首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 750 毫秒
1.
Hydrogeochemical processes that accompany seawater intrusion in coastal aquifers can alter the resulting water quality and are important ingredients in coastal aquifer management. The presence of dissolution–precipitation reactions and ion exchange in the mixing zone of the Biscayne aquifer (FL, USA) are suggested based on changes in major ion concentrations and mineral saturation indices (SI). Major ion concentrations from 11 groundwater samples are compared with theoretical mixing between freshwater and seawater. PHREEQC code was used to calculate saturation indices of the samples with respect to common phases in the Biscayne aquifer. High Ca2+ and HCO3 ? content of the samples is typical of waters in contact with carbonate aquifers. Water quality of the samples is mainly attributed to mixing and precipitation–dissolution reactions with calcite and dolomite. The samples were saturated with calcite (SI ~ 0) and undersaturated for dolomite (SI < 0), while a few samples showed dolomite saturation. Because gypsum and halite SI could be predicted by theoretical mixing, reactions with those minerals, if present, are thought to be insignificant. In the active intrusion areas, cation exchange also appears to modify water quality leading to excess Ca2+, but depleted Na+, Mg2+ and K+ concentrations. On the other hand, samples from previous intrusion areas plotted very close to the theoretical mixing line and approached equilibrium with the seawater.  相似文献   

2.
Sabkhas are ubiquitous geomorphic features in eastern Saudi Arabia. Seven brine samples were taken from Sabkha Jayb Uwayyid in eastern Saudi Arabia. Brine chemistry, saturation state with respect to carbonate and evaporate minerals, and evaporation-driven geochemical reaction paths were investigated to delineate the origin of brines and the evolution of both brine chemistry and sabkha mineralogy. The average total dissolved solids in the sabkha brines is 243 g/l. The order of cation dominance is Na+   >>  Mg2+ >>  Ca2+>K+, while anion dominance is Cl− >> SO4 2− >> HCO3 −. Based on the chemical divide principle and observed ion ratios, it was concluded that sabkha brines have evolved from deep groundwater rather than from direct rainfall, runoff from the surroundings, or inflow of shallow groundwater. Aqueous speciation simulations show that: (1) all seven brines are supersaturated with respect to calcite, dolomite, and magnesite and undersaturated with respect to halite; (2) three brines are undersaturated with respect to both gypsum and anhydrite, while three brines are supersaturated with respect to both minerals; (3) anhydrite is a more stable solid phase than gypsum in four brines. Evaporation factors required to bring the brines to the halite phase boundary ranged from 1.016 to 4.53. All reaction paths to the halite phase boundary follow the neutral path as CO2 is degassed and dolomite precipitates from the brines. On average, a sabkha brine containing 1 kg of H2O precipitates 7.6 g of minerals along the reaction path to the halite phase boundary, of which 52% is anhydrite, 35.3% is gypsum, and 12.7% is dolomite. Bicarbonate is the limiting factor of dolomite precipitation, and sulfate is the limiting factor of gypsum and anhydrite precipitation from sabkha brines.  相似文献   

3.
Activity ratios of 234U/238U, 230Th/234U, and 230Th/232Th have been determined for calcite, gypsum and halite speleothems from caves of the Nullarbor Plain, mostly in the area N and NW of Mundrabilla Station, for the purpose of U-series dating. All calcite speleothems contain adequate amounts of uranium for dating, but some show an excess of 230Th. Stratigraphic relationships indicate that there were at least three phases of calcium carbonate deposition in the Nullarbor caves. The calcite samples, with one possible exception, have ages in excess of ca. 400000 yrs BP. This suggests that no significant amounts of calcium carbonate deposition have taken place during the last 400ka. At present, active deposition of speleothems is restricted almost entirely to gypsum and halite. The only gypsum speleothem dated was found to have a finite age of ca. 185 ka. Six dates on a small halite speleothem containing insect and arachnid remains indicate that it formed rapidly during Holocene time.  相似文献   

