共查询到20条相似文献，搜索用时 168 毫秒
1.
抽水试验中,动水位数据采集记录及处理分析对水文地质参数计算具有重要意义。近年来自动水位计被广泛用于抽水试验,通过传感器压强水头变化值获取水位降深。因井管内水流动会产生水头损失,自动水位计安放位置不同会导致获取的井水位降深不同,不同于传统方法测得的井水面降深,对水文地质参数计算将产生一定影响,因此如何合理放置自动水位计以及在参数计算中如何应用其获取的水位降深都亟待开展试验研究。在黑河流域第四系大厚度含水层地区,选择典型单层试验孔和利用分层封隔技术实现的一孔同径多层抽水孔开展试验研究,在动水位以下抽水试验层段上部、中部、下部以及潜水泵上部和下部分别放置自动水位计进行了系统的数据采集分析。结果表明:抽水试验中因井管内水流沿程水头损失及速度水头差异导致不同位置自动水位计获得压强水头变化值不同,本次试验实测到井筒内不同部位井损值;井损值在潜水泵进水口处最大,随距潜水泵距离的增大而减小,为避开井筒内较大水头损失对参数计算的影响,自动水位计宜优选安放在潜水泵上部接近动水位位置;在单孔抽水试验中利用稳定流公式计算水文地质参数时,自动水位计获取水位降深含井损不可忽略,需通过多落程抽水试验数据分析扣除后使用。同时,抽水试验中自动水位计不同位置获取数据的处理分析方法为更好地理解井中水头损失提供了依据。 相似文献
2.
通过分析抽水试验过程中井损产生的原因及确定方法,运用水位动态变化过程中的井损计算方法,对乌兰陶勒盖水源地WL6号孔的抽水试验资料的井损计算程序进行了说明,并提出了该水源地理想降深与实际降深的经验公式。利用Aqui Test软件,分别计算了忽略井损和考虑井损两种情况下潜水(承压水)抽水井渗透系数及给水度(贮水率),从计算结果来看,计算井损、修正降深所得的各参数的值要比不考虑井损的值大;井损对潜水的抽水试验资料的影响要比承压水的大。 相似文献
3.
针对传统施工程序无法解决坚硬岩石止水环隙很小（仅3 mm）钻孔的同径止水及分层抽水试验问题,以山西某水文地质参数井为研究对象,采用现场和室内综合试验的方法,对同径止水方案、材料、技术、分层抽水等工艺进行研究。结果表明:（1） 同径止水装置经过特殊的“外掏内缩”设计与制作,使止水外环间隙由3 mm增大到8.5 mm,解决了“极小止水环隙”下的同径止水问题;经抽水检验,止水效果良好。（2） 在孔外一系列试验的基础上,定制的止水材料和选择的止水组合与本孔的适应性强,下管风险小,实施过程相当顺利。（3）专门设计的分层导水管路,其上串接的隔离封水胶球与止水套管柱内设置的锥形隔水接头相互契合,封水可靠,形成了两套独立的导水管路,满足了上、下含水层分层抽水试验的工况。研究结果可为类似水文地质参数井开展同径止水或分层抽水试验研究提供参考。 相似文献
4.
天津地区部分深层地下热水钻井在开采过程中井口水温明显高于开采前的井口水温,井内水的密度随之降低,可导致动水位高于开采前的静水位。采取井底压力的折算公式和室内实验的方式分别对实测数据和该现象进行分析、模拟。结果表明,开采条件下的井底压力明显小于停采条件下的井底压力,水位拟合主要受地热井的密度、井底压力的计算公式和计算方法、地质结构以及地热井回灌等因素的影响;在实验第一阶段观测到井底温度与井口水位呈正线性相关,井底压力与水柱的平均密度呈线性负相关;在第三阶段平均密度和井底压力也呈线性负相关;而在第二阶段井底压力几乎保持不变时,可以根据该压力对不同井口温度时动水位升高值进行预测。 相似文献
5.
