首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到17条相似文献,搜索用时 109 毫秒
1.
Hybrid-driven underwater glider is a new type of unmanned underwater vehicle, which combines the advantages of autonomous underwater vehicles and traditional underwater gliders. The autonomous underwater vehicles have good maneuverability and can travel with a high speed, while the traditional underwater gliders are highlighted by low power consumption, long voyage, long endurance and good stealth characteristics. The hybrid-driven underwater gliders can realize variable motion profiles by their own buoyancy-driven and propeller propulsion systems. Stability of the mechanical system determines the performance of the system. In this paper, the Petrel-Ⅱ hybrid-driven underwater glider developed by Tianjin University is selected as the research object and the stability of hybrid-driven underwater glider unitedly controlled by buoyancy and propeller has been targeted and evidenced. The dimensionless equations of the hybrid-driven underwater glider are obtained when the propeller is working. Then, the steady speed and steady glide path angle under steady-state motion have also been achieved. The steady-state operating conditions can be calculated when the hybrid-driven underwater glider reaches the desired steady-state motion. And the steady-state operating conditions are relatively conservative at the lower bound of the velocity range compared with the range of the velocity derived from the method of the composite Lyapunov function. By calculating the hydrodynamic coefficients of the Petrel-Ⅱ hybrid-driven underwater glider, the simulation analysis has been conducted. In addition, the results of the field trials conducted in the South China Sea and the Danjiangkou Reservoir of China have been presented to illustrate the validity of the analysis and simulation, and to show the feasibility of the method of the composite Lyapunov function which verifies the stability of the Petrel-Ⅱ hybrid-driven underwater glider.  相似文献   

2.
Profiles observed by Sea-Wing underwater gliders are widely applied in scientific research. However, the quality control(QC) of these data has received little attention. The mismatch between the temperature probe and conductivity cell response times generates erroneous salinities, especially across a strong thermocline. A sensor drift may occur owing to biofouling and biocide leakage into the conductivity cell when a glider has operated for several months. It is therefore critical to design a mature real-time QC procedure and develop a toolbox for the QC of Sea-Wing glider data. On the basis of temperature and salinity profiles observed by several Sea-Wing gliders each installed with a Sea-Bird Glider Payload CTD sensor, a real-time QC method including a thermal lag correction, Argo-equivalent real-time QC tests, and a simple post-processing procedure is proposed. The method can also be adopted for Petrel gliders.  相似文献   

3.
PETREL,a winged hybrid-driven underwater glider is a novel and practical marine survey platform which combines the features of legacy underwater glider and conventional AUV (autonomous underwater vehicle).It can be treated as a multi-rigid-body system with a floating base and a particular hydrodynamic profile.In this paper,theorems on linear and angular momentum are used to establish the dynamic equations of motion of each rigid body and the effect of translational and rotational motion of internal masses on the attitude control are taken into consideration.In addition,due to the unique external shape with fixed wings and deflectable rudders and the dual-drive operation in thrust and glide modes,the approaches of building dynamic model of conventional AUV and hydrodynamic model of submarine are introduced,and the tailored dynamic equations of the hybrid glider are formulated.Moreover,the behaviors of motion in glide and thrust operation are analyzed based on the simulation and the feasibility of the dynamic model is validated by data from lake field trials.  相似文献   

4.
A hybrid underwater glider Petrel-II has been developed and field tested. It is equipped with an active buoyancy unit and a compact propeller unit. Its working modes have been expanded to buoyancy driven gliding and propeller driven level-flight, which can make the glider work in strong currents, as well as many other complicated ocean environments. Its maximal gliding speed reaches 1 knot and the propelling speed is up to 3 knots. In this paper, a 3D dynamic model of Petrel-II is derived using linear momentum and angular momentum equations. According to the dynamic model, the spiral motion in the underwater space is simulated for the gliding mode. Similarly the cycle motion on water surface and the depth-keeping motion underwater are simulated for the level-flight mode. These simulations are important to the performance analysis and parameter optimization for the Petrel-II underwater glider. The simulation results show a good agreement with field trials.  相似文献   

5.
Combining high precision numerical analysis methods with optimization algorithms to make a systematic exploration of a design space has become an important topic in the modern design methods. During the design process of an underwater glider''s flying-wing structure, a surrogate model is introduced to decrease the computation time for a high precision analysis. By these means, the contradiction between precision and efficiency is solved effectively. Based on the parametric geometry modeling, mesh generation and computational fluid dynamics analysis, a surrogate model is constructed by adopting the design of experiment (DOE) theory to solve the multi-objects design optimization problem of the underwater glider. The procedure of a surrogate model construction is presented, and the Gaussian kernel function is specifically discussed. The Particle Swarm Optimization (PSO) algorithm is applied to hydrodynamic design optimization. The hydrodynamic performance of the optimized flying-wing structure underwater glider increases by 9.1%.  相似文献   

