共查询到20条相似文献，搜索用时 31 毫秒
1.
Numerical models which account for the multiple response modes of floating wave energy converters (WECs) in operating conditions require experimental data for validation. Measurement and observation of complex hydrodynamic mechanisms are also required to inform the development of modelling tools suitable for the simulation of response to extreme waves. Experimental measurements are reported of the motion of an axisymmetric float to regular and near-focused waves. The mechanical system, incident wave conditions and response in a 2D vertical plane are detailed to facilitate comparison to numerical simulations. The system comprises a heaving float connected to a counterweight by an inextensible cable over two pulleys to provide a simplified representation of the slowly varying surge constraint of a mooring system. Translation of the float is measured using an optical encoder. Motion in heave, surge and pitch are also determined by a position identification method based on analysis of video footage. For low frequency regular waves, the float prescribes an elliptical trajectory and the variation of response amplitude with wave amplitude is linear. At higher frequencies, drift of up to one-third of the float radius is observed and the float oscillates along an arc. More complex motions are observed due to the three large amplitude waves of a near-focused wave group. During these waves the upper surfaces of the float are partly immersed and motion occurs in heave, surge and pitch. 相似文献
2.
The present paper describes a mathematical model in which the fluid motion inside a U-tank is nonlinearly coupled to the heave, roll and pitch motions of the ship. The main purpose of the investigation is centred on the control of roll motion in the case of parametric resonance in longitudinal waves. A transom stern small vessel, known to be quite prone to parametric amplification, is employed in the study. Four tank designs are employed in order to study the influence of tank mass, tank natural frequency and tank internal damping on the control of parametric rolling at different head seas conditions. Additionally, the influence of the vertical position of the tank is also investigated. The main results are presented in the form of limits of stability, with encounter frequency and wave amplitudes as parameters. Distinct dynamical characteristics are discussed and conclusions are drawn on the relevant parameters for the efficient control of the roll amplifications in head seas. 相似文献
3.
合理的刚度和潜深设计可以使升沉水平板获得优异的消浪性能。基于考虑流体黏性的二维不可压缩Navier-Stokes方程,以高阶紧致插值CIP(constrained interpolation profile)方法求解方程对流项,采用VOF(volume of fluid)方法重构自由液面,构建二维数值波浪水槽。采用试验数据验证模型后,研究孤立波与升沉水平板相互作用,分析相对刚度K*、相对潜深d/h、相对波高H/h对于升沉板的消浪性能和运动响应的影响,揭示升沉板对孤立波的消浪机理。研究表明:在孤立波通过时,升沉板会经历一个先上升后下降的运动,随后非线性自由振动,板下方水体近似均匀流动,且水流的垂向流动与板的垂荡方向一致;升沉板主要通过不对称涡旋脱落、浅水变形、波浪反射与辐射波转化等方式消耗孤立波能量;一定条件下,采用最优相对刚度K*=4.0和最优相对潜深d/h=0.52可以取得良好的消浪效果,此时透射系数最小,同时升沉板的运动响应在合理的范围内。 相似文献
4.
Point absorber wave energy device with multiple degrees of freedom (DOF) is assumed to have a better absorption ability of mechanical energy from ocean waves. In this paper, a coaxial symmetric articulated point absorber wave energy converter with two degrees of freedom is presented. The mechanical equations of the oscillation buoy with power take-off mechanism (PTO) in regular waves are established. The three-dimensional numerical wave tank is built in consideration of the buoy motion based upon the CFD method. The appropriate simulation elements are selected for the buoy and wave parameters. The feasibility of the CFD method is verified through the contrast between the numerical simulation results of typical wave conditions and test results. In such case, the buoy with single DOF of heave, pitch and their coupling motion considering free (no PTO damping) and damped oscillations in regular waves are simulated by using the verified CFD method respectively. The hydrodynamic and wave energy conversion characteristics with typical wave conditions are analyzed. The numerical results show that the heave and pitch can affect each other in the buoy coupling motion, hydrodynamic loads, wave energy absorption and flow field. The total capture width ratio with two coupled DOF motion is higher than that with a single DOF motion. The wave energy conversion of a certain DOF motion may be higher than that of the single certain DOF motion even though the wave is at the resonance period. When the wave periods are high enough, the interaction between the coupled DOF motions can be neglected. 相似文献
5.
