首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 15 毫秒
1.
The qualities of a laser diffraction grain size analyser, the Coulter LS-100 (range claimed by the manufacturer: 0·4–900 μm in a single measurement), are evaluated on sediments of fluvial and lacustrine origin. Accuracy and resolution of measurement on standard latex spheres are excellent. Reproducibility of the results on natural sediments appears to be satisfactory, but the method underestimates the fraction of clay particles with an efficiency of detection (36–70%) proportional to the clay content determined from pipette analysis. This efficiency is somewhat higher than those reported from other instruments of the same generation. Comparison of the Coulter LS-100 with other sizing techniques shows good agreement with the sieving method but some differences appear with the electroresistance particle technique: median and mean size values measured by the Coulter Counter TA1 are systematically lower than those obtained by the Coulter LS-100. Analyses show good correlation with those of a Malvern Laser particle analyser but a discrepancy appears with very fine silt and clay sized sediments. The Coulter LS-100 detects a higher clay content than that measured with the Malvern Laser Sizer 2600. Except when precise measurements of clay content are needed, the Coulter LS-100 produces precise and accurate results in size ranges required for geological and environmental studies.  相似文献   

2.
Classically, the grain size of soil and sediment samples is determined by the sieve method for the coarse fractions and by the pipette method, based on the ‘Stokes’ sedimentation rates, for the fine fractions. Results from the two methods are compared with results from laser diffraction size analysis, which is based on the forward scattering of monochromatic coherent light. From a point of view of laboratory efficiency, the laser sizing technique is far superior. Accuracy and reproducibility are shown by measurements on certified materials. It appears that laser grain size measurements of certified materials correspond very well with the certificated measurements. Tests were also done on a set of randomly selected sediments of fluvial, aeolian and lacustrine origin. Except for the (<2 μm) clay fraction, there is a coarsening of the mean diameter of one to two size classes (0.25 ?), caused by the non-sphericity of the particles. The platy form of the clay particles induces considerable differences (eight size classes) between pipette and laser measurements: the <2 μm grain size, defined by the pipette method corresponds with a grain size of 8 μm defined by the Laser Particle Sizer for the studied sediments. Using a higher grain size level for the clay fraction, when laser analysis is applied, enables workers in the geological and environmental field to compare classical pipette analysis with a laser sizing technique.  相似文献   

3.
Siliciclastic intervals in Lower Permian carbonate–siliciclastic cyclothems in western Kansas record climate control on facies progression, deposition and preservation. The 26 000 km2 study area comprises seven marine‐continental (carbonate–siliciclastic) cyclothems caused by glacioeustasy. Core data and a three‐dimensional geological model provide a detailed view of the sub‐surface on a gently sloping ramp. Siliciclastic intervals in the cyclothems are fine‐grained red beds with extensive pedogenic features, indicating a continental origin. Bed geometry (sheet‐like deposits that thin to the east), lateral grading, grain size (very fine‐grained sand to silt) and grain angularity (sub‐angular to angular) suggest that the sediment is loess sourced from the west, probably the Ancestral Rocky Mountains. There is a repeated record of glacial‐cycle‐scale, climate‐controlled cyclicity within siliciclastic intervals that has not been recognized previously. Aeolian silt grain size coarsens upward towards the middle, then fines upward in each siliciclastic interval. When sea‐level was high (interglacial) and carbonate production flourished, aeolian sedimentation nearly ceased, suggesting increased vegetation and rainfall at the source. As sea‐level fell, fine‐grained siliciclastic sediments were deposited under relatively dry, but seasonally wet conditions on an exposed ramp. Laterally graded coarser grained siliciclastic sediments with diagnostic fabrics indicate drier conditions with seasonal rainfall during a continued relative fall in sea‐level. The coarsest siliciclastic sediments were deposited during the lowest sea‐level and driest conditions, but still with sufficient seasonal moisture to allow vegetative cover and bioturbation. Subsequent upward fining is correlated with sedimentological indications of wetter conditions during relative sea‐level rise. Unlike common sequence stratigraphic models that relate siliciclastic sediment accumulation to base‐level rise, continental deposits were preserved because plants and pedogenesis stabilized aeolian sediment. The aggradational landscape formed by this process had several metres of positive relief that reduced accommodation for overlying marine carbonate strata. Thus, this mechanism for continental siliciclastic aggradation has a significant effect on sequence stratigraphic architecture.  相似文献   

