首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 31 毫秒
1.
Head-wave parametric rolling of a surface combatant   总被引：1，自引：0，他引：1  
Complementary CFD, towing tank EFD, and nonlinear dynamics approach study of parametric roll for the ONR Tumblehome surface combatant both with and without bilge keels is presented. The investigations without bilge keels include a wide range of conditions. CFD closely agrees with EFD for resistance, sinkage, and trim except for Fr>0.5 which may be due to free surface and/or turbulence modeling. CFD shows fairly close agreement with EFD for forward-speed roll decay in calm water, although damping is over/under predicted for largest/smaller GM. Most importantly CFD shows remarkably close agreement with EFD for forward-speed parametric roll in head waves for GM=0.038 and 0.033 m, although CFD predicts larger instability zones at high and low Fr, respectively. The CFD and EFD results are analyzed with consideration ship motion theory and compared with Mathieu equation and nonlinear dynamics approaches. Nonlinear dynamics approaches are in qualitative agreement with CFD and EFD. The CFD and nonlinear dynamics approach results were blind in that the actual EFD radius of gyration kxx was not known a priori.  相似文献   

2.
Tim Gourlay 《Ocean Engineering》2009,36(14):1119-1127
  相似文献   

3.
Squat effects on high speed craft in restricted waterways   总被引：1，自引：0，他引：1  
K.S. Varyani   《Ocean Engineering》2006,33(3-4):365-381
The vessels considered here for the squat studies are a bulk carrier and an High Speed Craft (HSC). The bulk carrier of full form (CB=0.81) is used for validation purpose and subsequently the numerical computations are performed for a High Speed Craft with fine hull form of CB=0.467. A high speed ferry, with LCB and LCF quite aft of midship is considered for squat study. For a vessel speed of above 6.0 knots and for a waterway width greater than the vessel length there appears to be a sudden increase in sinkage at the stern accompanied by a large value of bow emergence. It could be seen that the speed of the vessel has a much greater influence on the sinkage and trim of the vessel than the waterway restrictions.  相似文献   

4.
A practical method to account for the influence of sinkage and trim on the drag of a freely floating (free to sink and trim) common monohull ship at a Froude number F ≤ 0.45 is considered. The sinkage and the trim are estimated via two alternative simple methods, considered previously. The drag is also estimated in a simple way, based on the classical Froude decomposition into viscous and wave components. Specifically, well-known semiempirical expressions for the friction drag, the viscous pressure drag and the drag due to hull roughness are used, and the wave drag is evaluated via a practical linear potential flow method. This simple approach can be used for ship models as well as full-scale ships with smooth or rough hull surfaces, and is well suited for early ship design and optimization. The method considered here to determine the sinkage and the trim, and their influence on the drag, yields theoretical predictions of the drag of the Wigley, S60 and DTMB5415 hulls that are much closer to experimental measurements than the corresponding predictions for the hull surfaces of the ships in equilibrium position at rest. These numerical results suggest that sinkage and trim effects, significant at Froude numbers 0.25 < F, on the drag of a typical freely floating monohull ship can be realistically accounted for in a practical manner that only requires simple potential flow computations without iterative computations for a sequence of hull positions.  相似文献   

5.
CFD and system-based simulation are used to predict broaching, surf-riding, and periodic motion for the ONR Tumblehome model, including captive and free model test validation studies. CFD shows close agreement with EFD for calm water resistance, static heel (except for sway force and yaw moment), and static drift (except for roll moment). CFD predictions of static heel in following waves also compare well with EFD except for surge force, sway force, and pitch angle. Froude-Krylov calculations of wave-induced surge force in following waves provides good agreement for high Froude number, but significantly overestimates for Froude number less than 0.2. On the other hand, CFD successfully reproduces the reduction of the wave-induced surge force near Froude number 0.2, probably because CFD can capture the 3D wave pattern. CFD free model simulations are performed for several speeds and headings and validated for the first time for surf-riding, broaching, and periodic motions. System-based simulations are carried out based on inputs from EFD, CFD, and Froude-Krylov for a dense grid of speeds and headings to predict the instability map, which were found to produce fairly similar results.  相似文献   

6.
Maneuverability is an important aspect of marine vehicle design. The performance of a rudder, as the most important means of maneuvering, has significant impacts on ship controllability characteristics. This study investigated the effect of five rudder profiles (NACA 0012, NACA0025, IFS, Fish tail, HSVA) on the turning characteristics of KCS containership model. This investigation was performed by direct simulation of the ship turning circle maneuver in computational fluid dynamic environment based on the ITTC verification procedure. All rudders were defined with the same lateral area. Simulations were conducted with the commercial software STAR-CCM+. The rudder turning and the ship's dynamic motion were modeled by the use of an overset technique and six-DOF dynamic solver, respectively. Roll, pitch and heave motions and forward speed reduction during the turning maneuver with different rudders were computed and compared. Results show that the rudder profiles designed specifically for marine applications (Fishtail, IFS and HSVA) perform better than the traditional NACA series.  相似文献   

