首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到18条相似文献,搜索用时 156 毫秒
1.
随着全站仪测角测距精度的提高,在高程联测中,用EDM高程导线测量代替三四等水准测量,成为外业高程测量的重要方法之一。分析了影响EDM高程导线测量精度的因素,讨论了提高EDM高程导线测量精度的办法,提出了效率函数的概念,并以某测区三级GPS大地控制网高程联测数据为例,从精度和效率方面进行了计算对比分析。  相似文献   

2.
城市与工程测量EDM导线技术标准的分析   总被引:1,自引:0,他引:1  
基于导线测量误差理论与电磁测距(EDM)导线的特性,分析讨论了城市与工程测量EDM导线的各项技术参数,提出了各级EDM导线技术标准的建议,通过计算验证所给出的这些技术指标是合理可靠的。  相似文献   

3.
论低等级光电测距导线的技术标准   总被引:1,自引:1,他引:0  
焦明连 《海洋测绘》2005,25(4):32-34
针对《城镇地籍调查规程》和《城市测量规范》对光电测距(EDM)导线技术参数规定的不同,对低等光电测距导线的合理等级及各等级导线的技术标准进行了研究,并通过精度估算证明了各级导线精度的可靠性。  相似文献   

4.
本文介绍了平潭海峡采用了较先进的测距三角高程法和计算理论。完成距离长达3478m跨海三等水准测量。通过改造观测觇板、提高照准精度、运用两个大地四边形的布网形式,构成一个以跨海测线为主的具有外部检核条件的水准闭合环;通过间接测量仪器高、间接计算高差、间接求两差改正数的方法,取得了远距离跨海水准测量的一些成功经验。  相似文献   

5.
许时耕 《海洋学报》1984,6(3):368-376
高程异常和垂线偏差是大地测量及空间技术中常用到的一组大地参数.精确计算大洋区这些参数的工作是十分困难的.本文以我国在中太平洋调查的一个海区为例,介绍了用重力法计算洋区高程异常及垂线偏差的基本公式、分区原则、资料来源、数据处理及程序设计等主要内容.讨论了计算误差的主要来源及提高计算精度的基本途径,分析了试算区大地水准面参数的展布特征.  相似文献   

6.
针对现场环境限制导致双目摄像机无法按照标准模式安装的问题,对影响匹配效果的因素进行了研究,得出了基于高程差的重叠度和匹配率的计算公式与变化趋势,并通过实验进行验证。结果表明,实验结论与分析相符,并且从实验中可得,在满足双目测距匹配率的要求下,可找到高程差极值,并据此指导现场安装。  相似文献   

7.
邢喆  奚歌  樊妙  李鹏  李四海 《海洋通报》2013,32(1):8-11
针对现有海陆高程信息的统一管理需求,论述了航空LIDAR资料和海底地形资料的处理流程,研究了现有主要垂直参考面之间的转换关系,提出了海陆地形转换模型构建的方法.以上海市海岸带为示例,实现了海陆高程/深度数据的无缝拼接.构建了区域海陆一体DEM模型.  相似文献   

8.
本文应用河道固定断面高程数据和卫星遥感资料,建立了一种基于曲线正交网格的河道数字高程模型(DEM),进而进行河道冲淤定量计算的普适方法。应用1991—2012年黄河孙口-艾山河段河道断面高程数据,结合卫星遥感资料,分别应用本文方法、断面法和基于矩形网格的网格地形法计算了孙口-艾山河段的冲淤演化,比较了不同方法的差异,探讨了不同方法产生误差的主要原因,结果表明:基于三种方法计算得出的研究区河道冲淤演化趋势基本一致,但冲淤量差异较大。断面法计算结果与本文方法结果较为接近,平均相对误差约为9%,其计算误差主要源于未考虑河道宽度变化和断面方位与河道夹角的变化。基于矩形网格建模计算结果与本文方法结果相差较大,平均相对误差可达40%以上,主要由于现有断面数据空间分布不均匀,导致计算网格对于弯曲河道的控制不足,进而导致河道高程插值失真。本文方法考虑了河道河势与河长变化,计算网格与河道边界拟合较好,优化了河道高程插值方法,降低了断面方位对插值结果的影响,能够准确的计算河道的冲淤通量。  相似文献   