4.
It is widely recognized that lake sediment grain‐size distributions tend to be polymodal and consist of two or more grain‐size components. However, for specific cases, the genesis of each component usually is poorly understood. In this study, the grain‐size components of the surface sediments of Hulun Lake, Inner Mongolia, were partitioned using the log‐normal distribution function method and the relationship between the identity of each grain‐size component and the hydraulic condition of the lake was investigated in order to relate the constituent components to specific depositional processes in the lake. The data indicate that the modern clastic sediments of Hulun Lake contain six distinct unimodal grain‐size distributions representing six grain‐size components. Each of the components retains its identity including modal size, manner of transportation and environment of deposition, although the relative percentage varies with the hydraulic conditions throughout the lake. These components are specified from fine to coarse modes as long‐term suspension clay, offshore‐suspension fine silt and medium to coarse silt, and nearshore‐suspension fine sand, saltation medium sand and traction coarse sand. The percentage contribution of several grain‐size components interpreted as being indicative of nearshore environments is shown to be correlated negatively with water depth across the modern lake bed; this suggests that the proportion of these components in core data might be useful as a proxy for water depth. This possibility was tested using a sediment core from Hulun Lake where high percentages of the nearshore grain‐size components were found to be correlated with low regional precipitation reconstructed from the pollen profile of the same core. The coincidence of two independent proxies does not only demonstrate the validity of log‐normal distribution function in partitioning polymodal sediments but reveals the potential of lake sediment grain‐size components for the research of lake‐level fluctuations during the geological past.  相似文献   

5.
The terrigenous fraction of seabed sediments recovered along the north‐west African continental margin illustrates spatial variability in grain size attributed to different transport mechanisms. Three subpopulations are determined from the grain‐size analyses (n = 78) of the carbonate‐free silt fraction applying an end‐member modelling algorithm (G. J. Weltje, 1997). The two coarsest end‐members are interpreted as representing aeolian dust, and the fine‐grained end‐member is related to fluvial supply. The end‐member model thus allows aeolian fallout to be distinguished from fluvial‐sourced mud in this area. The relative contributions of the end‐members show distinct regional variations that can be related to different transport processes and pathways. Understanding present‐day sediment dispersal and mixing is important for a better understanding of older sedimentary records and palaeoclimate reconstructions in the region.  相似文献   

6.
Grain‐size distribution is a fundamental tool for interpreting sedimentary units within depositional systems. The techniques assessed in this study are commonly used to determine grain‐size distributions for sand‐dominated sediments. However, the degree of consistency and differences in interpretation when using a combination of grain‐size methods have not yet been assessed systematically for sand‐dominated fluvial sediments. Results obtained from laser diffraction, X‐ray attenuation and scanning electron microscopy grain‐size analysis techniques were compared with those obtained from the traditional sieve/hydrometer method. Scanning electron microscopy was shown to provide an inaccurate quantitative analysis of grain‐size distributions because of difficulties in obtaining representative samples for examination. The X‐ray attenuation method is unsuitable for sand‐dominated sediments because of its upper size range of only 300 μm. The consistently strong correlation between the laser diffraction results and the sieve/hydrometer results shows that these methods are comparable for sand‐dominated fluvial sediments. Provided that sample preparation is consistent, the latter two methods can be used together within a study of such sediments while maintaining a high degree of accuracy. These results indicate that data for sand‐dominated fluvial sediments gained from the long‐established sieve/hydrometer method can be compared with confidence to those obtained by modern studies using laser diffraction techniques.  相似文献   

