首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到19条相似文献,搜索用时 78 毫秒
1.
多波束反向散射强度数据处理研究   总被引:13,自引:5,他引:8  
在探讨多波束测深系统反向散射强度与海底底质类型的关系基础上,研究影响反向散射强度的各种因素,主要分析了海底地形起伏、中央波束区反射信号对反向散射强度的影响,并给出了消除这些影响的方法;将处理后的“纯”反向散射强度数据镶嵌生成海底声像图,为海底底质类型划分以及地貌解译提供了基础数据和辅助判读依据.  相似文献   

2.
最大似然分类法在多波束底质分类中的应用   总被引:1,自引:0,他引:1  
研究利用多波束测深系统获取的反向散射强度数据和海底声像图,通过数据预处理,应用Beyes统计分类方法实现了对海底泥、砂、砾石和基岩等底质类型的自动分类识别。  相似文献   

3.
济州岛南部海域海底声呐图像分析与声学底质分类   总被引:2,自引:2,他引:0  
东海北部外陆架靠近济州岛南部海域,是黄海槽向冲绳海槽延伸的部分,属于黑潮分支黄海暖流的通道入口,分布着脊槽相间的海底底形,对其海底声呐图像的处理分析及声学底质分类的分析研究,有助于了解该通道海底底形表层纹理特征及沉积物分布规律。基于在济州岛南部海域获取的多波束声呐数据,应用图像处理技术和方法,对数据进行了处理,获得了海底声呐影像图,并对其表层纹理特征进行了描述和分析;同时,基于多波束反向散射强度数据,结合19组海底地质取样数据,建立研究区海底反向散射强度与沉积物粒度特征之间的统计关系模型,并以改进的学习向量量化神经网络方法,实现对海底粉砂质砂、黏土质砂以及砂-粉砂-黏土3种底质类型的快速自动分类识别。  相似文献   

4.
基于改进BP神经网络的海底底质分类   总被引:2,自引:0,他引:2       下载免费PDF全文
通过采用遗传算法优化神经网络初始权值的方法,将GA算法与BP神经网络有机结合,应用于海底底质分类。基于多波束测深系统获取的反向散射强度数据,应用改进的BP神经网络分类方法,实现对海底基岩、砾石、砂、细砂和泥等底质类型的快速、准确识别。通过实验比较,GA-BP神经网络分类精度明显高于BP神经网络,证明了该方法的有效性和可靠性。  相似文献   

5.
在南黄海某一典型的砂质海底区域,采用全向性声源和全向性接收水听器开展了频率范围为6-24 kHz的海底反向声散射测量。测量结果表明,在避免海面散射干扰并满足远场条件的情况下,本次实验获得了掠射角范围为18~80°的海底反向声散射强度,其数值为-41.1~24.4 dB。在有效掠射角范围内,声散射强度总体上随掠射角的增大呈现出增大趋势,但对于不同的频率,其变化趋势有所不同,反映出不同的散射机理。在20°、40°和60°掠射角处,在6-24 kHz的频率范围内反向声散射强度总体上呈现出正相关的频率依赖性,其线性相关斜率分别为0.2229 dB/kHz、0.5130 dB/kHz、0.1746 dB/kHz。在最大掠射角80°处,反向声散射强度未呈现出明显的频率相关性。  相似文献   

6.
杨彬  何林帮 《海洋学报》2018,40(7):143-149
多波束反向散射强度数据应用广泛,但由于受到角度响应的影响,导致生成的多波束声呐图像质量偏低,且现有角度响应改正方法在复杂海底底质环境下适应性较差。为此本文对散射强度进行分析,给出了两种多波束反向散射强度数据归一化方法,分别为基于高斯拟合以及角度响应的散射强度改正方法,前者主要是基于散射强度的变化规律进行改正,而后者则是基于声波的散射机理进行改正。实验结果表明两种方法较传统改正方法精度均有约30%的提升,并且角度响应方法较高斯拟合方法改正精度更高,但计算效率有所下降。以上实验验证了两种方法的有效性,实现了散射强度数据的归一化,提升了多波束声呐图像的质量。  相似文献   

7.
针对利用侧扫声纳检测海底管道时因其检测声影图像模糊而导致管道悬空高度检测误差过大的问题,提出了侧扫声纳声波掠射角优化设计的思路及方法。阐述了利用侧扫声纳对海底管道进行检测的工作原理,并利用海底管道和海底底质反向散射强度的计算公式探讨了声波在海底的反向散射强度、侧扫声纳声影图像的质量以及声波掠射角的取值这三者之间的关系对海底管道悬空高度h计算精度的影响,从理论上确定声波掠射角最佳取值范围的存在。通过工程实例的现场检测与比对试验,获得了在本试验所处海域环境中利用侧扫声纳检测海底管道时声波掠射角的最佳取值范围,对于类似的海底管道检测工程具有一定的指导意义。  相似文献   

