共查询到18条相似文献，搜索用时 109 毫秒
1.
为优化径向透平动叶片的结构型式,有效提高透平工作效率,本文基于Ansys-Fluent软件构建振荡水柱波能发电装置径向冲击式透平的三维瞬态全流域数值模型,通过改变透平动叶片吸力面型式,研究了正弦往复入射气流条件下动叶片厚度差异对透平扭矩、压强等参量的影响及其对透平输入系数、扭矩系数和周期平均效率等非定常性能评价参数的影响。在保证压力面型式不变情况下,研究了5种动叶片厚度分别为7 mm、13 mm、16 mm、19 mm和22 mm的透平在呼气、吸气阶段的非定常工作性能,结果表明：不同动叶片厚度的透平的非定常工作性能存在较大差异,动叶片厚度为13 mm的透平非定常工作性能最优,最大峰值效率可达47.7%。 相似文献
2.
径流式空气透平是振荡水柱式波能发电系统的二级能量转换装置,因其具有结构简单、输出扭矩大、轴向推力小的优势,得到了越来越多的关注。采用计算流体力学软件Ansys-Fluent 12.0,通过数值模拟方法考察了不同转子叶片稠度对径流式空气透平定常无量纲评价参数的影响规律。研究结果表明:虽然径流式透平可在双向气流下实现单向旋转,但当气流通过方向不同时,透平的定常工作性能存在明显差异,这与传统轴流式透平完全不同;此外,稠度对透平效率的影响在不同流量系数范围内也不同。因此,综合考虑气流流向、透平整个工作范围内输出效率,推荐采用的转子叶片稠度为2.34。 相似文献
3.
基于计算流体力学软件的三维数值模拟技术,分析了碟形越浪式波能发电装置的越浪性能,通过构建基于水气两相VOF(Volume of Fluid)模型的三维数值波浪水槽对该装置进行三维数值模拟研究,数值计算结果与物理试验结果相互对比验证较为吻合,验证了所构建的三维数值波浪水槽的可靠性,通过考察装置的坡度、导流叶片个数、干舷高度对越浪性能的影响确定装置的最优结构参数。结果表明,在装置的斜坡面边缘增加回流板可减少波浪的反射,提高装置的越浪性能。在数值模拟中将装置的斜坡面边缘处安装回流板对碟形越浪式波能发电装置参数进行优化,通过分析回流板的长度对装置越浪性能的影响来探索最优回流板长度。 相似文献
4.
一种自行研制的新型波浪发电装置—对向流、翼笼式、低参数透平［１］。该透平具有独特的壳体,能使叶轮在对向气流通过时作定向旋转,从而带动发电机发电。实验证明该机运转可靠、效率高,又具有结构简单、易于制造、寿命长、成本低等优点。用于海上浮标灯的波浪发电装置,与发电机匹配好,且容易起动。还阐述了波浪发电装置的效率分析与计算,以及活塞实验研究、水池模拟实验和海上实验结果。 相似文献
5.
当今世界,全球资源严重匮乏,环境日益恶化,波浪能作为一种清洁、可再生海洋能源,有利于贯彻我国可持续发展战略。文中针对南海某海域,根据国家海洋局提供的波浪周期和波高数据,通过计算流体力学(CFD)数值模拟,研究不同时期波浪周期和波高的变化对轴流式水轮机效率的影响。计算结果表明,因波浪参数变化,浮筒式波浪能发电装置水头变化范围为11~17 m,优选设计水头为13 m。通过改变水轮机叶片安装角度,优化水轮机效率,并对水轮机转轮及出水流道流动特性进行研究。最终得出:在优选设计水头为13 m时,水轮机在叶片相对安放角为-4°,最高效率达85.67%,水轮机转轮及出水流道流态平直,水轮机工作性能稳定,满足浮筒式波能发电装置工作要求。文中研究工作,为优化浮筒式波能发电平台及提高平台投资回报率奠定理论基础。 相似文献
6.
针对潮流能双向来流的特点及当前潮流能发电轮机的研究现状和存在的问题,提出了一种新型的双向直驱式发电轮机。叶片基本翼型为S型,并对其进行受力分析,得到相应的计算公式,结合叶片翼型厚度和形状约束,求解出各个截面的形状,并三维建模形成一种新型"S"翼型轮机。轮机两端安装具有防水性能的永磁发电机,外侧增设双向导流罩,构成双向直驱式发电轮机装置模型。在水槽实验中,首先找出不同的模拟流速下获取功率的最佳负载阻值,在此基础上收集了转速及功率数据,绘制尖速比-获能系数关系曲线图和流速—获能系数关系曲线图,可以论证尖速比的取值对获取最佳功率的重要性,同时该翼型轮机具有良好的空载启动性能及双向吸收来流的能力,2 m/s流速下获能效率最大值接近40%。 相似文献
7.
