首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 673 毫秒
1.
The solubility and incorporation mechanisms of water in synthetic and natural MgAl2O4 spinel have been investigated in a series of high-pressure/temperature annealing experiments. In contrast to most other nominally anhydrous minerals, natural spinel appears to be completely anhydrous. On the other hand, non-stoichiometric Al-rich synthetic (defect) spinel can accommodate several hundred ppm water in the form of structurally-incorporated hydrogen. Infrared (IR) spectra of hydrated defect spinel contain one main O-H stretching band at 3343-3352 cm−1 and a doublet consisting of two distinct O-H bands at 3505-3517 cm−1 and 3557-3566 cm−1. IR spectra and structural refinements based on single-crystal X-ray data are consistent with hydrogen incorporation in defect spinel onto both octahedral and tetrahedral O-O edges. Fine structure of O-H bands in IR spectra can be explained by partial coupling of interstitial hydrogen with cation vacancies, or by the effects of Mg-Al disorder on the tetrahedral site. The concentration of cation vacancies in defect spinel is a major control on hydrogen affinity. The commercial availability of large single crystals of defect spinel coupled with high water solubility and similarities in water incorporation mechanisms between hydrous defect spinel and hydrous ringwoodite (Mg2SiO4) suggests that synthetic defect spinel may be a useful low-pressure analogue material for investigating the causes and consequences of water incorporation in the lower part of Earth’s mantle transition zone.  相似文献   

2.
Aqueous Co(II) chloride complexes play a crucial role in cobalt transport and deposition in ore-forming hydrothermal systems, ore processing plants, and in the corrosion of special Co-bearing alloys. Reactive transport modelling of cobalt in hydrothermal fluids relies on the availability of thermodynamic properties for Co complexes over a wide range of temperature, pressure and salinity. Synchrotron X-ray absorption spectroscopy was used to determine the speciation of cobalt(II) in 0-6 m chloride solutions at temperatures between 35 and 440 °C at a constant pressure of 600 bar. Qualitative analysis of XANES spectra shows that octahedral species predominate in solution at 35 °C, while tetrahedral species become increasingly important with increasing temperature. Ab initio XANES calculations and EXAFS analyses suggest that in high temperature solutions the main species at high salinity (Cl:Co >> 2) is CoCl42−, while a lower order tetrahedral complex, most likely CoCl2(H2O)2(aq), predominates at low salinity (Cl:Co ratios ∼2). EXAFS analyses further revealed the bonding distances for the octahedral Co(H2O)62+ (octCo-O = 2.075(19) Å), tetrahedral CoCl42− (tetCo-Cl = 2.252(19) Å) and tetrahedral CoCl2(H2O)2(aq) (tetCo-O = 2.038(54) Å and tetCo-Cl = 2.210(56) Å). An analysis of the Co(II) speciation in sodium bromide solutions shows a similar trend, with tetrahedral bromide complexes becoming predominant at higher temperature/salinity than in the chloride system. EXAFS analysis confirms that the limiting complex at high bromide concentration at high temperature is CoBr42−. Finally, XANES spectra were used to derive the thermodynamic properties for the CoCl42− and CoCl2(H2O)2(aq) complexes, enabling thermodynamic modelling of cobalt transport in hydrothermal fluids. Solubility calculations show that tetrahedral CoCl42− is responsible for transport of cobalt in hydrothermal solutions with moderate chloride concentration (∼2 m NaCl) at temperatures of 250 °C and higher, and both cooling and dilution processes can cause deposition of cobalt from hydrothermal fluids.  相似文献   

3.
The influence on the structure of Fe2+ Mg substitution was studied in synthetic single crystals belonging to the MgCr2O4–FeCr2O4 series produced by flux growth at 900–1200 °C in controlled atmosphere. Samples were analyzed by single-crystal X-ray diffraction, electron microprobe analyses, optical absorption-, infrared- and Mössbauer spectroscopy. The Mössbauer data show that iron occurs almost exclusively as IVFe2+. Only minor Fe3+ (<0.005 apfu) was observed in samples with very low total Fe. Optical absorption spectra show that chromium with few exceptions is present as a trivalent cation at the octahedral site. Additional absorption bands attributable to Cr2+ and Cr3+ at the tetrahedral site are evident in spectra of end-member magnesiochromite and solid-solution crystals with low ferrous contents. Structural parameters a0, u and T–O increase with chromite content, while the M–O bond distance remains nearly constant, with an average value equal to 1.995(1) Å corresponding to the Cr3+ octahedral bond distance. The ideal trend between cell parameter, T–O bond length and Fe2+ content (apfu) is described by the following linear relations: a0=8.3325(5) + 0.0443(8)Fe2+ (Å) and T–O=1.9645(6) + 0.033(1)Fe2+ (Å) Consequently, Fe2+ and Mg tetrahedral bond lengths are equal to 1.998(1) Å and 1.965(1) Å, respectively.  相似文献   