8.
北黄海海底麻坑群形态的定量研究及控制因素   总被引:1,自引:0,他引:1  
本文基于高分辨率多波束水深数据和反向散射强度数据,对北黄海海底麻坑群的形态参数进行定量研究,结合水深、地形坡度和后向散射强度的变化准确界定了麻坑的轮廓,识别出圆形、椭圆形、拉长型麻坑共282个,并在ArcGIS软件中对其形态参数进行了分析计算,麻坑的平均长轴1.36 km,短轴0.78 km,直径0.94 km,面积0.88 km2,平均周长3.82 km,长宽比1.83,深度0.3~2.5 m,平均面积密集度13%,麻坑的剖面形态有麻坑边缘凹陷、中部有明显凸起(W1型),麻坑边缘凹陷、中部略凸起(W2型),麻坑中部单纯凹陷(V型),分别集中分布在麻坑群的北部、南部、西部。麻坑的平面规模大、深度小的原因与地层中形成麻坑的游离气体浓度较小有关,也可能受到了地震、海啸等外力的诱发。麻坑的长轴优势走向为ENE-WSW、NNE-SSW,底流对其形状的塑造起了较大作用,部分麻坑成串排列,形成串珠状的麻坑链,其排列方式受到海底古河道、古潟湖等沉积地层结构的控制。海底麻坑群发育区反向散射强度为-60~-71 dB,麻坑内部较麻坑外部平均高5 dB,可能为麻坑内部气体泄漏引起海底沉积物被剥蚀后残留下的粗颗粒物质或海底生物活动留下的遗迹导致的。  相似文献   

9.
探测海底天气渗漏活动形成的甲烷羽状流,研究其基本特征和分布,具有重要的资源和环境效益。目前对于海底甲烷羽状流的声学探测主要以船载单波束和分裂波束声呐系统为主,而多波束声呐系统的声学图像分辨率较高,覆盖宽度较大,具有良好的应用前景。对于单个或少量甲烷羽状流气体运移通量的测算,多采用声学原位观测,即通过ROV携带声呐探头或在海底固定安装特定声呐系统的方式实现。对于某一海域海底天然气渗漏总量的测算,多采用走航式声学遥感观测,其核心是建立由甲烷羽状流体积反向散射强度反演其气体运移通量的模型。  相似文献   

10.
介绍几种典型的海底底质分类技术   总被引:2,自引:0,他引:2  
本文主要介绍了四家海洋仪器公司的最新海底底质分类技术。它们分别利用多波束的反向散射强度数据、单波束的回声波形结构数据和旁侧声纳数据。采用了多参数统计分析、波形结构分析和影像属性分析等方法,实现了快速、高效、大面积地对海底底质进行间接的分类。尽管它们的技术各不相同,但都可以分为监督分类方式和非监督分类方式。  相似文献   

11.
Processing Multibeam Backscatter Data   总被引:1,自引:0,他引:1  
A new highly precise source of data has recently become available using multibeam sonar systems in hydrography. Multibeam sonar systems can provide hydrographic quality depth data as well as high-resolution seafloor sonar images. We utilize the seafloor backscatter strength data of each beam from multibeam sonar and the automatic classification technology so that we can get the seafloor type identification maps. In this article, analyzing all kinds of error effects in backscatter strength, data are based on the relationship between backscatter strength and seafloor types. We emphasize particularly analyzing the influences of local bottom slope and near nadir reflection in backscatter strength data. We also give the correction algorithms and results of these two influent factors. After processing the raw backscatter strength data and correcting error effects, we can get processed backscatter strength data which reflect the features of seafloor types only. Applying the processed backscatter strength data and mosaicked seafloor sonar images, we engage in seafloor classification and geomorphy interpretation in future research.  相似文献   

12.
A new highly precise source of data has recently become available using multibeam sonar systems in hydrography. Multibeam sonar systems can provide hydrographic quality depth data as well as high-resolution seafloor sonar images. We utilize the seafloor backscatter strength data of each beam from multibeam sonar and the automatic classification technology so that we can get the seafloor type identification maps. In this article, analyzing all kinds of error effects in backscatter strength, data are based on the relationship between backscatter strength and seafloor types. We emphasize particularly analyzing the influences of local bottom slope and near nadir reflection in backscatter strength data. We also give the correction algorithms and results of these two influent factors. After processing the raw backscatter strength data and correcting error effects, we can get processed backscatter strength data which reflect the features of seafloor types only. Applying the processed backscatter strength data and mosaicked seafloor sonar images, we engage in seafloor classification and geomorphy interpretation in future research.  相似文献   

13.
侧扫声纳图像增强技术   总被引:1,自引:0,他引:1  
随着海洋探测技术的飞速发展,侧扫声纳的图像质量和定位精度迅速提高,其应用日益广泛和深入。在声纳图像判读分析时,常常需要进行辐射改正和均衡增强。根据海底地貌声纳图像的特点,归纳了几种有效、适用的图像增强方法,并建立了声纳图像分析软件。  相似文献   