4.
In this paper, the hydrochemical isotopic characteristics of samples collected from geothermal springs in the Ilica geothermal field, Eastern Anatolia of Turkey, are examined and described. Low-temperature geothermal system of Ilica (Erzurum, Turkey) located along the Eastern Anatolian fault zone was investigated for hydrogeochemical and isotopic characteristics. The study of ionic and isotopic contents shows that the thermal water of Ilica is mainly, locally fed by groundwater, which changes chemically and isotopically during its circulation within the major fault zone reaching depths. The thermal spring has a temperature of 29–39 °C, with electrical conductivity ranging from 4,000 to 7,510 µS/cm and the thermal water is of Na–HCO3–Cl water type. The chemical geothermometers applied in the Ilica geothermal waters yielded a maximum reservoir temperature of 142 °C according to the silica geothermometers. The thermal waters are undersaturated with respect to gypsum, anhydrite and halite, and oversaturated with respect to dolomite. The dolomite mineral possibly caused scaling when obtaining the thermal waters in the study area. According to the enthalpy chloride-mixing model, cold water to the thermal water-mixing ratio is changing between 69.8 and 75 %. The δ18O–δ2H compositions obviously indicate meteoric origin of the waters. Thermal water springs derived from continental precipitation falling on to higher elevations in the study area. The δ13C ratio for dissolved inorganic carbonate in the waters lies between 4.63 and 6.48 ‰. In low-temperature waters carbon is considered as originating from volcanic (mantle) CO2.  相似文献   

5.
《Applied Geochemistry》2001,16(9-10):1153-1163
The waters of the thermal springs at Alhama de Granada vary in temperature between 27 and 45°C. Temporal changes in the composition of the principal spring (Baños Viejos) indicate that a small degree of mixing may occur between deep thermal waters and shallow groundwater. Slight compositional variations also occur between the various thermal springs in the study area. These spatial variations are due to the different local hydrodynamic conditions in the springs. Towards the north in less hydraulically transmissive rocks, cooling of the rising water is more noticeable, as are ion exchange and processes of SO4 reduction. The chemical composition of the water is related to the dissolution of evaporites (SO4 and Cl salts), carbonates and silicates, and to the possible existence of sources of S within the rock. Estimates of the mean residence times have been obtained based on 14CDIC and T. The state of thermodynamic equilibrium at the spring discharge was calculated using the SOLMINEQ.88 program. The results indicate that all the samples are supersaturated with respect to quartz, chalcedony, cristobalite, calcite, aragonite and dolomite, and undersaturated with respect to gypsum, anhydrite and halite. The use of different geothermometers and modelling of saturation indices for quartz, albite and anhydrite indicate temperatures of about 110°C.  相似文献   

6.
《Applied Geochemistry》2004,19(5):645-664
Sediment and water samples from 12 saline pans on the semi-arid west coast of South Africa were analysed to determine the origin of salts and geochemical evolution of water in the pans. Pans in the area can be subdivided into large, gypsiferous coastal pans with 79–150 g/kg total dissolved salt (TDS), small inland brackish to saline (2–64 g/kg TDS) pans and small inland brine (168-531 g/kg TDS) pans that have a layer of black sulphidic mud below a halite crust. The salinity of coastal pan waters varies with the seasonal influx of dilute runoff and dissolution of relict Pleistocene marine evaporite deposits. In contrast, inland pans are local topographic depressions, bordered on the north by downslope lunette dunes, where solutes are concentrated by evaporation of runoff, throughflow and groundwater seepage. The composition of runoff and seepage inflow waters is determined by modification of coastal rainfall by weathering, calcite precipitation and ion exchange reactions in the predominantly granitic catchment soils. Evaporation of pan waters leads to precipitation of calcite, Mg–calcite, dolomite, gypsum and halite in a distinct stratigraphic succession in pan sediments. Bicarbonate limits carbonate precipitation, Ca limits gypsum precipitation and Na limits halite precipitation. Dolomitisation of calcite is enhanced by the high Mg/Ca ratio of brine pan waters. Brine pan waters evolve seasonally from Na–Cl dominated brines in the wet winter months to Mg–Cl dominated brines in the dry summer months, when 5–20 cm thick halite crusts cover pan surfaces. Pan formation was probably initiated during a drier climate period in the early Holocene. More recent replacement of natural vegetation by cultivated land may have accelerated salt accumulation in the pans.  相似文献   

