共查询到20条相似文献，搜索用时 250 毫秒
1.
Effects of recoverable deformation induced anisotropy in the elastic stiffness of isotropic materials are described. In isotropic materials, thermodynamics predicts coupling of hydrostatic and deviatoric responses. It is shown that the coupling of the two responses is more significant than previously recognized in the literature. Properly accounting for the coupling of hydrostatic and deviatoric responses requires re‐evaluating elastic materials characterization data, allowing for the coupled response. The result is an apparent decrease in the pressure sensitivity of the elastic shear modulus. The decrease in the pressure sensitivity of the shear modulus leads to stress paths that are more tangential to the yield surface in stress space, resulting in an increase in predicted elastic strain at each step of an elastic–plastic stress update. Consequently, predicted plastic strains and, in particular, volumetric plastic strains, are smaller than if recoverable deformation induced anisotropy had been neglected. The result is an associated plasticity model, which appears to be non‐associated. Copyright © 2012 John Wiley & Sons, Ltd. 相似文献
2.
A matrix relating stress and elastic strain tensors for anisotropic particulate materials has been derived. The magnitude of the matrix depends on the state of the material anisotropy. Anisotropy in granular materials depends on strain because normal and tangential particle contact forces, as well as the spatial distribution of the contacts, vary with stress and strain. However, the rotation tensor and the strain tensor cannot be independent; they must satisfy certain constraints to meet the requirement for macroscopic stress tensor symmetry. These conditions and constraints lead to the derivation of the matrix presented in this article. The principal directions of the stress tensor and strain tensor are generally not coincident, and the values of deformation parameters, Young's modulus and Poisson's ratio, are direction dependent; these two aspects are also discussed in this paper. Whereas this matrix can be used in static numerical analyses for elastic problems, we note that this relationship can also be used as a basis upon which to derive a fully incremental stress–strain relationship for anisotropic granular materials in the plastic state, where the anisotropy is evolving with strain. 相似文献
3.
A discrete plastic–damage model is developed for cohesive‐frictional geomaterials subjected to compression‐dominated stresses. Macroscopic plastic strains of material are physically generated by frictional sliding along weakness planes. The evolution of damage is related to the evolution of weakness planes physically in connection with the propagation of microcracks. A discrete approach is used to account for anisotropic plastic flow and damage evolution, by introducing two stress invariants and one plastic hardening variable for each family of sliding weakness planes. Plastic flow in each family is coupled with damage evolution. The proposed model is applied to typical geomaterials and comparisons between numerical predictions and experimental data are presented. Copyright © 2009 John Wiley & Sons, Ltd. 相似文献
4.
G. S. Wang 《国际地质力学数值与分析法杂志》2005,29(15):1457-1483
In this paper, the interaction of double‐periodical cracks is accurately solved based on the isolating analysis procedure, superposition principle, pseudo‐traction method, Chebyshev polynomial expansion and crack‐surface collocation technique. The jump displacement crossing crack faces, the average additional strain and therefore the effective compliance of the double‐periodically cracked plate are directly determined. The numerical results for axial‐symmetrically distributed double‐periodical cracks, general double‐periodical cracks with one collinear direction as well as two sets of double‐periodical cracks with same size and square distribution are given in this paper. And the partial typical numerical results are compared with the previous works. The analysis shows that the anisotropy induced by the general double‐periodical cracks is generally not orthogonal anisotropy. Only when the double‐periodical cracks are axial‐symmetrically distributed, is the anisotropy orthogonal. In this special cases, the effective engineering constants (consist of effective elastic modulus, the effective Poisson's ratio, the effective shear modulus) of cracked plate versus crack spacing, in the plane stress and plane strain conditions, respectively, are analysed. Copyright © 2005 John Wiley & Sons, Ltd. 相似文献
5.
