共查询到20条相似文献，搜索用时 140 毫秒
1.
复合加载条件下吸力式沉箱基础承载特性数值分析 总被引：2，自引：0，他引：2
吸力式沉箱基础的承载特性是海洋工程结构设施建造与设计中的一个关键问题。这种新型的深水海洋基础型式,通常承受竖向上拔荷载与水平荷载的共同作用,其工作性能与设计理论远远不能满足工程实践的需要。本文采用有限元分析方法对吸力式沉箱基础的极限承载特性进行数值计算。以大型通用有限元分析软件ABAQUS为平台,通过二次开发,数值实现了Swipe试验加载方法和固定位移比分析方法,针对不同的沉箱长径比、土的强度折减系数,探讨了沉箱基础在垂直上拔荷载和水平荷载单调联合作用下的极限承载力,通过对不同荷载组合的数值计算构造了复合加载条件下沉箱基础破坏包络面。 相似文献
2.
由于预载下土体固结,海底浅基础的承载力会随作业时间的增加而改变,其时变效应评估困难。基于修正剑桥模型,采用水土耦合有限元方法研究了预载作用下浅基础在正常固结黏土海床中承载力破坏包络面的时变规律。在验证数值模型准确性后,通过位移探针测试获取复合加载模式下浅基础的破坏包络面,揭示了预载和固结程度对基础承载力和破坏包络面的影响,给出了预载作用下浅基础承载力包络面计算方法。结果表明：随着预载比增加,固结单轴承载力呈现线性增长,固结承载力增幅在水平向最大;部分固结承载力相对增幅与预载比无关,而随固结度变化;破坏包络面形状由预载比控制,而包络面大小由预载比和固结度共同控制。研究结果可为海洋浅基础的时变承载力评估提供参考依据。 相似文献
3.
针对用于海上风力发电机的伞式吸力锚基础(USAF)实际条件下的受力特点,采用数值模拟方法,基于大型通用有限元软件ABAQUS构建数值计算模型,对伞式吸力锚基础在H-V、H-T、V-T荷载平面内以及H-V-T非共面复合加载模式下的承载特性进行分析,进而推导其破坏包络面数学表达式。分析中采用固定位移比加载法进行复合加载,并将桶顶位移作为失效破坏标准。结果表明：(1)拟定的应力归一化复合加载破坏包络面椭圆曲线方程可以较好地模拟不同主筒长径比USAF在不同荷载空间内的破坏包络面形式;(2)H-T空间内USAF复合承载性能随主筒长径比(L/D)的增大而提高,而H-V、V-T空间内变化不明显;(3)绘制了H-V-T空间内USAF三维破坏包络面,可根据实际受荷状态与包络面之间的相对位置关系,评价实际工况下伞式吸力锚基础的稳定性。 相似文献
4.
针对吸力式沉箱在黏性底床中沉贯安装的减阻问题,基于黏性泥沙的流变特性,开展了一系列不同振动荷载作用下的室内沉贯模型试验,分析了振动荷载对吸力式沉箱沉贯过程的影响和沉贯减阻效果。试验结果表明：在压力沉贯阶段或吸力沉贯阶段施加高频振动荷载,均能促使吸力式沉箱侧壁周围的土体发生流化,有效降低沉箱的沉贯阻力;减阻效果与振动频率和沉箱的长径比有关,与振动频率成正比,与沉箱的长径比成反比;存在一个临界频率,当振动频率大于该频率后,沉贯阻力随频率的减小不明显;施加高频振动荷载有助于减小吸力沉贯阶段沉箱内的土塞高度,促进沉箱沉贯到位。研究成果可为黏性泥沙流变减阻技术在吸力式沉箱中的应用提供理论依据和技术参考。 相似文献
5.