共振运动是深海浮式平台设计的关键考虑因素之一,对海洋平台的作业具有重要影响。采用半潜式平台运动的非线性耦合数学模型,考虑浮筒和横撑出入水以及垂荡、横摇和纵摇运动耦合对平台浮力和恢复力的影响,研究半潜式平台非线性共振运动特性,以及不规则波浪参数对运动的影响。研究表明:在非线性耦合运动和浮力变化的影响下,半潜式平台纵摇和垂荡运动的固有周期会随运动幅值的增大而逐渐减小,且最终趋于稳定,对纵摇运动周期的影响更为显著;非线性效应会使半潜式平台产生显著的低频纵摇共振响应,以及共振频率漂移的现象,且受随机种子和波浪周期的影响较小。 相似文献
6.
A ring-shaped spar-type Very Large Floating Structure (VLFS) is proposed as an intermediate base for supporting deepwater resource exploitation far away from the coast line. The proposed VLFS is composed of eight rigidly connected deep-draft spar-type modules and an inside harbor. A double-layered perforated-wall breakwater is vertically attached to the VLFS and pierces through the water surface to attenuate the wave energy in the inside harbor. The hydrodynamic performance characteristics of the ring-shaped VLFS was experimentally evaluated in the present study, focusing on the motion responses, wave elevations, and wave run-ups. The natural periods of the motions in vertical plane were determined to be larger than 40 s, which is much larger than common wave periods. This enhanced the motion performance in vertical plane and afforded favorable habitation and operation condition on the VLFS. A large surge damping was induced by the vertical breakwater, which tended to significantly affect the surge and pitch motions, but had a negligible effect on the heave motion. The component frequencies of the wave elevations in the inside harbor and the wave run-ups were identical with those of the incident waves. The wave attenuation was frequency-dependent and effective for the common wave frequencies, with a smaller loss coefficient observed in higher sea state. The wave attenuation and wave run-ups tended to improve in the absence of the leeward walls. 相似文献
7.
针对张力腿系泊浮式风力机的基础运动,忽略柔性构件的影响,建立气动—水动—系泊非线性耦合运动方程。在运动控制方程中包含张力腿系泊系统的非线性回复刚度,桨距角控制以及浮式基础运动对空气动力载荷的影响。在波浪载荷的计算中考虑二阶波浪载荷的作用。采用随机频率相位角调制法生成畸形波波面时历,计算在畸形波作用下张力腿型浮式风力机的动力响应特性。数值模拟结果表明,在畸形波作用下,浮式基础的运动及空气动力性能均受到了显著的影响。其中浮式基础的纵荡和纵摇运动分别受二阶差频与和频波浪力的影响,而垂荡运动的增加则主要是受下沉运动的影响。在畸形波经过的时刻,风力机的功率系数迅速下降,水平方向的风载荷波动先减小,随后其数值急剧下降,而垂直方向的风载荷波动增大。 相似文献
8.
This paper is concerned with the determination of dynamic load variations in the riser and yoke pivot components of an offshore vessel/mooring oil production and storage system.Forces on the yoke system arise from wave induced inertial and drag forces including current and motion due to vessel surge, heave and pitch.The analysis is carried out in the frequency domain and the results yield the limiting wave height for a specific design of SALS which will give rise to loss of tension in the riser. Also presented are the maximum horizontal and vertical components of load variation at the yoke pivoted connections with the vessel. 相似文献
9.
