共查询到20条相似文献，搜索用时 36 毫秒
1.
In this paper, the hydrodynamic efficiency of a floating breakwater system is experimentally studied by use of physical models. Regular waves with wide ranges of wave heights and periods are tested. The efficiency of the breakwater is presented as a function of the wave transmission, reflection, and energy dissipation coefficients. Different parameters affecting the breakwater efficiency are investigated, e.g. the number of the under connected vertical plates, the length of the mooring wire, and the wave length. It is found that, the transmission coefficient kt decreases with the increase of the relative breakwater width B/L, the number of plates n and the relative wire length l/h, while the reflection coefficient kr takes the opposite trend. Therefore, it is possible to achieve kt values smaller than 0.25 and kr values larger than 0.80 when B/L is larger than 0.25 for the case of l/h-1.5 and n=4. In addition, empirical equations used for estimating the transmission and reflection coefficients are developed by using the dimensionless analysis, regression analysis and measured data and verified by different theoretical and experimental results. 相似文献
2.
O.S. Rageh 《Ocean Engineering》2009,36(14):1112-1118
The efficiency of the breakwater, which consists of caissons supported on two or three rows of piles, was studied using physical models. The efficiency of the breakwater is presented as a function of the transmission, reflection and the wave energy dissipation coefficients. Regular waves with wide ranges of wave heights and periods and constant water depth were used. Different characteristics of the caisson structure and the supporting pile system were also tested. It was found that, the transmission coefficient (kt) decreases with increasing the relative breakwater draft D/L, increasing the relative breakwater width B/h, and decreasing the piles gap-diameter ratio G/d. It is possible to achieve kt values less than 0.25 when D/L≥0.1. The reflection coefficient takes the opposite trend especially when D/L≤0.15. The proposed breakwater dissipates about 10-25% of the incident wave energy. Also, simple empirical equations are developed for estimating the wave transmission and reflection. In addition, the proposed breakwater model is efficient compared with other floating breakwaters. 相似文献
3.
4.
5.
Mooring forces in horizontal interlaced moored floating pipe breakwater with three layers 总被引：2，自引：0，他引：2
The paper presents the results from model scale experiments on the study of forces in the moorings of horizontally interlaced, multi-layered, moored floating pipe breakwaters. The studies are conducted with breakwater models having three layers subjected to waves of steepness Hi/L (Hi is the incident wave height and L the wavelength) varying from 0.0066 to 0.0464, relative width W/L (W is the width of breakwater) varying from 0.4 to 2.65, and relative spacing S/D (S is the spacing of pipes and D the diameter of pipe) of 2 and 4. The variation of measured normalized mooring forces on the seaward side and leeward side are analyzed by plotting non-dimensional graphs depicting f/γW2 (f is the force in the mooring per unit length of the breakwater, γ the weight density of sea water) as a function W/L for various values of Hi/d (d is the depth of water). It is found that the force in the seaward side mooring increases with an increase in Hi/L for d/W values ranging between 0.081 and 0.276. The experimental results also reveal that the forces in the seaward side mooring decrease as W/L increases, up to a value of W/L=1.3, and then increases with an increase in W/L. It is also observed that the wave attenuation characteristics of breakwater model with relative spacing of 4 is better than that of the model with relative spacing of 2. The maximum force in the seaward side mooring for model with S/D=4 is lower compared to that for the breakwater model with S/D=2. A multivariate non-linear regression analysis has been carried out for the data on mooring forces for the seaside and leeside. 相似文献
6.
The wave transmission, reflection and energy dissipation characteristics of ‘’-type breakwaters were studied using physical models. Regular and random waves in a wide range of wave heights and periods and a constant water depth were used. Five different depths of immersion (two emerged, one surface flushing and two submerged conditions) of this breakwater were selected. The coefficient of transmission, Kt, and coefficient of reflection, Kr, were obtained from the measurements, and the coefficient of energy loss, Kl was calculated using the law of balance of energy. It was found that the wave transmission is significantly reduced with increased relative water depth, d/L, whether the vertical barrier of the breakwater is surface piercing or submerged, where ‘d’ is the water depth and ‘L’ is the wave length. The wave reflection decreases and energy loss increases with increased wave steepness, especially when the top tip of the vertical barrier of this breakwater is kept at still water level (SWL). For any incident wave climate (moderate or storm waves), the wave transmission consistently decreases and the reflection increases with increased relative depth of immersion, Δ/d from −0.142 to 0.142. Kt values less than 0.3 can be easily obtained for the case of Δ/d=+0.071 and 0.142, where Δ is the height of exposure (+ve) or depth of immersion (−ve) of the top tip of the vertical barrier. This breakwater is capable of dissipating wave energy to an extent of 50–80%. The overall performance of this breakwater was found to be better in the random wave fields than in the regular waves. A comparison of the hydrodynamic performance of ‘’-type and ‘T’-type shows that ‘T’-type breakwater is better than ‘’-type by about 20–30% under identical conditions. 相似文献
7.