7.
The major cation and anion compositions of waters from the Lake Qinghai river system (LQRS) in the northeastern Tibetan Plateau were measured. The waters were collected seasonally from five main rivers during pre-monsoon (late May), monsoon (late July), and post-monsoon (middle October). The LQRS waters are all very alkaline and have high concentrations of TDS (total dissolved solids) compared to rivers draining the Himalayas and the southeastern Tibetan Plateau. Seasonal variations in the water chemistry show that, except the Daotang River, the TDS concentration is high in October and low in July in the LQRS waters. The forward models were used to quantify the input of three main rivers (Buha River, Shaliu River, and Hargai River) from rain, halite, carbonates, and silicates. The results suggest that (1) atmospheric input is the first important source for the waters of the Buha River and the Shaliu River, contributing 36–57% of the total dissolved cations, (2) carbonate weathering input and atmospheric input have equal contribution to the Hargai River water, (3) carbonate weathering has higher contribution to these rivers than silicate weathering, and (4) halite is also important source for the Buha River. The Daotang River water is dominated by halite input owing to its underlying old lacustrine sediments. The water compositions of the Heima River are controlled by carbonate weathering and rainfall input in monsoon season, and groundwater input may be important in pre-monsoon and post-monsoon seasons. After being corrected the atmospheric input, average CO2 drawdown via silicate weathering in the LQRS is 35 × 103 mol/km2 per year, with highest in monsoon season, lower than Himalayas and periphery of Tibetan Plateau rivers but higher than some rivers draining shields.  相似文献   

8.
Sedimentologic and biostratigraphic evidence is used to develop a geochemical model for Great Salt Lake, Utah, extending back some 30,000 yrs. B.P. Hydrologie conditions as defined by the water budget equation are characterized by a lake initially at a low, saline stage, rising by about 17,000 yrs. B.P. to fresh water basin-full conditions (Bonneville level) and then, after about 15,000 yrs. B.P., dropping rapidly to a saline stage again, as exemplified by the present situation.Inflow composition has changed through time in response to the hydrologie history. During fresh-water periods high discharge inflow is dominated by calcium bicarbonate-type river waters; during saline stages, low discharge, NaCl-rich hydrothermal springs are significant solute sources. This evolution in lake composition to NaCl domination is illustrated by the massive mirabilite deposition, free of halite, following the rapid drawdown until about 8,000 years ago, while historic droughts have yielded principally halite.Hydrologic history can be combined with inferred inflow composition to derive concentration curves with time for each major solute in the lake. Calcium concentrations before the drawdown were controlled by calcite solubility, and afterwards by aragonite. Significant amounts of solutes are removed from the lake by diffusion into the sediments. Na+, Cl? and SO42? are also involved in salt precipitation. By including pore fluid data, a surprisingly good fit has been obtained between solute input over the time period considered and the amounts actually found in lake brines, pore fluids, salt beds and sediments. Excess amounts are present for calcium, carbonate and silica, indicating detrital input.  相似文献   

9.
The study presents composition data of 87 surface water samples from high alpine catchments of the Zermatt area (Swiss Alps). The investigated area covers 170 km2. It was found that the surface runoff acquires the dissolved solids mostly by reaction of precipitation water with the minerals of the bedrock. Total dissolved solids (TDS) vary from 6 to 268 mg L?1. All collected water shows a clear chemical signature of the bedrock mineralogy. The contribution of atmospheric input is restricted to small amounts of ammonium nitrate and sodium chloride. NH4 is a transient component and has not been detected in the runoff. Evaporation is not a significant mechanism for TDS increase in the Zermatt area. The chemical composition of the three main types of water can be related to the mineralogy of the dominant bedrock in the catchments. Specifically, Ca-HCO3 (CC) waters develop from metamorphic mafic rocks and from carbonate-bearing schists. Mg-HCO3 water originates from serpentinites and peridotites. Ca-SO4 (CS) waters derive from continental basement rocks such as pyrite-rich granite and gneiss containing oligoclase or andesine. The collected data suggest that, together with reaction time, modal sulfide primarily controls and limits TDS of the waters by providing sulfuric acid for calcite (CC waters) and silicate (CS waters) dissolution. If calcite is present in the bedrock, its dissolution neutralizes the acid produced by sulphide weathering and buffers pH to near neutral to weakly alkaline conditions. If calcite is absent, the process produces low-pH waters in gneiss and granite catchments. The type of bedrock and its mineral assemblage can be recognized in water leaving very small catchments of some km2 area. The large variety of water with a characteristic chemical signature is an impressive consequence of the richly diverse geology and the different rock inventory of the local catchments in the Zermatt area.  相似文献   

