共查询到20条相似文献，搜索用时 250 毫秒
1.
A three-dimensional (3D) soil–structure interface model is proposed within the two-mechanism constitutive theory and bounding surface theory originally established for soils. The proposed model has two main characteristics: first, the model is formulated based on two different and superposed deformation mechanisms. The first mechanism is due to the stress ratio increment, and the second is due to the normal stress increment. Each mechanism induces a shear strain component and a normal strain component. The proposed model can be reduced to the conventional single-mechanism interface model. Second, the plastic modulus and stress dilatancy are defined using the bounding surface theory. The plastic flow rule under cyclic loading is modified and assumed to be dependent on both the stress state of the mapping point and the stress reversal loading direction. The proposed model was validated against the available 3D interface tests and was found to satisfactorily reflect the salient features of the interfaces under monotonic and cyclic loading paths with different normal boundaries. The problem in which the elastic normal stiffness in conventional single-mechanism interface models is often underestimated to enhance the simulation performance under varying normal stress conditions is solved by incorporating the second mechanism. And the effect of the second mechanism on the modeling behavior is discussed. The modified plastic flow direction accurately simulates the 3D cyclic shear response, and the difference between the model simulation and test result increases with the number of cycles by use of the plastic flow direction defined in conventional bounding surface theory. 相似文献
2.
Soil nailing has been widely used as a reinforcing technique to retain excavations and stabilise slopes. Proper assessment of the interaction between the nails and the surrounding soil is central to safe and economical design of the composite reinforced soil structure. In this note, a new interface model, denoted as “embedded bond-slip model”, is proposed to model the soil–nail interaction numerically in a simplified manner. Combining the key features of the embedded element technique and the conventional interface element method, the proposed plane–strain interface model has the advantages that no special considerations have to be given to the arrangement of the finite element mesh for the soil nails, and that possible tangential slippage along the interface can be modelled. The formulation also allows pore water flow across the soil nails to be incorporated into the analysis. The proposed model has been implemented into a finite element code and verified by simple element tests under different uni-direction loading conditions. Using the proposed interface model, back analyses of a field test involving a soil-nailed cut slope subjected to a rise in groundwater table have been conducted. This note presents the details of the embedded bond-slip model and the numerical results which demonstrate that the proposed model is capable of simulating soil–nail interaction conveniently and realistically. 相似文献
3.
The present study focuses on the hydraulic behaviour of joints, and, specially, on its numerical implementation in terms of the FEM analysis using a discrete fracture flow approach. Fluid flow through discontinuities has traditionally been modelled using special elements of zero-thickness, which we can classify into single, double and triple-nodded. Single node elements are the simplest and consist of ‘line’ or ‘pipe’ elements which are superimposed onto the standard continuum mesh and that can only model the longitudinal conductivity through the discontinuity. On the other hand, some authors have included the influence of a transversal conductivity, and the subsequent localized potential drop, by using triple node interface elements. In those, the two nodes of the adjacent continuum elements represent the potentials in the pore system on each side of the interface, and a third node in the middle represents the average potential of the fluid in the channel represented by the discontinuity. Finally, double node interface elements have also been proposed, which have the advantage of making it possible to use the same FE mesh for both mechanical and flow analysis. In some cases the influence of a transversal conductivity is not considered and, therefore, although geometrically double-nodded, these elements belong to the single node type and when time comes to solve the system the two nodes must have the same potential, which can only be obtained by the ‘trick’ of prescribing the equivalence of these two d.o.f. before solving the global system of equations. This limitation may, however, be avoided by assuming that the potential in the channel is the average of the two sides of the interface. Based in this simple assumption, an alternative flow interface model has been recently developed and implemented, which preserves both longitudinal and transversal conductivities. An application example is developed and solved with the three types of interfaces described. The results offer useful information regarding the range of applicability and limitations of the new double-nodded interface element proposed. Copyright © 2004 John Wiley & Sons, Ltd. 相似文献
4.