Wave interaction with T-type breakwaters 总被引：1，自引：0，他引：1
The wave transmission, reflection and energy dissipation characteristics of partially submerged ‘T'-type breakwaters (Fig. 1) were studied using physical models. Regular and random waves, with wide ranges of wave heights and periods and a constant water depth were used. Five different depths of immersions of the ‘T'-type breakwater were selected. The coefficient of transmission, Kt, coefficient reflection, Kr, were obtained from the measurements and the coefficient of energy loss, Kl is calculated using the law of conservation of energy. It is found that the coefficient of transmission generally reduces with increased wave steepness and increased relative water depth, d/L. This breakwater is found to be effective closer to deep-water conditions. Kt values less than 0.35 is obtained for both normal and high input wave energy levels, when the horizontal barrier of the T type breakwater is immersed to about 7% of the water depth. This breakwater is also found to be very efficient in dissipating the incident wave energy to an extent of about 65% (i.e. Kl>0.8), especially for high input wave energy levels. The wave climate in front of the breakwater is also measured and studied.
Fig. 1. Schematic view of the T-type breakwater. 相似文献
| Full-size image (12K) |
8.
Prediction of scour depth at breakwaters due to non-breaking waves using machine learning approaches
Coastal structures may cease to function properly due to seabed scouring. Hence, prediction of the maximum scour depth is of great importance for the protection of these structures. Since scour is the result of a complicated interaction between structure, sediment, and incoming waves, empirical equations are not as accurate as machine learning schemes, which are being widely employed for the coastal engineering modeling. In this paper, which can be regarded as an extension of Pourzangbar et al. (2016), two soft computing methods, a support vector regression (SVR), and a model tree algorithm (M5′), have been implemented to predict the maximum scour depth due to non-breaking waves. The models predict the relative scour depth (Smax/H0) on the basis of the following variables: relative water depth at the toe of the breakwater (htoe/L0), Shields parameter (θ), non-breaking wave steepness (H0/L0), and reflection coefficient (Cr). 95 laboratory data points, extracted from dedicated experimental studies, have been used for developing the models, whose performances have been assessed on the basis of statistical parameters. The results suggest that all of the developed models predict the maximum scour depth with high precision, the M5′ model performed marginally better than the SVR model and also allowed to define a set of transparent and physically sound relationships. Such relationships, which are in good agreement with the existing empirical findings, show that the relative scour depth is mainly affected by wave reflection. 相似文献
9.
This study investigates the applicability of neural networks to predict whether impact wave force will act on the upright section of a composite breakwater. We employ a three-layered neural network whose units of input layer are h/L, H/h, d/h and BM/h (h: the total water depth; L: the wavelength; H: the wave height; d: the water depth above the mound; BM: the horizontal distance from the shoulder of mound to the caisson). Teach signals are 0.99 and 0.01 according to the cases of occurrence and absence of impact wave force, respectively. The neural network whose parameters are determined through self-learning can accurately predict whether impact wave force occurs. 相似文献
10.
The wave transmission characteristics and wave induced pressures on twin plate breakwater are investigated experimentally in regular and random waves.A total of twenty pressure transducers are fixed on four surfaces of twin plate to measure the wave induced dynamic pressures.The spatial distribution of dynamic wave pressure is given along the surface of the twin plate.The uplift wave force obtained by integrating the hydrodynamic pressure along the structure is presented.Discussed are the influence of different incident wave parameters including the relative plate width B /L,relative wave height /i H a and relative submergence depth s /a on the non-dimensional dynamic wave pressures and total wave forces.From the investigation,it is found that the optimum transmission coefficient,t K occurs around B /L 0.41 ~ 0.43,and the twin plate breakwater is more effective in different water depths.The maximum of pressure ratio decreases from 1.8 to 1.1 when the relative submergence depth of top plate is increased from 0.8to +0.8. 相似文献
11.
The method of empirical orthogonal function (EOF) or principal component analysis (PCA) was used to investigate the spatial and temporal variability of shoreline data sets from Duck, North Carolina, the Gold Coast, Australia, and the United States Pacific Northwest. In the present work, an attempt is made to relate the individual modes of shoreline variability identified by the EOF analyses to select parameterizations of the nearshore environment. The parameters considered include the wave energy (E), the cross-shore and longshore wave energy fluxes (Fx and Fy), the wave steepness (Ho/Lo), the non-dimensional fall velocity parameter (Ω), the profile parameter (P), the surf-similarity parameter (ζ), and a surfzone Froude number (Fr). Correlation analyses were used to evaluate the linear relationship between each of these parameters and the temporal eigenfunctions, ck(t), associated with individual modes of shoreline change. Typically, strong correlations were observed between longshore uniform modes and the monthly means of several of the nearshore parameters. 相似文献
12.