10.
Mine water samples collected from different mines of the North Karanpura coalfields were analysed for pH, electrical conductivity, total dissolved solids (TDS), total hardness (TH), major anions, cations and trace metals to evaluate mine water geochemistry and assess solute acquisition processes, dissolved fluxes and its suitability for domestic, industrial and irrigation uses. Mine water samples are mildly acidic to alkaline in nature. The TDS ranged from 185 to 1343 mg L?1 with an average of 601 mg L?1. Ca2+ and Mg2+ are the dominant cations, while SO4 2? and HCO3 ? are the dominant anions. A high concentration of SO4 2? and a low HCO3 ?/(HCO3 ? + SO4 2?) ratio (<0.50) in the majority of the water samples suggest that either sulphide oxidation or reactions involving both carbonic acid weathering and sulphide oxidation control solute acquisition processes. The mine water is undersaturated with respect to gypsum, halite, anhydrite, fluorite, aluminium hydroxide, alunite, amorphous silica and oversaturated with respect to goethite, ferrihydrite, quartz. About 40% of the mine water samples are oversaturated with respect to calcite, dolomite and jarosite. The water quality assessment shows that the coal mine water is not suitable for direct use for drinking and domestic purposes and needs treatment before such utilization. TDS, TH, F?, SO4 2?, Fe, Mn, Ni and Al are identified as the major objectionable parameters in these waters for drinking. The coal mine water is of good to suitable category for irrigation use. The mines of North Karanpura coalfield annually discharge 22.35 × 106 m3 of water and 18.50 × 103 tonnes of solute loads into nearby waterways.  相似文献   

11.
There are 59 springs at the Gevas–Gurp?nar–Güzelsu basins, 38 of these springs emerge from the fractured karst aquifers (recrystallized limestone and travertine) and 21 emerge from the Yuksekova ophiolites, K?rkgeçit formation and alluvium. The groundwater samples collected from 38 out of the total of 59 springs, two streams, one lake and 12 wells were analyzed physico-chemically in the year 2002. EC and TDS values of groundwater increased from the marble (high altitude) to the ophiolites and alluvium (toward Lake Van) as a result of carbonate dissolution and connate seawater. Five chemical types of groundwater are identified: Ca–Mg–HCO3, Mg–Ca–HCO3, Mg–Na–HCO3, Na–Ca–HCO3 and Mg–Ca–Na–HCO3. The calculations and hydrochemical interpretations show that the high concentrations of Ca2+, Mg2+ and HCO3 ? as predominant ions in the waters are mainly attributed to carbonate rocks and high pCO2 in soil. Most of the karst springs are oversaturated in calcite, aragonite and dolomite and undersaturated in gypsum, halite and anhydrite. The water–rock interaction processes that singly or in combination influence the chemical composition of each water type include dissolution of carbonate (calcite and dolomite), calcite precipitation, cation exchange and freshening of connate seawater. These processes contribute considerably to the concentration of major ions in the groundwater. Stable isotope contents of the groundwater suggest mainly direct integrative recharge.  相似文献   