7.
This study investigates the dynamic response of a Triangular Configuration Tension Leg Platform (TLP) under random sea wave loads. The random wave has been generated synthetically using the Monte-Carlo simulation with the Peirson–Moskowitz (P–M) spectrum. Diffraction effects and second-order wave forces have not been considered. The evaluation of hydrodynamic forces is carried out using the modified Morison equation with water particle kinematics evaluated using Airy's linear wave theory. Wave forces are taken to be acting in the surge degree-of-freedom. The effect of coupling of various structural degrees-of-freedom (surge, sway, heave, roll, pitch and yaw) on the dynamic response of the TLP under random wave loads is studied. Parametric studies for random waves with different Hs and Tz under the presence of current have also been carried out. For the orientation of the TLP, surge, heave and pitch degrees-of-freedom responses are influenced significantly. The surge power spectral density function (PSDF) indicates that the mean square response is affected by the amplification at the natural frequency of the surge degree-of-freedom and also at the peak frequency of the wave loading. The PSDF of the heave response shows higher peak values near the surge frequency and near the peak frequency of the wave loading. Surge response, therefore, influences heave response to the maximum. Variable submergence seems to be a major source of nonlinearity and significantly enhances the responses in surge, heave and pitch degrees-of-freedom. In the presence of current, the response behaviour of the TLP is altered significantly introducing a non-zero mean response in all degrees-of-freedom.  相似文献   

8.
An attempt is made to find a relation betweenK, the absolute value of accumulation-dispersal coefficient of marine organisms referred to a region or a group (Kawai, 1986a), andL, the square root of the area of the region or the group over which the distribution density of organisms is averaged.K is estimated as shown below. For appropriate sampling time-intervals,K becomes greater than other coefficients such as population growth coefficient. Using this result, an order of magnitude ofK dependent onL is estimated from various data of temporal change in density. With the aid of a dependenceQL –2/3 (Kawai, 1985b), a relationKL –2/3 is predicted for 30 cmL 30 km, whereQ andK are the root-mean-square values of area-averaged horizontal divergence of near-surface flows and of the accumulation-dispersal coefficient, respectively. The reason whyK tends to have the order of magnitude of weak or mediumQ is discussed. The doubling-halving time of the distribution density due to accumulation-dispersal,T, is related toK byT=(loge2)/¦K¦L 2/3. Finally, sampling time-intervals to estimate accumulation-dispersal coefficients are referred to.  相似文献   

9.
The characteristics of the flow over the rudder’s pintle gap are investigated by using the particle image velocimetry (PIV) technique. The propeller and rudder models are scaled down to 1/28.5. Highly accelerated leakage outflows are separated at the discontinuities of the gap and generate strong cavitation at the suction side of the rudder. In the rudder and propeller configuration, the propeller wake sheet ahead of the gap entrance region starts to induce leakage flow over the lower pintle gaps of the suction side. The gap flow has a velocity magnitude as high as 0.4U0 in the high leakage flow condition, where the wake sheet locates over the gap entrance. The cross-flow of the propeller wake sheet interferes the gap entrance region and triggers gap cavitation. As the propeller wake sheet moves downstream and weakens, the gap flow velocity decreases over the gap entrance.  相似文献   

10.
A dynamic marine propeller simulation system was developed, which is utilized for meeting the experimental requirement of theory research and engineering design of marine electric propulsion system. By applying an actual ship parameter and its accurate propeller J’~ KT’ and J’~KP’ curve data, functional experiments based on the simulation system were carried out. The experiment results showed that the system can correctly emulate the propeller characteristics, produce the dynamic and steady performances of the propeller under different navigation modes, and present actual load torque for electric propulsion motor.  相似文献   

11.
In order to study the propulsion mechanism of the bionic flapping hydrofoil (BFH), a 2-DoF (heave and pitch) motion model is formulated. The hydrodynamic performance of BFH with a series of kinematical parameters is explored via numerical simulation based on FLUENT. The calculated result is compared with the experimental value of MIT and that by the panel method. Moreover, the effect of inlet velocity, the angle of attack, the heave amplitude, the pitch amplitude , the phase difference, the heave biased angle, the pitch biased angle and the oscillating frequency are investigated. The study is useful for guiding the design of bionic underwater vehicle based on flapping propulsion. It is indicated that the optimal parameters combination is v=0.5m/s, θ0=40°.θ0=30°,Ψ=90°,Фbias=0°,θbias=0°and f=0.5Hz .  相似文献   