7.
Most techniques for estimating settling velocities of natural particles have been developed for siliciclastic sediments. Therefore, to understand how these techniques apply to bioclastic environments, measured settling velocities of bioclastic sedimentary deposits sampled from a nearshore fringing reef in Western Australia were compared with settling velocities calculated using results from several common grain‐size analysis techniques (sieve, laser diffraction and image analysis) and established models. The effects of sediment density and shape were also examined using a range of density values and three different models of settling velocity. Sediment density was found to have a significant effect on calculated settling velocity, causing a range in normalized root‐mean‐square error of up to 28%, depending upon settling velocity model and grain‐size method. Accounting for particle shape reduced errors in predicted settling velocity by 3% to 6% and removed any velocity‐dependent bias, which is particularly important for the fastest settling fractions. When shape was accounted for and measured density was used, normalized root‐mean‐square errors were 4%, 10% and 18% for laser diffraction, sieve and image analysis, respectively. The results of this study show that established models of settling velocity that account for particle shape can be used to estimate settling velocity of irregularly shaped, sand‐sized bioclastic sediments from sieve, laser diffraction, or image analysis‐derived measures of grain size with a limited amount of error. Collectively, these findings will allow for grain‐size data measured with different methods to be accurately converted to settling velocity for comparison. This will facilitate greater understanding of the hydraulic properties of bioclastic sediment which can help to increase our general knowledge of sediment dynamics in these environments.  相似文献   

8.
Using a combination of particle size analysis, magnetic measurements, scanning electron microscopy and transmission electron microscopy imaging, this study shows that in a wide range of depositional environments, there is a strong link between particle size classes and magnetic response, especially below the upper limit of stable single domain magnetic behaviour. Ferrimagnetic grain assemblages dominated by stable single domain magnetosomes regularly have peak susceptibility and remanence values in coarser grades than do those containing finer‐grained, viscous and superparamagnetic secondary magnetic minerals formed during pedogenesis. This effect is despite the fact that there is a one to two orders of magnitude size difference between the particle size boundaries (at 1 or 2 μm) and key domain state transitions (mostly below 0·05 μm). The implications of these results are explored using samples spanning 22 Myr of loess accumulation on the Chinese Loess Plateau. The results from the loess sections, complemented by data from low‐temperature magnetic experiments, show that there are subtle distinctions in mean ferrimagnetic grain‐size between the Pleistocene and Miocene parts of the record, thus allowing more refined rock magnetic interpretations of the fine‐grained ferrimagnetic mineral assemblages arising from the effects of weathering, pedogenesis and possibly diagenesis in the sections studied.  相似文献   

9.
Modal changes in both gravel and sands occur because of unequal durability of some clastic materials to abrasion. Selective abrasion causes an elimination of undurable materials and a complimentary enrichment of competent components. The fluviatile Oligocene Noda Group, northeast Japan, consists of two formations that include both the competent and undurable clastics. Modal analyses of rhyolite‐ or chert‐rich sediments in both formations show that the amount of pebble‐ and granule‐size chert detritus is nearly constant, but the sand‐size chert fragments remarkably decrease with the decreasing grain size. The amount of rhyolite pebbles and the sands, however, is nearly unchangeable despite the variable clast size. Results of our study reveal that we need careful thoughts for a restricted size of sediments and the mode of fine‐grained detritus that include undurable chert sands tends to significantly underestimate the outcrop area of chert bedrocks in the provenance.  相似文献   

