共查询到20条相似文献，搜索用时 156 毫秒
1.
在对挡墙加固边坡进行设计和评价时应综合考虑基质吸力和挡墙对边坡整体稳定性的影响。应用可以考虑基质吸力的弹塑性强度折减有限元程序,分析了挡墙加固非饱和土边坡的整体稳定性,揭示了基质吸力对加固边坡整体稳定性的影响程度,同时亦分析了整体潜在滑动面位置的变化情况,并进行了关于吸力摩擦角的敏感性分析。 相似文献
2.
This study examines the effect of loss of apparent cohesion from rainwater infiltration upon the stability of partly saturated, allophanic soil slopes of Dominica (West Indies). The parent material of the Dominican allophanic soils are the andesitic and dacitic volcanic rocks from ten volcanic centres of mainly Pleistocene age. Although simplifying assumptions are made to assess the depth of wetting front and magnitudes of true and apparent cohesion values of the partly saturated allophanic soils, certain inferences of practical significance emerge from the study. Matric suction contributes to the effective stress of unsaturated soils and increases the shear strength of these soils by imparting them an apparent cohesion strength component. This apparent cohesion strength component of the partly saturated Dominician allophanic soils is considered to be related to the matric suction term (ua−uw) by a parabolic relationship. The partly saturated allophanic soil slopes of Dominica would invariably fail from loss of apparent cohesion upon saturation of the soil mantle by the infiltrating water front only if (a) the average slope angle (β) is greater than or equal to the drained shear strength parameter of the unsaturated soil (Φd) (slopes with β ≥ Φd are referred to as category 1 slopes in this study) and (b) the drained cohesion parameter (cd) belonging to the partly saturated soil of the category 1 slope is mainly contributed by matric suction induced apparent cohesion (capp) and contribution from true cohesion (c′) is absent. However, the possibility of the category 1 slopes (for the case 1 situation) failing in the saturated condition from effective stress reduction due to rise in ground water table is shown to be an unfeasible proposition. In contrast, for the case 1 situation, the partly saturated category 2 slopes (β < Φd) are insusceptible to failure from reduction in effective stress due to loss of matric suction but fail in the saturated condition from effective stress reduction due to rise in ground water table. If the allophanic soils were to possess a sufficient magnitude of true cohesion (c′), even the partly saturated category 1 slopes possessing slope angles (β) much in excess of their Φd values (β − Φd = 15.1°) would remain stable upon total elimination of the matric suction induced cohesion. However, partly saturated category 1 slopes possessing a true cohesion component and insusceptible to failure from reduction in effective stress upon loss of matric suction, invariably fail in the saturated condition from reduction in effective stress due to rise in ground water table. Using the methodology developed in this study, two previously reported case histories pertaining to rain induced translational landslides in the residual soil areas of Brazil are re-examined and the results obtained in this study are found to be in agreement with the findings of the previous researchers. 相似文献
3.
给出了均质土坝的下游坝坡的安全系数的计算方法。均质土坝的下游坝坡有可能会通过滑裂面发生破坏。土坝中的土坡通常处于非饱和状态。非饱和土坡的安全系数计算需要考虑吸力对抗剪强度的贡献以及土坡中的非饱和渗流。给出处于饱和-非饱和渗流状态下的土坡的安全系数,有助于评价均质土坝的安全系数。下游坝坡的安全系数计算方法有：极限平衡法、上限解法和下限解法,该算法适用于非饱和土坡,且是在饱和土坡安全系数的计算方法上修正得到的。算例中非饱和土坡安全系数的计算考虑了吸力对抗剪强度的贡献。考虑非饱和渗流理论的土坡安全系数计算方法通常更加接近现场实际情况,并且对于同一坝坡,考虑非饱和渗流计算出的土坡安全系数要比饱和渗流理论计算出的安全系数大。 相似文献
4.
Most classical approaches for evaluating the stability of soil slopes with cracks are performed under two-dimensional (2D) condition. Three-dimensional (3D) effect and suction-induced effect of unsaturated soils are generally neglected in assessing the slope stability. This paper develops a 3D limit analysis method to evaluate the stability of an unsaturated soil slope with tension cracks under steady infiltrations. The boundary-value problem is formulated based on the 3D rotational failure mechanism by taking the effects of suction, effective unit weight, and tension crack into account. A simplified method is proposed to calculate the work rate of unsaturated soil weight. A layer-wise summation method is developed based on the divergence theorem to calculate the internal energy dissipation rate. Detailed discussions are conducted to investigate the effects of suction and Poisson's ratio on the stability of unsaturated soil slopes. Examples are given to illustrate the 3D effect, the suction-induced effect as well as the effects of infiltration and water in cracks on the slope stability. 相似文献
5.
在对非饱和土边坡进行稳定分析时,应该全面地考虑基质吸力对边坡稳定的贡献。首先,分别探讨了基于Fredlund非饱和土强度表达式和Bishop非饱和土有效应力强度公式将强度折减有限元法推广到非饱和土边坡稳定分析中的具体方法;然后,开发了可以考虑基质吸力两种处理方法的强度折减有限元计算程序;最后,给出了一个非饱和土边坡稳定分析的对比算例,说明了二者的不同特点。 相似文献
6.
