共查询到19条相似文献，搜索用时 93 毫秒
1.
2.
面对日益增长的海洋资源勘探需求,海洋资源四维勘探拖缆阵列的研究越来越被人们所重视。作为拖缆动态控制策略研究的前提与依据,拖缆阵列的动力学特性始终是该领域在技术突破进程中的重要课题。以Ablow的经典模型为基础,采用微元法对拖缆阵列建立三维模型,并在时域上采用广义α算法对非线性方程进行离散求解,通过程序编译,对拖缆在四种工况(即拖船匀速直线航行、回转航行、变速直线航行以及拖点处存在升沉运动等)下的响应进行计算分析,着重考量其深度及张力的变化。仿真计算结果表明,广义α算法对拖缆阵列姿态在空间和时间上离散求解,算法稳定性良好,弥补了传统有限差分法对于时域不稳定的缺陷。 相似文献
3.
深拖系统为达到预定的工作深度,必须有一根足够长的拖缆支持其工作。为保证所选拖缆具有一定的经济性和可靠性,在深拖系统设计的初步阶段能通过理论分析获得各拖缆要素对深拖系统运动的影响将具有重大意义。故本文从理论研究的角度,详细考察了缆重、缆阻力系数等系统要素对深拖系统运动的影响。这一研究可以为深拖系统设计时选择合适的缆提供重要依据 相似文献
4.
为了解复杂海况下风浪对水下拖缆的影响进行了动力学仿真研究。以P-M谱作为海浪谱密度公式,计算一组不同频率的组成波,采用线性波浪叠加法,计算由波浪引起的空间流场速度及加速度,推导叠加波的干扰力,将不规则波引入水下拖缆动力学模型中,采用四阶龙格库塔积分法对动力学模型进行数值求解,讨论拖缆在不同海况下的动力特性。结果表明,随着海况等级的提高,叠加波的频率范围逐渐降低,拖缆的垂向偏移量以及拖点处张力均会产生明显增加及波动,且其波动周期接近叠加波的平均周期;在不同浪向角的作用下,拖缆波动规律与规则波作用下类似,但也具有一些不规则波的特点。 相似文献
5.
海洋可控源电磁拖曳系统是海洋可控源电磁勘探系统的重要组成部分,对光电复合缆和绞车的强度有着较高的要求。为了保障作业安全,避免拖缆崩断、绞车损坏等事故的发生,需要对拖曳系统所受的张力进行评估,为实际作业提供参考。本文采用拖曳系统稳态运动求解方法,模拟拖体在海水中的位置,以及放缆时绞车所受的牵引张力,模拟结果与海试实测数据能够较好地吻合。在拖缆长度一定的情况下,随着拖曳速度的增大,绞车牵引张力先减小再增大,光电复合缆长度越长这种现象越明显。 相似文献
6.
拖曳系统计算中拖缆与拖体的耦合计算 总被引：4，自引：0，他引：4
针对带有水下设备舱的拖曳系统,提出了一种有效的算法,来获得拖曳系统的运行状态。将拖曳系统分成拖缆和水下拖体两个部分,分别建立运动数学模型。拖缆部分的模型以Ablow和Schechter的运动数学模型为基础;拖体部分的模型采用类似潜器的水下六自由度运动方程。将这两部分方程联立,统一求解,解决两个模型之间的耦合问题。经过数值仿真的检验证明算法具有可行性。 相似文献
7.
针对海洋测量水下拖曳设备位置确定问题,综合考虑拖缆受力、海流影响以及水下拖体的运动性质,建立了水下拖曳设备的位置计算模型,并仿真计算分析了测量船在不同航行状态下拖曳设备位置确定的规律,探讨了不同海流效应对拖曳设备位置确定的影响。仿真计算结果表明,在海洋动态环境作用下,拖缆各方向的偏移明显呈曲线形状,非简单几何运算所确定。测船各方向的运动均可对水下拖体的位置在相应方向产生一定影响,而水下拖体位置的变化量小于测船拖点位置的变化量。海流对水下拖曳设备定位可造成数米的偏差,需进行相应改正。建议可考虑采取船载式ADCP实时测流辅助水下拖曳设备定位的工作模式。 相似文献
8.