9.
大气垂直折光是影响三角高程测量精度的主要因素,视线距离地面较高时,在有利观测时段进行垂直角观测(中午),并用传统的方法进行数据处理可有效减弱大气折光影响。而在沙漠戈壁滩等干旱环境下这两种条件难于实现。从数据处理的角度,结合某测区高程导线的观测数据探讨了减弱折光影响的一种改进的平差模型,与传统方法相比能取得较好效果。  相似文献   

10.
研究了在海底声速梯度为正的情况下,应答器最大互测距距离的计算方法。对于平坦地形,直接基于声线跟踪的原理计算;对于倾斜地形,首先将实际声线轨迹近似为圆弧,然后利用牛顿法迭代计算初始掠射角,进一步得到两应答器间的水平距离。仿真实验结果表明,应答器的架设高度越高,最大互测距距离越远;同样架设高度,坡度越大的地形互测距距离越短。  相似文献   

11.
A traversing system to measure bottom boundary layer hydraulic properties   总被引:1,自引:0,他引:1  
This study describes a new convenient and robust system developed to measure benthic boundary layer properties, with emphasis placed on the determination of bed shear stress and roughness height distribution within estuarine systems by using velocity measurements. This system consisted of a remotely operated motorised traverser that allowed a single ADV to collect data between 0 and 1 m above the bed. As a case study, we applied the proposed traversing system to investigate bottom boundary layer (BBL) hydraulic properties within Coombabah Creek, Queensland, Australia. Four commonly-employed techniques: (1) Log-Profile (LP); (2) Reynolds stress (RS); (3) Turbulent Kinetic Energy (TKE); and (4) Inertial Dissipation (ID) used to estimate bed shear stresses from velocity measurements were compared. Bed shear stresses estimated with these four methods agreed reasonably well; of these, the LP method was found to be most useful and reliable. Additionally, the LP method permits the calculation of roughness height, which the other three methods do not. An average value of bed shear stress of 0.46 N/m2, roughness height of 4.3 mm, and drag coefficient of 0.0054 were observed within Coombabah Creek. Results are consistent with that reported for several other silty bed estuaries.  相似文献   

12.

When a subduction-zone earthquake occurs, the tsunami height must be predicted to cope with the damage generated by the tsunami. Therefore, tsunami height prediction methods have been studied using simulation data acquired by large-scale calculations. In this research, we consider the existence of a nonlinear power law relationship between the water pressure gauge data observed by the Dense Oceanfloor Network System for Earthquakes and Tsunamis (DONET) and the coastal tsunami height. Using this relationship, we propose a nonlinear parametric model and conduct a prediction experiment to compare the accuracy of the proposed method with those of previous methods and implement particular improvements to the extrapolation accuracy.

  相似文献   

13.
为了实现长度基线的量值统一,保证长度基线的溯源和量传准确,在分析长度基线校准方式、测量标准的建立、溯源途径和计量保障需求的基础上,采用高精度光电测距仪和GPS接收机建立了长度基线校准装置测量标准,解决了传统基线校准方法难于实现大长度、空中基线的校准问题,提高了长度基线校准精度、效率,降低了生产成本,丰富了长度计量标准器具。  相似文献   

14.
1988-2002年黄海和渤海风浪后报   总被引:2,自引:1,他引:1  
本文对黄海和渤海风浪开展长期后报实验,时间范围覆盖1988至2002年,并分析相应的区域波候特征。首先,模式输出的月平均有效波高和卫星数据比对一致。其次,我们讨论了气候态月平均有效波高和平均波周期的时空分布特征。有效波高和平均波周期的气候态空间分布都呈现出西北-东南、或由近岸向深水区增加的趋势,这种空间的分布特征和局地的风强迫和水深密切相关。同时,海浪参数的季节变化也较显著。进一步,我们统计分析了风场和有效波高的极值,给出并揭示了黄海和渤海多年一遇有效波高的空间结构,并讨论了有效波高极值和风强迫极值之间的联系。  相似文献   