采用有限元法分析了非饱和均质各向异性土坡中的降雨渗透过程和土水相互作用的变化过程,使用修改的Mohr-Coulomb破坏准则考虑非饱和土的抗剪强度,根据基质吸力变化引起抗破坏强度变化的原理,寻找最危险的滑移面位置,计算最小稳定安全系数,研究了土坡遭受降雨渗透时的安全稳定问题。实例分析结果表明,该法在评判降雨时非饱和土坡的稳定性方面是合理可行的。同时分析数据表明裂隙的存在对土质边坡稳定性的影响是显著的,在对雨水入渗的土边坡稳定性分析时,必须考虑裂隙的影响。 相似文献
7.
讨论了抗滑桩加固边坡的稳定分析研究状况,在全面地考虑基质吸力和抗滑桩对边坡稳定性的贡献后,利用所发展的可考虑基质吸力的弹塑性强度折减有限元程序,探讨了抗滑桩加固前后的非饱和土边坡整体稳定性,并且与相应不考虑基质吸力条件下的边坡稳定性进行了对比分析。 相似文献
8.
降雨及浸水往往引起天然土坡及人工土坡的滑坡,其中,土中基质吸力的消失是一个重要原因。通过试验和计算分析,揭示了基质吸力对边坡稳定所起的重要作用。非饱和土边坡稳定计算中的关键参数 的确定,尚有待于进一步研究。 相似文献
9.
在边坡稳定性研究中,吸力的影响经常被忽略。基于非饱和土的渗流理论,利用数值分析方法研究了一个由于连续降雨导致的非饱和土边坡失稳的工程实例。研究结果表明:非饱和土的吸力对于维持边坡稳定具有重要影响,而吸力与降雨频率、降雨量、降雨时间、蒸发量等密切相关。对于工程实践而言,吸力的监测对于维持土坡稳定具有重要意义。 相似文献
10.
对部分应用土-水特征曲线来预测非饱和土抗剪强度的公式进行了归纳分析。应用压力板仪与非饱和三轴仪,测试了荆门原状弱膨胀土的土-水特征曲线和控制吸力的非饱和三轴抗剪强度参数,并将试验结果与各抗剪强度公式的预测值进行对比,分析了各强度公式的局限性。试验结果表明,非饱和原状膨胀土的净法向应力摩擦角随着吸力的不同而变化,根据双应力变量理论确定的吸力对强度的贡献与围压有关,不同围压下吸力对强度的贡献不同,表观凝聚力 与吸力间符合乘幂函数关系。 相似文献
11.
研究可以同时考虑渗流、变形与稳定的非饱和土质边坡稳定性分析方法具有重要的理论意义及工程实用价值。基于Fredlund双应力变量理论进行非饱和非稳定渗流-应力耦合分析,同时与传统非耦合渗流方法确定的孔压场进行对比发现,两种方法确定的浸润线变化过程相近,堤底处孔压的最大相对误差为8.8%,验证了耦合分析结果的可靠性。将基质吸力对强度的贡献纳入黏聚力中得到坡体强度参数的空间分布规律,又基于滑面强度参数时空分布规律借助Matlab平台开发了非稳定渗流条件下非饱和土质边坡稳定性的矢量和法分析程序。以库水位下降条件下堤坡的稳定性分析为例,将不同方法的计算结果进行对比,发现文中方法搜索得到的滑面位置相对于传统方法要深缓,但总体位置相差不大,不同方法对应的安全系数相差不足0.096,验证了所提方法的合理性。 相似文献
12.
针对降雨入渗土坡的稳定问题,建立一个考虑水力渗透系数特征曲线、土-水特征曲线以及修正的Mohr-Coulomb破坏准则的非饱和土流固耦合有限元计算模型,进行雨水入渗下非饱和土边坡渗流场和应力场耦合的数值模拟,得到非饱和土边坡变形与应力的若干重要规律。研究成果为降雨入渗条件下非饱和土边坡的稳定分析提供了基础。 相似文献
13.
非饱和土应力状态是采用有效应力( –ua)和基质吸力(ua–uw)作为应力状态变量,相应的Mohr-Coulomb破坏包面是在有效应力、基质吸力和剪应力的三维坐标系中的曲面（通常在应用中假定为平面）。根据应变等效性原理定义损伤变量,由非饱和土给出损伤变量与偏应力的曲线,并得到非饱和土的损伤阈值与基质吸力呈指数函数关系。采用一非饱和土土坡开挖过程的算例,说明基于损伤演化描述的稳定性数值分析方法可行。 相似文献
14.
INTRODUCTION Theinfiltrationandevaporationofwaterinasoil slopeareofparamountimportanceindetermining slopestability.Previousengineeringcasesandstud ieshaveshownthatrainwaterisoftenamajorfactor intheslopefailureofexpansivesoils.Expansivesoils intropicalandsubtropicalzonesareoftenunsaturat ed,andsoilslopesareinastablestateinnormalcli mateconditionsbecauseofthehighsuctionandshear strengthofthesoilmass.However,oncepermeation happensrainwaterwillinfiltrateintothesoilmasswhichleadstoanincreasein… 相似文献
15.