自升式平台作业前需对桩靴基础进行预压安装,使桩靴具备抵抗竖向-水平-弯矩复合荷载的能力。安装过程中,桩靴上部将形成一定深度的孔洞。弱超固结黏土地基中,土体强度较高,桩靴最终贯入深度较浅,而形成的上部孔洞较深,因此孔洞将对桩靴就位后的承载力产生影响。通过有限元分析,研究弱超固结黏土中桩靴上部孔洞对承载力的影响,结果表明:1)与无孔洞的情况相比,孔洞的存在对桩靴的单向和复合承载力有削弱作用; 2)当桩靴与孔洞底部距离大于桩靴直径时,承载力不再受上部孔洞的影响; 3)当桩靴埋深小于等于0.75倍桩靴直径时,无论桩靴上部有无孔洞,现有预测公式都不能较为合理地预测弱超固结黏土地基的复合承载力,为此提出了考虑孔洞影响的桩靴复合承载力包络面预测公式。 相似文献
6.
Spar平台吸力式基础极限承载特性数值分析 总被引：2，自引：0，他引：2
以国外某深海Spar平台工程为背景,针对其所采用的细长型吸力式基础的抗拔承载特性进行三维有限元数值分析.分析中充分考虑土体强度、加载位置和加载角度对吸力式基础极限抗拔承载力的影响,本构模型中钢筒基础采用弹塑性模型.分析结果表明,吸力式基础的极限抗拨承载力随着土体强度的增大而增大,倾斜加载时在基础插入土体部分中点左右加载可取得最大的极限承载力,极限抗拔承载力还随着加载角度的增大而增大.吸力式基础存在倾斜加载时桶基础与桶内外土体的共同塑性屈服破坏和垂直加载时桶外土体的局部剪切破坏等两种不同的破坏模式. 相似文献
7.
针对现阶段深水软黏土地基防波堤建设的设计理论和稳定性分析方法尚不成熟,结合实际工程,采用三维弹塑性有限元数值分析方法,研究在水平或竖直单一方向荷载以及复合加载条件下软黏土地基上沉箱防波堤的失稳模式,提出破坏包络线的稳定性判别方法。在波浪水平荷载作用下,深水软基上沉箱防波堤发生倾覆失稳破坏,失稳转动点为沉箱底面以下中轴线偏右的某点,不同于规范中规定的岩石或砂质地基沉箱倾覆转动点为其后踵点;在重力等竖向荷载作用下,沉箱的失稳模式为结构整体下陷,抛石基床及地基形成连贯的塑性区域,呈现较明显地冲剪破坏形式;在水平、竖向复合荷载作用下,软基上沉箱防波堤的破坏包络线由结构倾覆破坏线和地基承载力破坏线组成,包络线将荷载组合区分成稳定区、仅发生水平承载力不足倾覆破坏区、仅发生地基竖向承载力不足破坏区、同时发生水平承载力和地基竖向承载力不足破坏区4个区域。研究成果为深水软基沉箱防波堤建设提供参考和借鉴。 相似文献
8.
基于验证的三维有限元方法,考察了斜壁桶形基础的承载特性,得到了变形网格、位移增量分布、位移等值面分布等结果,探讨了斜壁倾角与各极限承载力之间的定量关系。计算表明,桶形基础发生竖向位移时,主要是桶体内部和桶基正下方的土体发生沉降,而桶侧的土体基本不发生沉降。桶形基础受到水平荷载发生转动时,转动中心轴大致位于桶基底面内,桶基水平承载力主要由桶内土体和桶基外侧中上部受压侧土体产生的抵抗反力构成。桶基因受到较大竖直向上荷载而失效时,桶内土体和桶基外侧靠近海床面附近土体产生了较大的向上位移。桶壁倾角β每增加1°,竖向抗压极限承载力、竖向抗拔极限承载力、水平极限承载力分别提高12%、17.4%及3.8%。 相似文献
9.
针对深水平台吸力沉箱基础,讨论了与沉箱安装有关的分析方法及涉及的工程地质参数,分析了承受竖向拉拔荷载、倾斜与水平荷载作用的吸力沉箱极限承载力的分析方法及涉及的工程地质参数,对与吸力沉箱设计有关的其它问题也进行了分析.在此基础上,阐明了与吸力沉箱设计有关的工程场地调查内容及需要确定的工程地质参数.其目的是为开发深水平台吸... 相似文献
10.