Numerical prediction of performance of submerged breakwaters 总被引：1，自引：0，他引：1
The results of a numerical model study on the transmission characteristics of a submerged breakwater are presented. Study aimed to determine the effect of depth of submergence, crest width, initial wave conditions and material properties on the transmission characteristics of the submerged breakwater. The results highlight the optimum crest width of the breakwater and optimum clear spacing between two breakwaters. A submerged permeable breakwater with ds/d=0.5, p=0.3 and f=1.0, reduces the transmission coefficient by about 10% than the impermeable breakwater. The results indicates an optimum width ratio of B/d=0.75 for achieving minimum transmission. By restricting the effective width ratio of the series of breakwaters to 0.75, studies were conducted to determine the effect of clear spacing between breakwaters on transmission coefficient, suggesting an optimum clear spacing of w/b=2.00 to obtain Kt below 0.6. 相似文献
13.
Simple prediction methods are proposed to estimate the wave induced pressures on smooth impermeable seawalls. Based on the physics of the wave structure interaction, the sloped seawall is divided into a total of five zones (zones 1, 2 and 3 during run-up (corresponding pressures are called as positive pressures) and zones 4 and 5 during run-down (corresponding pressures are called negative pressures)) (Fig. 1). Zone 1 (0<z<d−Hi/2), where the wave pressure is governed by the partial reflection and phase shift; Zone 2 (d−Hi/2<z<d), where the effect of wave breaking and turbulence is significant; Zone 3 (d<z<Run-up height), where the pressure is induced by the run-up water; Zone 4 (Run-down<z<d), where the wave pressure is caused by the run-down effect and Zone 5 (0<z<d-Run down), where the negative wave pressures are due to partial reflection and phase shift effects. Here d is the water depth at the toe of the seawall, Hi is the incident wave height and z is the vertical elevation with toe of the seawall as origin and z is positive upward. For wave pressure prediction in zones 1 and 5, the empirical formula proposed by Ahrens et al. (1993) to estimate the wave reflection and Sutherland and Donoghue's recommendations (1998) for the estimation of phase shift of the waves caused by the sloped structures are used. Multiple regression analysis is carried out on the measured pressure data and empirical formulas are proposed for zones 2, 3 and 4. The recommendations of Van der Meer and Breteler (1990) and Schüttrumpf et al. (1994) for the prediction of wave run-down are used for pressure prediction at zone 4. Comparison of the proposed prediction formulas with the experimental results reveal that the prediction methods are good enough for practical purposes. The present study also shows a strong relation between wave reflection, wave run-up, wave run-down and phase shift of waves on wave pressures on the seawalls. 相似文献
14.
The hydrodynamic performance of vertical and sloped plane, dentated and serrated seawalls were investigated using physical model studies. Regular and random waves of wide range of heights and periods were used. Tests were carried out for different inclinations of the seawall (i.e. θ=30, 40, 50, 60 and 90°) and for a constant water depth of 0.7 m. The wave reflection was measured to assess the dissipation character of the seawalls. It was observed that the serrated seawall was superior to the plane and dentated seawall in reducing the wave reflection. Even for the vertical case, the coefficient of reflection due to regular waves for dentated seawall ranged from 0.6–0.99 and for the vertical serrated seawall it was 0.45–0.98, whereas for the vertical plane wall, it was almost 1.0. It was found that the characteristic dimension of the seawall (i.e. L/W) and the relative water depth (i.e. d/L) were better influencing parameters compared to the conventionally used surf similarity parameter ‘ξ’ (ξ=tan θ/(Hi/L)0.5) in predicting the reflection from the dentated and serrated seawall, where L is the local wave length, W the width of the dent along the length of the seawall slope, d the water depth at the toe and Hi is the incident wave height. A similar trend was observed for the random waves too. The reduction in the wave reflection due to random waves for the dentated seawall as compared to the plane seawall was about 18% and for the serrated seawall, it was 20%. It was observed that the reflection due to random waves was lesser for all the three different walls than the regular waves, due to the mutual interaction of random waves. Multiple regression analysis on the measured data points was carried out and predictive equations for the reflection coefficient were obtained for both regular and random waves. This study will be useful in the design of energy dissipating type vertical quay walls in ports and harbours, sloped seawalls for shore protection from erosion and sloped caisson as breakwaters. Comparison of predictive formulae with the experimental results revealed that the prediction methods were good enough for practical purposes. 相似文献
15.