Summary A procedure for the stability analysis and design of geosynthetic reinforced soil slopes over a firm foundation is described. Firstly the unreinforced slope is analysed, and for this a circular failure method is used which allows a surcharge load to be taken into account. Any method of slip circle analysis could be used to identify the coordinates of the centre of the slip circle, its radius and the minimum factor of safety. In this study, both internal and external stability analysis of the reinforced slope is presented. Internal stability deals with the resistance to pullout failure within the reinforced soil zone resulting from the soil/reinforcement interaction. The external stability is considered by an extension of the bilinear wedge method which allows a slip plane to propagate horizontally along a reinforcing sheet. The results for total tensile force, internal and external stability are presented in the form of charts.For given properties of soil and slope geometry, the required strength of the geosynthetic and the length of reinforcement at the top and bottom of the slope can be determined using these charts. The results are compared with the published design charts by Schmertmann et al. (1987). 相似文献
16.
This paper presents an elasto‐plastic model for unsaturated compacted soils and experimental results obtained from a series of suction‐controlled triaxial tests on unsaturated compacted clay with different initial densities. The initial density dependency of the compacted soil behaviour is modelled by establishing experimental relationships between the initial density and the corresponding yield stress and thereby between the initial density and the location and slope of normal compression line. The model is generalized to three‐dimensional stress states by assuming that the shapes of the failure surface and the yield surface in the deviatoric plane are given by the extended SMP criterion. A considerable number of the isotropic compression, triaxial compression and extension tests on unsaturated compacted clay with different initial densities were performed using a suction‐controllable triaxial apparatus, to measure the stress–strain–volume change in different stress paths and wetting paths. The model has well‐predicting capabilities to reproduce the mechanical behaviour of specimens compacted under different conditions not only in isotropic compression but also in triaxial compression and triaxial extension. Copyright © 2003 John Wiley & Sons, Ltd. 相似文献
17.
为了模拟实际工程中黄土在不排水条件下的破坏,在控制含水率不变条件下,利用非饱和土真三轴仪对不同初始吸力非饱和原状黄土进行了等向固结试验和不同中主应力参数b值的剪切试验,研究了非饱和原状黄土的力学特性。研究结果表明：真三轴等向压缩屈服应力随着初始吸力的增大而增大,吸力随着净平均应力的增大而减小,净平均应力对吸力的影响程度随着初始吸力的增大而增大。不同 值条件下,广义剪应力和净平均应力破坏状态线近似呈平行直线关系,广义剪应力和有效净平均球应力试验点可归一为饱和土的排水剪切破坏状态线;剪切破坏时吸力随着b值的增大基本呈线性增大趋势;孔隙比和净平均应力对数临界状态线近似呈线性平行关系,其斜率比饱和土大,且大于等向压缩屈服前的斜率;非饱和土孔隙比和有效净平均球应力对数临界状态线与饱和土的临界状态线近似呈线性平行关系;不同净围压条件下,不同 值非饱和土与饱和土的破坏状态孔隙比的比值与气体饱和度的试验点分布于1.0～1.2的直线带内,但同一净有效球应力条件下可以归一为一条非线性曲线。 相似文献
18.
Bishop和Fredlund的非饱和土强度公式参数不易工程应用,文中基于双曲线的非饱和土强度公式,采用简化Bishop法建立非饱和土边坡的稳定方程,分析膨胀土边坡的稳定性,讨论了吸力、分层及其边坡表层裂隙对非饱和膨胀土边坡稳定性的影响。通过分析与比较,揭示了膨胀土边坡浅层滑坡的原因。 相似文献
19.
进行了不同坡度土钉加固边坡坡顶加载的离心模型试验,观测了土坡的破坏过程并测量土坡的位移场,研究了土钉加固黏性土坡的承载力、变形和破坏规律以及坡角对其破坏规律的影响。试验结果表明,坡顶荷载的增加引起土坡变形的增加,变形的集中产生和发展导致滑裂面的形成并使土坡发生破坏。土钉变形规律受加载阶段和加载底板的综合影响,坡顶荷载越大,接近坡顶的土钉弯曲挠度越大,钉土间的相互作用越强。土坡的坡角越大,承载力越低,土体呈现出更显著的向坡面位移的趋势。 相似文献
20.
Simple limit equilibrium analyses can be performed to determine the Factor of Safety (FOS) against slope failure of unsaturated
soil slopes. However, many of the input parameters needed for these analyses are highly variable, and the FOS value obtained
is critically dependent on assumptions made by the designer. This paper describes a suite of reliability analyses on unsaturated
soil slopes performed using an invariant reliability model. The results are presented in design charts from which a designer
can choose the FOS value required to ensure a given target reliability index for a slope. The approach ensures that despite
the variability of input parameters the slope will have a probability of failure of 2.23% or less. 相似文献
|
