共查询到20条相似文献，搜索用时 15 毫秒
1.
含水层参数对于定性分析区域地下水资源评价、数值模拟及预报、开发利用与保护及科学管理具有重要意义,而江汉平原水文地质参数求解的研究却相对较少.2015年江汉平原1:50 000水文地质调查项目完成杨林尾图幅与陆溪口图幅,选择杨林尾图幅和陆溪口图幅中的4个代表性钻孔,分别做了3组抽水试验和一组压水试验.对抽水数据使用Dupuit公式法结合抽水稳定阶段数据求解含水层参数,同时利用Aquifer Test软件中Theis标准曲线法、直线图解法对抽水试验中非稳定条件下抽水数据对含水层参数求解,得到孔隙水含水层渗透系数及弹性给水度;利用压水试验工程规范求解基岩裂隙含水层的渗透系数.探讨了利用非稳定抽水试验条件下求解含水层参数方法的可行性及该方法的优势.计算结果表明:杨林尾镇浅层(20.2~64.55 m)含水层渗透系数为0.075 m/d,弹性给水度为5.8×10-2;深层(138~160 m)含水层渗透系数为9.89 m/d,弹性给水度为2.3×10-5;陆溪口镇浅层(19.4~36.4 m)含水层渗透系数1.26 m/d,弹性给水度为1.1×10-1;基岩渗透系数为0.012 m/d.通过结果对比分析发现对于单孔非稳定抽水试验,对前期水位降深数据筛选分析,同样可以利用非稳定井流理论反演含水层参数,结果比较可靠. 相似文献
2.
Theis模型、Dupuit模型等经典井流模型分析非均质含水层井流试验数据有一定的局限性,获取的参数不适合表征非均质含水层特性。而GRF模型可以获取含水层流动特性的数据。相比于Theis模型、Dupuit模型,GRF模型更能表征非均质含水层特性。以黄石东湖新村棋盘洲长江大桥的抽水试验数据为例,采用Theis模型和GRF模型计算含水层渗透系数,结合实际水文地质条件,对比分析不同方法计算的水文地质参数,并计算含水层水流维数和表观压力传导系数（Kf /Ssf）。结果表明:研究区含水层为细砂夹条带状黏土透镜体的非均质含水层,采用GRF模型计算结果更符合实际情况,渗透系数为 4.09×10?3cm/s;含水层水流维数为1.61,地下水为双线性流动状态,含水层对抽水试验的响应主要受黏土条带控制;观测井和抽水主井的Kf /Ssf呈非线性相关,进一步验证了含水层的非均质性。在非均质孔隙含水层中,应用多孔联合非稳定GRF井流试验方法不仅能确定水文地质参数,并且能丰富对含水层特性的认知。 相似文献
3.
4.
Field and laboratory methods have been used to determine the hydraulic properties in a multiple-layer aquifer–aquitard system that is hydrologically connected to a river. First, hypothetical pumping tests in aquifer–aquitard systems were performed to evaluate the feasibility of MODFLOW-PEST in determining these parameters. Sensitivity analyses showed that: the horizontal hydraulic conductivity in the aquifer has the highest composite sensitivity; the vertical hydraulic conductivity has higher composite sensitivity than the horizontal hydraulic conductivity in the aquitard; and a partial penetration pumping well in an aquifer layer can improve the quality of the estimated parameters. This inverse approach was then used to analyze a pumping-recovery test conducted near the Platte River in southeastern Nebraska, USA. The hydraulic conductivities and specific yield were calculated for the aquitard and aquifer. The direct-push technique was used to generate sediment columns; permeameter tests on these columns produced the vertical hydraulic conductivities that are compatible with those obtained from the pumping-recovery test. Thus, the combination of the direct-push technique with permeameter tests provides a new method for estimation of vertical hydraulic conductivity. The hydraulic conductivity, determined from grain-size analysis, is smaller than the horizontal one but larger than the vertical one determined by the pumping-recovery test. 相似文献
5.
