共查询到20条相似文献，搜索用时 93 毫秒
1.
一、研究目的和现状波浪水质点的漂流速度U(亦称波浪传质速度),使波浪破波带的悬沙和底沙产生向岸和离岸横向运动,且当波浪进入水流区后,由于波浪水质点存在漂流速度,所以,除水流使波浪原始要素发生改变外,波浪也在不同程度上改变着流场,可见波浪水质 相似文献
2.
波浪破碎是海洋中最常见的现象之一,其能够对海洋中的结构物产生巨大的波浪力作用。本文在大比尺波浪水槽通过聚焦波的方法生成了极端波浪和不同破碎阶段的破碎波浪,并对其冲击桩柱过程中的点压力进行了测量,进而采用连续小波变换的方法,对桩柱上点压力的分布及大小进行了细致分析。结果表明,多次重复试验下,相比非破碎极端波浪,破碎极端波浪产生的点压力离散性更强;波浪破碎程度越大,测点位置越靠近波峰,则点压力离散程度越大;破碎波的最大点压力出现在1.2倍的最大波面附近,且其大小可达3倍的最大静水压力;基于点压力小波谱,不同破碎阶段破碎波产生冲击作用不同,对于波浪作用桩柱前波浪已经发生破碎的情况,其冲击区域更大,点压力分布更复杂;而对于桩面破碎的情况,其造成的波浪总力更大。 相似文献
3.
4.
通过大尺度水槽波浪引起泥沙悬移的动床模型实验,研究了沙坝海岸破波带内水底悬沙浓度形成机理,通过比较时间平均水底悬沙浓度与时间平均水底波浪水质点动能或时间平均水底湍动能之间的相关性,论证了利用时间平均湍动能比利用时间平均波浪水质点动能计算时间平均水底悬沙浓度更为适用,并提出了以上时间平均水底悬沙浓度与水底湍动能之间的关系也可以用来近似表达时间变化的水底悬沙浓度与时间变化的水底湍动能之间的关系。研究针对规则波、波群和不规则波3种波浪形态进行,并分别对破波带内的爬坡区、内破波区和沙坝区3个区域实验结果进行讨论。 相似文献
5.
深水防波堤周围流场存在复杂的紊动变化,防波堤较容易发生失效破坏。本文利用PIV技术,基于模型实验,对规则波作用下防波堤周围的速度流场及其涡流特性进行了实验研究,获得了规则波流场的瞬时速度分布。通过对不同型式防波堤在不同的水力条件下的波浪流场实验数据的分析,定量地研究了防波堤堤身水域的涡旋流场的水力特性。 相似文献
6.
用60个波高仪组成2m×2m的方阵,同步测量波面过程,用Doppler声学流速仪获得了二维正向和斜向规则波、二维正向和斜向随机波以及三维随机波浪场中不同水深处的同步Euler水质点速度各方向分量的高精度的时间过程资料.以此为出发点,讨论了分段式造波机生成波浪的周期分布特征,发现三维随机波浪周期分布的μ值与二维随机波浪比较有明显增大的趋势.分别从速度合矢量方向与波向的吻合程度(对二维波浪)、"多点波面"组合与"波面-水质点速度"组合两种方式得到方向谱的吻合程度(对三维随机波浪)等不同角度,论证了分段式造波机产生的波浪的内外部结构的一致性. 相似文献
7.
针对海床基回收过程中波浪对回收绳索的冲击响应问题,通过对回收船—回收绳体系的运动响应进行数值模拟仿真,模拟回收绳索的松弛—张紧动态响应过程,分析波浪周期性作用对回收绳索冲击张力的影响。研究结果表明,冲击张力与波高成线性关系且不同周期条件下冲击张力随波高增加量差异较大,冲击张力对波浪周期的响应极为敏感,长周期波浪冲击响应较小,而短周期波浪冲击响应较大,易超出回收绳索的极限负荷,特别是当波长达到船长两倍左右时冲击张力达到最大;随着水深增加,冲击张力呈指数衰减,因此在浅水区波浪周期性作用对海床基的回收影响更大。 相似文献
8.
9.
沈剑平 《山东海洋学院学报》1985,(C00):186-187
本文从椭圆摆线波理论出发，用时间变量的概念，推导出波浪水质点运动速度公式。证明了浪波水质点运动不对称性的存在，即存在着正向与反向水平运动速度的不对称和正向速度与反向速度在作用时间上的不对称。结合泥沙在斜坡情况下的起动流速公式，导出了泥沙在波浪作用下的移动总速度公式。进而讨论了泥沙的输沙率问题，得出一波浪作用下泥沙横向输沙率的近似公式， 相似文献
10.