12.
The high As and F− groundwaters from Datong Basin are mostly soda waters with a Na/(Cl+SO4) (meq) ratio greater than unity, As and F− up to 1550 μg/L and 10.4 mg/L, respectively, and with pH between 7.6 and 9.1. Geochemical modeling indicates that the waters are oversaturated with respect to calcite and clay minerals such as kaolinite, and undersaturated with respect to primary rock-forming minerals such as anorthite and albite. The water chemistry also is affected by evapotranspiration. The degree of evaporative enrichment is up to 85 in terms of Cl−. Results of the hydrogeochemical studies indicate that the occurrence of soda water at Datong is the result of incongruent dissolution of aluminosilicates at one stage of their interaction with groundwater when the water is oversaturated with respect to calcite and evapotranspiration-related salt accumulation is not too strong. Studying the genesis of soda waters provides new insights into mechanism of As and F− enrichment in the aquifer system. Due to CaF2 solubility control and OH−–F− exchange reactions, F− can be enriched in soda water. And the high pH condition of soda water favors As desorption from oxyhydroxide surfaces, thereby increasing the concentration of As in the aqueous phase.  相似文献   

13.
The composition of waters from 10 thermal springs located in western Virginia near the 38th parallel lineament have been analysed for major dissolved components and for Sr, Fe, Cu, Zn and Cd; from these analyses, free ion activities have been calculated. The temperatures of the springs range from 17° to 39°C, the heat apparently being derived simply from deep circulation along synclinal, Middle Ordovician limestones. More than 95 per cent of the dissolved solids consist of Ca2+, Mg2+ HCO3?, and SO42?. The concentrations of these components, as well as the spring temperatures, have not changed appreciably in 140 yr in some springs. The waters that have temperatures below 25° are all undersaturated with respect to calcite and dolomite, possibly because they have been contaminated by shallow ground waters. The waters with temperatures above 25° are in equilibrium with calcite and dolomite. Furthermore, in this latter group, the calcium-sulfate activity product and the sulfate-carbonate activity ratio are nearly constant, even though the waters are under saturated with respect to gypsum, anhydrite, celestite and strontianite. This can be explained if CaSO4 is coprecipitated in a mineral such as aragonite. The waters have absorbed some dissolved oxygen near the surface, but at depth they may be anoxic with Eh controlled by the oxidation of pyrite to goethite. The extremely low chloride concentrations of these waters clearly distinguish them from the brines which deposited Mississippi Valley and Appalachian type epithermal ore deposits.  相似文献   

14.
Study of the groundwater samples from Tajarak area, western Iran, was carried out in order to assess their chemical compositions and suitability for agricultural purposes. All of the groundwaters are grouped into two categories: relatively low mineralized of Ca–HCO3 and Na–HCO3 types and high mineralized waters of Na–SO4 and Na–Cl types. The chemical evolution of groundwater is primarily controlled by water–rock interactions mainly weathering of aluminosilicates, dissolution of carbonate minerals and cation exchange reactions. Calculated values of pCO2 for the groundwater samples range from 2.34 × 10−4 to 1.07 × 10−1 with a mean value of 1.41 × 10−2 (atm), which is above the pCO2 of the earth’s atmosphere (10−3.5). The groundwater is oversaturated with respect to calcite, aragonite and dolomite and undersaturated with respect to gypsum, anhydrite and halite. According to the EC and SAR the most dominant classes (C3-S1, C4-S1 and C4-S2) were found. With respect to adjusted SAR (adj SAR), the sodium (Na+) content in 90% of water samples in group A is regarded as low and can be used for irrigation in almost all soils with little danger of the development of harmful levels of exchangeable Na+, while in 40 and 37% of water samples in group B the intensity of problem is moderate and high, respectively. Such water, when used for irrigation will lead to cation exchange and Na+ is adsorbed on clay minerals while calcium (Ca2+) and magnesium (Mg2+) are released to the liquid phase. The salinity hazard is regarded as medium to high and special management for salinity control is required. Thus, the water quality for irrigation is low, providing the necessary drainage to avoid the build-up of toxic salt concentrations.  相似文献   