页岩各向异性特征的试验研究 总被引：9，自引：0，他引：9
为研究彭水页岩气区块储层的各向异性特征,开展了石柱县龙马溪组页岩的单轴和三轴压缩试验,分析了其力学特性、强度特征和破裂模式的各向异性,并揭示了其破坏机制的各向异性。结果表明：(1) 龙马溪组页岩具有明显的各向异性特征,弹性模量在平行层理方向最大,垂直层理方向最小,且围压的增加使其增加速率不断减小;0°、30°和60°、90°页岩的泊松比随围压的增加呈现出了相反的变化规律,这可能与页岩层理间孔隙和微裂缝的良好发育有关。(2) 相同围压下,0°试样强度最高,90°次之,30°最低,总体上呈现出两边高、中间低的U型变化规律,而不同角度的Hoek-Brown强度准则能较好地反映其强度的各向异性特征。(3) 页岩破裂模式的各向异性是由破坏机制的各向异性引起的,而强度的各向异性是由破坏机制的各向异性控制的。单轴压缩时,0°页岩为沿层理的张拉劈裂破坏,30°为沿层理的剪切滑移破坏,60°为贯穿层理和沿层理的复合剪切破坏,90°为贯穿层理的张拉破坏。三轴压缩时,0°为贯穿层理的共轭剪切破坏,30°为沿层理的剪切滑移破坏,60°和90°为贯穿层理的剪切破坏;页岩地层的层状沉积结构和层理间的弱胶结作用是破坏机制各向异性的根源。研究结果为水平井井壁的稳定性分析和水力压裂施工设计等提供了技术参考。 相似文献
6.
G. Mortara 《国际地质力学数值与分析法杂志》2010,34(9):953-977
This paper proposes a yield and failure criterion for cohesive and frictional materials. The function is given by the combination of a Lode dependence for the behaviour in the deviatoric plane and a meridian function for the pressure‐dependent behaviour. A variety of shapes can be achieved with the proposed criterion including Lode dependences which are able to reproduce the behaviour of isotropic and cross‐anisotropic materials in the deviatoric plane. The criterion is validated through the comparison with experimental data based on multiaxial experimental tests on clays, sands, rocks and concrete. Finally, the convexity of the criterion is analysed and discussed. Copyright © 2009 John Wiley & Sons, Ltd. 相似文献
7.
This article is devoted to numerical modeling of anisotropic damage and plasticity in saturated quasi‐brittle materials such as rocks and concrete. The damaged materials are represented by an isotropic poroelastic matrix containing a number of families of microcracks. Based on previous works, a discrete thermodynamic approach is proposed. Each family of microcracks exhibits frictional sliding along crack surfaces as well as crack propagation. The frictional sliding is described by a Coulomb–Mohr‐type plastic criterion by taking into account the effect of fluid pressure through a generalized effective stress concept. The damage evolution is entirely controlled by and coupled with the frictional sliding. The effective elastic properties as well as Biot's coefficients of cracked porous materials are determined as functions of induced damage. The inelastic deformation due to frictional sliding is also taken into account. The procedure for the identification of the model's parameters is presented. The proposed model is finally applied to study both mechanical and poromechanical responses of a typical porous brittle rock in drained and undrained compression tests as well as in interstitial pressure controlled tests. The main features of material behaviors are well reproduced by the model. Copyright © 2012 John Wiley & Sons, Ltd. 相似文献
8.
Existing solutions to Mandel's problem focus on isotropic, transversely isotropic, and orthotropic materials, the last two of which have one of the material symmetry axes coincide with the vertical loading direction. The classical plane strain condition holds for all these cases. In this work, analytical solution to Mandel's problem with the most general matrix anisotropy is presented. This newly derived analytical solution for fully anisotropic materials has all the three nonzero shear strains. Warping occurs in the cross sections, and a generalized plane strain condition is fulfilled. This solution can be applied to transversely isotropic and orthotropic materials whose material symmetry axes are not aligned with the vertical loading direction. It is the first analytical poroelastic solution considering mechanical general anisotropy of elasticity. The solution captures the effects of material anisotropy and the deviation of the material symmetry axes from the vertical loading direction on the responses of pore pressure, stress, strain, and displacement. It can be used to match, calibrate, and simulate experimental results to estimate anisotropic poromechanical parameters. This generalized solution is capable of reproducing the existing solutions as special cases. As an application, the solution is used to study the responses of transversely isotropic and orthotropic materials whose symmetry axes are not aligned with the vertical loading direction. Examples on anisotropic shale rocks show that the effects of material anisotropy are significant. Mandel-Cryer's effects are highly impacted by the degree of material anisotropy and the deviation of the material symmetry axes from the vertical loading direction. 相似文献
9.