4.
Reaction between dissolved water and sulphide was experimentally investigated in soda-lime-silicate (NCS) and sodium trisilicate (NS3) melts at temperatures from 1000 to 1200 °C and pressures of 100 or 200 MPa in internally heated gas pressure vessels. Diffusion couple experiments were conducted at water-undersaturated conditions with one half of the couple being doped with sulphide (added as FeS or Na2S; 1500-2000 ppm S by weight) and the other with H2O (∼3.0 wt.%). Additionally, two experiments were performed using a dry NCS glass cylinder and a free H2O fluid. Here, the melt was water-saturated at least at the melt/fluid interface. Profiling by electron microprobe (sulphur) and infrared microscopy (H2O) demonstrate that H2O diffusion in the melts is faster by 1.5-2.3 orders of magnitude than sulphur diffusion and, hence, H2O can be considered as a rapidly diffusing oxidant while sulphur is quasi immobile in these experiments.In Raman spectra a band at 2576 cm−1 appears in the sulphide - H2O transition zone which is attributed to fundamental S-H stretching vibrations. Formation of new IR absorption bands at 5025 cm−1 (on expense of the combination band of molecular H2O at 5225 cm−1) and at 3400 cm−1 was observed at the front of the in-diffusing water in the sulphide bearing melt. The appearance and intensity of these two IR bands is correlated with systematic changes in S K-edge XANES spectra. A pre-edge excitation at 2466.5 eV grows with increasing H2O concentration while the sulphide peak at 2474.0 eV decreases in intensity relative to the peak at 2477.0 eV and the feature at 2472.3 eV becomes more pronounced (all energies are relative to the sulphate excitation, calibrated to 2482.5 eV). The observations by Raman, IR and XANES spectroscopy indicate a well coordinated S2− - H2O complex which was probably formed in the glasses during cooling at the glass transition. No oxidation of sulphide was observed in any of the diffusion couple experiments. On the contrary, XANES spectra from experiments conducted with a free H2O fluid show complete transformation of sulphide to sulphate near the melt surface and coexistence of sulphate and sulphide in the center of the melt. This can be explained by a lower H2O activity in the diffusion couple experiments or by the need of a sink for hydrogen (e.g., a fluid which can dissolve high concentration of hydrogen) to promote oxidation of sulphide by H2O via the reaction S2− + 4H2O = SO42− + 4H2. Sulphite could not be detected in any of the XANES spectra implying that this species, if it exists in the melt, it is a subordinate or transient species only.  相似文献   

5.
The IR spectrum of an alpine, hydrothermally formed diopside containing 17 wt ppm H2O consists of three main OH absorption bands centred at 3647, 3464 and 3359 cm−1. Jadeite from a Californian vein occurrence is characterised by bands at 3616 and 3557 cm−1 and contains about 197 wt ppm H2O. Based on the pleochroic scheme of the OH absorption bands in diopside, OH defect incorporation models are derived on the basis of fully occupied cation sites and under the assumption of M1 and M2 site vacancies; OH defects replacing O2 oxygen atoms are most common. The less pronounced OH pleochroism and the broad band absorption pattern of jadeite indicate a high degree of OH defect disordering. The pleochroic scheme of the main absorption bands at 3616 and 3557 cm−1 implies partial replacement of O2 oxygen atoms by OH dipoles pointing to vacant Si sites. Under the assumption of M1 and M2 site vacancies, O1–H and O2–H defects are also derivable. OH incorporation modes assuming Si-vacancies should be considered for jadeite-rich clinopyroxenes formed in deep crust and upper mantle regions.  相似文献   