针对浮式消波海流机样机测试时出现的问题,对其吃水深度线和叶片安装角度进行优化。根据装置结构特点,用Gambit建立了装置横截面的二维网格模型。根据浮式消波海流机实际工作环境,利用Fluent流体仿真软件,使用VOF(volume of fluid)两相流模型,分配空气相与液态水相在流域中的不同比例,来确定不同的吃水深度线。并且结合k-epsilon紊流模型建立模拟仿真环境。先对3种水线进行仿真分析,然后进行实验验证。通过分析对比装置的3种不同吃水深度线的模拟与实验结果,得到装置的最优吃水深度线为1/3水线。基于最优吃水深度线,分别对叶片的4种安装角度在相同的仿真环境中进行模拟仿真。利用仿真得到的扭矩数据,计算扭矩系数、功率系数,分析对比仿真数据以及仿真过程中扭矩趋势图得出4种叶片安装角度的最优角度是90°。吃水深度线决定了装置的消波能力,并且为叶片获能提供条件,叶片安装角度直接影响着装置的获能效率,所以最优的吃水深度线和叶片安装角度对海流机的消波能力和获能效率具有重要意义。 相似文献
8.
9.
稳态流动中对称翼透平的空气动力性能 总被引：6，自引：0，他引：6
本文对12个不同设计参数的对称翼型透平模型进行了实验研究,获得了其在0°～90°迎角范围的空气动力特性曲线及效率曲线。根据试验结果,分析了设计参数对透平性能的影响,发现了失速区透平力系数的非单位特性。本文的结果可以供透平设计及改善透平性能时使用,在进行波能系统分析时,也可作为透平的传递函数。 相似文献
10.
潮流能发电装置支撑结构对水轮机水动力学性能影响研究 总被引：1，自引：0，他引：1
水平轴潮流能水轮机在工作过程中,由于支撑结构的存在,会使水轮机周围流场中的潮流流向、流速等参数发生不同程度的改变,进而影响水轮机的性能和发电装置的稳定性。为了研究支撑结构对水轮机水动力学性能的影响规律,以某100 k W单立柱座底式潮流能发电装置的支撑结构为研究对象,采用CFD方法,分别在正、反向来流时采用不同支撑结构的共六种工况下,对潮流能水轮机模型的获能和受力进行数值模拟。通过水槽模型试验,验证数值模拟的可靠性。研究结果表明:支撑结构对水轮机的水动力学性能的影响不容忽视,针对所研究的支撑结构,在正向来流时水轮机的获能系数降幅约30%,轴向力系数降幅约28%;反向来流时的降幅更大,分别约为63%和41%。 相似文献
11.
The performance of a Wells turbine with various non-uniform tip clearances was investigated using computational fluid dynamics (CFD). The investigation was performed on numerical models of a NACA0020 blade profile under steady flow conditions. The performance of turbines with uniform and non-uniform tip clearances was compared. The results were also compared with experimental results in literature. It was shown that the performance of turbine with non-uniform tip clearance is similar with that of turbine with uniform one in terms of torque coefficient, input power coefficient, and efficiency. However, the turbine with non-uniform tip clearance seems to have a preferable overall performance. An investigation on the flow-field around the turbine blade was performed in order to explain the phenomena. 相似文献
12.
13.
Offshore wind energy resources are operational in cold regions, while offshore wind turbines will face the threat of icing. Therefore, it is necessary to study icing of offshore wind turbines under different icing conditions. In this study, icing sensitivity of offshore wind turbine blades are performed using a combination of FLUENT and FENSAP-ICE software, and the effects of liquid water content (LWC), medium volume diameter (MVD), wind speed and air temperature on blade icing shape are analyzed by two types of ice, namely rime ice and glaze ice. The results show that the increase of LWC and MVD will increase the amount of ice that forms on the blade surface for either glaze ice or rime ice, and an increase of MVD will expand the adhesion surface between ice and blade. Before reaching the rated wind speed of 11.4 m/s, it does not directly affect the icing shape. However, after reaching the rated wind speed, the attack angle of the incoming flow decreases obviously, and the amount of ice increases markedly. When the ambient air temperature meets the icing conditions of glaze ice (i.e., −5°C to 0°C), the lower the temperature, the more glaze ice freezes, whereas air temperature has no impact on the icing of rime ice. Compared with onshore wind turbines, offshore wind turbines might face extreme meteorological conditions, and the wind speed has no impact on the amount of ice that forms on the blade surface for most wind speeds
相似文献14.