6.
The origin and movement of groundwater are the fundamental questions that address both the temporal and spatial aspects of ground water run and water supply related issues in hydrological systems. As groundwater flows through an aquifer, its composition and temperature may variation dependent on the aquifer condition through which it flows. Thus, hydrologic investigations can also provide useful information about the subsurface geology of a region. But because such studies investigate processes that follow under the Earth's shallow, obtaining the information necessary to answer these questions is not continuously easy. Springs, which discharge groundwater table directly, afford to study subsurface hydrogeological processes.The present study of estimation of aquifer factors such as transmissivity (T) and storativity (S) are vital for the evaluation of groundwater resources. There are several methods to estimate the accurate aquifer parameters (i.e. hydrograph analysis, pumping test, etc.). In initial days, these parameters are projected either by means of in-situ test or execution test on aquifer well samples carried in the laboratory. The simultaneous information on the hydraulic behavior of the well (borehole) that provides on this method, the reservoir and the reservoir boundaries, are important for efficient aquifer and well data management and analysis. The most common in-situ test is pumping test performed on wells, which involves the measurement of the fall and increase of groundwater level with respect to time. The alteration in groundwater level (drawdown/recovery) is caused due to pumping of water from the well. Theis (1935) was first to propose method to evaluate aquifer parameters from the pumping test on a bore well in a confined aquifer. It is essential to know the transmissivity (T = Kb, where b is the aquifer thickness; pumping flow rate, Q = TW (dh/dl) flow through an aquifer) and storativity (confined aquifer: S = bSs, unconfined: S = Sy), for the characterization of the aquifer parameters in an unknown area so as to predict the rate of drawdown of the groundwater table/potentiometric surface throughout the pumping test of an aquifer. The determination of aquifer's parameters is an important basis for groundwater resources evaluation, numerical simulation, development and protection as well as scientific management. For determining aquifer's parameters, pumping test is a main method. A case study shows that these techniques have been fast speed and high correctness. The results of parameter's determination are optimized so that it has important applied value for scientific research and geology engineering preparation. 相似文献
7.
本文通过对黄土地区潜水含水层深井进行现场单井多落程抽水试验和双井抽水试验资料的整理分析,得到黄土潜水含水层深井抽水井流的一般规律,同时对水跃值的变化规律进行分析. 相似文献
8.
以单井抽水试验资料为基础,计算出该区的新近系砂砾岩含水层的出水量为40m^3/h。为解决水源热泵系统的热源及同层回灌问题,进行了较长时间的带有观测孔的抽水试验及回灌试验。试验表明：该区的渗透系数为32.16m/d,影响半径为166m,回灌渗透系数为14.38m/d,回灌影响半径为61m。据此计算干扰井单井抽水量为38.51m^3/h,干扰井单井回水量为11.14m^3/h,同时确定该区的抽灌井比例为1∶4。根据用水需求,该区设计抽水两口,回灌井8口,备用一口回灌井,形成该区的水源热泵系统。系统运行近两年来,单井出水量、回灌量及水位降深均符合设计要求,达到了预期效果。 相似文献
9.
利用设计建造的抽水试验装置,采取多项潜水及承压水的抽水试验,获得大量的抽水井周围饱水介质场三维动态观测数据。试验发现：无论是潜水还是承压水状态,抽水井附近观测井的水位变化,均具有距抽水井愈远愈高、愈近愈低的漏斗状分布,抽水井附件的地下水位降落漏斗是显著的;同时发现每个观测井不同高度上的观测点的水位,均呈现上高下低的特征,说明地下水具有由上到下的运动分量,地下水由周边的供水边界向抽水井聚集运移时,运动方向是下斜向的,潜水如此,承压水也如此。分析认为,这是水头压力与水体自身重力同时起作用的结果。由此推断,在抽水时,靠近承压水含水层顶板存在强势水流,且越靠近补给源,这种强势水流越强。 相似文献
10.