在地下水资源评价理论方面, 陈崇希教授分析了"平均布井法"不符合质量守衡原理的实质, 纠正了以"地下水补给量计算可持续开采量"的错误, 提出了基于"质量守衡"的地下水资源评价原则, 强调分析"补给的增加量与排泄的减少量"在评价地下水可持续开采量时的重要意义.在地下水动力学领域, 陈崇希教授纠正了稳定井流"影响半径"模型的错误, 恢复了Dupuit"圆岛模型"的原貌, 拓展了Theis公式和Hantush公式的应用条件, 改进了地下水非稳定井流理论, 完善了其中的某些基本概念.在水文地质模拟仿真技术方面, 陈崇希教授提出确定滨海承压含水层海底边界的理论和方法; 提出地下水混合井流的模型和模拟方法, 解决了混合抽水试验确定分层水文地质参数的难题; 提出岩溶管道-裂隙-孔隙三重介质的地下水线性-非线性流动的模型; 建立了考虑井管水流雷诺数对滤管入流量分布的水平井-含水层系统的地下水流模型; 完成了"渗流-管流耦合模型"的砂槽物理模拟, 并用数值方法仿真了地下水流的规律; 最近向观测孔水位形成的传统观念———常规观测孔中的水头降深反映该孔滤水管中各点的平均降深———提出质疑.陈崇希教授建立的"渗流-管流耦合模型"使传统的基于线汇/线源的井孔-含水系统模型提高到新的水平.陈崇希教授积极倡导"防止模拟失真, 提高仿真性", 强调精细地分析水文地质条件、合理地概化模型和采用正确的仿真技术的重要性. 相似文献
6.
陈崇希 《水文地质工程地质》2020,47(5):1-4
Dupuit（1863年）提出的模型是“圆岛状含水层稳定井流模型”,这个模型只有侧向湖海边界条件,而不涉及上边界降水入渗补给条件。因此,Dupuit模型只能在旱季用于地下水井流试验求取含水系统的参数,而不能够用于预测。文章发展Dupuit潜水井流模型,考虑地面均匀稳定入渗补给（蒸发排泄示为其负值）作用。以质量守衡原理为基础,假定渗流服从Darcy定律并满足Dupuit徦定,建立极坐标下的地下水流微分方程,再依边界条件建立相应的流量方程和水位方程。这些方程为具地面入渗补给条件下井流试验求取水文地质参数以及预测相应条件下地下水抽水的效果,提供了基础条件。讨论了引入Dupuit假定对本问题解析研究可以降维（略去z变量）带来好处的同时,在地下水分水岭附近及抽水井附近可能出现偏离Dupuit假定,建议在抽水试验求取含水层参数时,观测孔的部署要尽量回避这些区段。 相似文献
7.
8.
Field observation and numerical simulations were carried out to evaluate the hydraulic relationship between the shallow and deep aquifer of a High Plains Aquifer system, in which shallow and deep aquifers are separated by an aquitard. Pumping from the lower aquifer resulted in a small drawdown in the upper aquifer and a larger drawdown in the aquitard; pumping from the shallow aquifer caused a small drawdown in the aquitard and the deep aquifer. Analysis of pumping test data gives the values of the hydraulic conductivity of the aquitard and the deep aquifer. Long-term observation of groundwater levels in the shallow and deep aquifers showed that a strong downward hydraulic gradient was maintained during an irrigation season. Numerical simulations were used to calculate the induced leakage of water from the shallow to the deep aquifer. Water budget analyses suggested that after pumping continues for a couple of days, the leakage from the overlying layers begins to supply the majority of the withdrawal from the deep aquifer. However, the induced leakage from the upper shallow aquifer can travel only a few meters into the aquitard, and it can not reach the lower aquifer during a 90 day pumping period. The major portion of the induced leakage occurred during the pumping period, but a small leakage can continue as a residual effect after the pumping period. The vertical hydraulic conductivity of the aquitard plays a major role in partitioning the ratio of the induced leakage for the pumping and after-pumping periods. 相似文献
9.