15.
Apparently anomalous levels of Cu, Pb, Zn (up to 6.1, 26.0 and 10.8 mg 1−1 respectively) and Ra (2000 pg 1−1) have been noted in groundwaters from 28 drill holes within a 20 km × 20 km zone centred about a 10 times background airborne radiometric anomaly near Lake Maurice in the Great Victoria Desert in South Australia. Within 6 km of the anomaly centre the water table depth is generally less than 10 m, increasing to approximately 30 m in the drill holes furthest from the anomaly centre. All waters are very acid (pH 3.6 to 5.8) and deficient in carbonate species (all <0.5 mg 1−1) but saturated with respect to calcium sulphate minerals. XRD traces of drill hole cuttings show the presence of quartz and halite at every sample site, pyrite at 75% of sites, variable amounts of kaolinite and muscovite at all sites, and variable amounts of feldspar, jarosite, calcium sulphate minerals, hydrated iron oxides, siderite, chlorite and calcite at certain locations only. Salinity of waters is very high ranging from that approximating sea water (Ionic strength (I) = 0.93 and Cl− = 19 g 1−1) to approximately six times sea water salinity (I = 4.61 and Cl− = 120 g 1−1).  相似文献   

16.
Precipitation, soil and spring waters from an outlier of Chalk were analysed over a one year period for field pH, and contents of Ca+2, Mg+2, HCO3? and other dissolved solids. Measured soil log PCO2 (atm) varied between a minimum of ?2.60 and maximum of ?1.46, and could be predicted from measurements of soil temperature. Soil waters evolved under open system conditions with respect to soil CO2, and were undersaturated with calcite during the winter recharge period.The chemistry of the springs is related to their topographic position. Group 1 springs, located below a feather edge of chalk, had both their minimum and maximum PCO2s predicted by the soil CO2 data, suggesting open system CO2 evolution. Group 2 springs, located along the scarp slope had minimum PCO2s predicted by the soil data, but maximum PCO2s which could only be explained by a closed system evolution from the maximum soil CO2 observed. Group 1 springs were close to calcite saturation, whereas Group 2 springs were significantly undersaturated with calcite. The two groups could be identified by linear discriminant analysis of measured Ca2+, pH and HCO3? concentrations.  相似文献   

17.
A thermodynamic model is developed for the calculation of both phase and speciation equilibrium in the H2O-CO2-NaCl-CaCO3-CaSO4 system from 0 to 250 °C, and from 1 to 1000 bar with NaCl concentrations up to the saturation of halite. The vapor-liquid-solid (calcite, gypsum, anhydrite and halite) equilibrium together with the chemical equilibrium of H+,Na+,Ca2+, , , and CaSO4(aq) in the aqueous liquid phase as a function of temperature, pressure and salt concentrations can be calculated with accuracy close to the experimental results.Based on this model validated from experimental data, it can be seen that temperature, pressure and salinity all have significant effects on pH, alkalinity and speciations of aqueous solutions and on the solubility of calcite, halite, anhydrite and gypsum. The solubility of anhydrite and gypsum will decrease as temperature increases (e.g. the solubility will decrease by 90% from 360 K to 460 K). The increase of pressure may increase the solubility of sulphate minerals (e.g. gypsum solubility increases by about 20-40% from vapor pressure to 600 bar). Addition of NaCl to the solution may increase mineral solubility up to about 3 molality of NaCl, adding more NaCl beyond that may slightly decrease its solubility. Dissolved CO2 in solution may decrease the solubility of minerals. The influence of dissolved calcite on the solubility of gypsum and anhydrite can be ignored, but dissolved gypsum or anhydrite has a big influence on the calcite solubility. Online calculation is made available on www.geochem-model.org/model.  相似文献   