6.
The present study illustrates the interest of using the elastic recoil detection analysis (ERDA) method to characterize any geological sample matrix with respect to hydrogen. ERDA is combined with Rutherford back scattering (RBS) and particle induced X-ray emission (PIXE), allowing the simultaneous characterization of the matrix with respect to major and trace elements (Z > 15). Analyses are performed by mapping of a 4 × 16 μm2 incident beam of 4He+ on large areas (50 × 200 μm2). The method is almost not destructive and requires no calibration with respect to well known hydrous samples. Hydrous and nominally anhydrous phases in contact with each other in the same sample may both be characterized. The depth of the analyses is limited to several μm beneath the surface, allowing tiny samples to be investigated, provided their sizes are larger than the incident beam. Our setup has been improved in order to allow H determination on a micrometric scale with a 5-15% relative uncertainty and a detection limit of 94 wt ppm H2O. We present multi-elemental mappings on a large panel of samples: (1) natural and analogue synthetic glasses from Stromboli volcano (0.44-4.59 wt% H2O), natural rhyolitic glasses (1466-1616 wt ppm H2O); (2) magmatic rhyolitic melt inclusions from Guadeloupe Island (4.37-5.47 wt% H2O) and their quartz host crystal (2020 ± 230 wt ppm H2O); (3) nominally anhydrous natural (82-260 wt ppm H2O) and experimentally hydrated (240-790 wt ppm H2O) olivines; natural clinopyroxenes (159-716 wt ppm H2O); natural orthopyroxenes (201-452 wt ppm H2O); a natural garnet (90 wt ppm H2O). Results show that ERDA is a strong and accurate reference method that can be used to characterize geological sample from various matrix compositions from high to low water contents. It can be used to calibrate other methods of microanalysis such as Fourier Transform Infrared Spectroscopy (FTIR) or secondary ion mass spectrometry (SIMS).  相似文献   

7.
Although, the kinetic reactivity of a mineral surface is determined, in part, by the rates of exchange of surface-bound oxygens and protons with bulk solution, there are no elementary rate data for minerals. However, such kinetic measurements can be made on dissolved polynuclear clusters, and here we report lifetimes for protons bound to three oxygen sites on the AlO4Al12(OH)24(H2O)127+ (Al13) molecule, which is a model for aluminum-hydroxide solids in water. Proton lifetimes were measured using 1H NMR at pH ∼ 5 in both aqueous and mixed solvents. The 1H NMR peak for protons on bound waters (η-H2O) lies near 8 ppm in a 2.5:1 mixture of H2O/acetone-d6 and broadens over the temperature range −20 to −5 °C. Extrapolated to 298 K, the lifetime of a proton on a η-H2O is τ298 ∼ 0.0002 s, which is surprisingly close to the lifetime of an oxygen in the η-H2O (∼0.0009 s), but in the same general range as lifetimes for protons on fully protonated monomer ions of trivalent metals (e.g., Al(H2O)63+). The lifetime is reduced somewhat by acid addition, indicating that there is a contribution from the partly deprotonated Al13 molecule in addition to the fully protonated Al13 at self-buffered pH conditions. Proton lifetimes on the two distinct sets of hydroxyls bridging two Al(III) (μ2-OH) differ substantially and are much shorter than the lifetime of an oxygen at these sites. The average lifetimes for hydroxyl protons were measured in a 2:1 mixture of H2O/dmso-d6 over the temperature range 3.7-95.2 °C. The lifetime of a hydrogen on one of the μ2-OH was also measured in D2O. The τ298 values are ∼0.013 and ∼0.2 s in the H2O/dmso-d6 solution and the τ298 value for the μ2-OH detectable in D2O is τ298 ∼ 0.013 s. The 1H NMR peak for the more reactive μ2-OH broadens slightly with acid addition, indicating a contribution from an exchange pathway that involves a proton or hydronium ion. These data indicate that surface protons on minerals will equilibrate with near-surface waters on the diffusional time scale.  相似文献   

8.
The structure of H2O-saturated silicate melts and of silicate-saturated aqueous solutions, as well as that of supercritical silicate-rich aqueous liquids, has been characterized in-situ while the sample was at high temperature (to 800 °C) and pressure (up to 796 MPa). Structural information was obtained with confocal microRaman and with FTIR spectroscopy. Two Al-bearing glasses compositionally along the join Na2O•4SiO2-Na2O•4(NaAl)O2-H2O (5 and 10 mol% Al2O3, denoted NA5 and NA10) were used as starting materials. Fluids and melts were examined along pressure-temperature trajectories of isochores of H2O at nominal densities (from PVT properties of pure H2O) of 0.85 g/cm3 (NA10 experiments) and 0.86 g/cm3 (NA5 experiments) with the aluminosilicate + H2O sample contained in an externally-heated, Ir-gasketed hydrothermal diamond anvil cell.Molecular H2O (H2O°) and OH groups that form bonds with cations exist in all three phases. The OH/H2O° ratio is positively correlated with temperature and pressure (and, therefore, fugacity of H2O, fH2O) with (OH/H2O°)melt > (OH/H2O°)fluid at all pressures and temperatures. Structural units of Q3, Q2, Q1, and Q0 type occur together in fluids, in melts, and, when outside the two-phase melt + fluid boundary, in single-phase liquids. The abundance of Q0 and Q1 increases and Q2 and Q3 decrease with fH2O. Therefore, the NBO/T (nonbridging oxygen per tetrahedrally coordination cations), of melt is a positive function of fH2O. The NBO/T of silicate in coexisting aqueous fluid, although greater than in melt, is less sensitive to fH2O.The melt structural data are used to describe relationships between activity of H2O and melting phase relations of silicate systems at high pressure and temperature. The data were also combined with available partial molar configurational heat capacity of Qn-species in melts to illustrate how these quantities can be employed to estimate relationships between heat capacity of melts and their H2O content.  相似文献   