水文地质参数的计算是水文地质勘察的一个重要环节。根据在塔城市北东方向喀拉墩地区进行的抽水试验资料,分别采用Aquifer Test软件和Dupuit公式迭代法计算抽水试验参数,对所求取的参数进行对比分析,通过Aquifer Test软件求取的参数与Dupuit公式迭代法求取的参数相近,各参数偏差率低,最终通过抽水试验数据,经不同的方法计算,确定含水层渗透系数K值为31.14 m/d。 相似文献
10.
Evaluation of a pumping test of the Snake River Plain aquifer using axial-flow numerical modeling 总被引：1，自引：1，他引：1
The Snake River Plain aquifer in southeast Idaho is hosted in a thick sequence of layered basalts and interbedded sediments.
The degree to which the layering impedes vertical flow has not been well understood, yet is a feature that may exert a substantial
control on the movement of contaminants. An axial-flow numerical model, RADFLOW, was calibrated to pumping test data collected
by a straddle-packer system deployed at 23 depth intervals in four observation wells to evaluate conceptual models and estimate
properties of the Snake River Plain aquifer at the Idaho National Engineering and Environmental Laboratory. A delayed water-table
response observed in intervals beneath a sediment interbed was best reproduced with a three-layer simulation. The results
demonstrate the hydraulic significance of this interbed as a semi-confining layer. Vertical hydraulic conductivity of the
sediment interbed was estimated to be about three orders of magnitude less than vertical hydraulic conductivity of the lower
basalt and upper basalt units. The numerical model was capable of representing aquifer conceptual models that could not be
represented with any single analytical technique. The model proved to be a useful tool for evaluating alternative conceptual
models and estimating aquifer properties in this application.
Electronic Publication 相似文献
11.
Allen P. Macfarlane Andrea Förster Daniel F. Merriam Jörg Schrötter John M. Healey 《Hydrogeology Journal》2002,10(6):662-673
Aquifer properties can be evaluated by monitoring artificially stimulated fluid movements between wells, if the fluid is
heated. Changes in the temperature profile recorded in observation wells indicate the flow path of the heated fluid, which
in effect acts as a tracer. A fluid-flow experiment in the Cretaceous Dakota Formation at the Hodgeman County site, west-central
Kansas, demonstrated the advantage of using the distributed optical-fiber temperature sensing method for monitoring transient
temperature conditions in this hydrological application. The fluid flow in the aquifer was increased by producing water from
a pumping well and injecting heated water in an injection well 13 m (43 ft) distant from the pumping well. The time-temperature
series data obtained and compared with results from previous pumping tests point to interwell heterogeneity of the aquifer
and to a zone in the sandstone aquifer of high hydraulic conductivity. However, the experiment would have allowed further
clarification of aquifer heterogeneity and thermal properties if at least one observation well had been present between the
injection and production wells.
Electronic Publication 相似文献
12.
13.
含水层非均质性空间分布特征的识别,是准确模拟地下水流和污染物运移的前提.基于室内非均质含水层砂箱实验,分别利用水力层析法和克立金插值法刻画了非均质含水层渗透系数场.研究结果表明:(1) 水力层析法与克立金法相比,不仅可以更好地刻画非均质含水层渗透系数场,还可以更高精度地预测地下水流过程;(2) 水力层析抽水实验中,通过增加抽水实验组数可以有效地提高水力层析参数反演的精度,但是抽水实验组数增加到一定程度以后,再增加抽水组数不会显著提升参数反演的效果.后续需要进一步研究水力层析抽水实验合适的组数,进一步对抽水井进行优化布设. 相似文献
14.