The stability of the antifer units used on breakwaters in case of irregular placement 总被引：1，自引：0，他引：1
The primary aim of the study is to experimentally investigate the stability performance of antifer units on the trunk section of breakwaters under the effect of regular and irregular waves in case of irregular placement. The stability performance tests were conducted for different slopes, i.e. cot α=1.25, 1.5, 2.0, 2.5, under irregular waves and for cot α=2.5 under regular waves. Hudson’s formula was employed in order to characterize the stability performance of antifer units for the irregular placement technique. Different representative wave height parameters, i.e. Hs, H1/10 and Hmax, were examined to determine the one best characterizing breakwater stability. Furthermore, the effects of wave period and wave steepness on the stability of the breakwater were explored. 相似文献
16.
《Coastal Engineering》1998,35(3):185-209
Two depth inversion algorithms (DIA) applicable to coastal waters are developed, calibrated, and validated based on results of computations of periodic waves shoaling over mild slopes, in a two-dimensional numerical wave tank based on fully nonlinear potential flow (FNPF) theory. In actual field situations, these algorithms would be used to predict the cross-shore depth variation h based on sets of values of wave celerity c and length L, and either wave height H or left–right asymmetry s2/s1, simultaneously measured at a number of locations in the direction of wave propagation, e.g., using video or radar remote sensing techniques. In these DIAs, an empirical relationship, calibrated for a series of computations in the numerical wave tank, is used to express c as a function of relative depth koh and deep water steepness koHo. To carry out depth inversion, wave period is first predicted as the mean of observed L/c values, and Ho is then predicted, either based on observed H or s2/s1 values. The celerity relationship is finally inverted to predict depth h. The algorithms are validated by applying them to results of computations for cases with more complex bottom topography and different incident waves than in the original calibration computations. In all cases, root-mean-square (rms)-errors for the depth predictions are found to be less than a few percent, whereas depth predictions based on the linear dispersion relationship—which is still the basis for many state-of-the-art DIAs—have rms-errors 5 to 10 times larger. 相似文献
17.
Dulce María Pérez-Romero Miguel Ortega-Sánchez Antonio Moñino Miguel A. Losada 《Coastal Engineering》2009
This work presents a simple method to evaluate the performance of a porous breakwater when it is impinged with normal incidence by a non-breaking monochromatic wave train. It is based on: 1) a potential flow model for wave interaction with permeable structures and 2) a set of experimental tests on a rectangular porous structure with uniform granular distribution. A characteristic friction diagram is obtained considering wave energy balance in a control volume, minimising the error between the numerical model and the experimental results for the wave transmission coefficient. Results show that, for large breakwater widths, the reflection process reaches a saturation regime before the waves exit the structure at a distance from the seaside between the interval 0.2 < x/L < 0.45. For larger breakwater widths, the reflection coefficient is almost constant (except for “resonant” conditions) and wave transmission decreases exponentially. Under such conditions, the wave propagation through the porous medium depends on the relative diameter D/L and the porosity of the material; the dependence on the relative breakwater width B/L and the ratio diameter wave height D/H is weak. This diagram intends to be useful for preliminary engineering studies of breakwater's efficiency and performance and as an adequate selection criteria of the experimental stone diameter to minimize scale effects in laboratory studies. 相似文献
18.
斜向波浪作用下双层水平板式防波堤波浪荷载试验研究 总被引：1，自引：0，他引：1
In this study, systematic physical model tests were performed to investigate the wave forces on the twin-plate breakwater under irregular waves. Based on the experimental results, the effects of the relative plate width B/L,wave height Hs/D and incident angle θ0 on the wave forces were analyzed and discussed. The results showed that:(1) The envelopes of the total wave pressure were generally symmetrical along the direction of plate width under the incident angles(θ0) being 0°, 15°, 30°, 45° and 60°. In particular, the envelopes of wave pressure atθ0=30° were larger than all other cases.(2) The synchronous pressure distribution of the breakwater under oblique wave action was more complicated comparing to the normal incident waves.(3) Based on data analysis, an empirical formula was obtained to estimate the total vertical force of the twin-plate breakwater.This empirical formula can be a good reference for the design basis of engineering applications under specified wave conditions. 相似文献
19.
The wave transmission, reflection, and energy dissipation of the double rows of vertical piles suspending horizontal steel C shaped bars are experimentally and theoretically studied under normal regular waves. Different wave and structural parameters are investigated e.g. the wave length, the C shaped bars draft and spacing, the supporting piles diameter and spacing, and the space between the double rows. Also, the theoretical model based on an eigenfunction expansion method is developed to study the hydrodynamic breakwater performance. In order to examine the validity of the theoretical model, the theoretical results are compared with the experimental and theoretical results obtained by different authors. Comparison between experiments and predictions showed that theoretical model provides a good estimate to the different hydrodynamic coefficients when the friction factors of the upper and the lower parts are fU = 1.5 and fL = 0.75. The present breakwater physical model gives efficiency near other similar systems of different shapes. 相似文献