9.
Armenite, ideal formula BaCa2Al6Si9O30·2H2O, and its dehydrated analog BaCa2Al6Si9O30 and epididymite, ideal formula Na2Be2Si6O15·H2O, and its dehydrated analog Na2Be2Si6O15 were studied by low-temperature relaxation calorimetry between 5 and 300 K to determine the heat capacity, Cp, behavior of their confined H2O. Differential thermal analysis and thermogravimetry measurements, FTIR spectroscopy, electron microprobe analysis and powder Rietveld refinements were undertaken to characterize the phases and the local environment around the H2O molecule.The determined structural formula for armenite is Ba0.88(0.01)Ca1.99(0.02)Na0.04(0.01)Al5.89(0.03)Si9.12(0.02)O30·2H2O and for epididymite Na1.88(0.03)K0.05(0.004)Na0.01(0.004)Be2.02(0.008)Si6.00(0.01)O15·H2O. The infrared (IR) spectra give information on the nature of the H2O molecules in the natural phases via their H2O stretching and bending vibrations, which in the case of epididymite only could be assigned. The powder X-ray diffraction data show that armenite and its dehydrated analog have similar structures, whereas in the case of epididymite there are structural differences between the natural and dehydrated phases. This is also reflected in the lattice IR mode behavior, as observed for the natural phases and the H2O-free phases. The standard entropy at 298 K for armenite is S° = 795.7 ± 6.2 J/mol K and its dehydrated analog is S° = 737.0 ± 6.2 J/mol K. For epididymite S° = 425.7 ± 4.1 J/mol K was obtained and its dehydrated analog has S° = 372.5 ± 5.0 J/mol K. The heat capacity and entropy of dehydration at 298 K are Δ = 3.4 J/mol K and ΔSrxn = 319.1 J/mol K and Δ = −14.3 J/mol K and ΔSrxn = 135.7 J/mol K for armenite and epididymite, respectively. The H2O molecules in both phases appear to be ordered. They are held in place via an ion-dipole interaction between the H2O molecule and a Ca cation in the case of armenite and a Na cation in epididymite and through hydrogen-bonding between the H2O molecule and oxygen atoms of the respective silicate frameworks. Of the three different H2O phases ice, liquid water and steam, the Cp behavior of confined H2O in both armenite and epididymite is most similar to that of ice, but there are differences between the two silicates and from the Cp behavior of ice. Hydrogen-bonding behavior and its relation to the entropy of confined H2O at 298 K is analyzed for various microporous silicates.The entropy of confined H2O at 298 K in various silicates increases approximately linearly with increasing average wavenumber of the OH-stretching vibrations. The interpretation is that decreased hydrogen-bonding strength between a H2O molecule and the silicate framework, as well as weak ion-dipole interactions, results in increased entropy of H2O. This results in increased amplitudes of external H2O vibrations, especially translations of the molecule, and they contribute strongly to the entropy of confined H2O at T < 298 K.  相似文献   

10.
The solubility of Fe-ettringite (Ca6[Fe(OH)6]2(SO4)3 · 26H2O) was measured in a series of precipitation and dissolution experiments at 20 °C and at pH-values between 11.0 and 14.0 using synthesised material. A time-series study showed that equilibrium was reached within 180 days of ageing. After equilibrating, the solid phases were analysed by XRD and TGA while the aqueous solutions were analysed by ICP-OES (calcium, sulphur) and ICP-MS (iron). Fe-ettringite was found to be stable up to pH 13.0. At higher pH-values Fe-monosulphate (Ca4[Fe(OH)6]2(SO4) · 6H2O) and Fe-monocarbonate (Ca4[Fe(OH)6]2(CO3) · 6H2O) are formed. The solubilities of these hydrates at 25 °C are:   相似文献   