An extensive literature on the shear behavior of continuum–particulate interfaces has been developed during the last four decades. However, relatively limited work regarding the behavior of interfaces under different loading conditions has been published. This paper presents a discrete element modeling study, along with comparisons from experimental data, of interface behavior under axial and torsional drained loading conditions. Detailed studies allow for links between micro‐scale particle behavior and observed global response to be developed and for the latter to be evaluated in light of particle–particle and particle–continuum interactions. The results of this study indicate that axial and torsional interface shear induce inherently different loading conditions, as shown by the different failure envelopes, stress paths, and induced soil volume changes and deformations. Furthermore, the results presented in this paper indicate that particle‐level mechanisms, such as particle rotations and contact slippage, play different roles in axial and torsional shear. Coordination number, polar histograms, particle displacements, particle rotations, and local void ratio measurements provide further insights into the fabric evolution, loading conditions, and failure mechanisms induced by these two shear modes. This study expands the current understanding of interface behavior and discusses potential improvements to geotechnical systems that leverage the characteristics of different imposed loading conditions. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
5.
6.
为了揭示新型注浆成型螺纹桩的承载力特性及桩土接触特性,利用二维离散元（DEM）数值分析不同螺纹间距的桩-土接触特性。在既有螺纹桩-土界面的大型直剪试验方案的基础上,建立模拟试验的离散元模型。通过模拟试验的伺服加载机制,实现在接触面法向上施加恒定的压力,然后水平移动接触面底板进行剪切,得到不同螺纹数下剪切位移与剪切应力的关系曲线、孔隙比分布图和力链传力机制。离散元分析表明,存在一个最优的螺纹间距,使接触面的极限抗剪强度最大;螺纹桩桩土接触面周围土体会出现一个拱形的破坏面,该微观机制与室内试验观察一致。 相似文献
7.
The paper considers a plane joint or interface element suitable for implementation into a standard non-linear finite element code. The element is intended to model discontinuities with rough contact surfaces, such as rock joints, where dilatant behaviour is present. Of particular concern is the formulation of a constitutive model which fully caters for all possible histories of opening, closing and sliding (accompained by dilation or contraction) in any direction. The non-linear incremental constitutive equations are formulated in a manner appropriate for a back-ward difference discretization in time along the path of loading. The advantage of such an approach is that no essential distinction need be drawn between opening, closing and sliding. Further, a convenient formulation of the constitutive equations is facilitated by representing the different contact conditions in relative displacement space. The state diagram in relative displacement space, however, changes from one time step to the next, and evolution equations for the updating must be formulated. These concepts are illustrated for two rock-joint models: a sawtooth asperity model and a limited dilation model. The models are based on a penalty formulation to enforce the contact constraints, and explicit equations for the tangent stiffness matrix and for the corrector step of the standard Newton–Raphson iterative algorithm are derived. These equations have been implemented as an user element into the finite element code ABAQUS7. Three examples are presented to illustrate the predictions of the formulation. 相似文献
8.
Open-ended pipe piles are often used in offshore foundations. The response of the soil plug inside a pipe pile is poorly understood, and only limited work has been performed to quantify the response under the different loading conditions relevant to offshore platforms. This paper describes numerical analyses that have been carried out in order to assess the end-bearing capacity of the soil plug under loading conditions which range from undrained to fully drained. The soil plug has been modelled as either elastic, elastic–perfectly-plastic or elastoplastic. The soil–pile interface, an important aspect of the problem, has been examined critically. Comparison with experimental data from model test at laboratory scale indicates that the load–deformation behaviour of the soil plug is modelled well using an elastoplastic model for the soil plug, and an elastic–perfectly-plastic joint element to model the soil–pile interface. The finite element analyses show that, under typical loading conditions, adequate end bearing may be mobilized by the soil plug, largely by high effective stresses in the bottom 3–5 diameters of the soil plug. 相似文献
9.