15.
Hydrodynamic modeling of perforated structures   总被引:2,自引:0,他引:2  
A hydrodynamic model of perforated or slotted structures is proposed. It is asymptotic in the sense that the openings are supposed to be infinitely small and numerous, and the wall thickness to be nil. At variance with other work, a quadratic, not linear, law, relating the pressure differential to the traversing velocity, is assumed. As a result the hydrodynamic coefficients (added mass and damping) become amplitude dependent. The model is applied to bodies of various shapes including cylinders, plates and disks, in forced motion or submitted to incoming waves. Good agreement with experimental data is generally observed.  相似文献   

16.
台湾岛邻近海域台风浪的模拟研究   总被引:8,自引:0,他引:8  
基于目前国际上较为先进的第三代近岸海浪数值模式SWAN(Simulation Waves Near-shore)。在充分考虑相关物理过程(风生浪,底摩擦,白帽耗散,深度诱导波破碎,非线性波-波相互作用)基础上,以较高的分辨率对影响台湾岛邻近海域的9015号台风浪过程进行了模拟研究。模式所需风场由藤田台风风场模型同化相应台风资料后提供;用自嵌套方式提供模式波谱边界条件。模拟结果与实际台风浪资料相符较好。台风过程模拟结果表明;台风中心位于台湾岛邻近海域的不同位置,台风浪有效波高的分布特征和传播方向都有着较大的差异。可以为整个台湾岛邻近海域台风浪分布特征的了解与认识提供较好的参考。  相似文献   

17.
广东阳西近岸海域波浪的分布特征   总被引:2,自引:0,他引:2  
通过对广东阳西近岸测站1a实测波浪资料及岸边同期风资料的整理与分析,探讨了该海域的波浪特性,得出研究海域不分方向H1/10年平均值为1.00 m,常浪向为SE向,出现的频率为38.35%,强浪向为SE向,观测期间的最大波高出现在0814号"黑格比"台风期间,Hmax值为8.31 m.用已有的理论分布函数对实测统计数据进行拟合,筛选出研究海域的波高分布、周期分布及波高与周期联合分布的特征,结果表明双参数威布尔理论波高分布、杨正己威布尔周期分布、朗格-赫金斯83模式或者孙孚模式较为适用于本海区的波高分布、周期分布、波高周期联合分布;结合相应的风速风向资料,运用回归分析方法,建立了该地区的波高与风速之间、波高与波周期之间的关系.  相似文献   

18.
In high-resolution, shallow-water seismic surveys, correction for water-column height variations caused by tides, weather, and currents is an important part of data processing. In this study, we present a very simple method of correction for profile-length (i.e., long-wavelength) water-column height variations for high-resolution seismic data using a reference bathymetric grid. First, the difference between the depth of the seafloor picked from seismic data and the bathymetry from the bathymetric grid is computed at the locations where the shot points of seismic profiles and the bathymetric grid points are collocated or closest. Then, the results are gridded and smoothed to obtain the profile-length water-column height variations for the survey area. Next, the water-column height variations for each seismic profile are extracted from the smoothed grid and converted to two-way traveltimes. The corrections for the remaining mis-ties at the intersections, computed within a circular region around each tie shot point, are added to the corrections for the water-column height variations. The final, mistie corrected water-column height corrections are loaded to the SEGY trace header of seismic data as a total static. We applied this method to the sparker data acquired from the shallow-water area off the western-central part of Korea where the tidal range is over 7 m. The corrections for water-column height variations range from -10 to 4 m with a median value of about -2 m. Large corrections occur locally between and near the islands probably due to the amplification and shortening in tidal wavelength caused by rapid shoaling toward the islands.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号