11.
To understand possible volcanogenic fluxes of CO2 to the Martian atmosphere, we investigated experimentally carbonate solubility in a synthetic melt based on the Adirondack-class Humphrey basalt at 1-2.5 GPa and 1400-1625 °C. Starting materials included both oxidized and reduced compositions, allowing a test of the effect of iron oxidation state on CO2 solubility. CO2 contents in experimental glasses were determined using Fourier transform infrared spectroscopy (FTIR) and Fe3+/FeT was measured by Mössbauer spectroscopy. The CO2 contents of glasses show no dependence on Fe3+/FeT and range from 0.34 to 2.12 wt.%. For Humphrey basalt, analysis of glasses with gravimetrically-determined CO2 contents allowed calibration of an integrated molar absorptivity of 81,500 ± 1500 L mol−1 cm−2 for the integrated area under the carbonate doublet at 1430 and 1520 cm−1. The experimentally determined CO2 solubilities allow calibration of the thermodynamic parameters governing dissolution of CO2 vapor as carbonate in silicate melt, KII, (Stolper and Holloway, 1988) as follows: , ΔV0 = 20.85 ± 0.91 cm3 mol−1, and ΔH0 = −17.96 ± 10.2 kJ mol−1. This relation, combined with the known thermodynamics of graphite oxidation, facilitates calculation of the CO2 dissolved in magmas derived from graphite-saturated Martian basalt source regions as a function of P, T, and fO2. For the source region for Humphrey, constrained by phase equilibria to be near 1350 °C and 1.2 GPa, the resulting CO2 contents are 51 ppm at the iron-wüstite buffer (IW), and 510 ppm at one order of magnitude above IW (IW + 1). However, solubilities are expected to be greater for depolymerized partial melts similar to primitive shergottite Yamato 980459 (Y 980459). This, combined with hotter source temperatures (1540 °C and 1.2 GPa) could allow hot plume-like magmas similar to Y 980459 to dissolve 240 ppm CO2 at IW and 0.24 wt.% of CO2 at IW + 1. For expected magmatic fluxes over the last 4.5 Ga of Martian history, magmas similar to Humphrey would only produce 0.03 and 0.26 bars from sources at IW and IW + 1, respectively. On the other hand, more primitive magmas like Y 980459 could plausibly produce 0.12 and 1.2 bars at IW and IW + 1, respectively. Thus, if typical Martian volcanic activity was reduced and the melting conditions cool, then degassing of CO2 to the atmosphere may not be sufficient to create greenhouse conditions required by observations of liquid surface water. However, if a significant fraction of Martian magmas derive from hot and primitive sources, as may have been true during the formation of Tharsis in the late Noachian, that are also slightly oxidized (IW + 1.2), then significant contribution of volcanogenic CO2 to an early Martian greenhouse is plausible.  相似文献   

12.
Fe-, Cr- and Al-spinels were synthesized and their unit cell sizes determined by means of X-rays. Differential thermal curves show that the magnetic inversion of Fe2O3 at 680° C accelerates the formation of the ferrites when the constituent oxides are heated together.A correlation can be made between ionic radii of cations and unit cell dimensions provided the effect of covalent forces in the lattice is taken into account. The values for ionic radii of cations as given byAhrens (1952) permit a better correlation than those ofGoldschmidt.A shrinkage of 0.01 Å in the unit cell size per 0.01 Å decrease in the ionic radius of the divalent cations was determined when spinels with the same cation arrangement in the same group were compared. A shrinkage of 0.027 Å in the unit cell size per 0.01 Å decrease in the ionic radius of the trivalent cations was determined in spinels having the same divalent cation and cation arrangement when the trivalent cations form the same type of bonds.The half-occupation of the 3d orbits in Mn2+ and Fe3+ causes abnormally high unit cell dimensions in spinels where these ions are incorporated in octahedral sites. This is attributed to the formation of electrovalent bonds by these ions. Variable forces of contraction in the lattice are revealed when the unit cell dimensions are correlated with the ionic radii of cations. The force of contraction can be satisfactorily explained as being due to covalent forces in the spinel structure. The magnitude of this force or the degree of covalence in the bonds increases in the following order of cations where these are situated in tetrahedral sites:The divalent transition element ions, Fe2+, Co2+ and Ni2+; the B-Sub-group element ions Cd2+ and Zn2+; Fe3+ in tetrahedral co-ordination.  相似文献   

13.
In this study, the solubility constant of magnesium chloride hydroxide hydrate, Mg3Cl(OH)5·4H2O, termed as phase 5, is determined from a series of solubility experiments in MgCl2-NaCl solutions. The solubility constant in logarithmic units at 25 °C for the following reaction,
Mg3Cl(OH)5·4H2O+5H+=3Mg2++9H2O(l)+Cl-  相似文献   

