ultimate static lateral capacity. 相似文献
13.
Hiroyoshi Hirai 《Marine Georesources & Geotechnology》2018,36(7):805-817
An investigation was made to present analytical solutions of cyclic response to suction caisson subjected to inclined cyclic loadings in clay using a three-dimensional displacement approach. A model representing the relationship between vertical load and vertical displacement and that between lateral load and lateral displacement along the skirt of suction caisson subjected to cyclic loadings is proposed for overconsolidated clay. For the effect of vertical load on cyclic load capacity of suction caisson, using the Mindlin solution in the case of a vertical point load, the vertical stress of soil under the base of suction caisson is presented. For the stress state of soil beneath the base of suction caisson subjected to cyclic loading, the Mohr–Coulomb failure line and critical state line are presented and the relationship between total stress, effective mean principal stress, stress difference, and pore-pressure is elucidated. The comparison of results predicted by the present method for a suction caisson subjected to cyclic loadings in clay has shown good agreement with those obtained from field tests. Cyclic behavior of clay up to failure is made clear from the relationship between cyclic tensile load, vertical and lateral displacements, and rotation and that between depth, vertical, and lateral pressures. 相似文献
14.
Huayang Lei Jingjin Liu Min Liu Zhipeng Zhang Mingjing Jiang 《Marine Georesources & Geotechnology》2017,35(2):281-291
The mechanical behavior of clay subjected to cyclic loading is important to consider in the design of the foundations of many types of structures that must resist cyclic loading, such as subgrades and offshore foundations, because clay undergoes greater settlement under cyclic loading than under static loading. The difference in settlement between these two loading patterns due to creep behavior is affected by the cyclic frequency and the cyclic stress ratio. This study investigated the effects of the frequency and cyclic stress ratio of cyclic loading on the creep behavior of a natural clay in China using stress-controlled triaxial tests. The assessed the following parameters: three frequencies, four cyclic stress ratios, and six vertical stresses. The test results indicate that the soft clay displays accelerated creep behavior under dynamic loads. A specific “limit frequency” (in this case, 0.2 Hz) and a “safe load” at which the strain of the soft clay increases very slowly were observed. The effect of the effective axial stress on the creep behavior increases with the increase in the cyclic stress ratio. Based on the tests, the critical cyclic stress ratio is 0.267 at a certain effective axial stress and frequency. 相似文献
15.
1 .IntroductionIt has beenrealizedthat constructing gravitystructures onsoft soil foundations is a difficult task,especiallyinthe marine area where boththe geological and environmental conditions are severe .Thisisnot only because the bearing capacity of the soft foundation is relatively low, but also because thestrength of the soft soil will befurther weakened bythe waveloading (Andersenet al .,1988 ;Ander-sen and Lauritzsen,1988 ; Yasuhara ,1988) .The strength weakening may cause serious d… 相似文献
16.
Suction caisson foundations are often subjected to vertical uplift loads, but there are still no wide and spread engineering specifications on design and calculation method for uplift bearing capacity of suction caisson foundation.So it is important to establish an uplift failure criterion. In order to study the uplift bearing mechanism and failure mode of suction caisson foundation, a series of model tests were carried out considering the effects of aspect ratio,soil permeability and loading mode. Test results indicate that the residual negative pressure at the top of caisson is beneficial to enhance uplift bearing capacity. The smaller the permeability coefficient is, the higher the residual negative pressure will be. And the residual negative pressure is approximately equal to the water head that causes seepage in the caisson. When the load reaches the ultimate bearing capacity, both the top and bottom negative pressures are smaller than Su and both the top and bottom reverse bearing capacity factors are smaller than 1.0 in soft clay. Combined the uplift bearing characteristics of caisson in sandy soil and soft clay, the bearing capacity composition and the calculation method are proposed. It can provide a reference for the engineering design of suction caisson foundation under vertical load. 相似文献
17.
Foundations of offshore structures are designed to withstand a combination of static and cyclic loads due to ocean waves. Wave action on offshore structures can cause a significant amount of cyclic horizontal and vertical forces to be transmitted to the soil through the foundation. In all these cases, these cyclic loads are considered to be superimposed over the initial sustained static stress due to the self-weight of structures. This study considers various factors that influence the development of deformation and pore water pressure in a typical cemented marine clay. These results show that the sustained static shear stress significantly influences the strength and deformation behavior of marine clay under cyclic loading. Up to a certain range of sustained static stress, there is an improvement in strength during cyclic loading and the cyclic strains are greatly reduced. 相似文献
18.
Foundations of offshore structures are designed to withstand a combination of static and cyclic loads due to ocean waves. Wave action on offshore structures can cause a significant amount of cyclic horizontal and vertical forces to be transmitted to the soil through the foundation. In all these cases, these cyclic loads are considered to be superimposed over the initial sustained static stress due to the self-weight of structures. This study considers various factors that influence the development of deformation and pore water pressure in a typical cemented marine clay. These results show that the sustained static shear stress significantly influences the strength and deformation behavior of marine clay under cyclic loading. Up to a certain range of sustained static stress, there is an improvement in strength during cyclic loading and the cyclic strains are greatly reduced. 相似文献
19.
Response of skirted suction caissons to monotonic lateral loading in saturated medium sand 总被引：2，自引：1，他引：1
Monotonic lateral load model tests were carried out on steel skirted suction caissons embedded in the saturated medium sand to study the bearing capacity. A three-dimensional continuum finite element model was developed with Z_SOIL software. The numerical model was calibrated against experimental results. Soil deformation and earth pressures on skirted caissons were investigated by using the finite element model to extend the model tests. It shows that the ＂skirted＂ structure can significantly increase the lateral capacity and limit the deflection, especially suitable for offshore wind turbines, compared with regular suction caissons without the ＂skirted＂ at the same load level. In addition, appropriate determination of rotation centers plays a crucial role in calculating the lateral capacity by using the analytical method. It was also found that the rotation center is related to dimensions of skirted suction caissons and loading process, i.e. the rotation center moves upwards with the increase of the ＂skirted＂ width and length; moreover, the rotation center moves downwards with the increase of loading and keeps constant when all the sand along the caisson＇s wall yields. It is so complex that we cannot simply determine its position like the regular suction caisson commonly with a specified position to the length ratio of the caisson. 相似文献