共查询到17条相似文献，搜索用时 109 毫秒
1.
为了研究桩长对海底防沉板—桩复合基础在水平、弯矩和扭转荷载作用下承载特性的影响,以我国南海水深200 m的某工程实例为研究对象,利用Flac3D有限差分仿真软件建立了计算模型。研究了桩长为4 m、6 m和8 m的防沉板—桩复合基础在水平、弯矩和扭转荷载作用下的极限承载力和荷载传递机理。结果表明,桩长超过6 m时复合基础的水平承载力显著增长,在水平加载过程中,防沉板总是先达到极限状态而破坏,桩基础的贡献在加载后期体现,且桩长为4 m、8 m时,桩基础与防沉板的连接处弯矩最大;随着桩长的增加,复合基础的抗弯承载力大幅提高,桩基础对复合基础的抗弯承载力贡献增大,当桩长超过8 m,桩长的增加对提高复合基础的抗弯承载力意义不大;在弯矩加载过程中,桩长对于防沉板、桩基础的荷载分配有显著影响,桩长为4 m时,外荷载主要由防沉板承担,当桩长超过4 m时,外荷载主要由桩基础承担;当扭转荷载不超过2 100 k N·m时,防沉板承担主要荷载,直至防沉板达到极限状态而发生旋转,随后桩基础的承载力逐渐发挥;对于桩长为6 m、8 m的复合基础,其极限状态根据防沉板适用性准则确定。 相似文献
2.
水下生产系统防沉板结构形式改进研究 总被引：1，自引：0，他引：1
防沉板是水下生产系统的重要基础形式,在海洋工程开发中有着广泛应用。基础承载能力不仅决定防沉板的适用范围,还关乎水下生产系统的稳定性与安全性。运用有限元软件ABAQUS,建立防沉板与土体的相互作用模型,通过平衡初始地应力,设置主从接触,施加重力荷载与位移约束,用Swipe法对不同结构形式防沉板进行数值模拟。比较分析多种防沉板在复合加载模式下的极限复合承载能力差异,讨论了单轴竖向承载力、V-H、H-M荷载空间破坏包络线。计算结果显示,防沉板是否有底部结构、底部结构的形式、布置以及深度对荷载位移曲线以及破坏包络线有着显著的影响。提出了通过改进防沉板结构形式以克服承载力不足的问题的建议,为拓宽防沉板的运用领域提供了参考。 相似文献
3.
为了研究海底防沉板—桩复合基础在地震荷载作用下的动力反应特性,以我国南海深水工程实例为研究对象,利用Flac3D有限差分仿真软件建立了计算模型,土体采用Mohr-Coulomb本构模型,模型底部输入EL Centro地震波,对不同桩长的复合基础进行分析计算.在该特定工程背景下,研究结果表明:随着桩长的增加,防沉板顶部加速度放大系数呈减小趋势;地震荷载下,复合基础发生震陷,沉降量在地震波加速度峰值过后趋于稳定;当桩长为6m时,复合基础的水平振动程度和震陷量最小;由于桩基础把震动能量传输到深部土层中,复合基础周围土体的加速度响应值小于远场土体.在动力时域内,防沉板与桩连接处弯矩最大,需要在此处增设加固装置. 相似文献
4.
砂土中带裙板防沉板基础竖向承载力的上限解 总被引：1，自引：1，他引：0
防沉板是深海油气工程中水下生产系统的重要基础形式,因其埋深浅、水下施工方便等特点而具有广阔的应用前景。为了满足基础抗滑移的要求,可在防沉板底部设置裙板,裙板的存在增加了防沉板竖向承载力计算的难度。将防沉板基础简化为带裙板条形基础,考虑了内部土体与基础的相互作用,建立了竖向承载模式,即Terzaghi模式;运用极限分析法推导了该承载模式的上限解,引入了一个能够反映裙板与基础内部土体共同作用的经验参数—土体破坏率(η),其大小决定了地基中土体滑动面的范围;通过分析确定了在二维简化条件下带裙板防沉板基础的土体破坏率与基础高宽比的关系;并研究了土体破坏率不同时,地基承载力系数Nq和Nγ与土体内摩擦角之间的关系。 相似文献
5.
6.
自升式钻井平台插桩是地基土在桩靴荷载作用下发生连续的塑性破坏的动态过程,当地基极限承载力等于桩靴荷载时插桩完成。经典土力学极限承载力理论对土体潜在滑动面做了假设,无法有效分析土体内部的破坏过程。本研究应用有限元法（FEM ）对插桩过程进行了模拟,得到地基土的破坏机制以及中间荷载下土体的应力、应变情况,通过和各理论公式计算的极限承载力进行对比分析,分析影响地基极限承载力的因素。研究表明,基础宽度与硬土层厚度的比值 B/H越大,下卧软土层越容易发生塑性破坏,极限承载力明显下降,当B/H＜0．286时,可以忽略下卧软土层对地基承载力的影响。 相似文献
7.