18.
The Pennsylvanian phylloid algal mounds exposed in the Cervatina Limestone of the Cantabrian Zone (NW Spain) developed during the highstands of high-frequency shallowing-upward cycles and lack evidence of subaerial exposure at their tops. Mound core facies are composed of massive bafflestones with variable amounts of calcite cements and anchicodiacean phylloid algae with cyathiform thalli preserved in growth position. Through standard petrographic, isotopic (δ18O and δ13C), major and trace element (Ca, Mg, Fe, Mn, Sr) and cathodoluminescence analyses, five calcite cement phases (cement 1 (C1)–cement 5 (C5)) have been identified filling primary and secondary pores. Early marine diagenesis is represented by micritization and non-luminescent to mottled-dull luminescent high-Mg calcite fibrous marine cement (C1). A dissolution phase then occurred and created vuggy and moldic pores. Based on the absence of field or petrographical or geochemical evidence of exposure, it is inferred that dissolution occurred in near-surface undersaturated marine waters with respect to aragonite related to progressive organic matter oxidation. Secondary porosity was subsequently filled by dull-bright-dull bladed high-Mg calcite (C2), which precipitated in the early shallow burial from marine-derived pore waters. Remaining porosity was occluded by shallow-burial precipitates consisting of non-luminescent scalenohedral low-Mg calcite (C3) followed by non-ferroan dull luminescent calcite spar (C4). Latter phases of calcite spar exhibiting non- and dull luminescence (C5) are associated with burial calcite veins. Low δ18O values (around ?8‰), moderately depleted δ13C values (around 0.5‰) and the homogeneity of trace element contents of carbonate matrix, cements and vein-filling calcites suggest burial isotopic re-equilibration and recrystallization, probably in Early Permian times during post-thrusting orocline formation.  相似文献   

19.
Intergranular pressure solution (IPS) is a coupled chemical-mechanical process of widespread importance that occurs during diagenesis and low-temperature deformation of sedimentary rocks. Laboratory experiments on IPS in halite, quartz, and calcite have largely concentrated on the mechanical aspects of the process. In this study, we report the effects of pore fluid chemistry, specifically varying phosphate ion concentration, on the mechanical compaction by IPS of fine-grained calcite powders at room temperature and 1 to 4 MPa applied effective stress. Phosphate was investigated because of its importance as a biogenic constituent of sea and pore waters. Increasing the pore fluid phosphate concentration from 0 to 10−3 mol/L systematically reduced compaction strain rates by up to two orders of magnitude. The sensitivity of the compaction strain rate to phosphate concentration was the same as the sensitivity of calcite precipitation rates to the addition of phosphate ions reported in the literature, suggesting that the rate of IPS in phosphate-bearing samples was controlled by calcite precipitation on pore walls. The results imply that IPS and associated porosity/permeability reduction rates in calcite sediments may be strongly reduced when pore fluids are enriched in phosphates, for example, through high biologic productivity or a seawater origin. Future modeling of IPS-related processes in carbonates must therefore take into account the effects of pore fluid chemistry, specifically the inhibition of interfacial reactions.  相似文献   

20.
Uttarakhand geothermal area, located in the central belt of the Himalayan geothermal province, is one of the important high temperature geothermal fields in India. In this study, the chemical characteristics of the thermal waters are investigated to identify the main geochemical processes affecting the composition of thermal waters during its ascent toward the surface as well as to determine the subsurface temperature of the feeding reservoir. The thermal waters are mainly Ca–Mg–HCO3 type with moderate silica and TDS concentrations. Mineral saturation states calculated from PHREEQC geochemical code indicate that thermal waters are supersaturated with respect to calcite, dolomite, aragonite, chalcedony, quartz (SI > 0), and undersaturated with respect to gypsum, anhydrite, and amorphous silica (SI < 0). XRD study of the spring deposit samples fairly corroborates the predicted mineral saturation state of the thermal waters. Stable isotopes (δ18O, δ2H) data confirm the meteoric origin of the thermal waters with no oxygen-18 shift. The mixing phenomenon between thermal water with shallow ground water is substantiated using tritium (3H) and chemical data. The extent of dilution is quantified using tritium content of thermal springs and non-thermal waters. Classical geothermometers, mixing model, and multicomponent fluid geothermometry modeling (GeoT) have been applied to estimate the subsurface reservoir temperature. Among different classical geothermometers, only quartz geothermometer provide somewhat reliable estimation (96–140 °C) of the reservoir temperature. GeoT modeling results suggest that thermal waters have attained simultaneous equilibrium with respect to minerals like calcite, quartz, chalcedony, brucite, tridymite, cristobalite, talc, at the temperature 130 ± 5 °C which is in good agreement with the result obtained from the mixing model.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号