9.
水下拖缆物理参数不均匀会影响拖缆的动力特性,研究非均匀拖缆的参数变化对拖缆动力特性的影响有一定的工程实际意义。建立了拖曳系统运动的三维数学模型,推导出了水下非均匀拖缆的稳态运动控制方程,在首尾两端加上相应的定解条件,直接求得或使用嵌套二分法求得非均匀拖缆在端点的初始值,进而求解稳态动力学方程。借助文献中的拖缆—海底拖车系统算例,通过计算结果的对比,验证了数学模型及计算方法的正确性。通过四阶龙格库塔法进行数值仿真计算,得到了稳态解,分析了非均匀拖缆自身物理参数变化对缆绳系统稳态运动的影响。结果表明,非均匀拖缆的切向阻力系数、法向阻力系数、直径和密度变化会影响稳态缆形和张力分布,影响的程度各不相同。最后给出了两个尾拖船系统非均匀拖缆的稳态运动算例。 相似文献
10.
11.
主动式声纳列阵拖曳系统姿态数值计算 总被引：2，自引：1，他引：2
主动式声纳列阵拖曳系统是用于探测潜艇的新型声纳系统，为了准确探测潜艇的位置，必须首先预报声纳列阵的瓷态，本文通过对其三维力学模型的分析，得到该系统的运动微分方程，其中缆索的力学方程是基于Ablow和Milinazzo的模型，而对于拖体则运用六自由度空间运动方程模拟，结合边界条件，用有限差分法求解，通过对拖船的不同运动状态如匀速，变速和回转的计算，证明本文的方法对于预报声纳列阵的姿态是有效的。 相似文献
12.
波浪作用下缆船拖带系统非线性运动数值模拟 总被引：1，自引：0，他引：1
基于船舶操纵性运动方程和拖缆的三维动力学运动方程,提出了被拖点位置匹配的方法,建立了拖船—拖缆—被拖船系统整体非线性拖带动力学模型。为了考察被拖船航向稳定性与横向稳性的关系以及波浪载荷作用的影响,被拖船采用水平面四自由度运动方程,并引入了波浪的作用力和力矩。拖船采用PD控制方法较真实地模拟了拖船航向改变的运动过程。对一个拖船—拖缆—被拖船系统(5 000 t的拖船和3 000 t的被拖船)在时域内进行了规则波浪作用下拖带运动的模拟,计算结果表明被拖带船舶在波浪中运动呈现运动稳定、不稳定和临界状态3种可能的特性。根据模拟计算结果,认为波浪中拖带航向稳定是被拖带船舶保持稳性的必要条件。 相似文献
13.
The dynamic response of a towed cable system to ship maneuver is parametrically simulated. Three dimensionless parameters influence on towed cable system maneuverability is investigated. They are ratio of total length to turning radius R/L, ratio of cable mass to vehicle mass σ, and ratio of mass unit length to hydrodynamic force w/r. An oscillatory motion of towed vehicle is found in simulation of spiral towed courses. Features of this oscillation in different spiral courses are compared. The sharp turns, gradual turns and their transient states of towed cable dynamics for different course directions are discussed extensively. According to the characters of transient states and horizontal trajectories evolution of maneuvered cable system, the dynamic behaviors can be divided into three situations in Fig. 8 turning maneuvers. The behavior of towed cable system during a zigzag turning course is simulated in the end. Two ingredients of heave motion are found during small ratio of turning radii to length in this course. The primary damp to initial turning becomes weak and the response to alternative turns plays a more and more important role. The damping properties of the transient behavior in different maneuvers show a periodical invariance to σ during some turning maneuvers. 相似文献
14.
