共查询到17条相似文献，搜索用时 171 毫秒
1.
为探究边壁双曲率对其水动力特性的影响，应用RNG k-ε紊流模型和部分面积体积障碍模拟技术（FAVOR），针对圆管非满流建立三维数值模型，通过物理模型试验结果验证该数值模型的可行性。针对底坡和充满度不同组合条件进行数值试验，分析断面流速、壁面切应力和雷诺切应力分布规律等。研究结果表明：圆管非满流断面上不同垂线的流速分布具有较好的相似性，据此提出了垂线流速分布的抛物线公式；针对不同充满度条件提出了壁面切应力沿湿周分布的统一表达式；雷诺切应力沿垂线服从线性分布规律，充满度越大且距中垂线越远，沿垂线的变化梯度越小；当充满度大于0.5时，由于受二次流影响断面中垂线上雷诺切应力出现负值。 相似文献
2.
为了探索宽窄相间河道的水流紊动特性，以西南地区宝兴河上游宽窄相间河段为研究对象，基于室内概化模型试验，采用多普勒声学流速仪（ADV）测量了室内模型典型断面上的三维瞬时流速，分析典型断面上的纵向时均流速、紊动强度、雷诺切应力和紊动能的分布规律。试验结果显示：宽窄相间水槽中，扩散段边壁的紊动强度大于中心区域的紊动强度，最大值位于0.2倍水深处；扩散段两侧坡脚处紊动能最大；侧壁区的平面和立面雷诺切应力最大值出现在扩散段内，中心区域最大雷诺切应力位于两槽间的中间断面处；扩散段内水流紊乱，两侧出现旋涡和涡脱，易造成侧壁侵蚀加强，引起河道拓宽。深入分析了宽窄相间河道水流的紊动特性，可为山区河流治理和自然灾害防治提供参考。 相似文献
3.
4.
为了探索宽窄相间河道的水流紊动特性,以西南地区宝兴河上游宽窄相间河段为研究对象,基于室内概化模型试验,采用多普勒声学流速仪(ADV)测量了室内模型典型断面上的三维瞬时流速,分析典型断面上的纵向时均流速、紊动强度、雷诺切应力和紊动能的分布规律。试验结果显示:宽窄相间水槽中,扩散段边壁的紊动强度大于中心区域的紊动强度,最大值位于0.2倍水深处;扩散段两侧坡脚处紊动能最大;侧壁区的平面和立面雷诺切应力最大值出现在扩散段内,中心区域最大雷诺切应力位于两槽间的中间断面处;扩散段内水流紊乱,两侧出现旋涡和涡脱,易造成侧壁侵蚀加强,引起河道拓宽。深入分析了宽窄相间河道水流的紊动特性,可为山区河流治理和自然灾害防治提供参考。 相似文献
5.
6.
7.
8.
采用Naot-Rodi代数应力模型(N-R模型),结合非均匀交错网格下的混合有限分析法(HFAM)来计算漫滩水流的三维流动。为了得到稳定的收敛解,作了两点改进:其一为非均匀网格中数值离散的导数项二阶格式的引入;其二为复式断面分块耦合技术的采用。给出了漫滩水流主流速等值线、二次流的断面分布、垂线平均流速的横向分布以及主槽与全断面流量比随相对水深的变化规律。部分结果与实验资料的对比,表明NR模型和HFAM能较好地用于研究漫滩水流流速、流量和水位的关系。 相似文献
9.
淹没刚性植被通过改变水流结构,造成时均流速、紊动强度、雷诺应力等水力参数垂线分布不均匀和沿程差异化。采用声学多普勒测速仪(ADV)测量3种淹没度(3.0、4.0、5.0)下的流速,结合统计学方法,系统分析植被段内及其上、下游过渡段流速和紊动特性差异。结果表明：植被显著增强了水流紊动,且紊动特性取值与淹没度正相关;植被段内流速差异在低淹没度下的植被层内和高淹没度下的自由流动层内更加显著,而紊动特性沿程增强,且垂线分布具有相似性,最大值点位于冠层顶部附近;当淹没度满足KH涡的形成和发展条件时,随淹没度的增大,植被段内紊动特性垂线分布出现转折点(临近此点梯度急剧减小并趋于0)的断面数量增多,经验证,在充分发展的紊流区此点可作为KH涡的上边界点。 相似文献
10.