张其一 《中国海洋大学学报(自然科学版)》2013,(4):100-105
海洋工程中结构物除了受到自身重力作用外,往往还受到海风、海浪、海流等的作用,使得海床土体中的基础一般受到集中力、弯矩和扭矩的联合作用,这一受力状态称为结构物基础的复合加载模式。本文以复合加载模式下海床土体变形规律与失稳机理为研究对象,基于通用有限元分析软件Abaqus,采用数值计算方法,对海床土体的极限承载能力进行了详细的研究。结果表明,荷载分量大小与组合形式对海床失稳机理与极限承载能力具有较大影响,H-M荷载空间内破坏包络面具有非对称性。本文给出的土体失稳模式,能够较为合理地评估复合加载模式下海床土体的变形规律;给出的土体极限力矩荷载判别准则,能够较为合理地计算海床土体的极限力矩荷载。 相似文献
11.
Suction caissons are widely used to support offshore fixed platforms in coastal areas. The loadings transferred to suction caissons include the eccentric lateral force induced by waves and self weight of the platform structure. However, under this kind of combined loading conditions, the failure mechanism of caissons with shallow embedment depths is quite different from conventional deep foundations or onshore shallow footings. The behaviour of caissons subjected to combined loadings may be described with the "failure locus" in force resultant spaces. Here the failure loci of smooth caissons are studied by use of finite element approach, with the embedment ratio of caissons varying in the range of 0.25～1.0 and eccentricity ratio of horizontal loadings in 0～10. The platform settlement and tilt limits are involved into determination of failure loci, thus the platforms can avoid significant displacements for the combined loadings located inside the failure locus. Three families of loading paths are used to map out the locus. It is found that the shape of failure loci depends on 3 non-dimensional parameters, and the failure locus of a given caisson changes gradually from the elliptical curve to hooked curve with increasing shear strength of soil. The lateral capacity of short caissons may be enhanced by vertical forces, compared with the maximum lateral capacity of long caissons occurring at the vertical force being zero. The critical embedment ratios partitioning elliptical and hooked loci are proposed. 相似文献
12.
A series of model tests were performed on steel- and Perspex-made suction caissons in saturated dense marine sand to explore installation and extraction behaviors. The extractions of the caisson were conducted by applying monotonic loading or by pumping water into the caisson. Responses of suction caissons to pullout rates, aspect ratios, and extraction manners were examined. Test results show that a cone-shaped subsidence region occurs around the suction caisson during the suction-assisted installation. The pullout bearing capacity of the suction caisson in sand is dominated by the loading rate and the loading manner. For the suction caisson subjected to monotonic loading, the maximum bearing capacity is reached at the pullout rate of about 20.0?mm/s. The mobilized vertical displacement corresponding to the pullout capacity increases with increasing the pullout rate. The passive suction beneath the suction caisson lid reaches the maximum value when the pullout bearing capacity is mobilized. In addition, during the suction caisson extracted by pumping water into the caisson, the maximum pore water pressure in the caisson is obtained under the displacement of approximately 0.04 times the caisson diameter. The absolute values of the maximum pore water pressures for the suction caissons approximately equal those of the maximum vertical resistances at the monotonic pullout rate of 5 mm/s. When the vertical displacements of the suction caissons with the aspect ratio of 1.0 and 2.0 reach 0.92 and 1.77 times the caisson diameter, respectively, the seepage failure occurs around the caissons. Using a scaling method, the test results can be used to predict the time length required for the prototype suction caisson to be extracted from the seabed. 相似文献
13.