10.
Recent sedimentological and palynological research on subfossil Holocene banded sediments from the Severn Estuary Levels suggested seasonality of deposition, registered by variations in mineral grain‐size and pollen assemblages between different parts of the bands. Here we provide data that strengthen this interpretation from sampling of modern sediments and pollen deposition on an active mudflat and saltmarsh on the margin of the Severn Estuary, and comparison with a vegetation survey and contemporary records of climate, river and tidal regimes. The results of grain‐size analysis indicate deposition of comparatively coarse‐grained silts during the relatively cool and windy conditions of winter and comparatively fine‐grained sediments during relatively warm and calm summer months. Pollen analysis demonstrates the significance of long‐term storage of pollen grains and fern spores in the estuarine waterbody, superimposed on which seasonal variations in pollen inputs from local and regional vegetation remain detectable. Copyright © 2007 John Wiley & Sons, Ltd.  相似文献   

11.
  相似文献   

12.
This study examines the forcing mechanisms driving long‐term carbonate accumulation and preservation in lacustrine sediments in Lake Iznik (north‐western Turkey) since the last glacial. Currently, carbonates precipitate during summer from the alkaline water column, and the sediments preserve aragonite and calcite. Based on X‐ray diffraction data, carbonate accumulation has changed significantly and striking reversals in the abundance of the two carbonate polymorphs have occurred on a decadal time scale, during the last 31 ka cal bp . Different lines of evidence, such as grain size, organic matter and redox sensitive elements, indicate that reversals in carbonate polymorph abundance arise due to physical changes in the lacustrine setting, for example, water column depth and lake mixing. The aragonite concentrations are remarkably sensitive to climate, and exhibit millennial‐scale oscillations. Extending observations from modern lakes, the Iznik record shows that the aerobic decomposition of organic matter and sulphate reduction are also substantial factors in carbonate preservation over long time periods. Lower lake levels favour aragonite precipitation from supersaturated waters. Prolonged periods of stratification and, consequently, enhanced sulphate reduction favour aragonite preservation. In contrast, prolonged or repeated exposure of the sediment–water interface to oxygen results in in situ aerobic organic matter decomposition, eventually leading to carbonate dissolution. Notably, the Iznik sediment profile raises the hypothesis that different states of lacustrine mixing lead to selective preservation of different carbonate polymorphs. Thus, a change in the entire lake water chemistry is not strictly necessary to favour the preservation of one polymorph over another. Therefore, this investigation is a novel contribution to the carbon cycle in lacustrine systems.  相似文献   

13.
The microfabrics of folded quartz veins in fine‐grained high pressure–low temperature metamorphic greywackes of the Franciscan Subduction Complex at Pacheco Pass, California, were investigated by optical microscopy, scanning electron microscopy including electron backscatter diffraction, and transmission electron microscopy. The foliated host metagreywacke is deformed by dissolution–precipitation creep, as indicated by the shape preferred orientation of mica and clastic quartz without any signs of crystal‐plastic deformation. The absence of crystal‐plastic deformation of clastic quartz suggests that the flow stress in the host metagreywacke remained below a few tens of MPa at temperatures of 250–300 °C. In contrast, the microfabric of the folded quartz veins indicates deformation by dislocation creep accompanied by subgrain rotation recrystallization. For the small recrystallized grain size of ～8 ± 6 μm, paleopiezometers indicate differential stresses of a few hundred MPa. The stress concentration in the single phase quartz vein is interpreted to be due to its higher effective viscosity compared to the fine‐grained host metagreywacke deforming by dissolution–precipitation creep. The fold shape suggests a viscosity contrast of one to two orders of magnitude. Deformation by dissolution–precipitation creep is expected to be a continuous process. The same must hold for folding of the vein and deformation of the vein quartz by dislocation creep. The microfabric suggests dynamic recrystallization predominantly by subgrain rotation and only minor strain‐induced grain boundary migration, which requires low contrasts in dislocation density across high‐angle grain boundaries to be maintained during climb‐controlled creep at high differential stress. The record of quartz in these continuously deformed veins is characteristic and different from the record in metamorphic rocks exhumed in seismically active regions, where high‐stress deformation at similar temperatures is episodic and related to the seismic cycle.  相似文献   