14.
高质量的海底声强图是进行多波束海底底质分类、目标识别的基础。要得到"单纯"反映海底底质信息的声强图,就需要对原始声强数据进行地形改正,消除地形因素的影响。在描述了多波束数据中水深数据不能满足声强数据的改正要求问题的基础上,提出了以水深数据覆盖范围为约束的声强数据选取方法。实例计算结果表明:该方法在能有效地选取高质量的声强数据,提高了基于声强图像的海底底质分类精度。  相似文献   

15.
The relative height of the seafloor can be estimated by using two vertically displaced receivers. In this paper, we propose techniques to improve the accuracy of the estimated height. Our results are based on the use of synthetic aperture sonar (SAS) imaging, which implies coherent addition of complex images acquired from a moving platform. The SAS processing improves the along-track (or azimuth) resolution, as well as the signal-to-noise ratio (SNR), which in turn improves the estimated height accuracy. We show that the shift of the effective center frequency induced by coherent, frequency-dependent scattering affect the time-delay estimates from complex cross correlations, and we propose a correction technique for broadband signals with uneven magnitude spectra. To reduce the effect of geometrical decorrelation and increase the coherence between the images, we beamform the sonar images onto an a priori estimate of the seafloor height before correlating. We develop a mathematical model for the imaging geometry. Finally, we demonstrate our proposed estimators by providing relative seafloor height estimates from real aperture and SAS images, obtained during the InSAS-2000 experiment at Elba Island in Italy. In particular, we demonstrate that the SAS image quality is significantly improved by inclusion of the height estimates as a priori information.  相似文献   

16.
In this paper we examine the use of bathymetric sidescan sonar for automatic classification of seabed sediments. Bathymetric sidescan sonar, here implemented through a small receiver array, retains the advantage of sidescan in speed through illuminating large swaths, but also enables the data gathered to be located spatially. The spatial location allows the image intensity to be corrected for depth and insonification angle, thus improving the use of the sonar for identifying changes in seafloor sediment. In this paper we investigate automatic tools for seabed recognition, using wavelets to analyse the image of Hopvågen Bay in Norway. We use the back-propagation elimination algorithm to determine the most significant wavelet features for discrimination. We show that the features selected present good agreement with the grab sample results in the survey under study and can be used in a classifier to discriminate between different seabed sediments.  相似文献   

17.
Simrad EM多波束声纳系统回波强度数据的分析与应用   总被引:1,自引:0,他引:1  
首先分析了Simrad EM多渡束声纳系统回渡强度数据获取时系统进行的增益处理,分别探讨了深度数据包和海底图像数据包中回波强度数据的表征内容及意义,研究了不同数据包中回波强度数据的记录方式、特点及应用范围,为多波束水下目标识别和海底底质分类研究提供准确、表述清晰的基础数据.  相似文献   

18.
Deep towed side-scan sonar vehicles such as TOBI acquire high quality imagery of the seafloor with very high spatial resolution but poor locational accuracy. Fusion of the side-scan sonar data with bathymetry data from an independent source is often desirable to reduce ambiguity in geological interpretations, to aid in slant-range correction and to enhance seafloor representation. The main obstacle to fusion is accurate registration of the two datasets.The application of hierarchical chamfer matching to the registration of TOBI side-scan sonar images and multi-beam swath bathymetry is described. This matches low level features such as edges in the TOBI image, with corresponding features in a synthetic TOBI image created by simulating the flight of the TOBI vehicle through the bathymetry. The method is completely automatic, relatively fast and robust, and much easier than manual registration. It allows accurate positioning of the TOBI vehicle, enhancing its usefulness as a research tool. The method is illustrated by automatic registration of TOBI and multi-beam bathymetry data from the Mid-Atlantic Ridge.  相似文献   

19.
Acoustic backscatter images of the seafloor obtained with sidescan sonar systems are displayed most often using a flat bottom assumption. Whenever this assumption is not valid, pixels are mapped incorrectly in the image frame, yielding distorted representations of the seafloor. Here, such distortions are corrected by using an appropriate representation of the relief, as measured by the sonar that collected the acoustic backscatter information. In addition, all spatial filtering operations required in the pixel relocation process take the sonar geometry into account. Examples of the process are provided by data collected in the Northeastern Pacific over Fieberling Guyot with the SeaMARC II bathymetric sidescan sonar system and the Sea Beam multibeam echo-sounder. The nearly complete (90%) Sea Beam bathymetry coverage of the Guyot serves as a reference to quantify the distortions found in the backscatter images and to evaluate the accuracy of the corrections performed with SeaMARC II bathymetry. As a byproduct, the processed SeaMARC II bathymetry and the Sea Beam bathymetry adapted to the SeaMARC II sonar geometry exhibit a 35m mean-square difference over the entire area surveyed.On leave at the Naval Research Laboratory, Code 7420, Washington D.C. 20375-5350.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号