受地形、地质等条件影响,明渠收缩过渡段在输水工程中十分常见,过渡段长度过短,会导致水面波动,水体紊动加剧。为研究明渠不同长度过渡段内纵向时均流速及紊动强度的分布规律,通过室内模型试验,利用二维电磁流速仪ACM2-RS测量了渠道内沿程中垂线不同深度处瞬时流速。试验结果表明:收缩段内,纵向时均流速沿程增加,紊动强度沿程降低,遵循涡旋的拉伸机制和线性扭曲理论;受二次流影响,最大流速位于水面以下,且最大流速的位置随二次流作用的增强而降低;不同长度过渡段对下游纵向流速分布和紊动强度影响不同,过渡段越短,下游水流紊动越强,但非渠底附近紊动强度沿垂向先减后增的规律不变。 相似文献
11.
利用自主研发的煤岩剪切?渗流耦合试验装置,开展不同充填度下含结构面砂岩相似材料剪切?渗流耦合特性试验研究。结果表明：（1）在恒定水压情况下,充填度越大,相似材料的峰值剪应力越小,法向位移越大且发生剪缩现象,一定充填度范围内流量峰值也越大;（2）剪切过程中流量变化主要受充填物中产生的裂隙控制,剪切位移越大,裂隙越发育,流量越大。法向位移对流量变化有一定影响,但随着充填度的增大,影响越来越小;（3）随充填度的增加,充填物的破碎程度逐渐增大。充填度较小时,其主要受到裂隙开度的控制;充填度较大时,主要受法向力影响。由于渗透水的软化作用,结构面的磨损程度逐渐减小。 相似文献
12.
为探究锚固节理在直剪加载作用下的细观力学响应,利用颗粒流数值计算方法建立不同锚固角度下的锚固节理数值模型,并进行不同法向荷载下的直剪试验。之后,通过分析和对比剪切-位移曲线和峰值剪切强度来对锚固节理宏观力学性质进行研究。与此同时,基于微裂纹分布规律,从细观角度揭示了剪切荷载下不同锚固角度的岩石节理面的破坏特征;研究结果显示。（1）不同于非锚固节理,锚固节理的剪切-位移曲线在剪切后期呈现出一定的增长趋势,且粗糙度不同曲线变化特征存在一定的差异。（2）不同锚固角度下,锚固节理的破坏模式存在着较为明显的差异。当锚固角为90°时,锚固节理模型的破坏主要集中于锚杆与上下节理面接触位置,且破坏主要为挤压式破坏。随着锚固角度的减小,接触位置的破碎区域不断减小,节理破坏主要表现为沿着锚杆的轴向拉伸变形破坏及内部的拉伸破坏。（3）锚固角度的变化对锚固节理的抗强度的影响程度与节理面的粗糙度存在一定关联。具体而言,较为平直节理抗剪强度随着锚固角度的增大,增长趋势明显,而粗糙节理面随着锚固角度的增大峰值抗剪强度的变化趋势相对较为平缓。 相似文献
13.
In this study,the fractal dimensions of velocity fluctuations and the Reynolds shear stresses propagation for flow around a circular bridge pier are presented.In the study reported herein,the fractal dimension of velocity fluctuations(u′,v′,w′) and the Reynolds shear stresses(u′v′ and u′w′) of flow around a bridge pier were computed using a Fractal Interpolation Function(FIF) algorithm.The velocity fluctuations of flow along a horizontal plane above the bed were measured using Acoustic Doppler Velocity meter(ADV)and Particle Image Velocimetry(P1V).The PIV is a powerful technique which enables us to attain high resolution spatial and temporal information of turbulent flow using instantaneous time snapshots.In this study,PIV was used for detection of high resolution fractal scaling around a bridge pier.The results showed that the fractal dimension of flow fluctuated significantly in the longitudinal and transverse directions in the vicinity of the pier.It was also found that the fractal dimension of velocity fluctuations and shear stresses increased rapidly at vicinity of pier at downstream whereas it remained approximately unchanged far downstream of the pier.The higher value of fractal dimension was found at a distance equal to one times of the pier diameter in the back of the pier.Furthermore,the average fractal dimension for the streamwise and transverse velocity fluctuations decreased from the centreline to the side wall of the flume.Finally,the results from ADV measurement were consistent with the result from PIV,therefore,the ADV enables to detect turbulent characteristics of flow around a circular bridge pier. 相似文献
14.