Estimating the hydraulic properties of fractured aquifers is challenging due to the complexity of structural discontinuities that can generally be measured at a small scale, either in core or in outcrop, but influence groundwater flow over a range of scales. This modeling study uses fracture scanline data obtained from surface bedrock exposures to derive estimates of permeability that can be used to represent the fractured rock matrix within regional scale flow models. The model is developed using PETREL, which traditionally benefits from high resolution data sets obtained during oil and gas exploration, including for example seismic data, and borehole logging data (both lithological and geophysical). The technique consists of interpreting scanline fracture data, and using these data to generate representative Discrete Fracture Network (DFN) models for each field set. The DFN models are then upscaled to provide an effective hydraulic conductivity tensor that represents the fractured rock matrix. For each field site, the upscaled hydraulic conductivities are compared with estimates derived from pumping tests to validate the model. A hydraulic conductivity field is generated for the study region that captures the spatial variability of fracture networks in pseudo-three dimensions from scanline data. Hydraulic conductivities estimated using this approach compare well with those estimated from pumping test data. The study results suggest that such an approach may be feasible for taking small scale fracture data and upscaling these to represent the aquifer matrix hydraulic properties needed for regional groundwater modeling. 相似文献
15.
由含水层底部向上施工疏放水孔（井）进行疏水降压是保证煤矿安全开采的重要措施之一,该类疏放水孔与地面抽水井的渗流特征具有显著差别。为了研究井下疏放水孔的渗流特征,以非承压含水层底部单井疏放水孔为例,采用数值模拟的方法对其渗流特征进行研究。研究结果表明,当疏放水井的井长lw小于临界长度lc时,即lwc,疏放水井上部含水层孔隙水压力大于0,且由下而上呈先增加后减小的分布规律,渗流量与井长呈指数函数关系增加;当lw ≥ lc时,疏放水非完整井的渗流特征及渗流量与完整井相同;渗流量随井半径增加呈指数关系增加,且指数小于1;将s+lw代替水位降深s对裘布依（Dupuit）潜水完整井计算公式进行修正,当lwc时,采用修正的Dupuit潜水完整井计算公式计算疏放水非完整井渗流量更精确。该研究结果对认识井下疏放水井上部孔隙水压力分布特征及合理布置疏放水井具有重要的借鉴意义。 相似文献
16.
在地下水扩散方程中,压力传导系数是描述地下水运动的重要参数。传统的方法是通过抽水或注水给地下水系统一个扰动,监测地下水水位的响应,由此计算含水层的压力传导系数。文章提出用潮汐衰减率方法识别含水层压力传导系数,其适用于滨海区承压含水层的参数识别。在推导出解析解的基础上,通过数值拟合、最小二乘法、牛顿迭代法求得含水层的压力传导系数,提出潮汐衰减率的概念,建立余切函数与潮汐衰减率的线性关系,用线性关系中的斜率和截距识别压力传导系数。用潮汐衰减率方法识别出的压力传导系数与其实际值相等,说明该方法是正确有效的。潮汐信号衰减率与海水振荡的余切函数线性相关。数值仿真表明,该方法可以准确地估算出含水层的压力传导系数。潮汐衰减率方法具有少打井,经济高效等优点。潮汐衰减率方法为实际工程应用提供了可靠的理论基础,它可以用于部分实际工程中。该方法的局限性在于需要提供含水层的部分参数,如含水层的长度、海水波动振幅、频率等。 相似文献
17.
Physical and hydraulic properties of sediment from two karst aquifers were measured to determine (1) the similarity of sediment
between karst aquifer systems and (2) the importance of sediment in modeling flow through karst aquifers. The sediment from
the two systems was similar in size and composition. Within both aquifers, the silt-sized sediment was composed primarily
of quartz, with minor amounts of plagioclase and clays. Hydraulic conductivity of the sediment measured directly (falling-head
test) ranged from 1.61×10−7 to 1.33×10−6 m s–1 and estimated using the Campbell equation ranged from 8.30×10−8 to 8.98×10−7 m s–1. These values of hydraulic conductivity fall within the span of hydraulic conductivities for carbonate rocks, indicating
that the sediment and carbonate matrix could be represented as one mathematical unit in modeling flow through karst aquifers.
Statistical agreement in the hydraulic conductivity values generated by the two methods indicates that the estimation technique
could be used to calculate hydraulic conductivities; thus allowing karst scientist to collect bulk sediment samples instead
of having to collect cores from within karst aquifers.