14.
Monte Carlo simulations show that the adsorption position of the Sr2+ or Ba2+ ion on the cleaved muscovite surface is determined by the radius of the ion’s first hydration shell, hydrogen bonding of the first shell water molecules with the basal oxygens of muscovite as well as a requirement of minimization of the number of muscovite’s lattice cations in the ion’s first coordination shell. Accordingly, Sr2+ or Ba2+ adsorbs in ditrigonal cavities at a distance of 1.12 Å or 1.35 Å, respectively, from the basal surface on dehydrated mica and above tetrahedral substitutions at a height of 1.93 ± 0.02 Å or 2.15 ± 0.03 Å, respectively, at the highest simulated water coverage of 28 H2O per ion. The ion’s displacement from a ditrigonal cavity occurs upon adsorption of 2 H2O per ion for Sr2+ and 3 H2O per ion for Ba2+. At a coverage of 28 H2O per ion, outer-sphere adsorption of Sr2+ or Ba2+ at a height of 3.9 ± 0.2 Å or 4.17 ± 0.07 Å, respectively, is possible albeit unfavorable on the free energy scale by 107 ± 7 kJ/mol or 89 ± 13 kJ/mol, respectively, as compared to inner-sphere adsorption. Activation energies for the transformation between inner-sphere and outer-sphere adsorptions are calculated to be 121 ± 3 kJ/mol for Sr2+ and 99 ± 10 kJ/mol for Ba2+. A comparison of these values with those reported recently for Mg2+ and Ca2+ results in an adsorption affinity sequence Mg2+ > Ca2+ > Sr2+ > Ba2+ in agreement with the sequence predicted recently for low dielectric constant solids (which include mica) (Sverjensky, 2006). A recent resonant anomalous X-ray reflectivity study of Sr2+ adsorption on muscovite (Park et al., 2006) has questioned the common assumption (Stumm, 1992), which is supported by the present simulation results, that inner-sphere adsorption is stronger than outer-sphere adsorption. A modification of the cleaved muscovite surface as a result of Sr2+ adsorption in muscovite’s ditrigonal cavities and related destabilization of muscovite’s hydroxyl groups is proposed as a possible reason for this controversy.  相似文献   

15.
Garnet and omphacite from ultrahigh-pressure eclogites from the Dabie orogen, eastern China were investigated by Micro-FTIR. The results show that all garnet and omphacite grains contain structural water occurring as hydroxyl (OH), with H2O contents varying from 14 to 1915 ppm (H2O wt) and from 105 to 695 ppm, respectively. Within the same sample, the water contents are either homogeneous at the grain scale or vary systematically from higher in the core to lower in the rim. Low water contents at crystal rims possibly result from hydroxyl exsolution after pressure decrease upon rock exhumation. The δD values of omphacites are between −108.4‰ and −114.2‰, and independent of water contents. Heterogeneous water contents of garnet occur at the centimeter scale and fluid mobility during UHP metamorphism was very limited. The estimated whole-rock water content based on mineral H2O contents is between 260 and 750 ppm, thereby implying that eclogitic rocks formed during continental subduction have the potential to recycle (at least) several hundreds ppm water to mantle depths. The preserved chemical differences likely indicate that the eclogitic rocks resided at mantle conditions for a limited time span, and imply that they were exhumed shortly after subduction. The water released during decompression might represent the early-stage retrograde fluid.  相似文献   

