共查询到20条相似文献，搜索用时 281 毫秒
1.
通过物理模型试验研究中国《海港水文规范》(JTJ213-98)中斜坡式防波堤顶部胸墙波浪力计算公式在深水情况下的适用性.试验测量4种不同水深波浪作用下斜坡堤顶部胸墙的波浪力和作用高度.通过对胸墙迎浪面的波浪压强分布、总水平作用力和波浪作用高度的试验结果与《海港水文规范》结果的对比分析,发现胸墙迎浪面的实测波压分布不同于规范采用的均匀分布;规范计算得到的总水平力和波浪作用高度均小于实测值.本文改进规范中斜坡堤胸墙波浪力计算方法,使其更适用于深水堤顶部胸墙受力计算. 相似文献
2.
斜坡堤典型胸墙波浪力的影响因素 总被引：2，自引：1，他引：1
为探求斜坡堤典型胸墙迎浪面所受波浪力大小的影响因素,设计前仰式、深弧式、后仰式和直立式4种结构型式胸墙进行相关的物理模型试验。通过在典型胸墙迎浪面间隔布置压力测点,获取所受波浪压力,并将其进行积分求和,得到胸墙所受波浪力,进而讨论相对波高、相对波长、斜坡坡度和胸墙结构型式对波浪力的影响。结果表明,相对波高与相对波长对胸墙所受波浪力影响显著;波浪力随着相对波高的增大而增大,随着相对波长的增大呈现先增大、后减小、再增大的变化趋势;波浪力随着斜坡坡度的增大而减小。斜坡堤弧形胸墙所受波浪力明显大于直立式胸墙所受波浪力;在斜坡堤弧形胸墙中,前仰式胸墙受力较其余两种型式胸墙受力小。研究结果将加深波浪对斜坡堤胸墙作用力的理解,为后续工程设计提供理论指导。 相似文献
3.
在印度洋、大西洋沿岸，海岸工程设计波浪周期多在14 s以上，具有显著的中长周期波特征。通过以往工程项目的试验结果发现中长周期波下，规范计算的斜坡堤胸墙波浪力明显小于试验结果。因此，通过系列物理模型试验研究了中长周期波下的斜坡堤胸墙波浪力。分析斜坡坡度、肩台宽度和波浪条件对胸墙波浪力的影响。通过将试验结果与我国现有规范中的经验公式计算所得结果进行对比，发现规范更适用于胸墙底淹没的情况，而对于肩台出水情况，规范计算结果小于试验结果。由此提出了一种新的波浪力计算方法，计算准确度得到明显提高。 相似文献
4.
为探求斜坡堤典型胸墙迎浪面所受波浪力大小的影响因素,设计前仰式、深弧式、后仰式和直立式四种结构型式胸墙进行相关的物理模型试验。通过在典型胸墙迎浪面间隔布置压力测点获取所受波浪压力,并将其进行积分求和得到胸墙所受波浪力,进而讨论相对波高(H/d)、相对波长(L/d)、斜坡坡度和胸墙结构型式对波浪力的影响。试验结果表明：相对波高与相对波长对胸墙所受波浪力影响显著。波浪力随着相对波高的增大而增大,随着相对波长的增大呈现先增大—后减小—再增大的变化趋势。波浪力随着斜坡坡度的增大而减小。斜坡堤弧形胸墙所受波浪力明显大于直立式胸墙所受波浪力;在斜坡堤弧形胸墙中,前仰式胸墙受力较其余两种型式胸墙受力小。研究结果将加深波浪对斜坡堤胸墙作用力的理解,为后续工程设计提供理论指导。 相似文献
5.
现行规范中未就扭王字块体护面斜波堤胸墙水平波浪力的计算方法做出具体规定,造成工程设计时使用不便。为解决上述问题,通过物模试验分析在波陡等六种因素的影响下,扭王字块体护面斜波堤胸墙水平波浪力的变化趋势。同时运用非线性拟合方法,遵循π定理,给出斜坡堤在扭王字块体条件下胸墙水平波浪力的计算公式。并对计算公式进行有效验证,该公式具有较好的精确性与适用性。研究成果丰富了规范内容,并为斜坡堤工程设计中胸墙水平波浪力折减系数的合理取值提供了参考依据。此研究成果对于斜坡堤科学研究领域和工程设计领域,都具有很大的参考价值。 相似文献
6.