Arching in Inclined and Vertical Mine Stopes 总被引：2，自引：1，他引：1
Shailesh Singh Sanjay Kumar Shukla Nagaratnam Sivakugan 《Geotechnical and Geological Engineering》2011,29(5):685-693
Hydraulic fills are one of the most common backfills used by mining industries to backfill the stopes (voids) created after
extracting the ore. It is important to estimate the stresses within to the stope to design the drainage and barricades. Most
of the existing analytical models for the estimation of stresses within the stopes consider flat rectangular elements to include
the effects of arching, although a continuous compression catenary arch of principal stresses using intersections of shear
lines is the reality in field situations. In this paper, a circular compression arch of principal stresses has therefore been
used to derive a general expression for stress within the inclined stopes. The results have been compared with the existing
analytical and numerical models for vertical stopes as well as inclined stopes. A methodology has been presented to determine
the vertical stress variation along the width of stope at different depths. The variation of stresses along the width of stope
is also presented graphically. 相似文献
15.
Experimental and numerical studies on and sand–steel interfaces are presented. Emphasis is laid on the effect of boundary conditions of the whole system and of localized deformation. The experiments with different roughness of steel surface, sand density, normal stress and grain size are carried out in a plane strain apparatus, a parallely guided direct shear apparatus and in a planar silo model with a movable bottom and parallel steel walls. During the test in the plane strain apparatus the localized zone is observed with the help of X-rays. The results indicate a significant effect of wall roughness and boundary conditions of the whole system on the wall friction angle and the thickness of the localized zone along the steel surface. An elastoplastic constitutive model established within the framework of a Cosserat continuum, capable of describing isotropic hardening, softening and dilatancy, is implemented in a finite element code. The model differs from the conventional theory of plasticity due to the presence of Cosserat rotation and couple stress using the mean grain diameter as the characteristic length. Finite element simulations of simple shear tests are presented. The additional boundary condition along the steel plate, characteristic of the Cosserat continuum, allows for modelling the different roughness of the steel plate with consideration of grain rotations. A comparison between the numerical calculations and the experimental results shows acceptable agreement. 相似文献
16.
通过室内大型直剪试验和基于PFC2D的颗粒离散元数值模型,探讨考虑块石破碎的土石混合料的剪切特性及块石破碎特征。以土石混合料室内大型直剪试验和筛分试验为基础,提出了一种能真实描述块石形态特征并准确反映块石破碎效应的土石混合料颗粒离散元数值建模方法,模拟并分析了6种含石量土石混合料在4种不同法向应力作用下的剪切特性及块石破碎特征。结果表明：土石混合料抗剪强度随含石量的增大而增大,且基本符合摩尔-库仑（M-C）强度准则,随着含石量增大,内摩擦角呈现“慢-快-慢”增长趋势,黏聚力则呈现先增后减再增大的变化趋势。剪切后土石混合料块石破碎形式可归纳为表面研磨、局部破碎、完全破裂、完全破碎4种方式。提出了一种新的颗粒破碎指标,该指标能够准确描述粒径大于5 mm的块石的破碎程度,其随含石量和法向应力的增大而增大。通过对土石混合料颗粒离散元数值模型剪切面的分析发现,剪切面出现“剪斜”现象,其起伏程度随含石量增大愈加明显,且随着含石量增大剪切面附近剪裂隙数量增多,土石混合料在剪切过程中的破坏为拉-剪混合破坏。 相似文献
17.
This paper presents analytical elastic-plastic solutions for static stress loading analysis and quasi-static expansion analysis of a cylindrical cavity in Tresca materials, considering biaxial far-field stresses and shear stresses along the inner cavity wall. The two-dimensional static stress solution is obtained by assuming that the plastic zone is statically determinate and using the complex variable theory in the elastic analysis. A rigorous conformal mapping function is constructed, which predicts that the elastic-plastic boundary is in an elliptic shape under biaxial in situ stresses, and the range of the plastic zone extends with increasing internal shear stresses. The major axis of the elliptical elastic-plastic boundary coincides with the direction of the maximum far-field compression stress. Furthermore, considering the internal shear stresses, an analytical large-strain displacement solution is derived for continuous cavity expansion analysis in a hydrostatic initial stress filed. Based on the derived analytical stress and displacement solutions, the influence of the internal shear stresses on the quasi-static cavity expansion process is studied. It is shown that additional shear stresses could reduce the required normal expansion pressure to a certain degree, which partly explains the great reduction of the axial soil resistance due to rotations in rotating cone penetration tests. In addition, through additionally considering the potential influences of biaxial in situ stresses and shear stresses generated around the borehole during drillings, an improved cavity expansion approach for estimating the maximum allowable mud pressure of horizontal directional drillings (HDDs) in undrained clays is proposed and validated. 相似文献