共查询到20条相似文献，搜索用时 46 毫秒
1.
2.
城市污水与海水混合过程中有机污染物的转移 总被引：5，自引：2，他引：5
以３种不同混合体系模拟研究了城市污水与海水混合过程中有机污染物的转移。在“污水颗粒物－过滤海水”体系中，颗粒态有机物有一定的释放，释放率约在０．０２－０．０４ｄ－１之间。释放过程可用交换平衡动力学模式描述。在“天然海水－过滤污水”和“海水－污水”给 体系中，未发现有机污染和有明显的吸附或释放。在这３种混合体系中均发现化学耗氧量（ＣＯＤ）的降解现象，降解过程符合一级动力学方程，降解速率常数在０．０４ 相似文献
3.
本文模拟研究了污水颗粒物－海水体系中磷的转移过程。污水颗粒物与海水混合之后先是快速吸附磷，之后即以约０．３ｄ＾－１的速率进行释放。总过程仍表现为磷的释放。磷的吸附－释放属于离子交换性质，可用交换平衡动力学模式表示。溶解磷含量的增加速率符合一级动力学方程。 相似文献
4.
纳污海水中COD生化降解过程的模拟试验研究 总被引：6，自引：0，他引：6
1995年5－11月期间,采取渤海湾海水,控制不同的试验水温和不同的有机物起始浓度,采用试验室模拟方法,测定COD生化降解曲线。依据COD降解动力学理论,得出不同环境条件下的COD生化降解动力学参数。经过归纳综合,建立了纳污海水中COD的生化降解动力学参数方程式。试验结果显示,渤海湾天津近岸排海污水COD生化降解过程符合一级反应动力学模型,其降解速率系数足值介于0．023－O．076d-1之间。k值受温度变化的影响较大,温度越高,k值越大。 相似文献
5.
１９９５年５￣１１月期间,采取渤海湾海水,控制不同的试验水温和不同的有机物起始浓度,采用试验室模拟方法,测定ＣＯＤ生化降解曲线,依据ＣＣＤ降解动力学理论,得出了不同环境条件下的ＣＯＤ生化降解动力学参数,经过归纳综合,建立了纳污海水中ＣＯＤ的生化降解动力学参数方程式,试验结果显示,渤海湾天津近岸排海污水ＣＯＤ生化降解过程符合一级反应动力学模型,其降解速率系数ｋ值介于０．０２３￣０．０７６ｄ＾－１之间 相似文献
6.
污水与九龙江河口水混合研究表明，ＣＯＤ的降解符合一级动力学模式，降解速率常数ｋ在０．０４－０．１１ｄ＾－１之间，水体有机物的转移以降解作用为主；两种水体混合时，先产生磷的吸附，后释放，整个过程表现为颗业磷向溶解无机磷的转移。 相似文献
7.
目前污水排海是解决我国沿海城市污水出路问题的优选方案。针对青岛市经济技术开发区污水排海方案，利用浅海动力学和物质输运数值模型，对排污的环境影响进行了数值预测，确定了排污口离岸距离的可接受范围。依据保护目标要求的水质条件，对污水的预处理提出了建议。 相似文献
8.
9.
根据2021年威海西北部污水排海口附近海域水质监测结果，对海水水质现状进行了评价；结合2007年调查水质监测结果和2017—2021年连续监测数据，分析了污水排放前后和近年附近海域海水水质的变化趋势；采用Mike 3三维潮流和污染物扩散耦合模型，预测了污水排放量增加(提量)、污染物排放标准提高(提标)后排放污水中COD、无机氮、活性磷酸盐对海洋环境的影响范围和程度。结果表明：研究区海水水质较2007年略有下降，但排水口处及外侧海域大部分站位符合海水水质二类标准，海水水质状况相对较好，威海污水处理厂多年污水离岸深水达标排放对区域海洋环境的影响较小。污水处理厂提量、提标改造后，特征因子中仅无机氮扩散范围略超原污水排放混合区用海范围，不会对研究区水质环境造成明显影响。 相似文献
10.
11.
Coastal inundation associated with extreme sea levels is the main factor which leads to the loss of life and property whenever a severe tropical cyclonic storm hits the Indian coasts. The Andhra and Orissa coasts are most vulnerable for coastal inundation due to extreme rise in sea levels associated with tropical cyclones. Loss of life may be minimized if extreme sea levels and associated coastal flooding is predicted well in advance. Keeping this in view, location specific coastal inundation models are developed and applied for the Andhra and Orissa coasts of India. Several numerical experiments are carried out using the data of past severe cyclones that struck these regions. The simulated inland inundation distances are found to be in general agreement with the reported flooding. 相似文献
12.