本研究设计前仰式、深弧式和后仰式3种弧形胸墙以及直立式胸墙进行物理模型试验,通过安装在胸墙迎浪面上的压力传感器测量所受波浪压力,讨论不同型式斜坡堤弧形胸墙迎浪面所受波浪压力的分布规律及其影响因素。试验结果表明:弧形胸墙迎浪面所受波浪压力随着测点高程的增大呈现振荡减小的变化趋势,最大值出现在弧顶处。随着入射波周期的增大呈现先增大后减小再增大的变化趋势。相同波浪要素条件下,斜坡堤弧形胸墙波浪压力大于直立式胸墙波浪压力;而在斜坡堤弧形胸墙中,后仰式胸墙波浪压力较前仰式和深弧式的大。 相似文献
7.
8.
不同掩护程度弧形胸墙波压力及越浪量试验研究 总被引：1，自引：0，他引：1
为了明确斜坡堤弧形胸墙越浪量及波压力的变化规律,采用波浪水槽试验测量了弧形胸墙的越浪量和波压力。试验从斜坡堤弧形胸墙前的掩护程度等因素入手对弧形胸墙的返浪效果及波压力进行初步研究,得出不同掩护程度弧形胸墙的越浪量及波压力,发现掩护程度越好,弧形胸墙所受波压力越小;半掩护情况下越浪量最小,为实际工程设计提供了依据。 相似文献
9.
10.
11.
基于粘性流模型的筒型基础防波堤波浪力数值分析 总被引：3，自引：0，他引：3
筒型基础防波堤是一种新型港口海岸工程结构,其基础上部是由连续排列的圆筒构成的直立防浪墙.采用粘性流数值模型,研究连续圆筒防波堤上波浪力竖向分布、水平(沿圆筒环向)分布和波浪力合力特性,并对粘性流数值模型计算的平面直墙波浪力与海港水文规范方法计算结果;粘性流数值模型计算的连续圆筒墙面波浪力与平面直墙波浪力;无限长连续圆筒墙面波浪力与有限长连续圆筒墙面波浪力进行比较分析.针对所选工程算例,建议按<海港水文规范>中平面直墙波浪力计算方法确定连续圆筒防波堤上的波浪力时,波峰时考虑0.90左右的折减系数,波谷时考虑0.95左右的折减系数. 相似文献
12.
Experimental Investigation of Irregular Wave Uplift Force on Deck of Exposed High-Pile Jetties 总被引：1，自引：0，他引：1
A laboratory setup was developed to investigate irregular wave uplift loads on exposed high-pile jetties.It is shown that the dimensionless uplift load increases to the maximum with an increasing relative clearance and then decreases.The relative clearance corresponding to the peak force is linked to a range from 0.4 to 0.8.When the relative clearance exceeds a certain value,the wave can not reach the underside of the deck and the force becomes zero.Distinct trends of dimensionless force with a relative width of deck show that the force tends to decrease as the relative deck width increases,and then the decrease slows down after the relative deck width increases or decreases to a certain value.The pressure distribution length associated with the maximum uplift force is equivalent to the wave contact width x.When x is larger than the width of deck B,it is taken as B.The statistical distribution of loads obeys the Weibull distribution.The results from the analyses of the real data suggest a new dimensionless prediction model on wave-in-deck uplift loads and the conversion ratio between wave loads at different exceedance probabilities.A comparison is made between the new prediction model and the existing widely used three prediction models.These results are used as useful references for structural design of the jetty. 相似文献
13.
Analysis of Wave Loads on A Semi-Submersible Platform 总被引：10，自引：0，他引：10
For the global and structural fatigue strength analysis of a semi-submersible platform, wave loads under design conditions are calculated by use of the three-dimensional boundary element method. Methods for calculating the forward-speed free-surface Green function are discussed and a computer program with this Green function is developed. According to the special rules, the wave loads under several typical design conditions of the platform are calculated. The maximum vertical bending moment, torsion moment and horizontal split force are determined from a series of contour maps of wave loads for the wave period of 5 to 18 seconds at a certain interval and the wave phase of 0°to 360°at a certain interval. The wave height is determined by the function of wave period with a given exceedance probability. The maximum wave loads under the combination of wave parameters are used as the input of hydrodynamic pressure in the three-dimensional finite element analysis process. The transfer functions of wave loads 相似文献
14.
The semi-empirical formulae by Pedersen (1996) for wave loads on vertical front faces of stiff crown walls are based on model tests with deep and intermediate water wave conditions. A new series of model tests performed at the same test facility as used by Pedersen has revealed that the formulae by Pedersen overpredict the loads in shallow water wave conditions. This paper presents a modification/expansion of the formulae to cover loads in both deep and shallow water wave conditions. The modification is based on a series of 162 physical model tests on typical rubble mound breakwaters with crown wall superstructures. The implementation of shallow water wave conditions in the formulae is done by modifying the term for wave run-up to be dependent on the incident wave height distribution. Moreover, the adjusted formulae provide more accurate estimates of the wave loads on free walls without front armour protection. Pressure transducers with very high eigen-frequencies were used in the present model tests as opposed to the transducers applied by Pedersen which in some cases seem to have been affected by dynamic amplifications. 相似文献
15.