Impulse turbine, working as a typical self-rectifying turbine, is recently utilized for the oscillating water column (OWC) wave energy converters, which can rotate in the same direction under the bi-directional air flows. A numerical model established in Fluent is validated by the corresponding experimental results. The flow fields, pressure distribution and dimensionless evaluating coefficients can be calculated and analyzed. Effects of the rotor solidity varying with the change of blade number are investigated and the suitable solidity value is recommended for different flow coefficients. 相似文献
15.
水平轴海流能发电机叶片设计与性能分析 总被引：2，自引：1，他引：1
全球海洋蕴藏着丰富的海流能,合理利用海流能可以有效缓解能源危机。以额定工况下获能系数达到最大值为目标,利用叶素-动量理论设计了150 kW水平轴海流能发电机的叶片。使用叶素-动量理论结合普朗特修正和葛劳渥修正的方法,预测了海流机在不同尖速比以及不同桨距角下的水动力性能,分析了攻角和载荷沿着叶片径向的分布规律。使用CFD方法计算了海流机在不同尖速比下的水动力性能,并与理论方法的计算结果进行了比较。理论方法和CFD方法的结果均表明,所设计的海流机最大获能系数位于设计尖速比处,证明基于叶素-动量理论的水平轴海流机叶片设计方法是有效的。 相似文献
16.
The paper presents the effects of blade twist and nacelle shape on the performance of horizontal axis tidal current turbines using both analytical and numerical methods. Firstly, in the hydrodynamic design procedure, the optimal profiles of untwisted and twisted blades and their predicted theoretical turbine performance are obtained using the genetic algorithm method. Although both blade profiles produce desired rated rotational speed, the twisted blade achieves higher power and thrust performance. Secondly, numerical simulation is performed using sliding mesh technique to mimic rotating turbine in ANSYS FLUENT to validate the analytical results. The Reynolds-Averaged Navier-Stokes (RANS) approximation of the turbulence parameters is applied to obtain the flow field around the turbine. It is found that power and axial thrust force from BEMT (Blade Element Momentum Theory) method are under-predicted by 2% and 8% respectively, compared with numerical results. Afterwards, the downstream wake field of the turbine is investigated with two different nacelle shapes. It is found that the rotor performance is not significantly affected by the different nacelle shapes. However, the structural turbulence caused by the conventional nacelle is stronger than that by the NACA-profiled shape, and the former can cause detrimental effect on the performance of the downstream turbines in tidal farms. 相似文献
17.
《中国海洋工程》2021,(3)
Three blade-geometry optimization models derived along with assumptions from the blade element momentum(BEM) approach are studied by using a steady BEM code to improve a small horizontal-axis rotor of three blades that has been previously used in experiments. The base rotor blade has linear-radially varying chord length and pitch angle, while the other three models noted as Burton, Implicit and Hansen due to their references and characteristics yield blades of non-linearly varying chord length and pitch angle. The aim is to compare these rapid models and study how assumptions embedded in them affect performance and induction factors. It is found that the model that has the least assumptions(Hansen) and which considers the blade-profile drag in its optimization procedure yields the highest power coefficient, C_P, at the optimal tip speed ratio(TSR), about 7% higher than the base one and also higher C_P at high TSR. It produces an axial induction factor distribution along the blade that is closest to the 1 D optimal value of 1/3. All optimized tangential induction-factor distributions along the blade closely vary as inverse to the square of the radial distance, while being mildly higher than the base distribution. It shows that sufficient swirl is necessary to increase power but at a level causing not too much energy loss in unnecessary swirl of the wake. At high TSR, all optimized rotors adversely produce higher thrust than the base one, but the one with most embedded assumptions(Burton) produces the highest thrust. Details of all three optimization models are given along with the distributions of the power, thrust, blade hydrodynamic efficiency and induction factors. 相似文献
18.
实密度是影响轮机获能特性的关键因素之一。文中以卧式轮机实密度为基变量,以其获能系数为主要考察点,对3种实密度卧式轮机进行水槽实验方案设计和水动力性能研究。实验分别对水流流速、轮机旋转角速度、主轴转矩以及功率进行测量,并对其对主轴的扭矩、轮机的获能系数以及叶片的旋转特性进行定量分析,最终证实了该卧式轮机的单一运行特性。通过绘制基于实密度的轮机转矩—转角曲线、获能系数—尖速比曲线和轮机功率—尖速比曲线,阐明了实密度影响卧式轮机获能水动力性能的规律,即其获能系数和发电功率都随着工况速比呈先增后降趋势。实密度较低轮机因浪流流失而获得能量小,但实密度过高轮机会导致叶片间湍流涌动,加速叶片失速特性而影响轮机获能。这为卧式浪流轮机结构优化提供了可靠依据和借鉴。 相似文献