6.
We present a study of the nonlinear coupling internal resonance for the heave roll and pitch performance of a spar platform under the wave and vortex-induced loads when the ratio of the frequencies of heave, roll and pitch are approximately 2:1:1. In consideration of varying wet surface, the three DOFs nonlinear coupled equations are established for the spar platform under the effect of the first-order wave loads in the heave and pitch, and vortex-induced loads in the roll. By utilizing the method of multi-scales when the vortex-induced frequency is close to the natural roll frequency, the first-order perturbation solution is obtained analytically and further validated by the numerical integration. Sensitivity analysis is performed to understand the influence of the damping and the internal detuning parameter. Two cases with internal resonance are shown. The first case is that no saturation phenomenon exists under small vortex-induced loads. The first order perturbation solution illustrates that only the vortex-induced frequency motion in roll and the super-harmonic frequency motion in heave are excited. The second case is that the vortex-induced loads are large enough to excite the pitch and a saturation phenomenon in the heave mode follows. The results show that there is no steady response occurrence for some cases. For these cases chaos occurs and large amplitudes response can be induced by the vortex-induced excitation.  相似文献   

7.
This article studies the application of the alternating current field measurement (ACFM) method in defect detection for underwater structures. Numerical model of the ACFM system is built for structure surface defect detection in seawater environment. Finite element simulation is performed to investigate rules and characteristics of the electromagnetic signal distribution in the defected area. In respect of the simulation results, underwater artificial crack detection experiments are designed and conducted for the ACFM system. The experiment results show that the ACFM system can detect cracks in underwater structures and the detection accuracy is higher than 85%. This can meet the engineering requirement of underwater structure defect detection. The results in this article can be applied to establish technical foundation for the optimization and development of ACFM based underwater structure defects detection system.  相似文献   

8.
Depth-trim mapping control of underwater vehicle with fins   总被引:1,自引:1,他引:0  
Underwater vehicle plays an important role in ocean engineering.Depth control by fin is one of the difficulties for underwater vehicle in motion control.Depth control is indirect due to the freedom coupling between trim and axial motion.It includes the method of dynamic analysis and lift-resistance-coefficient experiment and theory algorithm.By considering the current speed and depth deviation,comprehensive interpretation is used in object-planning instruction.Expected depth is transformed into expected trim.Dynamic output fluctuation can be avoided,which is caused by linear mapping of deviation.It is steady and accurate for the motion of controlled underwater vehicles.The feasibility and efficiency of the control method are testified in the pool and natural area for experiments.  相似文献   

9.
Ince-Strutt stability chart of ship parametric roll resonance in irregular waves is conducted and utilized for the exploration of the parametric roll resonance in irregular waves. Ship parametric roll resonance will lead to large amplitude roll motion and even wreck. Firstly, the equation describing the parametric roll resonance in irregular waves is derived according to Grim’s effective theory and the corresponding Ince-Strutt stability charts are obtained. Secondly, the differences of stability charts for the parametric roll resonance in irregular and regular waves are compared. Thirdly, wave phases and peak periods are taken into consideration to obtain a more realistic sea condition. The influence of random wave phases should be taken into consideration when the analyzed points are located near the instability boundary. Stability charts for different wave peak periods are various. Stability charts are helpful for the parameter determination in design stage to better adapt to sailing condition. Last, ship variables are analyzed according to stability charts by a statistical approach. The increase of the metacentric height will help improve ship stability.  相似文献   

10.
In the 21st century,people have come to the era of ocean science and ocean economy.With the development of ocean science and technology and the thorough research on the ocean,underwater mating technique has been widely used in such fields as sunk ship salvage,deep ocean workstation,submarine lifesaving aid and military affairs.In this paper,researches are made home and abroad on mating technology.Two-joint mating system of underwater vehicle is designed including plane system,three-dimensional assembly system and control system in order to increase the capacity of adapting platform obliquity and adopting rotational skirt scheme.It is clear that the system fits the working space of underwater vehicle passageway and there is no interference phenomenon in assembly design.The finite element model of the system shell and the pressurization of the joint are established.The results of the finite element computing and the pressing test are accordant,and thus it can testify that the shell material meet the need of intension and joint pressurization is reliable.Modeling of the control system is accomplished,and simulation and analysis are made,which can provide directions for the controller design of mating system of underwater vehicles.  相似文献   