Flapping wings located beneath or to the side of the hull of the ship are investigated as unsteady thrusters, augmenting ship propulsion in waves. The main arrangement consists of horizontal wing(s) in vertical oscillatory motion which is induced by ship heave and pitch, while rotation about the wing pivot axis is actively controlled. In this work we investigate the energy extraction by the system operating in irregular wave conditions and its performance concerning direct conversion to propulsive thrust. More specifically, we consider operation of the flapping foil in waves characterised by a spectrum, corresponding to specific sea state, taking into account the coupling between the hull and the flapping foil dynamics. The effect of the wavy free surface is accounted for through the satisfaction of the corresponding boundary conditions and the consideration of the wave velocity on the formation of the incident flow. Numerical results concerning thrust and power coefficients are presented, indicating that significant thrust can be produced under general operating conditions. The present work can be exploited for the design and optimum control of such systems extracting energy from sea waves for augmenting marine propulsion in rough seas, with simultaneous reduction of ship responses offering also dynamic stabilisation. 相似文献
10.
This paper investigates the performance of a small axisymmetric buoy under wave-by-wave near optimal control in surge, heave, and pitch modes in long-crested irregular waves. Wave prediction is obtained using a deterministic propagation model. The paper describes the overall formulation leading up to the derivation of the feedforward control forces in surge and heave, and the control moment in pitch. The radiation coupling between surge and pitch modes is accounted for in the model. Actuation is relative to deeply submerged reaction masses. Heave oscillations are constrained by the swept-volume limit. Oscillation constraints are also applied on the surge and pitch oscillations. The paper discusses time-domain simulations for an irregular wave input with and without the present control. Also discussed are results obtained over a range of irregular wave conditions derived for energy periods from 7 s to 17 s, and a significant wave height of 1 m. It is found that, while the gains in power capture enabled by the present control are significant, the actuation forces are also very large, given the small size of the buoy. Further, due to the small size, heave is found to be the dominant contributor to power capture, with relatively modest contributions from surge and pitch. 相似文献
11.
The present paper describes an investigation on the relevance of parametric resonance for a typical fishing vessel in head seas. Results for different Froude numbers are discussed based on experimental, numerical and analytical studies.The first region of resonance is investigated. Distinct wave amplitudes are considered. Some intense resonances are found to occur. The paper compares the experimental results with non-linear time simulations of the roll motion. Very good agreement is found, even when large motions take place.Finally, in order to analyze the experimental/numerical results, analytic consideration is given to distinct parameters affecting the dynamic process of roll amplification. The influence of heave, pitch, wave passage effect, speed and roll restoring characteristics are discussed. 相似文献
12.
首先介绍全球海域圆筒形装置的工程应用案例,对比圆筒形FPSO相对常规船形的优势,然后以原油储量、工艺模块甲板面积、耐波性、稳性、系泊系统、排水量等控制参数为目标,研究圆筒形FPSO主尺度选取依据,分舱原则。重点研究圆筒形装置的阻尼板结构,此为抑制运动响应的关键结构,通过模型试验方法分析对比了水平阻尼板、不同角度锥形阻尼板的特性。最后研究圆筒形装置运动性能分析方法,介绍二阶响应数值预报方法,研究垂荡和横摇运动的耦合效应,分析波频和低频运动响应,通过模型试验进行了验证,从而指导圆筒形装置设计。 相似文献
13.
基于Newton法优化ARMA模型参数的船舶升沉运动预测研究 总被引：1，自引：1，他引：0
为解决波浪补偿系统中时延现象导致的控制性能下降问题,通过建立Newton-ARMA模型提前预测船舶升沉运动来消除时延现象。首先设计卡尔曼滤波器对船舶升沉运动加速度信号进行降噪滤波处理;然后使用加速度二次积分模块将加速度信号转换为位移信号;最后建立自回归滑动平均(ARMA)模型,并使用牛顿(Newton)法对模型参数进行优化,得到船舶升沉运动的Newton-ARMA预测模型。仿真结果表明,Newton-ARMA模型对船舶升沉运动的预测时间可达10 s,预测误差随着预测时间的增加而增大; Newton-ARMA模型对二级海况、三级海况和四级海况下的船舶升沉运动平均预测精度分别达到89.43%、88.53%以及87.78%,远高于ARMA模型对船舶升沉运动预测的精度,说明采用Newton法优化ARMA模型参数可以显著提高船舶升沉运动的预测精度,也即Newton-ARMA模型对控制波浪补偿系统时延具有较好的补偿效果。 相似文献
14.