This paper analyses nonlinear dynamics of cable towed body system. The cable has been modeled and analyzed using a new nodal position finite element method, which calculates the position of the cable directly instead of the displacement by the existing finite element method. The newly derived nodal position finite element method eliminates the need of decoupling the rigid body motion from the total motion, where numerical errors arise in the existing nonlinear finite element method, and the limitation of small rotation in each time step in the existing nonlinear finite element method. The towed body is modeled as a rigid body with six degrees of freedom while the tow ship motion is treated as a moving boundary to the system. A special procedure has been developed to couple the cable element with the towed body. The current approach can be used as design tool for achieving improved directional stability, maneuverability, safety and control characteristics with the cable towed body. The analysis results show the elegance and robustness of the proposed approach by comparing with the sea trial data. 相似文献
15.
In this paper,the dynamic response of undersea -+towed systems is numerically simulated.Atwo body towed system is especially considered in detail.The factors influencing the heave oftowed-bodies,such as the weight of the towed-body(in sea water),the length and the weight(in sea water)per unit length of the cable between towed-bodies and towing ship,are investigated in detail.Calculationsshow that the two-body towed system can greatly increases the stability of the towed system. 相似文献
16.
Compensation for source heave by use of a Kalman filter 总被引：2，自引：0，他引：2
This paper presents a procedure for data filtering to compensate for the effects of the towed body dynamics (heave), in shallow marine seismic reflection records. A method to extract an approximate record of the heave contribution to data collected is outlined. The method utilizes the time to water-sediment interface on each acoustic return record to construct the required approximate heave motion record. The frequency response of the heave component record provides the basis for a proposed linear model for the heave motion. A formulation of the heave compensation requirement as a Kalman filtering problem in optimal linear estimation theory is given. A discussion of the computational aspects and practical results are discussed to conclude the paper. 相似文献
17.
D.A. Chapman 《Ocean Engineering》1984,11(1):23-64
The hydrodynamic forces and moments that act on a towed fish are described and related to fundamental static and dynamic towing characteristics. It is shown that, when the fin height is reduced almost to the point giving neutral stability in pitch, the fish maintains almost constant pitch attitude while it is forced to heave or surge by ship motion transmitted down the cable.Wind tunnel tests provide the necessary hydrodynamic data for a computer simulation in two dimensions of the Bath Mk 3 sonar fish towed on faired cable. The results show that the magnitude of the pitch attitude variations of the fish can be greatly reduced by decreasing the fin size, with further reduction being possible by correctly locating the pointwhere the cable is attached to the fish. It is also shown that decreasing the fin size reduces the magnitude of the tension variations in the cable, thereby lowering the probability that the cable will go slack.These results generalise to a large class of towed systems using either or bare cable, and a formula is included by which the magnitude of the ship-inducing pitching motion of a fish can be estimated, given the necessary hydrodynamic data.Possible difficulties associated with towing a low stability fish are considered and a method is included for assessing the minimum stability likely to be necessary to achieved satisfactory towing behaviour. 相似文献
18.
Numerical simulation of undersea cable dynamics 总被引：7，自引：0，他引：7
A fully three-dimensional code has been written to compute the motion of a towed cable. The code is based on a robust and stable finite difference approximation to the differential equations derived from basic dynamics. A 3500-ft (1.07 km) cable pulled at 18.5 knots (34.3 km hr−1) through a circular turn of 700 yd (0.64 km) radius has been computed in about half of the real time of the maneuver. The computed displacements are close to the measured ones; the changes in depth are within 2%. 相似文献
19.
An efficient algorithm is presented which simulates the three-dimensional motion of a towed cable. The formulation is based on an implicit, second-order finite difference approximation of the equations of motion. The results of the computation are compared both to those obtained by another numerical model and to experimental measurements. 相似文献