16.
Summary The crystal structure of sigloite, Fe3 [(H2O)3OH] [Al2(PO4)2(OH)2(H2O)2]- 2 H2O, triclinic, a 5.190 (2), b 10.419 (4), c 7.033 (3) Å, 105.00 (3), 111.31(3), 70.87 (3)°, V 330.5 (2) Å3, Z = 1, space group P , has been refined to anR index of 5.3% using 1713 observed (I > 2.5 1) reflections collected with graphite-monochromated MoK X-rays. Sigloite is isostructural with the laueite-group minerals. Corner-linked [A15] chains (: unspecified ligand) are cross-linked by (PO4) tetrahedra to form a mixed corner-linked tetrahedral-octahedral sheet of composition [A12(PO4)2(OH)2(H2O)2]2-. These sheets are linked by (Fe3+O2(OH, H2O)4) octahedra and two (H2O) groups that participate in a hydrogen-bonding network. Sigloite is the oxidized equivalent of paravauxite, Fe2+(H2O)4[Al2(PO4)2(OH)2(H2O)2]-2 H2O, and detailed comparison of the two structures shows that the oxidation mechanism involves loss of hydrogen from one of the (H2O) groups coordinating the Fe3+, and positional disorder of both the Fe3+ and (OH) and (H2O) ligands.
Siggloit: Der Oxidationsmechanismus in (M 2 3 + (PO4)2(OH)2(H2O)2]2- Strukturen
Zusammenfassung Die Kristallstruktur von Sigloit, Fe3+ [(H2O)3OH] [Al2(PO4)2(OH)2(H2O)2].2 H2O, triklin, a 5,190 (2), b 10,419 (4), c 7,033 (3) Å, 105,00 (3), 111,31 (3), 70,87 (3)°, V 330,5 (2) Å3,Z = 1, Raumgruppe P , wurdefür 1713 beobachtete Reflexe (I > 2,5 I), die mit MoKa-Röntgenstrahlung (Graphit-Monochromator) gesammelt wurden, auf einen R-Wert von 5,3% verfeinert. Sigloit ist isotyp mit den Mineralen deer Laueit-Gruppe. Über Ecken verknüpfte [A15]-Ketten (: nicht spezifizierter Ligand) werden über (P04)-Tetraeder zu ebenfalls über Ecken verknüpfte Tetraeder-OktaederSchichten der Zusammensetzung [A12(PO4)2(OH)2(H2O)2]2- verbunden. Diese Schichten werden über (Fe3+O2(OH, H2O)4)-Oktaeder und zwei (H2O)-Gruppen, die amWasserstoffbrücken-Netzwerk beteiligt sind, verbunden. Sigloit ist das oxidierte Analogon zu Paravauxit, Fe2+(H2O)4[A12(PO4)2(OH)2(H2O)2] - 2 H2O; ein detaillierter Vergleich dieser beiden Strukturen zeigt, daß der Oxidationsmechanismus sowohl den Verlust eines Wasserstoffatoms (H2O)-Gruppe, welche ein Fe3+-Atom koordiniert, als auch eine Fehlordnung der Punktlagen von Fe3+ und von den (OH) und (H2O) Liganden bedingt.
  相似文献   

17.
Biogeochemical cycling of zinc is strongly influenced by sorption on birnessite minerals (layer-type MnO2), which are found in diverse terrestrial and aquatic environments. Zinc has been observed to form both tetrahedral (ZnIV) and octahedral (ZnVI) triple-corner-sharing surface complexes (TCS) at Mn(IV) vacancy sites in hexagonal birnessite. The octahedral complex is expected to be similar to that of Zn in the Mn oxide mineral, chalcophanite (ZnMn3O7·3H2O), but the reason for the occurrence of the four-coordinate Zn surface species remains unclear. We address this issue computationally using spin-polarized density functional theory (DFT) to examine the ZnIV-TCS and ZnVI-TCS species. Structural parameters obtained by DFT geometry optimization were in excellent agreement with available experimental data on Zn-birnessites. Total energy, magnetic moments, and electron overlap populations obtained by DFT for isolated ZnIV-TCS revealed that this species is stable in birnessite without a need for Mn(III) substitution in the octahedral sheet and that it is more effective in reducing undersaturation of surface O at a Mn vacancy than is ZnVI-TCS. Comparison between geometry-optimized ZnMn3O7·3H2O (chalcophanite) and the hypothetical monohydrate mineral, ZnMn3O7·H2O, which contains only tetrahedral Zn, showed that the hydration state of Zn significantly affects birnessite structural stability. Finally, our study also revealed that, relative to their positions in an ideal vacancy-free MnO2, Mn nearest to Zn in a TCS surface complex move toward the vacancy by 0.08-0.11 Å, while surface O bordering the vacancy move away from it by 0.16-0.21 Å, in agreement with recent X-ray absorption spectroscopic analyses.  相似文献   

18.
Recent isopiestic studies of the Fe2(SO4)3-H2SO4-H2O system at 298.15 K are represented with an extended version of Pitzer’s ion interaction model. The model represents osmotic coefficients for aqueous {(1 − y)Fe2(SO4)3 + yH2SO4} mixtures from 0.45 to 3.0 m at 298.15 K and 0.0435 ? y ? 0.9370. In addition, a slightly less accurate representation of a more extended molality range to 5.47 m extends over the same y values, translating to a maximum ionic strength of 45 m. Recent isopiestic data for the system at 323.15 K are represented with the extended Pitzer model over a limited range in molality and solute fraction. These datasets are also represented with the usual “3-parameter” version of Pitzer’s model so that it may be incorporated in geochemical modeling software, but is a slightly less accurate representation of thermodynamic properties for this system. Comparisons made between our ion interaction model and available solubility data display partial agreement for rhomboclase and significant discrepancy for ferricopiapite. The comparisons highlight uncertainty remaining for solubility predictions in this system as well as the need for additional solubility measurements for Fe3+-bearing sulfate minerals. The resulting Pitzer ion interaction models provide an important step toward an accurate and comprehensive representation of thermodynamic properties in this geochemically important system.  相似文献   

