共查询到20条相似文献，搜索用时 46 毫秒
1.
The pile group with elevated cap is widely used as foundation of offshore structures such as turbines, power transmission towers and bridge piers, and understanding its behavior under cyclic lateral loads induced by waves, tide water and winds, is of great importance to designing. A large-scale model test on 3×3 pile group with elevated cap subjected to cyclic lateral loads was performed in saturated silts. The preparation and implementation of the test is presented. Steel pipes with the outer diameter of 114 mm, thickness of 4.5 mm, and length of 6 m were employed as model piles. The pile group was cyclic loaded in a multi-stage sequence with the lateral displacement controlled. In addition, a single pile test was also conducted at the same site for comparison. The displacement of the pile cap, the internal forces of individual piles, and the horizontal stiffness of the pile group are presented and discussed in detail. The results indicate that the lateral cyclic loads have a greater impact on pile group than that on a single pile, and give rise to the significant plastic strain in the soil around piles. The lateral loads carried by each row of piles within the group would be redistributed with loading cycles. The lateral stiffness of the pile group decreases gradually with cycles and broadly presents three different degradation patterns in the test. Significant axial forces were measured out in some piles within the group, owing to the strong restraint provided by the cap, and finally lead to a large settlement of the pile group. These findings can be referred for foundation designing of offshore structures. 相似文献
2.
An experimental investigation was made into the response of piles in sand subjected to lateral cyclic loading. Seven instrumented model piles tests were conducted. Five tests were conducted under typical magnitude and number of cyclic loading, and two were under static loading. The results were used to deduce modulus of subgrade reaction k and the profile of limiting lateral resistance force per unit length (LFP, pu profile) in light of closed-form solutions. The study demonstrates a large impact of lateral (cyclic) load level than the number of cycles, a 1.5–2.8 times increase in the modulus k, and a 10% reduction in the pu due to cyclic loading. The tests confirm the linear correlation between maximum bending moment and the applied lateral load, regardless of the number of cycles. 相似文献
3.
采用有限元软件ABAQUS建立了海上风电单桩基础与土相互作用数值计算模型,将波浪、洋流及风荷载等效成双向对称循环荷载,研究了水平循环荷载作用下不同因素对桩身水平位移、剪力和弯矩的影响规律。研究表明,随着循环荷载比的增加,桩身位移零点和桩身剪力反弯点沿埋深逐渐下移,桩身弯矩最大值点位于浅层土体;不同荷载频率时桩身位移在零点以上变化较大,桩身弯矩随着频率的增加逐渐增大;单向循环荷载作用下桩身位移最大,双向对称循环荷载作用下桩身位移最小;壁厚较小时对桩身水平位移影响较大;在位移零点之上范围内可以考虑设计"上厚下薄"的钢管桩,以减小桩身水平位移;不同桩壁厚时桩身剪力曲线在埋深约6D处出现交点,且泥面处桩身弯矩变化不明显。 相似文献
4.
In offshore engineering, pile foundations are commonly constructed in marine deposits to support various structures such as offshore platforms. These piles are subjected to lateral cyclic loading due to wind, wave action, and drag load from ships. In this paper, centrifuge model tests are conducted to investigate the response of the existing single piles due to lateral cyclic loading. The cyclic loading was simulated by a hydraulic actuator. It is found that the residual lateral movement and bending strain are induced in the existing pile after each loading–unloading cycle. This is because plastic deformation is induced in the soil surrounding the existing pile during each loading–unloading cycle. By increasing the applied loads during cyclic loading–unloading process, the lateral movements and bending strains induced in the pile head increase simultaneously. As the cyclic loading varies from 10 to 50 kN, the residual pile head movement increases from 40 to 154?mm, and the residual bending strain of the existing pile varies from 100 to 260 με. The ratio of residual to the maximum pile head movements varies from 0.17 to 0.22, while the ratio of residual to the maximum bending strains is in a range of 0.12–0.55. 相似文献
5.
In the field of ocean engineering, pile foundations are extensively used in supporting several structures. In many cases, piles are subjected to significant lateral loads. The environment prevalent in the ocean necessitates the piles to be designed for cyclic wave loading. In this investigation, the behaviour of rigid piles under cyclic lateral loading has been studied through an experimental programme carried out on model piles embedded in a soft marine clay. Static tests were also conducted on piles embedded in a clay bed prepared at different consistencies suitable to field situations. Cyclic load was applied by using a specially designed pneumatic controlled loading system. Tests were conducted on model piles made of mild steel (MS), aluminium and PVC with wide variation in pile soil relative stiffness. For cyclic load levels less than 50% of static lateral capacity, the deflections are observed to increase with number of cycles and cyclic load level and stabilise after a certain number of cycles. For cyclic load levels greater than 50% of static lateral capacity, the deflections are observed to increase enormously with number of cycles. The results of post-cyclic load tests indicate that the behaviour under static load can improve for cyclic load levels less than 40% of the static lateral capacity. The variations in the load capacity due to cyclic loading are explained in terms of the changes in strength behaviour of soil. 相似文献
6.