防沉板基础裙板入泥阻力计算和长度设计是海洋工程水下生产系统基础设计的关键,基于南海番禺和荔湾地区水下防沉板基础裙板贯入模拟试验,验证了Lunne和Eide等建立的裙板入泥阻力经验计算方法对南海水下生产系统防沉板裙板设计的可靠性,确定了南海地区裙板入泥的端部阻力系数(0.320～0.360)和侧摩阻力系数(0.008～0.014 5),为南海水下生产系统防沉板基础裙板入泥阻力计算和裙板长度设计提供了依据,确保了南海地区水下生产系统的顺利安装。在工程地质调查时,既可以进行土壤钻孔取样并与已开展裙板贯入模拟试验的番禺和荔湾地区土壤组成和粒度对比,也可开展静力触探试验或裙板贯入模拟试验,得到裙板入泥的端部阻力系数和侧摩阻力系数。 相似文献
8.
近海海床表层多为软黏土或淤泥质土,为探究海床表层软土对海上风电宽浅式筒型基础承载特性的影响,以中国广东某海域风电场为背景,通过有限元分析的方法,研究竖向、水平、弯矩荷载作用下软土层厚度和土体强度对基础极限承载力、破坏模式以及筒基土压力分布的影响。研究结果表明:当软土层厚度小于H/2(H为筒裙高度)时,单向荷载作用下宽浅式筒型基础极限承载力随软土层厚度的增加呈线性减小的趋势;当软土层厚度大于H/2后,承载力降低速率逐渐增大。表层软土的存在,使得塑性区范围缩小,软土层内土体塑性破坏更加明显。竖向荷载作用下,随软土层厚度的增大,筒顶承载先减小后增大,筒内侧摩阻力先增大后减小;水平荷载和弯矩作用下,筒侧被动土压力的降低是引起软土覆盖地基中基础承载能力降低的主要因素。 相似文献
9.
复合加载模式作用下地基承载性能数值分析 总被引：11，自引：3，他引：11
确定竖向荷载(V)、水平荷载(H)和力矩(M)共同作用下建筑物地基的破坏模式及在荷载空间(H,V,M)中的破坏包络面是地基设计中的关键问题。为提高Swipe试验方法计算精度,提出了改进方案,进而利用有限元方法分析了复合加载模式作用下均质粘性土地基上条形基础的破坏包络面。计算表明,基于改进Swipe试验方法的数值模拟结果明显好于常规Swipe试验方法。针对海洋工程中实际复合加载模式的特点,探讨了竖向荷载分量V对地基破坏模式和H-M荷载平面上的破坏包络线的影响,结果表明竖向荷载分量显著地改变了地基的破坏模式及包络线的形状。 相似文献
10.
吸力基础具有施工速度快、安装过程中受海况天气影响小且易于回收重复利用等优点,被广泛应用于海洋工程。当吸力基础作为海上风电塔架的基础时,常常承受较大的水平荷载,因此其水平承载力是设计的主控因素。介绍了海上风机基础的设计要求,分析了影响基础水平承载性状的因素,总结了吸力基础受水平单调荷载、水平循环荷载和不同荷载组合三个方面的研究现状。讨论了水平荷载的大小、水平加载的高度(偏心率)、循环荷载的频率、循环荷载的次数、循环荷载的幅值、循环荷载的方向性、竖向荷载对吸力基础水平承载性状的影响,考虑了水平荷载的非共线性,指出了目前研究的不足,明确了吸力基础水平承载性状进一步研究的方向,提出了供工程实践参考的建议。 相似文献
11.
ABSTRACTBucket foundations have been widely used for a variety of offshore applications. The effects of skirt length on ultimate bearing capacity of bucket foundation have been studied and reported in published scientific papers. However, few studies have addressed the behavior of bucket foundations in loose saturated sand. In this paper, a series of experimental investigations were performed to determine the bearing capacity of bucket foundation under uniaxial loading. The experiments were conducted on small-scale foundations under vertical loading in loose saturated sand. It was found that increasing the skirt length would enhance the bearing capacity of bucket foundation. As reflected in the present study, bearing strength might be enhanced more than 5 times in loose saturated sand in comparison to surface footing with equivalent diameter. Based on the experimental investigation, a depth factor was proposed to approximate bearing capacity of bucket foundations in terms of those for surface footing and embedment ratio. Moreover, the corresponding settlement of foundation at the failure load was found to increase with skirt length. 相似文献
12.