Chandralata Raghukumar G. Sheelu P. A. Loka Bharathi Shanta Nair C. Mohandass 《Marine Georesources & Geotechnology》2001,19(1):1-16
In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance. 相似文献
13.
This study tests the hypothesis that the in situ void ratio of surficial marine sediments may be predicted from shear wave velocity-depth data with a reliability equal to that of other methods currently available. Shear wave velocity is fundamentally controlled by the number of grain-to-grain contacts per unit volume of material and by the effective stress across those contacts. In this study, three previously established empirical formulae are used to predict void ratio from velocity-depth data. Field data were acquired along a transect off the northern Californian coast across which water depth increased from 35 to 70 m and seafloor sediment type varied from sand to silty-sand, respectively. A towed seafloor sled device was used to collect shear wave refraction data, and a marked, systematic decrease in velocity was observed along the line, ranging from 35-70 m/s for the coarse, near-shore material to 25-40 m/s for the finer, offshore deposits. Void ratios predicted from these velocities were compared with data measured directly from box-core samples. Of the formulae used for prediction, two agree remarkably well with the control data. Both predicted and control values increase from 0.6-0.8 for the sandy material to 1.1-1.5 for the silty-sand. Thus, this study does not disprove the hypothesis set and demonstrates the potential of field shear wave velocity-depth data as a means of delineating spatial variation in void ratio for surficial marine sediments in a remote, nondestructive manner. 相似文献
14.
Hoi-Soo Jung Kap-Sik Jeong Yong-Shik Chu Sung-Hyun Park Ki-Hyune Kim 《Marine Georesources & Geotechnology》2001,19(3):181-195
Grain size and water content in box-core sediments from the Clarion-Clipperton fracture zone (C-C zone) in the northeast equatorial Pacific were analyzed in detail to understand the downcore variations across a hiatus between Quaternary and Tertiary layers. Grain-size distributions in the topmost core sediments show two modes: a coarse mode (peaked at 50 μm) and a fine mode (at 2-25 μm). The coarse mode disappears gradually with depth accompanied by the dissolution of siliceous fossil tests, whereas the fine mode coarsens due to the formation of authigenic minerals. Water content increases abruptly across a color boundary between an upper pale brown layer and a lower dark brown layer that is the hiatus between Quaternary and Tertiary layers. Abundant smectites and microvoid molds, which are created by the prolonged fossil dissolution in the underlying sediment, are attributed for the abrupt downcore variation of water content. Overall variations in grain size and water content in the topmost core sediments in the western C-C zone are possibly constrained by the dissolution of biogenic siliceous fossils. Variations in geotechnical properties related to these changes must be considered in the design of nodule collectors. 相似文献
15.
Shigehisa Nakamura 《Marine Geodesy》2001,24(1):27-33
This article concerns an interrelation between the sea levels and the western boundary flow near a tectonic boundary in a local zone in the Northwestern Pacific. In this zone, sea level variations at stations located on the coast facing the Pacific are studied to find the interrelation between variations of the Kurosio flow as an index of the distance of the flow axis off a specific coast. The result is discussed after data processing of the monthly means of the sea levels, and a notice is taken of variations caused by active crustal upheavals during a seismic event, a local earthquake. 相似文献
16.
Particulate samples were collected from the Changjiang river system during a flood period, in May 1997, and POC, stable isotope and lipids associated with particles were examined. Results showed the decrease (0.84% ～ 1.88%) of organic carbon content from the upper reaches to the estuary.δ13C values of particulate organic carbon was in the range of -24.9×10-3 to -26.6×10-3, which were close to the isotopic signature of continental C3 vegetation. Total particulate n-alkanes concentrations varied from 1.4 to 10.1μg/dm3,or from 23.7 to 107μg/g of total suspended matter. Fatty acids were present in all the samples, from 1.4 to 5.4μg/dm3, with saturated and unsaturated straight-chain and branched compounds in the carbon number range from C12 to C30. Both δ13C and the ratio of carbon content to nitrogen content indicate the predominance of terrestrial inputs (soil organic matter) among the particles. The biomarker approach has been used to identify the relative portion of terrigenous and autochthonous fraction in the particulate samples. The distribution of fatty acids suggests a striking phytoplanktonic and microbial signal in most particle samples. The terrestrial alkanes are used to estimate the contribution of terrestrial inputs along the mainstream. 相似文献
17.