波流调制效应是指海面非均匀流场产生的挤压和拉伸,进而导致海面局部小尺度波浪谱发生增强或削弱的效应,它是内波、海底地形、海洋锋面等多种海洋现象能被SAR等微波遥感手段观测到的重要物理机制。波流调制效应非常复杂,与海面风速、波浪谱、流场等因素都有关系,直接在海面上开展精确的实验测量非常困难,且重复性差,而在水槽内可以实现较为精确的测量和重复性。本文给出了在水槽实验室内基于线阵CCD同步获取水面波浪谱和流场的测量方法,克服了传统的传感器无法同步获取波浪谱和水面流场的缺点,并在分层流水槽内对孤立内波产生的非均匀流场的波流调制效应进行了观测。研究结果表明基于线阵CCD的测量方法是研究波流调制效应的有效手段,尤其适合对厘米/毫米波段小尺度波浪谱的波流调制效应的研究。此外,在波长小于3cm时波流调制模型的松弛率与经典模型的预测结果有较大出入,需要进一步深入研究。 相似文献
11.
通过自由落体的入水方式,分别在静水和规则波中开展了两种不同横剖面的曲面楔形体入水砰击问题试验研究。使用高速摄像系统记录楔形体入水过程流场演变和运动特性,采用加速度传感器和压力传感器进行数据的动态采集。试验结果表明,在静水中入水时,外凸剖面楔形体入水砰击后模型两侧的射流飞溅比反曲剖面更剧烈,而在楔形体前端的水面以下部分形成的气腔更小;在规则波中入水时,对于相同模型,在波峰和上跨零点相位下模型入水砰击后两侧的射流飞溅比在波谷相位更剧烈。相同工况时,反曲剖面模型所受砰击的加速度峰值和压力峰值更小;在相同的入水速度下,对于相同模型,波浪载荷和砰击载荷的共同作用会使模型所受砰击压力显著增大。 相似文献
12.
Experimental Investigation of Instantaneous Properties of Wave Slamming on the Plate 总被引：1，自引：0，他引：1
The purpose of this paper is to investigate the instantaneous properties of wave slamming on the plate structure of an open structure.The advanced instantaneous measuring technique-Particle Image Velocimetry(PIV) is applied to acquire the instantaneous velocity field of wave slamming.From the cross-correlation analysis results of the images captured by the CCD camera,the flow fields of wave impacting on the structure are displayed visually,and the instantaneous whole-field fluid velocity vectors are obtained.The relation between the instantaneous peak impacting pressures and the instantaneous velocities of water particles is studied by probability analysis. 相似文献
13.
Aimed at the hydrodynamic response for marine structures slamming into water, based on the mechanism analysis to the slamming process, and by combining 3D N?S equation and turbulent kinetic equation with structure fully 6DOF motion equation, a mathematical model for the wind-fluid-solid interaction is established in 3D marine structure slamming wave at free poses and wind-wave-flow complex environments. Compared with the results of physical model test, the numerical results from the slamming wave well correspond with the experimental results. Through the mathematical model, the wave-making issue of 3D marine structure at initial pose falls into water in different complex wind, wave and flow environments is investigated. The research results show that various kinds of natural factors and structure initial poses have different influence on the slamming wave, and there is an obvious rule in this process. 相似文献
14.
A combined wind and wave energy converter concept, named STC concept was proposed. Model tests were performed in terms of operational and survival modes. Water entry and exit phenomena as well as green water on deck were observed during the survivability model tests. In this paper, a nonlinear numerical model based on a blended station-keeping potential-flow solver with a local impact solution for bottom slamming events and an approximated model for the water shipped on the deck is proposed to simulate these nonlinear phenomena. Physical investigation of the water entry and exit process was firstly carried out and uncertainty analysis of the model test results were performed. Numerical comparisons between the nonlinear solver and model test results are then performed in terms of mean, wave frequency and double wave frequency motion response components. The slamming and green water involved in the water entry process are specially investigated, in terms of the physical evolution and the effects on the dynamic motion responses. The validation work on the occurrence of slamming and water on deck as well as the slamming pressure are performed. 相似文献
15.
支撑刚度对水平板波浪冲击压力影响 总被引：1，自引：1，他引：0
上部结构位于浪溅区及由弹性桩腿支撑的海洋结构物,如海上栈桥和海洋平台等,在恶劣海况下会受到强烈的波浪冲击作用并产生振动响应。通过物理模型实验研究了波浪对三种不同支撑刚度的结构物冲击作用。分析了不同支撑刚度结构物底面冲击压力和冲击力的变化特性。讨论了支撑刚度对结构波浪冲击力的影响,给出了冲击压力和冲击力随相对净空(s/H)和相对板长(B/L)的变化规律。实验分析结果表明:水平板底面波浪冲击压力与冲击力均随弹性支撑刚度K的增大而增大;随相对净空(s/H)的增大先增大后减小;随相对板长(B/L)的增大而减小。 相似文献
16.