本文对新疆伊犁盆地库捷尔太铀矿床抽水试验及参数计算方法做了较为详细的对比分析，总结出适合于可地浸砂岩型铀矿床不同工作阶段求取 含水层渗透系数的抽水试验方法；阐述了在自喷井中用扬水试验求取含水层渗透系数方法的可行性及其在实际应用时应注意的问题；提出利用数量固定不可调的深井泵进行变流量抽水以控制不同的降深，解决了多年来因空气压缩机性能所限难以进行长时间抽水的问题，并对抽水试验的延续时间、降深次数以及降深等参数提出了具体建议。 相似文献
11.
Groundwater withdrawal impacts in a karst area 总被引：1，自引：0，他引：1
During a 3000-gpm pump test on a groundwater supply well in Augusta County, Virginia, residential properties were impacted. The impacts included lowered farm pond water levels, development of a sinkhole, and water level decrease in residential wells. A study was performed to assess whether a lower design yield was possible with minimal impacts on adjacent property. This study included a 48-h 1500-gpm pump test that evaluated impacts due to: (1) sinkhole development and potential damage to homes, (2) loss of water in residential wells, and (3) water-quality degradation. Spring flows, residential well levels, survey monuments, and water quality were monitored. Groundwater and surface water testing included inorganic water-quality parameters and microbiological parameters. The latter included particulate analyses,Giardia cysts, and coliforms, which were used to evaluate the connection between groundwater and local surface waterbodies. Although results of the study indicated a low potential for structural damage due to future sinkhole activity, it showed that the water quality of some residential wells might be degraded. Because particulate analyses confirmed that groundwater into the supply well is under the direct influence of surface water, it was recommended that certain residents be placed on an alternate water supply prior to production pumping and that filtration be provided for the well in accordance with the Surface Water Treatment Rule. A mitigation plan was implemented. This plan included crack surveys, a long-term settlement station monitoring program, and limitation of the groundwater withdrawal rate to 1.0 million gallons per day (mgd) and maximum production rate to 1500 gpm. 相似文献
12.
垃圾填埋场抽水试验及降水方案设计 总被引：2，自引：0，他引：2
垃圾填埋场中的渗滤液水位过高会引发一系列环境和稳定问题,工程上可用竖井抽水降低渗滤液水位。通过在填埋场现场进行抽水试验,确定垃圾土的渗透系数和抽水影响半径,在此基础上对填埋场降水的瞬态流问题进行有限元模拟,分析了抽水井口径和间距对填埋场降水的影响,提出了降水方案的设计步骤和方法。抽水试验表明,现场垃圾的渗透系数约为3.6×10-4cm/s,抽水影响半径约为20m。数值分析表明,井径的变化对于降水效果影响不大,而合理选择抽水井间距对降水十分关键。进行抽水方案设计时,应首先根据工期和降水幅度要求计算井间距,按井的出水速度选择水泵,再根据水泵确定井径,最后根据井径和过滤层形式确定钻孔尺寸并选择钻机。 相似文献
13.
为掌握绥芬河市北寒葱河河谷地下水的水质状况,向地方提供合理的水资源开发建议,本研究以地质、水文地质调查、水样采集等手段为基础,利用模糊综合评价法和层级阶梯法分别进行了研究区地下水水质和污染状况评价,应用物探测试、抽水试验等原位测试技术论证了区域地下水的富水性。以上工作基本查明了研究区地下水的水量和水质现状.认为研究区裂隙承压水一般为Ⅰ~Ⅲ类水质,污染等级为未污染水,水质状况较好,污染程度较低,宜于饮用;中生代构造破碎带涌水量可达350m3·d-1以上,建议地方政府应重点围绕构造破碎带开展物探找水,并开展地下水源地分区保护规划. 相似文献
14.
15.