Electronic Publication 相似文献
18.
Fatoumata Barry Duke Ophori Jeffrey Hoffman Robert Canace 《Environmental Geology》2009,56(8):1593-1603
Delineating capture zones of pumping wells is an important part of safe drinking water and well protection programs. Capture
zones or contributing areas of a groundwater extraction well are the parts of the aquifer recharge areas from which the wells
draw their water. Their extent and location depend on the hydrogeologic conditions such as groundwater recharge, pumping scenario
and the aquifer properties such as hydraulic conductivity, porosity, heterogeneity of the medium and hydraulic gradient. Different
methods of delineation can be used depending on the complexity of the hydrogeologic conditions. In this study, a 3-dimensional
transient numerical MODFLOW model was developed for the Central Passaic River Basin (CPRB), and used with a MODPATH particle
tracking code to determine 3-dimensional transient capture zones. Analytically calculated capture zones from previous studies
at the site were compared with the new numerically simulated capture zones. The study results revealed that the analytical
solution was more conservative, estimating larger capture zones than the numerical models. Of all the parameters that can
impact the size, shape and location of a capture zone, the hydraulic conductivity is one of the most critical. Capture zones
tend to be smaller in lower hydraulic conductivity areas. 相似文献
19.
Evaluation of unconfined aquifer parameters from flow to partially penetrating wells in Tailan River basin, China 总被引：1，自引：1，他引：0
Emmanuel Kwame Appiah-Adjei Longcang Shu Kwaku Amaning Adjei Minjing Deng Xiaohui Wang 《Environmental Earth Sciences》2013,69(3):799-809
Effective evaluation, management and abstraction of groundwater resources of any aquifer require accurate and reliable estimates of its hydraulic parameters. This study, therefore, looks at the determination of hydraulic parameters of an unconfined aquifer using both analytical and numerical approaches. A long-duration pumping test data obtained from an unconfined aquifer system within the Tailan River basin in Xinjiang Autonomous Region in the northwest of China is used, in this study, to investigate the best method for estimating the parameters of the aquifer. The pumping test was conducted by pumping from a radial collector well and measuring the response in nine observation wells; all the wells used in the test were partially penetrating. Using two well-known tools, namely AquiferTest and MODFLOW, as an aid for the analytical and numerical approaches, respectively, the parameters of the aquifer were determined and their outputs compared. The estimated horizontal hydraulic conductivity, vertical hydraulic conductivity, and specific yield for the analytical approach are 38.1–50.30 m/day, 3.02–9.05 m/day and 0.204–0.339, respectively, while the corresponding numerical estimates are 20.50–35.24 m/day, 0.10–3.40 m/day, and 0.27–0.31, respectively. Comparing the two, the numerical estimates were found to be more representative of the aquifer in the study area since it simulated the groundwater flow conditions of the pumping test in the aquifer system better than the analytical solution. 相似文献
20.
Oscillatory Pumping Test to Estimate Aquifer Hydraulic Parameters in a Bayesian Geostatistical Framework 总被引：1，自引：0，他引：1
Comprehensive information about the spatial distribution of the subsurface hydraulic properties is crucial to model groundwater flow, to predict solute transport in aquifers and to design remediation actions. In this work, a Bayesian Geostatistical approach, as implemented in bgaPEST, was adopted to estimate the hydraulic properties of a well field located at the Campus of Science and Technology of the University of Parma (Northern Italy), in a contest of a highly parameterized inversion. Head data, collected by means of multi frequency oscillatory pumping tests, were used to both estimate the hydraulic parameters and validate the results. The groundwater flow processes were modelled by means of MODFLOW 2005 and an adjoint-state formulation of the same software was used to efficiently calculate the sensitivity matrix, required by the inverse procedure. The Bayesian Geostatistical approach estimated the hydraulic conductivity and specific storage fields, handling a large number of parameters. The results of the inversion are consistent with the alluvial nature of the investigated aquifer and the preliminary traditional pumping tests carried out at the site. 相似文献