Michael G. Katona 《国际地质力学数值与分析法杂志》1983,7(3):371-384
A simple friction–contact interface element is introduced which simulates frictional slippage, separation, and re-bonding of two bodies initially mating at a common interface and subsequently deforming with an arbitrary static loading schedule. Constraint equations between initially mating node pairs and the general principle of virtual work are used to formulate the interface element for a finite element solution procedure. Some advantages of the interface element include; easy implementation intostandard finite element programs, direct determination of interface forces without round-off problems, and the generality afforded by the virtual work formulation to include other non-conservative models in the system. The application of the interface element to an idealized buried culvert problem illustrates that the model behaves properly. A second application, for a long-span culvert installation with incremental soil loading, demonstrates the importance of modelling slippage at the culvert–soil interface in order to conform with experimental observations. 相似文献
10.
Three dimensional elasto‐plastic interface for embedded beam elements with interaction surface for the analysis of lateral loading of piles 
下载免费PDF全文
下载免费PDF全文 This paper presents a numerical formulation for a three dimensional elasto‐plastic interface, which can be coupled with an embedded beam element in order to model its non‐linear interaction with the surrounding solid medium. The formulation is herein implemented for lateral loading of piles but is able to represent soil‐pile interaction phenomena in a general manner for different types of loading conditions or ground movements. The interface is formulated in order to capture localized material plasticity in the soil surrounding the pile within the range of small to moderate lateral displacements. The interface is formulated following two different approaches: (i) in terms of beam degrees of freedoms; and (ii) considering the displacement field of the solid domain. Each of these alternatives has its own advantages and shortcomings, which are discussed in this paper. The paper presents a comparison of the results obtained by means of the present formulation and by other well‐established analysis methods and test results published in the literature. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
11.
Composite element model for the bonded anchorage head of stranded wire cable in tension 总被引：1，自引：0，他引：1 下载免费PDF全文
下载免费PDF全文 An elasto‐viscoplastic model is formulated using composite element technique for the bonded anchorage head of stranded wire cable in rock mass. This composite element contains sub‐elements corresponding to the rock material, the grout material, the stranded wire material, the rock/grout interface, and the grout/stranded wire interface, respectively. The displacement in each aforementioned sub‐element is interpolated from the corresponding nodal displacements of the composite element. In this manner, the mesh generation taking into account of tension cable anchors may be highly facilitated. By the application of the virtual work principle, the governing equation for solving the nodal displacements of the composite element is established. The proposed model has been incorporated into the conventional finite element algorithm and implemented in the program CORE3, in which the anchorage head is embedded within the composite elements. The comparative study concerning the pull‐out test has been carried out for the validation of the proposed model and algorithm. Copyright © 2015 John Wiley & Sons, Ltd. 相似文献
12.
13.
14.
15.
16.
桩-土相互作用问题是岩土工程桩基础问题的关键点与难点,目前针对桩身在循环温度荷载与上覆结构荷载双重作用下的能源桩承载特性研究较少。在传统理想弹塑性模型及双曲线模型的基础上,采用分段非线性的方法对桩-土荷载传递骨干曲线进行了修正,并基于Masing’s循环准则,提出了适用于能源桩的桩-土荷载传递模型。利用改进的桩-土荷载传递模型对能源桩承载特性进行数值分析,着重研究了桩-土荷载传递参数比R对能源桩受力情况的影响。此外,为了探究在上覆结构荷载及循环温度荷载双重作用下,能源桩与周围土体之间的真实荷载传递关系及其结构热力学特性,开展了针对能源桩与周围土体之间相互作用问题的室内模型试验,监测了其桩身轴向应力及侧摩阻力随温度及深度变化的趋势,并与基于改进荷载传递模型的数值计算结果进行了对比。室内模型试验监测及数值计算结果显示：能源桩在上覆结构荷载及温度循环荷载双重作用下,其受力行为受改进的桩-土荷载传递循环曲线控制;基于改进的桩-土荷载传递循环曲线而建立的数值模型计算结果与试验结果基本吻合,改进的桩-土荷载传递模型能够较好发地反映能源桩实际的承载特性。 相似文献
17.