Determining the ultimate capacity of suction caissons in response to combined vertical, horizontal, and moment loading is essential for their design as foundations for offshore wind turbines. However, the method implemented for stability analysis is quite limited. Numerical limit analysis has an advantage over traditional limit equilibrium methods and nonlinear finite element methods in this case because upper and lower bounds can be achieved to ensure that the exact ultimate capacity of the caisson falls within the appropriate range. This article presents theories related to numerical limit analysis. Simulations are conducted for centrifuge model tests, the findings of which reveal the ability of numerical limit analysis to deal with the inclined pullout capacity of suction caissons. Finally, this article proposes an estimation of the ultimate capacity of a 3.5 MW offshore wind turbine foundation on normally consolidated clay based on the typical environmental parameters of Bothkennar, Scotland. Undrained failure envelopes and safety factors are obtained for suction caissons with different embedment ratios. Failure mechanisms, plastic zones, clay stress distributions, and the influence of the skin friction coefficients of caissons are discussed in detail. 相似文献
14.
A series of model tests was conducted in sand to explore the anti-uplift behavior of suction caissons, considering the effects of aspect ratios, load inclination angles and loading positions. This paper emphasizes on analyzing the deformation characteristic and the mechanism of the suction caissons under various loading conditions. The movement modes of the suction caisson are different when the load inclination angle increases from 0° to 90° corresponding to various mooring positions. The pull-out bearing capacity decreases with load inclination angles increasing. When the load inclination angle changes from 0° to 60°, the bearing capacity reduces more significantly than that between inclination angle of 60° and 90°. While the load inclination angle is relatively small, the pull-out capacity of the suction caisson decreases after reaching the peak as the loading position moves downwards. Moreover, the optimum loading position locates between 2/3 and 3/4 of the caisson length. The optimum loading position is at the bottom of the caisson when the load inclination angle exceeds 60°. However, the influence of the loading position on the pull-out capacity of the caisson can be ignored while the load inclination angle equals to 90°. The pull-out bearing capacity increases as the aspect ratio increases but the aspect ratio has no effect on the deformation characteristic of the suction caisson. 相似文献
15.
1 .IntroductionSuctioncaissons have been widely usedfor offshore oil exploration duetothe advantages of econo-my and simple installation over traditional piles (Huanget al .,2003) .For tensionleg platforms andspar platforms in deep ocean,suction caissons … 相似文献
16.
Response of skirted suction caissons to monotonic lateral loading in saturated medium sand 总被引：2，自引：1，他引：1
Monotonic lateral load model tests were carried out on steel skirted suction caissons embedded in the saturated medium sand to study the bearing capacity. A three-dimensional continuum finite element model was developed with Z_SOIL software. The numerical model was calibrated against experimental results. Soil deformation and earth pressures on skirted caissons were investigated by using the finite element model to extend the model tests. It shows that the ＂skirted＂ structure can significantly increase the lateral capacity and limit the deflection, especially suitable for offshore wind turbines, compared with regular suction caissons without the ＂skirted＂ at the same load level. In addition, appropriate determination of rotation centers plays a crucial role in calculating the lateral capacity by using the analytical method. It was also found that the rotation center is related to dimensions of skirted suction caissons and loading process, i.e. the rotation center moves upwards with the increase of the ＂skirted＂ width and length; moreover, the rotation center moves downwards with the increase of loading and keeps constant when all the sand along the caisson＇s wall yields. It is so complex that we cannot simply determine its position like the regular suction caisson commonly with a specified position to the length ratio of the caisson. 相似文献
17.
The passive suction of suction foundations plays a significant role in pull-out resistance. The factors influencing the uplift capacity include stress state, embedment ratio, and loading rate. This article investigates the effect of embedment ratio and loading rate on the bearing behavior of suction foundations using centrifuge testing. A series of uplift tests on a suction foundation in clay were performed using a beam centrifuge. During the tests, uplift displacement, suction, and loading rate were monitored. The suction was obtained by measurement of water pressure. To compare the influence of different factors on uplift capacity due to passive suction, two types of uplift tests were conducted; the first was on the closed caisson and the second was on the vented caisson. The results show that the pull-out resistance increased with an increase of the uplift loading rate, which was induced by the suction. The maximum resistance occurred when the upward displacements reached 14%D under a ratio of skirt length (L) to diameter (D) (L/D) of 0.5 and 17%D under an L/D ratio of 2. These findings provide a way for suction caissons to resist pull-out load or for structures to be removed from the seabed. 相似文献
18.