14.
仝长亮  高抒 《沉积学报》2008,26(1):46-53
激光粒度仪的广泛应用带来了与历史数据的对比问题,因此需要建立激光粒度仪与早期分析结果之间的关系。根据江苏海岸潮滩沉积物样品的激光粒度仪和移液管-筛析法分析,对粒度参数、粒度组分等进行了对比,对两种方法的差异进行了分析。结果表明,对于江苏潮滩沉积物粒度参数中平均粒径的激光粒度仪与移液管-筛析分析结果之间有良好的线性关系;筛分法测得的粗颗粒物质较激光法偏少,而移液管法法测得的细颗粒物质较激光法偏多;将样品分类之后再进行两种方法所获粒度参数的回归分析,相关性得以提高,说明不同粒度组成的沉积物对分析结果的对比有不同的影响。两种方法之间的换算关系不仅与研究区域有关,而且与沉积物本身的粒度组成有关。  相似文献   

15.
The keels of icebergs and ice‐pressure ridges plough through unconsolidated sea/lake sediments gouging out long grooves known as ice keel scour marks. Although the surface and (more recently) subsurface morphology of scours are well‐documented, little is known of the effect of grain size on the detectability, style and intensity of sub‐scour deformation. This investigation macroscopically and microscopically (two‐dimensional thin sections) examines suspected ice keel scour in: (i) glaciolacustrine pebbly sandy mud and (ii) fine‐grained sands at Scarborough Bluffs, Ontario, Canada. In this investigation, there is an almost identical suite of deformation structures (individual structures and overprinted structural patterns) to those identified in iceberg‐scoured clays from former Glacial Lake Agassiz (Manitoba, Canada); this confirms that deformation in the pebbly sandy mud and fine‐grained sands at Scarborough Bluffs is likely to be indicative of ice keel scour. Discrete differences in the detectability, style and intensity of deformation between the Scarborough Bluffs and Glacial Lake Agassiz sediments are probably a function of grain size in response to ice keel scour. This research provides additional information on the types of structures that are associated with sediment deformation by processes of ice keel scour in a variety of grain sizes. This information is particularly valuable to inform palaeoenvironmental reconstruction and offshore engineering in areas where ice keel scour occurs in a variety of grain sizes. It also demonstrates the potential value of micromorphology where, for example, the study of cores is necessary.  相似文献   

16.
文章回顾了粒度分析的历史,总结了常用的粒径类型,介绍了粒度标准和目前沉积学中常用的5种粒度分析方法,并对其中的沉降法、场干扰分析法、图像法作了详细的分类说明。此外,对每一种粒度分析方法的适用范围、测定原理以及其存在的优缺点也进行了详细的介绍。其中：直接测量法简单易行,但精度较差;筛析法较为普遍,但只限于松散或弱胶结沉积物,且不能反映颗粒形状;沉降法适用于松散样、弱胶结样和液体样的分析,可对细砂、粉砂或泥等细粒沉积物进行测量;场干扰法主要依据碎屑颗粒的衍射、散射及电压脉冲响应进行,固体样和液体样均可,精度高,适用性广;图像法手段多样,简单直观,操作性强。总体上,未来的几十年内,粒度分析方法仍将是新旧技术并存,多种方法共用的状况。  相似文献   

17.
采用LS13320型的激光衍射粒度分析仪对金远洞洞穴堆积物进行粒度分析,所测得的数据用Grapher软件绘制堆积物粒度频率曲线,计算粒度参数,以此来研究金远洞更新世洞穴红色堆积物的粒度特征并推断沉积环境.金远洞洞穴堆积物粒度组成中,粉砂含量最高,为优势粒组,平均值为50.14%,其中细粉砂含量高于粗粉砂含量;黏粒含量次之,砂含量最少.样品粒度频率呈多峰态.通过粒度参数计算,推测洞穴红色堆积物的沉积环境以风力沉积为主,后经流水搬运,但堆积物的组成未发生明显变化,反映了搬运的水动力较弱.物质来源主要受气候的影响,环境干冷时以近源沉积为主,环境温暖湿润时以远源沉积为主.  相似文献   