19.
Summary Anandite has an approximate formula of Ba(Fe3+, Fe2+)3[Si2(Fe3+, Fe2+, Si)2O10–x(OH)x] (S, Cl) (OH), withx=0–1, and belongs to the 2 O brittle mica group. It is orthorhombic; space groupPnmn;a=5.468(9) Å,b=9.489(18)Å,c=19.963(11) Å;Z=4.The structure was determined from 3dim. Weissenberg-data, starting with an approximate structure in the pseudo space groupCcmm. Least squares refinement resulted inR=0.061 for 409 photometric intensities, andR=0.131 for all 853 observedhkl-reflexions.The iron of the tetrahedral layer is concentrated in one of the two crystallographically different kinds of tetrahedra. The basal oxygen rings of the tetrahedral layer form approximate hexagons and have not the ditrigonal configuration of the common micas. This peculiarity is considered to be a consequence of the size and charge of the barium ion. The role of OH in the common micas is played partly by S2– and Cl– in anandite.
Die Kristallstruktur des 2 O Sprödglimmers Anandit
Zusammenfassung Anandit hat die ungefähre Formel Ba(Fe3+, Fe2+)3[Si2(Fe3+, Fe2+, Si)2O10–x(OH)x] (S, Cl) (OH) mitx=0–1 und gehört zur 2O Sprödglimmergruppe. Er ist rhombisch; RaumgruppePnmn; a=5,468(9) Å,b=9,489(18) Å,c=19,963(11) Å;Z=4.Die Struktur wurde aus Weissenberg-Daten bestimmt, wobei mit einer approximativen Struktur in der PseudoraumpruppeCcmm begonnen wurde. Die Verfeinerung nach der Methode der kleinsten Quadrate führte für 409 photometrierte Reflexe aufR=0,061 und für alle 853 beobachtetenhkl-Reflexe aufR=0,131.Der Eisengehalt der Tetraederschicht ist in einer der beiden kristallographisch verschiedenen Tetraederarten konzentriert. Die basalen Sauerstoffringe der Tetraederschicht bilden annäherungsweise Sechsecke und haben nicht die ditrigonale Konfiguration der gewöhnlichen Glimmer. In Anandit spielen S2– und Cl– teilweise die Rolle der Hydroxylgruppen in den gewöhnlichen Glimmern.

With 4 Figures  相似文献   

20.
Hydrothermal experiments were conducted to evaluate the kinetics of H2(aq) oxidation in the homogeneous H2-O2-H2O system at conditions reflecting subsurface/near-seafloor hydrothermal environments (55-250 °C and 242-497 bar). The kinetics of the water-forming reaction that controls the fundamental equilibrium between dissolved H2(aq) and O2(aq), are expected to impose significant constraints on the redox gradients that develop when mixing occurs between oxygenated seawater and high-temperature anoxic vent fluid at near-seafloor conditions. Experimental data indicate that, indeed, the kinetics of H2(aq)-O2(aq) equilibrium become slower with decreasing temperature, allowing excess H2(aq) to remain in solution. Sluggish reaction rates of H2(aq) oxidation suggest that active microbial populations in near-seafloor and subsurface environments could potentially utilize both H2(aq) and O2(aq), even at temperatures lower than 40 °C due to H2(aq) persistence in the seawater/vent fluid mixtures. For these H2-O2 disequilibrium conditions, redox gradients along the seawater/hydrothermal fluid mixing interface are not sharp and microbially-mediated H2(aq) oxidation coupled with a lack of other electron acceptors (e.g. nitrate) could provide an important energy source available at low-temperature diffuse flow vent sites.More importantly, when H2(aq)-O2(aq) disequilibrium conditions apply, formation of metastable hydrogen peroxide is observed. The yield of H2O2(aq) synthesis appears to be enhanced under conditions of elevated H2(aq)/O2(aq) molar ratios that correspond to abundant H2(aq) concentrations. Formation of metastable H2O2 is expected to affect the distribution of dissolved organic carbon (DOC) owing to the existence of an additional strong oxidizing agent. Oxidation of magnetite and/or Fe++ by hydrogen peroxide could also induce formation of metastable hydroxyl radicals (•OH) through Fenton-type reactions, further broadening the implications of hydrogen peroxide in hydrothermal environments.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号