To study the feasibility and efficiency of underwater suction anchors in soil, the performance of eight model anchors was evaluated in a 30 in. (76·2 cm) by 72 in. (183·0 cm) by 32 in. (81·3 cm) deep test tank. The soil studied were a medium fine sand, a silt and a clay. A gantry-type loading mechanisms was used to apply the vertical breakout force. A pullout rate of approximately 0·1 in/min (0·25 cm/min) was used for all tests.For the range of conditions studied, the test results indicate that the underwater suction anchor is feasible and effective. The breakout behavior of the suction anchors depends upon the anchor geometry including anchor diameter and skirt length, soil strength properties, soil-anchor friction and adhesion, and suction; i.e. the difference between the pressure underneath the porous plate and the ambient pressure. For the anchors and soils tested, the anchor capacity increases linearly with increasing suction provided the anchor skirt length to diameter ratio remains constant. An increase in the anchor capacity results with increasing suction and with increasing internal friction angle of the test soils. To study the results suggest that the underwater suction anchor is particularly useful for short-term anchorage. 相似文献
19.
A series of model tests were conducted on Perspex-made suction caissons in saturated dense marine sand to study the sand plug formation during extraction. Suction caissons were extracted by pullout loading or by pumping air into the suction caisson. Effects of the pullout rates, aspect ratios and loading ways (monotonic or sustained) on the pullout capacity, and plug formation were investigated. It was found that the ultimate pullout capacity of the suction caisson increases with increasing the pullout rate. The sand plug formation under the pullout loading is significantly influenced by the pullout rate and the loading way. When the suction caisson is extracted at a relatively slow rate, the general sand boiling through the sand plug along the inner caisson wall occurs. On the contrary, the local sand boiling will occur at the bottom of the suction caisson subjected to a rapid monotonic loading or a sustained loading. Test results of the suction caisson extracted by pumping air into the caisson show that the pressure in the suction caisson almost follows a linear relationship with the upward displacement. The maximum pressures for suction caissons with aspect ratios of 1.0 and 2.0 during extraction by pumping air into the caisson are 1.70 and 2.27 times the maximum suction required to penetrate the suction caisson into sand. It was found that the sand plug moves downward during extraction by pumping air into the caisson and the variation in the sand plug height is mainly caused by the outflow of the sand particles from the inside of the suction caisson to the outside. When the suction caisson model is extracted under the pullout rate of 2?mm/s (0.28?mm/s for the prototype), the hydraulic gradient along the suction caisson wall increases to the maximum value with increasing the penetration depth and then reduces to zero. On the contrary, when extracted under the pullout rate of 10?mm/s (1.4?mm/s for the prototype), the hydraulic gradient along the suction caisson wall increases with increasing the pullout displacement. When extracted by pumping air into the caisson, the hydraulic gradient reaches the critical value, and at the same time, the seepage failure occurs around the suction caisson tip. 相似文献
20.
Suction caisson foundation derives most of their uplift resistance from passive suction developed during the pullout movement. It was observed that the passive suction generated in soil at the bottom of the caisson and the failure mode of suction caisson foundation subjecting pullout loading behaves as a reverse compression failure mechanism.The upper bound theorems have been proved to be a powerful method to find the critical failure mechanism and critical load associated with foundations, buried caissons and other geotechnical structures. However, limited attempts have been reported to estimate the uplift bearing capacity of the suction caisson foundation using the upper bound solution. In this paper, both reverse failure mechanisms from Prandtl and Hill were adopted as the failure mechanisms for the computation of the uplift bearing capacity of the suction caisson. New equations were proposed based on both failure mechanisms to estimate the pullout capacity of the suction caisson. The proposed equations were verified by the test results and experimental data from published literature. And the two solutions agree reasonably well with the other test results. It can be proved that both failure mechanisms are reasonably and more consistent with the actual force condition. 相似文献