12.
The scope of this paper is to develop the nonlinear meta-models for seakeeping behaviour, considering the fishing vessels. These models are intended to be inserted either in a multiattribute design selection process or in a comprehensive multiobjective optimization procedure. For this purpose, seakeeping data of fishing vessels in regular head waves are used to develop meta-models of transfer functions of heave, pitch and vertical acceleration by nonlinear analysis. A home-made software considers two databases; the first is composed by the ship dimensions and coefficients of fishing vessels, and the second is their ship motion data obtained by employing a strip-theory calculation. The meta-models are proposed to predict the vertical motion characteristics for given ranges of speed and wave length during the concept design stage. The independent variables are hull size (Δ), main dimensions (L, B, T), and some hydrostatic parameters (CWP, CVP, LCB, LCF, etc.). The results estimated by the software show good correspondences with the ones achieved by direct computations. The study provides additional insight on the influence of hull form parameters on seakeeping performance of small vessels having form properties and parametric range corresponding to the investigated vessels.  相似文献   

13.
A numerical study was undertaken in order to assess the capability of an unsteady RANS code to predict the seakeeping characteristics of a high-speed multi-hull vessel in high sea states. Numerical analysis includes evaluation of ship motions, effects of wave steepness on ship response, catamaran natural frequency and added resistance in waves. Computations were performed for the DELFT 372 catamaran by the URANS solver CFDSHIP-Iowa V.4. The code was validated with encouraging results for high ship speeds (0.3≤Fn≤0.75) and high wave amplitudes (0.025≤Ak≤0.1). Comparison with strip theory solutions shows that the RANS method predicts ship motions with higher accuracy and allows the detection of nonlinear effects. Current computations evidence that heave peaks occur at resonance for all Fn, and reach the absolute maximum at Fn=0.75. Maximum pitch occurs at frequencies lower than resonance, for each speed, and absolute maximum occurs at medium Fn=0.6. Maximum added resistance, Raw, was computed at Fn=0.45, which, interestingly, is near the catamaran Fncoincidence. Overall, we found similar results as Simonsen et al. (2008) for KCS containership, though, herein, a multi-hull geometry and higher speeds were tested. Also, our results are useful to further evaluate the exciting forces and their correlation with fe and λ/Lpp.  相似文献   

14.
The use of an unsteady computational fluid dynamic analysis of the manoeuvring performance of a self-propelled ship requires a large computational resource that restricts its use as part of a ship design process. A method is presented that significantly reduces computational cost by coupling a blade element momentum theory (BEMT) propeller model with the solution of the Reynolds averaged Navier Stokes (RANS) equations. The approach allows the determination of manoeuvring coefficients for a self-propelled ship travelling straight ahead, at a drift angle and for differing rudder angles. The swept volume of the propeller is divided into discrete annuli for which the axial and tangential momentum changes of the fluid passing through the propeller are balanced with the blade element performance of each propeller section. Such an approach allows the interaction effects between hull, propeller and rudder to be captured. Results are presented for the fully appended model scale self-propelled KRISO very large crude carrier 2 (KVLCC2) hull form undergoing static rudder and static drift tests at a Reynolds number of 4.6×106 acting at the ship self-propulsion point. All computations were carried out on a typical workstation using a hybrid finite volume mesh size of 2.1×106 elements. The computational uncertainty is typically 2–3% for side force and yaw moment.  相似文献   

15.
The main idea of this paper is to identify functional relations between seakeeping characteristics and hull form parameters of Mediterranean fishing vessels. Multiple regression analysis is used for quantitative assessment through a computer software that is based on the SQL Server Database. The seakeeping attributes under investigation are the transfer functions of heave and pitch motions and of absolute vertical acceleration at stern, while the ship parameters influencing motion dynamics have been classified into two groups: displacement (Δ) and main dimensions (L, B, T), coefficients that define the details of the hull form (CWP, CVP, LCB, LCF, etc.).Four multiple regression models having different parameter combinations are here investigated and discussed, giving way to the so-called ‘Simple Model’, ‘Intermediate Model’, ‘Enhanced 1 Model’ and ‘Enhanced 2 Model’. The obtained results are more than satisfactory for seakeeping predictions during the conceptual design stage.  相似文献   