16.
单井稳定流抽水试验中水位恢复曲线的作用分析 总被引：1，自引：0，他引：1
单井稳定流抽水试验是目前煤炭勘探中获取水文地质参数、查明水文地质条件的主要方法之一。由于其获取的水文地质参数相对于非稳定流抽水试验简单直接而被广泛应用,但所计算的含水层渗透系数比实际往往偏小,且易忽视对水位恢复资料的分析研究与利用。通过对安徽淮南、淮北煤田近10年来水文地质勘探单孔稳定流抽水试验资料的分析与研究,论述了单井稳定流抽水参数计算的过程和存在的不足,强调了绘制水位恢复曲线的作用,提出了单井稳定流抽水渗透系数计算结果的采用方法和建议。进而使井田水文地质条件评价、矿井涌水量预测更加客观、真实。 相似文献
17.
18.
封隔注浆分层成井技术为多层水文地质钻孔分层成井提供了一种快速高效的新工艺。传统分层成井方法耗时长、效果差、止水效果不稳定,尤其是在细颗粒或钻孔结构不稳定的地层分层成井困难,易发生钻孔事故等问题。文章通过室内试验和野外施工,探索出封隔注浆分层成井。以HQ56水文地质孔为例,研究了分层成井、分段振荡洗井,并进行了分层抽水试验。研究表明,封隔注浆分层成井技术止水可靠,分层抽水试验数据准确。该技术尤其适用于细颗粒或钻孔结构不稳定地层快速分层成井。 相似文献
19.
为准确获取原状Q3黄土的竖向和水平饱和渗透系数,进行了原位、室内试验测试以及数值模拟反演,并应用大型试坑浸水试验检验了所获饱和渗透系数的可靠性。进行了不同内径尺寸的原位双环入渗试验,获取了竖向饱和渗透系数,并应用室内试验测试了竖向和水平饱和渗透系数以及持水曲线;应用COMSOL软件对双环入渗试验进行数值模拟,检验了所测饱和渗透系数的可靠性,利用正交试验获得了最优的竖向和水平饱和渗透系数取值,并利用反演结果对试坑进行数值模拟,将其水分入渗情况与实测值对比。研究结果表明：在现场进行双环入渗试验时选取较大内径的双环获得的竖向饱和渗透系数更为合理。针对双环入渗试验,数值模拟反演所得最优饱和渗透系数在竖向上接近于原位试验所得竖向饱和渗透系数、水平向上接近室内所测水平向饱和渗透系数,竖向饱和渗透系数比水平向饱和渗透系数更加显著地影响水分入渗过程。通过对大型试坑水分入渗情况的验证,检验了反演所得最优饱和渗透系数的可靠性。 相似文献
20.
The main target of this research paper was to the hydrogeological assessment of the groundwater resources to irrigate 600 ha of irrigable agricultural lands, distributed along the Dead Sea–Aqaba Highway in Umm, Methla, Wadi Musa, Qa’ Saideen and Rahma, southern Jordan. Therefore, a comprehensive groundwater study was commenced by drilling eight new wells which can be used to supply irrigable areas with the existing groundwater that would be enriched by the yield of three proposed recharge dams on Wadi Musa, Wadi Abu-Burqa, and Wadi Rahma. The evaluation of the pumping test data of the drilled was carried out using the standard methods of pumping test interpretation. This was based on the available water table measurements at well locations and knowledge of water flow in the general. The sustainable yield of each well was calculated based on the pumping test parameters. The obtained results indicate that pumping out of Beer Mathkor wells should not exceed 1,100 m3/day in the case of continuous pumping and 8,700 m3/day in the case of intermittent pumping. Since the water table did not significantly change with small changes in pumping (it took eightfolds of magnitude increase in pumping from approximately 1,100 to 8,700 m3/day to show a significant drop in the water table equivalent to about 5.5 MCM per year from the aquifer. 相似文献