由于加荷方式不同,土体在复杂应力状态下在各主应力方向上应力-应变关系表现出显著应力各向异性,在常规三轴试验基础上,采用经典弹塑性理论各向同性土体模型对此不能合理描述。通过真三轴试验,总结应力各向异性柔度矩阵规律,结合试验规律进行相应理论研究,用非线性各向异性弹性矩阵代替弹塑性模型的弹性矩阵,用具有各向异性屈服准则的弹塑性模型描述塑性部分,建立非线性各向异性弹性-塑性模型,可以改善柔度矩阵矩阵形态,反映复杂应力状态下土体应力各向异性特征。 相似文献
10.
Poul V. Lade 《国际地质力学数值与分析法杂志》2006,30(4):307-333
Data from three‐dimensional experiments performed on sand in true triaxial equipment have been reviewed to sort out apparent disarray resulting from their interpretation. This has been done based on analyses made possible by recent developments and understanding of factors influencing sand behaviour: occurrence of shear banding, boundary conditions and/or specimen slenderness ratio, cross‐anisotropy, and stability of experimental technique. These factors are reviewed and test data from the literature are evaluated. Experimental data are divided into three groups in which: (a) homogeneous behaviour controls the sand strength; (b) shear banding affects the shape of the three‐dimensional failure surface in the midrange of values of b=(σ2?σ3)/(σ1?σ3), and (c) the data has been misinterpreted. Appropriate interpretation of three‐dimensional strength data for sand exhibiting isotropic, homogeneous behaviour is represented by a smoothly rounded triangular failure surface expressible in terms of the first and third stress invariants. Shear banding effects will cause the failure surface to be ‘indented’ in the midrange of b‐values in all sectors of the octahedral plane. Effects of cross‐anisotropy will result in lower strengths in sector III than in sector I of the octahedral plane, and the failure surface will appear as rotated around the stress origin in principal stress space. Copyright © 2005 John Wiley & Sons, Ltd. 相似文献
11.
An anisotropic geomechanical model for jointed rock mass is presented. Simultaneously with deriving the orthotropic anisotropy elastic parameters along the positive axis, the equivalent compliance matrix for the deflection axis orthotropic anisotropy was derived through a three-dimensional coordinate transformation. In addition, Singh’s analysis of the stress concentration effects of intermittent joints was adopted, based on two groups of intermittent joints and a set of cross-cutting joints in the jointed rock mass. The stress concentration effects caused by intermittent joints and the coupling effect of cross-cutting joints along the deflection-axis are also considered. The proposed anisotropic mechanics parameters method is applied to determine the deformation parameters of jointed granite at the Taishan Nuclear Power Station. Combined with the deterministic mechanical parameters of rock blocks and joints, the deformation parameters and their variability in jointed rock masses are estimated quantitatively. The computed results show that jointed granite at the Taishan Nuclear Power Station exhibits typical anisotropic mechanical characteristics; the elastic moduli in the two horizontal directions were similar, but the elastic modulus in the vertical direction was much greater. Jointed rock elastic moduli in the two horizontal and vertical directions were respectively about 24% and 37% of the core of rock, showing weakly orthotropic anisotropy; the ratio of elastic moduli in the vertical and horizontal directions was 1.53, clearly indicating the transversely isotropic rock mass mechanical characteristics. The method can be popularized to solve other rock mechanics problems in nuclear power engineering. 相似文献
12.
Elastic/plastic deformations in frictional materials under moving surface loads are investigated. The static and kinematic shakedown theorems are used to obtain estimates of the critical shakedown load for plane strain deformations under trapezoidal surface load distributions and for three-dimensional deformations under loads distributed over circular areas. It is shown that the material can fail either by incremental collapse or in cyclic or alternating collapse modes. 相似文献
13.