16.
A computational method has been developed to predict the hydrodynamic performance of the propeller–rudder systems (PRS) and azimuthing podded drive (AZIPOD) systems. The method employs a vortex-based lifting theory for the propeller and the potential surface panel method for the steering system. Three propeller models along with three steering systems (rudder and strut, flap and pod (SFP)) are implemented in the present calculations for the cases of uniform and non-uniform conditions. Computed velocity components show good agreement with the experimental measurements behind a propeller with or without the rudder. Calculated thrust, torque and lift also agree well with the experimental results. Computations are also performed for an AZIPOD system in order to obtain the pressure distributions on the SFP, and the hydrodynamic performance (thrust, torque and lift coefficients). The present method is useful for examining the performance of the PRS and AZIPOD systems in the hope of estimating the propulsion and the maneuverability characteristics of the marine vehicles more accurately.  相似文献   

17.
In practical maritime conditions, ship hulls experience heave motion due to the action of waves, which can further drive the ship’s propellers to oscillate relative to the surrounding water. In order to investigate the motion of a propeller working behind a surface vessel sailing in waves, a numerical simulation is conducted on a propeller impacted by heave motion in cavitating flow using the Reynolds-averaged Navier-Stokes (RANS) method. The coupling of the propeller’s rotation and translation is fulfilled using equations of motion defined for this purpose. The heave motion is simplified as a periodic motion based on a sinusoidal function. The numerical transmission of information from the unsteady flow field is achieved using the overset grid approach. In this manner, the unsteady thrust coefficient and torque coefficient of propellers in different periods of heave motion are analyzed. A comparative study is implemented on the unsteady cavitation performance and wake characteristics of propeller. With the propeller’s heave motion, the flow field non-uniformity constantly changes the load on the propeller during each revolution period and each heaving period, the propeller load and the wake field are closely related to the variation of heave motion period. The results obtained from the numerical simulation are expected to serve as a useful theoretical reference for the numerical analysis of a propeller in a heave motion.  相似文献   

18.
The present investigation focuses on the effects of the stern appendages and the propulsion system on the hydro-loads generated by the propeller during off-design conditions, with particular emphasis on the in-plane components. Recent experimental investigations carried out by free running model tests [7], [8] and CFD analysis [5] for a modern twin screw model, highlighted that maneuvers at small drift angles and yaw rates might be as critical as the tighter ones due to complex propeller-wake interactions. Therefore, design criteria should take into account also these operative conditions, in order to reduce the effects of propeller-wake interaction phenomena that degrade the overall propulsive efficiency, induce shaft/hull structural vibration and increase noise emission. In the present study we analyze the effects of geometric and propulsive modifications with respect to the twin screw configuration studied in [5]. In particular, the effect of the centreline skeg, propeller direction of rotation and control strategies of the propulsion plant on the propeller bearing loads have been investigated from the analysis of the nominal wake in maneuvring conditions, computed by unsteady RANSE simulations coupled with a propeller model based on Blade Element Theory. The considered test cases were turning circle maneuvers with different rudder angles at FN = 0.265.  相似文献   

19.
On the basis of the analysis of the data of hydrological observations, we construct an empirical dependence of the vertical heat fluxQ on the temperature gradientT z . The integral advective-diffusive transfer is taken into account by the method of Kolesnikov. We obtain a generalized dependence of the coefficient of vertical thermal diffusivityK z onT z and note that the well-known Rossby-Montgomery relation and Kolesnikov formula are its special cases. We analyze the possibility of application of this dependence to linear and nonlinear problems of thermal conductivity and diffusion in the ocean. Translated by Peter V. Malyshev and Dmitry V. Malyshev  相似文献   

20.
合理的刚度和潜深设计可以使升沉水平板获得优异的消浪性能。基于考虑流体黏性的二维不可压缩Navier-Stokes方程,以高阶紧致插值CIP(constrained interpolation profile)方法求解方程对流项,采用VOF(volume of fluid)方法重构自由液面,构建二维数值波浪水槽。采用试验数据验证模型后,研究孤立波与升沉水平板相互作用,分析相对刚度K*、相对潜深d/h、相对波高H/h对于升沉板的消浪性能和运动响应的影响,揭示升沉板对孤立波的消浪机理。研究表明:在孤立波通过时,升沉板会经历一个先上升后下降的运动,随后非线性自由振动,板下方水体近似均匀流动,且水流的垂向流动与板的垂荡方向一致;升沉板主要通过不对称涡旋脱落、浅水变形、波浪反射与辐射波转化等方式消耗孤立波能量;一定条件下,采用最优相对刚度K*=4.0和最优相对潜深d/h=0.52可以取得良好的消浪效果,此时透射系数最小,同时升沉板的运动响应在合理的范围内。  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号