11.
水下滑翔机器人运动分析与载体设计   总被引:4,自引:0,他引:4  
水下滑翔机器人是一种新型水下机器人,具有噪声低、航行距离远、续航时间长、成本低等特点。分析了水下滑翔机器人的驱动机理和运动实现,给出了水下滑翔机器人典型运动的仿真结果,并以正在设计的一水下滑翔机试验样机为研究对象,描述了样机的整体结构布局,详细研究了浮力调节机构、俯仰调节机构和横滚调节机构的实现方法,并就样机中各执行机构的设计实现进行了论述。  相似文献   

12.
水下滑翔机器人系统研究   总被引:12,自引:2,他引:10  
水下滑翔机器人是一种新型的水下机器人,可以作为水下监测平台用于大范围、长时间的大尺度海洋环境监测作业。文中调查了水下滑翔机器人的国内外发展现状,分析了其可能的应用领域。详细介绍了中国科学院沈阳自动化研究所开发的水下滑翔机器人系统,包括载体外形优化设计、载体结构设计和控制系统设计。分析了水下滑翔机器人定常滑翔运动和空间螺旋会转运动的运动性能。  相似文献   

13.
For Cconsideration ofing both the eccentric rotatable rigid body and the translational rigid body, the dynamic model of the underwater glider is derived. Dynamical behaviors are also studied based on the model and can be used as the guidance to underwater gliders design. Gibbs function of the underwater glider system is derived first, and then the nonlinear dynamic model is obtained by use of Apell Equations. The relationships between dynamical behaviors and design parameters are studied by solving the dynamic model. The spiral motion, swerving motion in three dimensions and the saw-tooth motion of the underwater glider in vertical plane are studied. Lake trials are carried out to validate the dynamic model.  相似文献   

14.
水下滑翔机器人运动机理仿真与实验   总被引:1,自引:0,他引:1  
对水下滑翔机器人SEA-WING的定常滑翔运动和空间定常螺旋回转运动进行机理分析,针对其特定水动力系数进行仿真,得出其运动机理特性.在此基础上,通过湖试实验数据对仿真结果进行验证,认为对于定常滑翔运动,以约36°航迹角滑行可得到最大水平速度;在相同航迹角航行情况下,水平方向速度随净浮力的增大而增大.对于定常回转运动,回转半径由载体的质量、俯仰角、水动力参数、横滚角确定.在质量和俯仰角保持不变条件下,横滚角对回转半径的影响较明显,系统的回转半径可以通过控制横滚角来实现的.  相似文献   

15.
水下滑翔机是开展海洋无人移动观测的重要平台,其实际航行轨迹往往与预设路径存在较大差异,多台水下滑翔机协同观测时,难以始终保持预设的组网阵列。本研究提出一种基于牛顿力学积分的水下滑翔机群协同控制算法,根据水下滑翔机群出、入水的异步性调节水下滑翔机入水前的运动参数。基于对水下滑翔机受力分析,利用牛顿力学积分还原水下滑翔机在海洋中的运动状态,进而运用水下滑翔机群的协同控制算法同时约束多台水下滑翔机的运动,并开展仿真实验。实验结果证明该算法能够使多台水下滑翔机较好地保持预设组网阵列,从而可对目标海域进行协同观测。  相似文献   

16.
温差能驱动的水下滑翔器设计与实验研究   总被引:11,自引:1,他引:10  
论文设计开发了一种新型的温差能驱动的水下滑翔器,并对它做了水域实验研究。文章讨论了温差能驱动的滑翔器运动机理及其在垂直剖面的运动分析,得到稳态运动的参数解。结合能够把水域温差能转变为机械能的热机设计以及滑翔器的主要机械结构和控制硬件系统设计,完成了滑翔器的初步设计与开发。滑翔器在千岛湖进行了水域实验,实验结果表明,此水下滑翔器完全能够利用温差能实现预定的滑翔运动。  相似文献   

17.
水下滑翔器的运动建模与分析   总被引:7,自引:2,他引:5  
介绍了水下滑翔器的工作机理,对其沉浮阶段的滑翔过程进行了动力学分析,推导了滑翔器在垂直剖面上的动力学方程。论文深入分析了水下滑翔器稳态时的运动规律,以水下滑翔器试验模型为例,推导了其稳态运动参数,通过线性化与适当的简化,得到模型在垂直剖面上的运动状态方程,讨论了系统的可控性与可观测性,为水下滑翔器系统的开发设计和控制提供了理论依据,具有重要的指导意义。  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号