A time-independent finite-difference method and a fifth-order Runge–Kutta–Felhberg scheme were used to analyze the dynamic responses of sea-wave-induced fully non-linear sloshing fluid in a floating tank. The interaction effect between the fully non-linear sloshing fluid and the floating tank associated with coupled surge, heave and pitch motions of the tank are analyzed for the first time in the present pilot study. For the analysis of fluid motion in the tank, the coordinate system is moving (translating and rotating) with tank motion. The time-dependent water surface of the sloshing fluid is transformed to a horizontal plane and the flow field is mapped on to a rectangular region. The Euler equations as well as the fully non-linear kinematic free surface condition were used in the analysis of the sloshing fluid. The strip theory for linearized harmonic sea-wave loading was adopted to evaluate the regular encounter wave force. In addition, the dynamic coefficients used in the dynamic equations of tank motion were also derived based on strip theory and a harmonic motion of the tank. The characteristics of free and forced tank motions with and without the sloshing effect are studied. By the damping effect, the response of free oscillation will damp out and that of forced oscillation will approach a steady state. Without sea-wave action, the contribution of the sloshing load would enlarge the angular response of tank motion as well as the rise of free surface and the sloshing effect will delay the damping effect on angular displacement. On the contrary, under sea-wave action, the sloshing effect will decrease the dynamic response of tank motion and rise of free surface. The interaction, sloshing and coupling effects are found to be significant and should be considered in the analysis and design of floating tanks. 相似文献
15.
Mooring tension and motion characteristics of a submerged fish reef with net in waves and currents using numerical analysis 总被引：2，自引：0，他引：2
A numerical model was used to analyze the motion response and mooring tension of a submerged fish reef system. The system included a net attached to a rigid structure suspended up from the bottom with a single, high tension mooring by fixed flotation. The analysis was performed by using a Morison equation type finite element model configured with truss elements. Input forcing parameters into the model consisted of both regular and irregular waves, with and without a steady current. Heave, surge and pitch dynamic calculations of the reef structure were made. Tension response results of the attached mooring line were also computed. Results were analyzed in both the time and frequency domain in which appropriate, linear transfer functions were calculated. The influence of the current was more evident in the tension and heave motion response data. This is most likely the result of the large buoyancy characteristics of the reef structure and the length of the mooring cable. Maximum mooring component tension was found to be 13.9 kN and occurred when the reef was subjected to irregular waves with a co-linear current of 1.0 m/s velocity. The results also showed that the system had little damping (in heave) with damped natural periods of 2.8 s. This combination of system characteristics promotes a possible resonating situation in typical open sea conditions with similar wave periods. 相似文献
16.
《Ocean Engineering》2007,34(14-15):1909-1917
Low frequent motions of vessel may cause motion sickness in rough seas. These undesirable effects induce fatigue of crews during the navigation. The motion sickness is always an important criterion for the high-speed craft design. Modern ferry designs have been marketed with a great emphasis on the seakeeping performance. This research has been carried out by investigating the results on the vertical motion sickness incidence (MSI) study for a 40 m wave-piecing catamaran at seas. The primary purpose of this research is to investigate the vertical motion sickness characteristics of a high-speed catamaran ferry. Two mathematical models, three-dimensional translating–pulsating source distribution technique and three-dimensional pulsating source distribution technique, are used for predicting the vertical acceleration responses of the wave-piecing catamaran in oblique waves. The comparison between numerical predictions and experimental data shows a good agreement except that around the pitch resonance region in FP vertical acceleration motions. Based on the experimental observation, the discrepancies may be caused by the nonlinear effects of centre bow during large pitch motions in waves. The comfort assessments are based on the ISO-2631/1997 standard with the hydrodynamic analysis for determining the acceleration levels in different locations on the vessel. The effects of seating location, wave heading and duration of motion exposure on seasickness are discussed. 相似文献
17.