海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。 相似文献
18.
Andrzej Chybicki 《Marine Geodesy》2018,41(1):1-23
Current trends of development of satellite derived bathymetry (SDB) models rely on applying calibration techniques including analytical approaches, neuro-fuzzy systems, regression optimization and others. In most of the cases, the SDB models are calibrated and verified for test sites, that provide favorable conditions for the remote derivation of bathymetry such as high water clarity, homogenous bottom type, low amount of sediment in the water and other factors. In this paper, a novel 3-dimensional geographical weighted regression (3GWR) SDB technique is presented, it binds together methods already presented in other studies, the geographically weighted local regression (GWR) model, with depth dependent inverse optimization. The proposed SDB model was calibrated and verified on a relatively difficult test site of the South Baltic near-shore areas with the use of multispectral observations acquired by a recently launched Sentinel-2 satellite observation system. By conducted experiments, it was shown that the proposed SDB model is capable of obtaining satisfactory results of RMSE ranging from 0.88 to 1.23[m] depending on the observation and can derive bathymetry for depths up to 12m. It was also shown, that the proposed approach may be used operationally, for instance, in the continuous assessment of temporal bathymetry changes, for areas important in the context of ensuring local maritime safety. 相似文献
19.
N. H. Khadge 《Marine Georesources & Geotechnology》2000,18(3):251-258
As a part of the environmental impact assessment studies, geotechnical properties of sediments were determined in the Central Indian Basin. The undrained shear strength and index properties of the siliceous sediments were determined on 20 box cores of uniform dimension collected from various locations in five preselected sites. The maximum core length encountered was 41 cm and most of the sediments were siliceous oozes consisting of radiolarian or diatomaceous tests. The shear strength measurements revealed that surface sediments deposited in recent times (0-10 cm) have a shear strength of 0-1 kPa; this value increases with depth, reaching 10 kPa at 40 cm deep. Older sediments have greater strength because of compaction. Water content varies in the wide range of 312-577% and decreases with depth. The clay minerals such as smectite and illite are dominant and show some control over water content. Wet density, specific gravity, and porosity do not indicate any notable variation with depth, thereby indicating a uniform, slow rate of sedimentation. The average porosity of sediments is 90.2%, specific gravity 2.18, and wet bulk density 1.12 g/cm 3 . Sediments exhibit medium to high plasticity characteristics, with the average plasticity index varying between 105% and 136%. Preliminary studies on postdisturbance samples showed an increase in natural water content and a decrease in undrained shear strength of sediments in the top 10- to 15-cm layer. 相似文献
20.
An Improved Calibration of Satellite Altimetric Heights Using Tide Gauge Sea Levels with Adjustment for Land Motion 总被引：2，自引：0，他引：2
Gary T. Mitchum 《Marine Geodesy》2000,23(3):145-166
Several major improvements to an existing method for calibrating satellite altimeters using tide gauge data are described. The calibration is in the sense of monitoring and correcting temporal drift in the altimetric time series, which is essential in efforts to use the altimetric data for especially demanding applications. Examples include the determination of the rate of change of global mean sea level and the study of the relatively subtle, but climatically important, decadal variations in basin scale sea levels. The improvements are to the method described by Mitchum (1998a), and the modifications are of two basic types. First, since the method depends on the cancellation of true ocean signals by differencing the altimetric data from the tide gauge sea level time series, improvements are made that produce a more complete removal of the ocean signals that comprise the noise for the altimetric drift estimation problem. Second, a major error source in the tide gauge data, namely land motion, is explicitly addressed and corrections are developed that incorporate space-based geodetic data (continuous GPS and DORIS measurements). The long-term solution, having such geodetic measurements available at all the tide gauges, is not yet a reality, so an interim solution is developed. The improved method is applied to the TOPEX altimetric data. The Side A data (August 1992?February 1999) are found to have a linear drift component of 0.55 + / 0.39 mm/yr, but there is also a significant quadratic component to the drift that is presently unexplained. The TOPEX Side B altimeter is estimated to be biased by 7.0 + / 0.7 mm relative to the Side A altimeter based on an analysis of the first 350 days of Side B data. 相似文献