A series of centrifuge tests were performed to investigate the response of a free-head monopile due to cyclic lateral loading in normally consolidated clay. By linking the maximum reaction-force point of the final cycles in all tests with various amplitudes, a postcyclic reaction-force curve is obtained, which can be used to assess the postcyclic remolded lateral stiffness. To numerically analyze the tests, a strength degradation model of the clay is calibrated by the T-bar cyclic test. However, this model is T-bar-dependent, which is unable to capture the degrading behavior of the monopile stiffness. Thus, a modification approach is proposed based on the upper bound theory, and the modified model is further combined with finite element analysis to simulate the cyclic behavior of the model pile. The simulation results show similar degrading trend and consistent postcyclic remolded lateral stiffness with the model tests. This further demonstrates that the remolded lateral stiffness mainly depends on the soil remolded strength, which is one of the parameters calibrated by the T-bar tests. Based on this finding, a simplified numerical analysis is proposed, which can predict the postcyclic reaction-force curve by performing one monotonic loading instead of modeling the whole process of cyclic loading. 相似文献
7.
Hiroyoshi Hirai 《Marine Georesources & Geotechnology》2018,36(7):805-817
An investigation was made to present analytical solutions of cyclic response to suction caisson subjected to inclined cyclic loadings in clay using a three-dimensional displacement approach. A model representing the relationship between vertical load and vertical displacement and that between lateral load and lateral displacement along the skirt of suction caisson subjected to cyclic loadings is proposed for overconsolidated clay. For the effect of vertical load on cyclic load capacity of suction caisson, using the Mindlin solution in the case of a vertical point load, the vertical stress of soil under the base of suction caisson is presented. For the stress state of soil beneath the base of suction caisson subjected to cyclic loading, the Mohr–Coulomb failure line and critical state line are presented and the relationship between total stress, effective mean principal stress, stress difference, and pore-pressure is elucidated. The comparison of results predicted by the present method for a suction caisson subjected to cyclic loadings in clay has shown good agreement with those obtained from field tests. Cyclic behavior of clay up to failure is made clear from the relationship between cyclic tensile load, vertical and lateral displacements, and rotation and that between depth, vertical, and lateral pressures. 相似文献
8.
AbstractIn this article, the degradation of the lateral bearing capacity of piles in soft clay subjected to cyclic lateral loading is studied numerically. A modified kinematic hardening constitutive model is employed to simulate the degradation of soft clay after cyclic loading. The modified model is verified by comparing the numerical simulation results with the results of centrifuge model tests. Furthermore, the modified model is applied to numerical simulations for evaluating the lateral bearing capacity of piles in soft clay subjected to cyclic lateral loading. The degradation of the lateral bearing capacity of piles in soft clay after different cyclic displacement levels and different numbers of cycles is investigated. The study reveals that the modified kinematic hardening constitutive model can effectively estimate the cyclic degradation behavior of piles in soft clay subjected to cyclic lateral loading. The degradation of the ultimate lateral bearing capacity progresses slowly with increasing cyclic displacement level for fewer cycles, and the degradation develops significantly at higher levels of cyclic displacement after applying a larger number of cycles. 相似文献
9.
A series of 1 g model tests was conducted to investigate the accumulated vertical pullout displacement and unloading stiffness of bucket foundations embedded in dry and saturated sands. The foundations were subjected to vertical pullout cyclic loading with different load amplitudes. Cyclic load was applied up to 104 cycles. Test results showed that the accumulated vertical pullout displacement increased with the increase in the number of load cycles and cyclic load amplitudes. The unloading stiffness of the bucket foundations decreased with the increase in load amplitude and number of cycles. Empirical equations were proposed based on the test results to evaluate the accumulated vertical pullout displacement and unloading stiffness of the bucket foundations in saturated sand. These equations can be used for the preliminary design of single or tripod bucket foundations. 相似文献
10.