极限波浪载荷是导致海上结构物疲劳失效的主要载荷之一。固定在海洋基础结构物上的直立开孔墙对减小波浪载荷具有一定的效果。基于不可压缩黏性流体流动理论和N-S方程,采用VOF与Level-set相结合追踪自由表面的方法,首先建立数值波浪水槽,然后对开孔墙本身的开孔率和开孔墙与直立墙之间的相对距离,在降低反射系数和波浪力两个方面进行分析。研究结果表明,开孔墙可以明显降低作用在结构物上的波浪力,开孔墙本身的开孔率和与直立墙的相对距离会对其产生明显影响;不同波浪参数下会存在一个最佳的开孔率,但是不同波浪参数时最佳开孔率会略有不同;当开孔墙和直立墙的相对距离在0.2到0.3之间时,开孔墙的消波减载效果最佳。研究结果可为海洋工程相关设计提供一定的参考。 相似文献
16.
This paper concerns the calculation of wave height exceedance probabilities for nonlinear irregular waves in transitional water depths, and a Transformed Rayleigh method is first proposed for carrying out the calculation. In the proposed Transformed Rayleigh method, the transformation model is chosen to be a monotonic exponential function, calibrated such that the first three moments of the transformed model match the moments of the true process. The proposed new method has been applied for calculating the wave height exceedance probabilities of a sea state with the surface elevation data measured at the Poseidon platform. It is demonstrated in this case that the proposed new method can offer better predictions than those by using the conventional Rayleigh wave height distribution model. The proposed new method has been further applied for calculating the total horizontal loads on a generic jacket, and its accuracy has once again been substantiated. The research findings gained from this study demonstrate that the proposed Transformed Rayleigh model can be utilized as a promising alternative to the well-established nonlinear wave height distribution models. 相似文献
17.
This paper concerns the calculation of wave height exceedance probabilities for nonlinear irregular waves in transitional water depths, and a Transformed Rayleigh method is first proposed for carrying out the calculation. In the proposed Transformed Rayleigh method, the transformation model is chosen to be a monotonic exponential function, calibrated such that the first three moments of the transformed model match the moments of the true process. The proposed new method has been applied for calculating the wave height exceedance probabilities of a sea state with the surface elevation data measured at the Poseidon platform. It is demonstrated in this case that the proposed new method can offer better predictions than those by using the conventional Rayleigh wave height distribution model. The proposed new method has been further applied for calculating the total horizontal loads on a generic jacket, and its accuracy has once again been substantiated. The research findings gained from this study demonstrate that the proposed Transformed Rayleigh model can be utilized as a promising alternative to the well-established nonlinear wave height distribution models. 相似文献
18.
基于线性势流假定,对斜向波作用下带横隔板局部开孔沉箱防波堤的水平波浪力进行了理论研究。给出了开孔沉箱法向水平力和横隔板受力的理论计算方法,在极限情况下波浪力的计算结果与文献中的已有结果一致。利用数值算例分析了开孔沉箱总水平力的主要影响因素。开孔沉箱法向总水平力的减小主要集中于结构上半部分波浪影响范围以内。增加单个开孔沉箱的长度有利于减小结构所受总水平波浪力。当波浪入射角或沉箱前开孔墙孔隙影响系数幅值较大时,开孔沉箱横隔板上总水平力的最大值要超过相应的沉箱法向总水平力,此时要注意横隔板的强度问题。 相似文献
19.
关于小直径垂直桩柱结构的波浪力研究 总被引：5，自引：0，他引：5
本文归纳了应用Morison方程中涉及的研究成果。分别从阻力系数和惯性力系数。规则波与不规则波，二阶力和线性化，桩群受力等方面进行了论述。对目前该领域的研究给出了系统的介绍。 相似文献
20.
Shoreline structures are subjected to breaking wave loads which may reach 690 KN/m2. One possibility to reduce these loadings is to slope the exposed surface backwards. The possible amount of reduction in breaking wave loads is, however, unclear, and recent model tests indicated that sloped walls might be exposed to higher loads than are vertical walls. Within the Wave Energy Group at Queen's University Belfast, tests on a 1/36 model of a shoreline wave power station were conducted in order to assess the influence of front wall inclination on the magnitude of breaking wave pressures. It was found that breaking wave pressures decrease from 100% for the vertical wall to 44% for a 32.7° backwards inclined wall and to 64% for a 32.7° forward inclined wall. From the results it was concluded that a maximum pressure of 105% can be expected for a 10° forward inclined wall. Design recommendations were found to be conservative. 相似文献