复合加载下桶形基础循环承载性能数值分析 总被引：1，自引：0，他引：1
作为一种新型基础形式,吸力式桶形基础除了承受海洋平台结构及自身重量等竖向荷载的长期作用之外,往往还遭受波浪等所产生的水平荷载及其力矩等其它荷载分量的瞬时或循环作用。对复合加载模式下软土地基中桶形基础及其结构的循环承载性能尚缺乏合理的分析与计算方法。应用Andersen等对重力式平台基础及地基所建议的分析方法,基于软黏土的循环强度概念,在大型通用有限元分析软件ABAQUS平台上,通过二次开发,将软土的循环强度与Mises屈服准则结合,针对吸力式桶形基础,基于拟静力分析建立了复合加载模式下循环承载性能的计算模型,并与复合加载作用下极限承载性能进行了对比。由此表明,与极限承载力相比,桶形基础的循环承载力显著降低。 相似文献
13.
In this paper, results of a three-dimensional finite element study addressing the effect of embedment ratio (L/D) of caisson foundations on the undrained bearing capacity under uniaxial and combined loadings are discussed. The undrained response of caisson foundations under uniaxial vertical (V), horizontal (H) and moment (M) loading are investigated. A series of equations are proposed to predict the ultimate vertical, moment and maximum horizontal bearing capacity factors. The undrained response of caisson foundations under combined V-H and V-M load space is studied and presented using failure envelopes generated with side-swipe method. The kinematic mechanism accompanying failure under uniaxial loading is addressed and presented for different embedment ratios. Predictions of the uniaxial bearing capacities are compared with other models and it is confirmed that the proposed equations appropriately describe the capacity of caisson foundations under uniaxial vertical, horizontal and moment loading in homogenous undrained soils. The results of this paper can be used as a basis for standard design codes of off-shore skirted shallow foundations which will be the first of its kind. 相似文献
14.
Study on Failure Mechanism and Bearing Capacity of Three-Dimensional Rectangular Footing Subjected to Combined Loading 总被引：2，自引：0，他引：2
This paper presents two kinematic failure mechanisms of threc-dimensional rectangular footing resting on homogeneous undrained clay foundation under uniaxial vertical loading and uniaxial moment loading. The failure mechanism under vertical loading comprises a plane strain Prandti-type mechanism over the central part of the longer side, and the size of the mechanism gradually reduces at the ends of the longer side and over the shorter side as the corner of rectangular footing is being approached where the direction of soil motion remains normal to each corresponding side respectively. The failure mechanism under moment loading comprises a plane strain scoop sliding mechanism over the central part of the longer side, and the radius of scoop sliding mechanism increases linearly at the ends of the longer side. On the basis of the kinematic failure mechanisms mentioned above, the vertical ultimate bearing capacity and the ultimate bearing capacity against moment or moment ultimate bearing capacity are obtained by use of upper bound limit analysis theory. At the same time, numerical analysis results, Skempton＇ s results and Salgado et al. ＇s results are compared with this upper bound solution. It shows that the presented failure mechanisms and plastic limit analysis predictions are validated. In order to investigate the behaviors of undrained clay foundation beneath the rectangular footing subjected to the combined loadings, numerical analysis is adopted by virtue of the general-purpose FEM software ABAQUS, where the clay is assumed to obey the Mohr-Coulomb yielding criterion. The failure envelope and the ultimate bearing capacity are achieved by the numerical analysis results with the varying aspect ratios from length L to breadth B of the rectangular footing. The failure mechanisms of rectangular footing which are subjected to the combined vertical loading V and horizontal loading H （Vertical loading V and moment loading M, and horizontal loading H and moment loading M respectively are observed in the finite e 相似文献
15.
The influence of non-coaxial constitutive model on predictions of dense sand behavior is investigated in this paper. The non-coaxial model with strain softening plasticity is applied into finite-element program ABAQUS, which is first used to predict the stress-strain behavior and the non-coaxial characteristic between the orientations of the principal stress and principal plastic strain rate in simple shear tests. The model is also used to predict load settlement responses and bearing capacity factors of shallow foundations. A series of centrifuge tests for shallow foundations on saturated dense sand are performed under drained conditions and the test results are compared with the corresponding numerical results. Various footing dimensions, depths of embedment, and footing shapes are considered in these tests. In view of the load settlement relationships, the stiffness of the load-displacement curves is significantly affected by the non-coaxial model compared with those predicted by the coaxial model, and a lower value of non-coaxial modulus gives a softer response. Considering the soil behavior at failure, the coaxial model predictions of bearing capacity factors are more advanced than those of centrifuge test results and the non-coaxial model results;besides, the non-coaxial model gives better predictions. The non-coaxial model predictions are closer to those of the centrifuge results when a proper non-coaxial plastic modulus is chosen. 相似文献
16.