In this paper, a wave generating approach for long-crest irregular waves in a numerical tank by our in-house solver naoe-FOAM-SJTU is presented. The naoe-FOAM-SJTU solver is developed using an open source tool kit, OpenFOAM. Reynolds-averaged Navier?Stokes (RANS) equations are chosen as governing equations and the volume of fluid (VOF) is employed to capture the two phases interface. Incoming wave group is generated by imposing the boundary conditions of the tank inlet. A spectrum based correction procedure is developed to make the measured spectrum approaching to the target spectrum. This procedure can automatically adjust the wave generation signal based on the measured wave elevation by wave height probe in numerical wave tank. After 3 to 4 iterations, the measured spectrum agrees well with the target one. In order to validate this method, several wave spectra are chosen and validated in the numerical wave tank, with comparison between the final measured and target spectra. In order to investigate a practical situation, a modified Wigley hull is placed in the wave tank with incoming irregular waves. The wave-induced heave and pitch motions are treated by Fourier analysis to obtain motion responses, showing good agreements with the measurements. 相似文献
18.
In this paper, a wave generating approach for long-crest irregular waves in a numerical tank by our in-house solver naoe-FOAM-SJTU is presented. The naoe-FOAM-SJTU solver is developed using an open source tool kit, OpenFOAM. Reynolds-averaged Navier-Stokes (RANS) equations are chosen as governing equations and the volume of fluid (VOF) is employed to capture the two phases interface. Incoming wave group is generated by imposing the boundary conditions of the tank inlet. A spectrum based correction procedure is developed to make the measured spectrum approaching to the target spectrum. This procedure can automatically adjust the wave generation signal based on the measured wave elevation by wave height probe in numerical wave tank. After 3 to 4 iterations, the measured spectrum agrees well with the target one. In order to validate this method, several wave spectra are chosen and validated in the numerical wave tank, with comparison between the final measured and target spectra. In order to investigate a practical situation, a modified Wigley hull is placed in the wave tank with incoming irregular waves. The wave-induced heave and pitch motions are treated by Fourier analysis to obtain motion responses, showing good agreements with the measurements. 相似文献
19.
王欣欣 M. Robinson SWIFT Tobias DEWHURST Igor TSUKROV Barbaros CELIKKOL Carter NEWELL 《海洋工程》2015,29(3):431-444
To investigate the dynamics of submersible mussel rafts, the finite element program Aqua-FE?, developed by the University of New Hampshire (UNH), was applied to rafts moored at the surface and submerged. The submerged configuration is used to reduce wave forcing and to avoid contact with floating ice during winters in northern waters. Each raft consists of three pontoons connected by a grid framework. Rafts are intended to support densely spaced mussel ropes hung from the framework. When submerged, the pontoons are flooded, and the raft is held vertically by floats attached by lines. The computer models were developed in Aqua-FE? to simulate the effects of waves and current. They were validated by comparison with wave tank results by use of a 1/10 scale raft physical model. Comparisons showed good agreement for the important heave (vertical) and pitch (rotational) motions, though there was a tendency towards conservative results for wave and current drag. Full-scale simulations of surface and submerged single raft and two rafts connected in tandem were performed. Submerged raft wave response was found to be reduced relative to that at the surface for both the single and two-raft configurations. In particular, the vertical motion of mussel rope connection points was significantly reduced by submergence, resulting in reduced potential for mussel drop-off. For example, the maximum vertical velocities of mussel rope attachment points in the submerged two raft case were 7%?20% of the corresponding velocities when at the surface. 相似文献
20.
参考英国的Kincardine风机采用的新式的Semi-Spar概念,结合spar式基础和半潜式基础的特点,提出了一种新式海上浮式风机平台模型,并基于三维势流理论,利用AQWA软件进行水动力计算,验证新式平台可靠性。分析了在风、浪、流荷载联合作用下,锚链竖向夹角、系缆数量对风机浮式平台运动性能和系泊张力的影响,对系泊系统进行优化,并验证极端工况下的可靠性。结果证明风机平台水平运动和纵摇运动幅值较小,但垂荡幅值略大,而通过减小锚链竖向夹角可以控制平台运动响应幅值,增加系缆数量可以同时减小系泊张力大小。计算结果证明了新型Semi-Spar式海上风机平台可行性,为浮式风机平台及系泊系统的设计提供参考。 相似文献