18.
The abundance and morphology of microdiamond in dolomite marble from Kumdy‐kol in the Kokchetav Massif, are unusual; a previous study estimated the maximum content of diamonds in dolomite marble to be about 2700 carat ton?1. Microdiamond is included primarily in garnet, and occasionally in diopside and phlogopite pseudomorphs after garnet. They are classified into three types on the basis of their morphology: (1) S‐type: star‐shaped diamond consisting of translucent cores and transparent subhedral to euhedral very fine‐grained outer parts; (2) R‐type: translucent crystals with rugged surfaces; and (3) T‐type: transparent, very fine‐grained crystals. The S‐type is the most abundant. Micro‐Laue diffraction using a 1.6‐µm X‐ray beam‐size demonstrated that the cores of the star‐shaped microdiamond represent single crystals. In contrast, the most fine‐grained outer parts usually have different orientations compared to the core. Laser–Raman studies indicate that the FWHM (Full Width at Half Maximum) of the Raman band of the core of the S‐type diamond is slightly larger than that for the outer parts. Differences in morphology, crystal orientations, and in the FWHM of the Raman band between the core and the fine‐grained outer‐parts of S‐type microdiamond suggest that the star‐shaped microdiamond was formed discontinuously in two distinct stages.  相似文献   

19.
Laser diffraction is now widely used for particle size distribution analysis of sediments and soils. The technique can be very precise, and offers advantages of speed and cost over many other methods when used to analyse mixtures of sand, silt and clay. This study presents the results of an experimental investigation that examined the sensitivity of the Beckman-Coulter LS230 instrument to mixtures of different grain populations and differences in particle shape. The instrument was found to have high sensitivity to coarse particles in a finer matrix (detection threshold 1–2%), but much lower sensitivity to finer particles in a coarser mixture (detection threshold 12–17%). Experiments using near-spherical ballotini showed that laser analysis provides very similar values to dry sieving for the mean, median and mode, but for a range of natural sand samples values for the mean, median and mode were offset by 8–21%, with an average of ca 15%, compared with sieving. Analysis using a Beckman-Coulter RapidVUE instrument, which provides both size and shape information, provided support for the hypothesis that the differences between laser analysis and sieving are partly attributable to the effects of particle shape. However, an additional factor is the way in which the laser software interprets the optical diffraction data. The software predicts a high degree of log-normality in the size distribution, such that highly skewed, truncated or bimodal samples are poorly represented. Experiments using sieved fractions of ballotini indicated that, even with near-perfectly spherical particles, the particle size distribution predicted by the laser software includes a relatively large percentage of particles outside the sieve class limits.  相似文献   

20.
A 2.73 m long sediment sequence from Loon Lake, located at 18 m a.s.l. on outer Geographical Society Ø, East Greenland, was investigated for its chronology and changes in physical and biogeochemical properties, macrofossils, and grain‐size distribution. The predominance of marine fossils throughout the sequence, dated by 14C AMS to between 8630 and 7535 cal. yr BP, shows that the Loon Lake at that time was a marine basin, which according to existing sea‐level curves was about 15–35 m deep. The sequence mainly consists of fine grained homogeneous sediments, which are interrupted by a 0.72 m thick sandy horizon with erosive basis and distinct fluctuations in the grain‐size distribution and in the physical and biogeochemical properties. According to the radiocarbon dates, this sandy horizon was deposited after 8500–8300 cal. yr BP and is interpreted as originating from the Storegga tsunami. The record from Loon Lake provides the first indication of Storegga tsunami deposits from East Greenland. Copyright © 2006 John Wiley & Sons, Ltd.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号