This article derives the closed‐form solutions for estimating the vertical surface displacements of cross‐anisotropic media due to various loading types of batter piles. The loading types include an embedded point load for an end‐bearing pile, uniform skin friction, and linear variation of skin friction for a friction pile. The planes of cross‐anisotropy are assumed to be parallel to the horizontal ground surface. The proposed solutions are never mentioned in literature and can be developed from Wang and Liao's solutions for a horizontal and vertical point load embedded in the cross‐anisotropic half‐space. The present solutions are identical with Wang's solutions when batter angle equals to 0°. In addition, the solutions indicate that the surface displacements in cross‐anisotropic media are influenced by the type and degree of material anisotropy, angle of inclination, and loading types. An illustrative example is given at the end of this article to investigate the effect of the type and degree of soil anisotropy (E/E′, G′/E′, and ν/ν′), pile inclination (α), and different loading types (a point load, a uniform skin friction, and a linear variation of skin friction) on vertical surface displacements. Results show that the displacements accounted for pile batter are quite different from those estimated from plumb piles, both driven in cross‐anisotropic media. Copyright © 2007 John Wiley & Sons, Ltd. 相似文献
14.
We consider discontinuous bifurcations as the indicator of a localized failure for a class of composites that are characterized by elastic fibres reinforcing an elastic–plastic matrix. A macroscopic tangent stiffness tensor for the fibre‐reinforced composite is developed by consistently homogenizing the contribution of fibres in a spherical representative volume element. Analytical solutions are derived for the critical hardening modulus and corresponding bifurcation directions for the case of plane strain loading. Properties of the solutions are further illustrated on the example of the non‐associated Drucker–Prager model at onset of yielding. Results show that presence of fibres decreases the critical hardening modulus, thus inhibiting the onset of strain localization. The rate of decrease in the critical hardening modulus is the highest for pure shear, followed by uniaxial tension, uniaxial compression, biaxial tension and biaxial compression. The main fibre parameters that control the onset of strain localization are their volumetric content and their stiffness modulus whereby very stiff fibres can produce the most significant decrease in the critical hardening modulus, especially for the state of biaxial tension. The critical hardening modulus for the non‐associated Drucker–Prager model exhibits a full range of localization modes including compaction bands, dilation bands, and transition in the form of shear bands regardless of the presence of fibres. Presence of fibres affects bifurcation directions, except in the case when Poisson's ratio of the matrix is equal to 0.25. The results demonstrate stabilizing effects of fibres by which they provide the control against the onset of strain localization. Copyright © 2006 John Wiley & Sons, Ltd. 相似文献
15.
Schistous rock can be considered—in a first approximation—as cross‐anisotropic linear elastic material. The determination of the corresponding material constants on the basis of the laboratory investigation of rock samples often fails, as the extraction of appropriate cores proves to be unfeasible (the cores disintegrate if the schistosity is pronounced). In this paper a new method is presented to determine the material constants of a linear elastic cross‐anisotropic rock on the basis of cavity expansion field tests, e.g. with a radial jack. To this purpose, an analytic approximation for the deformation of a hydrostatically loaded cylindrical cavity in cross‐anisotropic rock is derived which serves to the inverse analysis of the material parameters. Copyright © 2010 John Wiley & Sons, Ltd. 相似文献
16.
This paper introduces sequential limit analysis (SLA) as a method for modelling large plastic deformations of purely cohesive materials such as undrained clay. The method involves solving a series of consecutive small‐deformation plastic collapse problems using finite element limit analysis, thus ensuring high levels of accuracy, efficiency, and robustness. The techniques needed to develop an SLA implementation for two‐dimensional (plane strain) problems are described in detail, including model geometry updating routines, treatment of rigid bodies, interfaces and boundaries, and periodic remeshing and interpolation of field variables. A simple total stress‐based constitutive model is used to account for strain softening and strain rate effects. Extensive verifications and validations are performed using analytical solutions and physical model test results, comparing both collapse loads and failure mechanisms, to demonstrate the effectiveness of the SLA approach. Additional solution quality checks on the bracketing discrepancy between lower‐bound and upper‐bound limit analysis solutions, and on the incompressibility of the rigid‐plastic material, are also presented. 相似文献
17.
A. Gajo 《国际地质力学数值与分析法杂志》2010,34(2):111-134
Experimental evidence shows that soil stiffness at very small strains is strongly anisotropic and depends on the stress level and void ratio. In particular, stiffness anisotropy varies considerably in sand when subjected to cyclic loading, following the stress cycles applied. To model this behaviour, an innovative hyperelastic formulation based on the elastoplastic coupling is incorporated in a new kinematic hardening elastoplastic model. The proposed hyperelastic–plastic model is the first to be capable of correctly simulating all aspects of the small‐strain behaviour of granular materials subjected to monotonic and cyclic loads. This hyperelastic formulation is generally applicable to any elastoplastic model. Copyright © 2009 John Wiley & Sons, Ltd. 相似文献
18.