The cyclic behavior of soil–structure interface can be very important in dynamic problems. The cyclic behavior of soil–structure interface may be nonlinear, which includes hysteresis, hardening, degradation, and particle breakage. The breakage of granular soil particles during shearing of granular soil–structure interface is associated with cyclic degradation and can be critical to the dynamic behavior of soil–structure system. The critical state soil mechanics concept formerly used to simulate the nonlinear monotonic behavior of granular soil–structure interface was modified and extended to describe the cyclic behavior, especially soil‐particle breakage and degradation during cyclic shearing. Soil‐particle breakage was assumed to relate to the energy consumption during cyclic shearing and the critical state line of the soil–structure interface was assumed to translate with the consumption of shearing energy during cyclic shearing as the threshold value is attained. The model was formulated in the framework of generalized plasticity and is capable of describing the salient features of granular soil–structure interface under cyclic loading. Most of the model parameters have straightforward physical meanings and are calibrated using monotonic or cyclic interface test results. The proposed model was calibrated and validated against published test results. The dependency of interface behavior on stress path and cyclic degradation can be successfully described by the proposed model. Copyright © 2008 John Wiley & Sons, Ltd. 相似文献
18.
Numerical modelling of rock slides is a versatile approach to understand the failure mechanism and the dynamics of rock slopes. Finite element slope stability analysis of three rock slopes in Garhwal Himalaya, India has been carried out using a two dimensional plane strain approach. Two different modelling techniques have been attempted for this study. Firstly, the slope is represented as a continuum in which the effect of discontinuities is considered by reducing the properties and strength of intact rock to those of rock mass. The equivalent Mohr-Coulomb shear strength parameters of generalised Hoek-Brown (GHB) criterion and modified Mohr-Coulomb (MMC) criterion has been used for this continuum approach. Secondly, a combined continuum-interface numerical method has been attempted in which the discontinuities are represented as interface elements in between the rock walls. Two different joint shear strength models such as Barton-Bandis and Patton’s model are used for the interface elements. Shear strength reduction (SSR) analysis has been carried out using a finite element formulation provided in the PHASE2. For blocky or very blocky rock mass structure combined continuum-interface model is found to be the most suitable one, as this model is capable of simulating the actual field scenario. 相似文献
19.
Composite Element Model of the Fully Grouted Rock Bolt 总被引：12，自引：1，他引：12
Summary The three dimensional elasto-viscoplastic composite element method is formulated in this paper for rock masses reinforced by a fully-grouted bolt. If a bolt segment penetrates a finite element representing the rock mass, then a composite element is formed including five sub-elements corresponding to the rock material, the grout material, the bolt material, the rock-grout interface and the bolt-grout interface. The displacements in each sub-element are interpolated from the corresponding nodal displacements of the composite element. By the virtual work principle the governing equation for the solution of the nodal displacements can be formulated. The elasto-viscoplastic characteristics of the materials are considered in the formulation. The new model can be incorporated into the conventional finite element analysis grid, in which several composite elements have fully grouted bolts embedded. In this way the mesh generation of large scale bolted rock structures becomes convenient and feasible. The model has been implemented in a FEM program, and a comparative study between the numerical analysis and a pull out field test has been carried out, from which the validity and the robustness of the new model are justified. 相似文献
20.
讨论了亿万单元有限元模型的可扩展并行计算方法。从软件和硬件两个方面提出了前处理、并行计算方法、程序算法、后处理实现等核心问题的解决方案。采用网格加密方法生成一亿单元的有限元模型,利用对偶原始有限元撕裂内联法（FETI-DP）求解系统方程。基于图论理论建立了子区域间的通讯拓扑关系,实现了子区域间点对点通讯,避免速度慢、通信量大的全局通讯。在自主开发程序基础上,增加相应模块,采用面向对象编程技术和MPI消息传递库开发程序。对一个一亿多单元的工程实例运用5 000核并行计算,得到了超线性加速比。计算结果在专用图形工作站上进行后处理,显示和交互操作速度良好。研究在两方面实现了突破：一是将模型规模提高到了一亿多单元;二是同时调用了5 000个计算核来并行运算,并得到了很高效率。高分辨率有限元并行模拟研究成果可为岩土工程中结构特别复杂、计算区域特别大、地质情况复杂等模拟提供很好的技术方法和实现手段。 相似文献