A fundamental study of pile–soil systems subjected to lateral loads in offshore deposit was conducted using experimental tests and numerical analysis. The emphasis was on the soil–pile rigidity of a laterally loaded pile in marine clay. Rigid- and flexible-pile analyses were conducted for comparison. A framework for determining the lateral load transfer curve (p–y curves) is proposed based on both field and laboratory model tests. A numerical analysis that takes into account the proposed p–y curves was performed for the pile flexibility parameters such as pile diameter, pile length, pile-bending stiffness, and the modulus of subgrade reaction. Based on the analysis, it is shown that the differences in bending moment and lateral displacement are more significant for flexible piles rather than rigid piles. It was found that the p–y curves influence the behavior of flexible piles more than rigid piles, thus the magnitude and distribution of the p–y curves are significantly important in flexible pile design. 相似文献
11.
This paper analyzes the long-term monopile foundation that undergoes numerous mechanical cycles. The semiempirical scheme is adopted to involve a mechanical constitutive model to extract stress and strains at the first cycle and polynomial-type strain accumulation functions to track the progressive plastic deformation. In particular, the strain function contains the fundamental features that require simulating the long-term response of geomaterials: volumetric strain (terminal void ratio) and shear strain (shakedown or ratcheting), the strain accumulation rate, and stress obliquity. The numerical simulation shows evolution of displacements, pile rotation, and stress redistribution along the embedded pile as the number of load cycles increases. The analysis highlights that the pile rigidity affects the pattern of horizontal stress and displacement. The repetitive lateral load enhances the lateral load resistance due to soil densification along the pile. 相似文献
12.
Slender piles embedded in soft ground or liquefied soil may buckle under vertical load. In this paper, both small- and large-scale model tests are conducted to investigate the buckling mechanisms of a slender pile and the lateral earth pressure acting on the pile. To observe the buckling of a slender pile, the strain-controlled loading method is adopted to apply a vertical load. When the two ends of a slender pile are hinged, the buckling mechanisms of small- and large-scale model tests are same. It should be noted that this applies only to a system with a small ratio of pile bending stiffness to soil bending stiffness. An applied vertical load increases with an increasing pile head settlement until it reaches the critical buckling load. By further increasing the pile head settlement, the measured load approaches the critical buckling load. In the large-scale model test, the measured lateral earth pressure (i.e., active and passive) acting on the slender pile varies linearly with the lateral pile displacement when the measured range is 3–5?m beneath the ground. A critical buckling calculation method has been adopted to compare with the conventional “m” method. The two-sided earth pressure calculation method can achieve more approximate results with the model test. 相似文献
13.
Hiroyoshi Hirai 《Marine Georesources & Geotechnology》2017,35(8):1121-1134
An investigation was conducted to obtain analytical solutions for the pullout behavior of a suction caisson undergoing inclined loads in sand. The inclined load is transformed into an equivalent load system in which the vertical, horizontal, and moment loads are applied on the center of the lid of the suction caisson. The vertical and lateral stiffness coefficients along the skirt of the suction caisson in sands are presented using the new three-dimensional elastic solutions taking into account the nonhomogeneous and nonlinear properties of the sand. The vertical, lateral, and rocking stiffness coefficients on the base of the suction caisson are presented considering the solutions of a hollow rigid cylindrical punch acting on the surface of a soil. The yield, pullout, and failure for sands with the nonhomogeneous and nonlinear characteristics are taken into consideration. The effects of the load inclination, the loading depth, and the aspect ratio on the pullout load capacity of the suction caisson are presented. Behaviour of the suction caisson in sand prior to failure is clarified from the relationship between tensile load, displacement, and rotation and that between depth, vertical pressure, and lateral pressure. 相似文献
14.
15.
This article reports the response of embedded circular plate anchors to varying frequencies of cyclic loading. The effects of time period of loading cycles and pre-loading on movement of anchors and post-cyclic monotonic pullout behavior are studied using a model circular (80 mm diameter) plate anchor, buried at embedment ratio of six in a soft saturated clay. The frequencies of loading cycles have showed considerable effect on movement of anchors. For given duration of loading, higher frequency cycles cause more movement of anchor than lower frequency cycles. Pre-loading reduces the movement of anchors in subsequent loading stages. When anchors are recycled at a load ratio level less than the pre-cycling load, the movement of anchor in recycling phase are very much reduced, but if the recycling is done at a higher load ratio level, the effect is not that much pronounced and the anchors behave as if they were not subjected to any cycling load in the past. Anchor subjected to cyclic loading and then monotonic pullout shows an increase in initial stiffness, whereas the peak pullout load was found to decrease marginally over that of an anchor not subjected to any cyclic loading. For the present test conditions, the relative post-cyclic stiffness of anchors is found to vary from 1.169 to 1.327. 相似文献
16.
