首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 46 毫秒
1.
美国ODOM公司是国际上著名的测深仪生产厂家。1993年,该公司开发了多波束测深仪,并把PVDF换能器技术成功地应用于换能器设计。本文简要介绍了海洋地貌测量技术的发展,并以其多波束测深仪所采用的PVDF条带换能器技术为例,从理论及实验两方面,阐述了PVDF换能器技术的先进性。  相似文献   

2.
多波束条带测深仪的增益控制方案   总被引:1,自引:0,他引:1  
分析了海底混响的特点以及多波束条带测深仪的工作原理,提出了信号幅度归一化方法-滑动窗TVG方法和自动增益控制方法。  相似文献   

3.
多波束测深系统的精度评估方法研究   总被引:3,自引:1,他引:2  
在分析了多波束测深系统测量误差来源的基础上,讨论了多波柬测深系统静态精度、相对精度和绝对精度的系统精度评估方法。采用的静态精度评估方法就是在多波柬测深系统静止的条件下考核其对同一位置测量深度的误差;相对精度评估方法就是布设多条交叉重叠的测线,考核交叉重叠点的测深误差;绝对精度评估方法是在多波束测深的同时利用高精度的测深仪测量同一区域,用此参考地理模型来检验多波束测深的精度。根据误差理论,三种精度评估的方法分别从系统稳定性、自符合性和系统误差方面确定各误差源的综合误差,它们是检验多波束测深系统精度是否符合海道测量标准的有效方法。文中给出了系统试验数据的重要结果及设备验收的方法。  相似文献   

4.
在系统分析多波束测深数据的误差来源与性质的基础上,介绍了条带式多波束测深仪所采用的误差处理的理论模型。针对海洋测量的特点,特别强调了基于趋势面分析的粗差探测与剔除和相邻条带数据的整体拼接以及对航向  相似文献   

5.
分析了声速剖面测量方法及其误差对多波束测深数据精度的影响.根据多波束测深仪45°倾角渡束测深数据对声速剖面误差不敏感的现象,提出了利用多波束测深仪45°倾角波束测深数据确定声速剖面的A-法并结合检查线计算测线交叉区特征点声速剖面误差,为测区声速剖面的外推提供控制,从而减小声速剖面测量误差对多波束测深的影响提高测深数据精度.  相似文献   

6.
根据多波束测深仪的声纳方程,提出多波束测深仪有效扇面宽度概算方法。通过多波束测深仪声学设计原理估计多波束测深仪的声学参数。分别对各波束的目标强度和声源级进行估算,给出了不同工作深度和工作脉宽情况下的各波束声源级分布,通过检索各波束的声源级确定多波束测深仪的有效扇面宽度,并对测船的选择提出建议。  相似文献   

7.
SeaBat 9001S多波束系统及其应用   总被引:4,自引:0,他引:4  
与传统的单波束回声测深仪相比,多波束测深系统采用条带测量方式,可对水底进行全覆盖无遗漏扫测,在测量自动化、效率和精度方面都具有极大的优点。本文介绍了SeaBat9001S浅水型多波束及前视声纳系统在长江某水下抛石护底工程监理中的应用。  相似文献   

8.
与传统的单波束回声测深仪相比,多波束测深系统采用条带测量方式,可对海底进行全覆盖无遗漏扫测,在测量自动化、效率和精度等方面都具有极大的优点。本文介绍了Simrad EM950浅水型多波束测深声纳系统及其在亚欧海底光缆路由调查中的应用。  相似文献   

9.
刘冲  罗宇 《海洋测绘》2019,39(2):50-53
常规波束形成技术以其稳健性好、计算量低等特点得到广泛应用,但其空间分辨率受阵元个数限制,不能突破瑞利限。因此,常规波束形成技术应用于高精度浅水多波束测深仪时,存在空间分辨率不足和旁瓣干扰等问题。对比研究了最小方差无失真(MVDR)及多重信号分类(MUSIC)波束形成在浅水多波束测深仪中的应用,给出了浅水多波束测深仪的常规波束形成、MVDR和MUSIC处理方法,并结合能量法和相位法两种底检测测深算法,处理了iBeam8120浅水多波束测深仪外场数据,验证了本文方法的性能。  相似文献   

10.
基于HY1621多波束测深仪的多次研制试验,利用不同水域的测试数据,重点分析了HY1621多波束测深仪的测深稳定性、边缘波束稳定性以及测量精度。通过对比分析HY1621和T50-P多波束对新安江水库区域的水下地形扫测成果,以及对HY1621多波束在长江三峡库区的水下地形扫测成果所做的分析,验证了HY1621是一款达到预期性能设计指标的多波束测深仪。  相似文献   

11.
In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance.  相似文献   

12.
An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm.  相似文献   

13.
海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明:土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。  相似文献   

14.
The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths.  相似文献   

15.
Oedometer tests have been carried out on 70 undisturbed surficial clays (at approximately 250 mm below the mudline), mostly collected by free-fall corers from sites widely scattered throughout the deep-sea North Atlantic. Acoustic measurements were also made, initially on contiguous samples and ultimately on the same sample using a geophysically instrumented oedometer which also collected electrical resistivity data. Apart from those quiescent areas below the carbonate compensation depth, such as north of the West Indies where very fine clays exist, most of the samples are silty clays whose geotechnical-geophysical properties are dependent on the type of clay minerals present (and their ability to take in moisture), the sand-size fraction, and the quantity of carbonate present. Thus the pure clays have high compressibilities which decrease on the addition of coarse particles, while the converse is true for the acoustic parameters, these increasing with the sand fraction. Using the notion of the intrinsic compression line for all samples, and comparison to it of the measured compression curves, it is clear that, contrary to some previously held ideas, most deep-sea clays are normally consolidated; the addition of carbonate has the effect of creating an open, stronger sediment skeleton. Interestingly, where information is available, the variation with depth of a sample's acoustic velocity follows the void ratio pressure relationship of the compression curve. This allows the construction of an in-situ sediment compression curve using the in-situ geophysical observations.  相似文献   

16.
《海洋学报(英文版)》2014,(8):F0003-F0003
<正>Acta Oceanologica Sinica(AOS)is a comprehensive academic journal edited by the Editorial Committee of Acta Oceanologica Sinica and is designed to provide a forum for important research papers of the marine scientific community which reflect the information on a worldwide basis.The journal publishes scholarly papers on marine science and technology,including physics,chemistry,biology,  相似文献   

17.
18.
Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement.  相似文献   

19.
This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested.  相似文献   

20.
This article presents a methodology developed to evaluate the instability of submarine slopes that extend over a large area. Special attention was paid to (1) the complex geometry (bathymetry) and the expanse of the slope, (2) the heterogeneity of the sediment, and (3) the distribution of the pore pressure. The safety factor was considered as a spatially varying quantity. The General Formulation (GLE, Fredlund and Krahn 1977), which fully satisfies equilibrium conditions, was used for evaluating the stability of the marine slope. The submarine slope failure, which occurred on 16 October 1979 during the construction of the new Nice airport, was studied in order to test the developed model. Geotechnical parameters were taken from experimental tests carried out by IFREMER on 19 cores extracted at different depths (from 27 m to 1300 m) (Cochonat, Bourillet, and Savoye, 1993; Mulder et al., 1994). Many scenarios were proposed in order to explain the cause of the Nice slope failure (Habib, 1994). In this article, two of those scenarios were tested. Simulation results are presented and discussed.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号