The vertical water entry of asymmetric two-dimensional bodies with flow separation is considered. As long as there is no flow separation, linearised Wagner's theory combined with the modified Logvinovich model has been shown to provide computationally fast and reliable estimates of slamming loads during water entry. Tassin et al. [11] introduced the fictitious body continuation (FBC) concept as a way to extend the use of Wagner's model to separated flow configurations, but they only considered symmetric bodies. In the present study, we investigate the ability of the FBC concept to provide accurate estimates of slamming loads for asymmetric bodies. In this case, flow separation may not occur simultaneously on both sides of the body. During an intermediate phase, slamming loads are governed by a competition between the local drop in pressure due to partial flow separation and the ongoing expansion of the wetted area. As a first benchmark for the model, we consider the water entry of an inclined flat plate and compare the FBC estimates with the results of a nonlinear model. Then, we consider the case of a foil and compare the FBC results with computational fluid dynamics predictions. In both cases, we find that the FBC model is able to provide reliable estimates of the slamming loads. 相似文献
17.
Slamming on bracings of column stabilized units shall be considered as a possible limiting criterion under transit condition based on the requirements in DNV-OS-C103. However, the wave slamming loads under survival condition were ignored for the strength analysis of the brace structures in many semi-submersible projects. In this paper, a method of strength analysis of brace structure is proposed based on the reconstruction and extrapolation of numerical model. The full-scale mooring system, the wind, wave and current loads can be considered simultaneously. Firstly, the model tests of the semi-submersible platform in wind tunnel and wave tanker have been carried out. Secondly, the numerical models of the platform are reconstructed and extrapolated based on the results of model tests. Then, a nonlinear numerical analysis has been conducted to study the wave slamming load on brace in semi-submersible platform through the reconstructed and extrapolated numerical model. For the randomness of wave load, ten subcases under each condition have been carried out. The value of the 90% Gumble distribution values of the ten subcases are used. Finally, the strength on brace structure has been analyzed considering the wave slamming. The wave slamming loads have been compared between the survival condition and transit condition with the method. The results indicate that wave slamming under survival condition is more critical than that under transit condition. Meanwhile, the wave slamming is significant to the structural strength of the brace. It should be overall considered in the strength analysis of the brace structure. 相似文献
18.
The water entry of large diameter cylindrical structure is studied by applying numerical simulation method. The processes of different diameter cyhndrical structures impacting water with various constant velocities are calculated numerically. Thereafter, analyzed are the distribution of slamming pressure on structure during slamming course and the influence of slamming velocity and cylindrical diameter on slamming process. Furthermore, presented herein is an equation being used to forecast the peak slamming force on a large diameter cylindrical structure. 相似文献
19.
波浪对透空式结构物冲击作用的光滑粒子流体动力学数值模拟 总被引：3，自引：0，他引：3
基于光滑粒子流体动力学(SPH)方法的二维数值波浪水槽模拟了规则波对透空式结构物的冲击作用。通过黎曼解和CSPM相结合的方法对连续方程和动量方程进行了修正。对造波边界采用虚粒子法模拟。提出了一种耦合计算方法来消除造波边界附近的压力波动现象,在结构物边界处设置了适合的冲击边界条件。应用修正的SPH模型模拟了规则波对浪溅区结构物的冲击作用,给出了结构物附近流场和压力场的变化特征,并应用物理模型试验结果对数值模型进行了验证。 相似文献
20.
多筒型导管架基础下放安装过程筒顶开口,筒内气—水自由置换,浪溅区下放过程由于浮力、冲击载荷、附加质量、阻尼效应等因素影响具有很强的非线性。开展模型试验研究波浪荷载下外界控制因素对四筒导管架基础下放过程气垫响应、基础运动和吊缆张力响应的影响机理,探究气垫结构对基础下放过程附加质量和固有周期的影响。结果表明：初始下放过程,筒内气体积聚,气垫压力非线性增长,随着下放深度增大,气垫压力趋于稳定;气垫压力响应趋势与基础下放速度和开孔率相关,波浪荷载仅影响气垫响应幅值;筒型基础下放穿越浪溅区阶段受到砰击荷载作用,气垫结构对砰击荷载产生缓冲效果;考虑气垫—水柱耦合作用时,顶盖即将入水阶段,气弹簧和水弹簧耦合作用下整体刚度增大,基础固有周期出现减小趋势。 相似文献