This article reports the response of embedded circular plate anchors to varying frequencies of cyclic loading. The effects of time period of loading cycles and pre-loading on movement of anchors and post-cyclic monotonic pullout behavior are studied using a model circular (80 mm diameter) plate anchor, buried at embedment ratio of six in a soft saturated clay. The frequencies of loading cycles have showed considerable effect on movement of anchors. For given duration of loading, higher frequency cycles cause more movement of anchor than lower frequency cycles. Pre-loading reduces the movement of anchors in subsequent loading stages. When anchors are recycled at a load ratio level less than the pre-cycling load, the movement of anchor in recycling phase are very much reduced, but if the recycling is done at a higher load ratio level, the effect is not that much pronounced and the anchors behave as if they were not subjected to any cycling load in the past. Anchor subjected to cyclic loading and then monotonic pullout shows an increase in initial stiffness, whereas the peak pullout load was found to decrease marginally over that of an anchor not subjected to any cyclic loading. For the present test conditions, the relative post-cyclic stiffness of anchors is found to vary from 1.169 to 1.327. 相似文献
17.
AbstractPile foundation is the most popular option for the foundation of offshore wind turbines. The degradation of stiffness and bearing capacity of pile foundation induced by cyclic loading will be harmful for structure safety. In this article, a modified undrained elastic–plastic model considering the cyclic degradation of clay soil is proposed, and a simplified calculation method (SCM) based on shear displacement method is presented to calculate the axial degradated capacity of a single pile foundation for offshore wind turbines resisting cyclic loadings. The conception of plastic zone thickness Rp is introduced to obtain the function between accumulated plastic strain and displacement of soil around pile side. The axial ultimate capacity of single piles under axial cyclic loading calculated by this simplified analysis have a good consistency with the results from the finite element analysis, which verifies the accuracy and reliability of this method. As an instance, the behavior of pile foundation of an offshore wind farm under cyclic load is studied using the proposed numerical method and SCM. This simplified method may provide valuable reference for engineering design. 相似文献
18.
Sudip Basack 《Marine Georesources & Geotechnology》2013,31(4):356-360
Pile foundations subjected to cyclic load is an age-old problem dealt with for decades by geotechnical engineers. The ocean environment necessitates the piles supporting offshore structures to be designed against lateral cyclic loading initiated by wave action. Substantial experimental and analytical investigations have already been conducted by the author and other researchers. The quasi-static load reversal induces deterioration in the strength and stiffness of the soil-pile system introducing progressive reduction in the bearing capacity as well as settlement of the pile foundation, the degree of such degradation has been observed to be a function of the cyclic load parameters and the type of soil. Based on these observations, a design recommendation has been attempted in this paper for piles subjected to cyclic load in cohesive soil. 相似文献
19.
Hiroyoshi Hirai 《Marine Georesources & Geotechnology》2013,31(4):452-466
ABSTRACTAn investigation is made to present analytical solutions provided by a three-dimensional displacement approach for analysis of bucket foundations subjected to vertical and lateral loads in cohesive soils. The nonlinear vertical and lateral stiffness coefficients along the skirt of the bucket foundation in nonhomogeneous soil are presented using three-dimensional solutions for vertical and lateral loads and taking into account the dependence of stiffness coefficients on the shear strain. The vertical, lateral, and rocking stiffness coefficients on the base of the skirt of a bucket foundation are obtained from the solutions of hollow rigid cylindrical punch acting on the surface of a soil. The ultimate vertical stress of a soil under the base of a bucket foundation subjected to vertical and moment loads is presented analytically by considering only compression and ignoring tension on the base. The vertical and lateral yields along the skirt and the compression and shear failures on the base are taken into account in analysis of ultimate load capacities. Envelopes of the combined ultimate horizontal and moment load capacities of a bucket foundation in clay are shown. Relationships between ultimate lateral and moment load capacities and the embedment ratio (skirt length to diameter) are presented. 相似文献
20.
AbstractMono-pile foundations have been widely used for offshore wind turbines principally due to their convenient construction and cost-effective nature. So far, little attention has been paid to large diameter “semi-rigid” piles that have distinct behaviours from flexible or ideally rigid piles. This paper presents a series of centrifuge model tests to study the deforming and bearing characteristics of a 5.9 dia. semi-rigid pile under lateral loadings in kaolin clay. For monotonic loading, a modified p–y curve analysis model considering rotational soil flow near the rotation centre of pile was proposed, highlighting the limitation of classic plane-strain based plasticity models to evaluate the ultimate lateral pile-soil resistance. For cyclic loading, a strong correlation between the degree of soil degradation and cyclic load amplitude was identified. Besides, a degradation factor model, accounting for various cyclic stress levels and soil depths, was proposed, which can be used to assess the accumulative displacement of semi-rigid piles under cyclic loadings in soft clay. 相似文献