Qingli Dai 《国际地质力学数值与分析法杂志》2010,34(13):1321-1345
This paper presents parallel and serial viscoelasto‐plastic models to simulate the rate‐independent and the rate‐dependent permanent deformation of stone‐based materials, respectively. The generalized Maxwell viscoelastic and Chaboche's plastic models were employed to formulate the proposed parallel and serial viscoelasto‐plastic constitutive laws. The finite element (FE) implementation of the parallel model used a displacement‐based incremental formulation for the viscoelastic part and an elastic predictor—plastic corrector scheme for the elastoplastic component. The FE framework of the serial viscoelasto‐plastic model employed a viscoelastic predictor—plastic corrector algorithm. The stone‐based materials are consisted of irregular aggregates, matrix and air voids. This study used asphalt mixtures as an example. A digital sample was generated with imaging analysis from an optically scanned surface image of an asphalt mixture specimen. The modeling scheme employed continuum elements to mesh the effective matrix, and rigid bodies for aggregates. The ABAQUS user material subroutines defined with the proposed viscoelasto‐plastic matrix models were employed. The micromechanical FE simulations were conducted on the digital mixture sample with the viscoelasto‐plastic matrix models. The simulation results showed that the serial viscoelasto‐plastic matrix model generated more permanent deformation than the parallel one by using the identical material parameters and displacement loadings. The effect of loading rates on the material viscoelastic and viscoelasto‐plastic mixture behaviors was investigated. Permanent deformations under cyclic loadings were determined with FE simulations. The comparison studies showed that the simulation results correctly predicted the rate‐independent and rate‐dependent viscoelasto‐plastic constitutive properties of the proposed matrix models. Overall, these studies indicated that the developed micromechanical FE models have the abilities to predict the global viscoelasto‐plastic behaviors of the stone‐based materials. Copyright © 2009 John Wiley & Sons, Ltd. 相似文献
19.
An approximate two‐dimensional model for indentation of blunt objects into various types of rigid‐perfectly plastic cohesive‐frictional material is derived. Particular emphasis is placed on considering indentation as a process involving evolution of the boundary of material displaced by the indenter. Force–penetration relationships are obtained by an incremental approach utilizing key kinematic and static information from indentation of a flat punch. Albeit approximate, the proposed model applies to arbitrary indenter geometry and weightless or ponderable cohesive‐frictional materials exhibiting associated or non‐associated plastic flow. Two specific indenter geometries, the cylinder and blunt wedge, are explored in detail. Favorable agreement is found between the analytic results and those obtained using the finite element method (FEM). For both the wedge and cylinder, it is further shown that accurate analytic expressions relating indentation force explicitly to penetration can be derived. In the case of the wedge and weightless material, predictions of indentation force obtained from the derived expressions are very close to those computed from implicit equations available in the literature. Copyright © 2011 John Wiley & Sons, Ltd. 相似文献
20.
Traditional approaches for modeling the anisotropic elasticity response of the highly heterogeneous clay fabric in shale have mainly resorted to geometric factors such as definitions of particles shapes and orientations. However, predictive models based on these approaches have been mostly validated using macroscopic elasticity data. The recent implementation of instrumented indentation aimed at probing nano‐scale mechanical behaviors has provided a new context for characterizing and modeling the anisotropy of the porous clay in shale. Nanoindentation experimental data revealed the significant contribution of the intrinsic anisotropy of the solid clay to the measured elastic response. In this investigation, we evaluate both the effects of geometric factors and of the intrinsic anisotropic elasticity of the solid clay phase on the observed anisotropy of shale at multiple length scales through the development of a comprehensive theoretical micromechanics approach. It was found that among various combinations of these sources of anisotropy, the elastic response of the clay fabric represented as a granular ensemble of aligned effective clay particles with spherical morphology and anisotropic elasticity compares satisfactorily to nanoindentation and ultrasonic pulse velocity measurements at nano‐ and macroscopic length scales, respectively. Other combinations of sources of anisotropy could yield comparable predictions, particularly at macroscopic scales, at the expense of requiring additional experimental data to characterize the morphology and orientations of particles. Copyright © 2009 John Wiley & Sons, Ltd. 相似文献