共查询到20条相似文献，搜索用时 23 毫秒
1.
软黏土层一维有限应变固结的超静孔压消散研究 总被引：1，自引：0，他引：1
根据土力学固结理论计算分析软黏土层固结过程的超静孔隙水压力值,确定软黏土体固结过程的强度增长,对排水固结法处理软土地基至关重要。软黏土层固结过程中土体变形较大时,有限应变固结理论和小应变固结理论计算分析软黏土固结所得结果差异较大。利用非线性有限元法及程序,通过对软黏土层固结工程算例的计算结果分析,研究了有限应变固结理论和小应变固结理论计算分析软黏土层一维固结超静孔压值消散的差异;探讨了软黏土体一维固结过程中,几何非线性、土体渗透性变化和压缩性变化对超静孔隙水压力消散的影响。研究结果表明,当土体的变形较大时,有限应变固结理论计算出的超静孔压要比小应变固结理论得到的值消散的更快。考虑土体固结过程中渗透性的变化时,超静孔压消散变慢;可用软黏土渗透性变化指数ck 反映渗透性变化对超静孔压消散的影响,渗透性变化指数ck值越小、超静孔压消散越慢。固结过程中软黏土压缩性的大小及变化也影响超静孔压的消散,可用软黏土的压缩指数cc反映固结过程中压缩性的大小及变化对超静孔压消散的影响,软黏土的压缩指数cc越小,固结过程软黏土层中的超静孔压消散越快。 相似文献
2.
Field studies have shown that the driving of a displacement pile into cohesive soil generates large excess pore pressures in the vicinity of the pile. These pore pressures are often larger than the effective overburden pressure and facilitate the installation of the pile. The subsequent increase in bearing capacity of the pile is largely controlled by the dissipation of the excess pore pressures and a consequent increase in the effective stresses acting on the pile. The paper presents a closed formanalytical solution for the radial consolidation of the soil around a driven pile, assuming that the soil skeleton deforms elastically. This assumption is examined in the light of the predicted effective stress changes in the soil and is shown to lead to, a realistic model for the decay of pore pressure near the pile with time after driving. Although the solution may be applied to any initial distribution of excess pore pressure, attention is focussed on that due to the expansion of a cylindrical cavity in an ideal elastic, perfectly plastic soil. The resulting logarithmic variation of excess pore pressure with radius is considered to be close to that generated around a pile as a result of driving. In addition to giving estimates of the time needed for a driven pile to achieve its maximum strength, the solution may also be used in the analysis of pressuremeter tests to provide in-situ measurements of the coefficient of consolidation of the soil. 相似文献
3.
采用Barron轴对称固结及大变形固结问题的某些简化与假定,推导建立了砂井地基大变形固结控制方程,利用建立的双层砂井地基大变形固结方程及编制的计算程序,通过引入软土渗透系数、有效应力与孔隙比之间的幂函数关系k =ced与e=a( )b,对瞬时加载下双层砂井地基固结性状进行算例计算。结果表明：（1）双层软土幂函数渗透关系及压缩关系中诸参数对双层砂井地基固结性状有重要影响：随着两层软土幂函数渗透关系中参数c1、c2的增加（渗透性增加）、或幂函数压缩关系中参数a1、a2的增加,各土层水平径向与竖向孔隙比减小更快,沉降发展速率与超静孔压消散速率也相应增加,且沉降发展速率快于孔压消散速率。（2）两层土在分界面处的孔隙比及平均超静孔压均出现明显的突变,将沿深度分布曲线分成形状不同的两段,表现出不同的固结性状。 相似文献
4.
假定土体在固结过程中压缩性和渗透性的变化成正比,基于 - 及 - 关系,推导出饱和软土成层地基一维非线性固结解析解,分别给出了按沉降定义和按有效应力定义的每层土平均固结度及整个土层总固结度的计算公式。采用Fortran语言编制了相应的计算程序,将计算得到的结果与已有双层地基一维非线性固结解析解计算结果进行比较,验证该解析解的正确性。利用该程序分析成层地基一维非线性固结性状,分别讨论了初始竖向渗透系数、初始体积压缩系数、荷载值及土层厚度对地基固结性状的影响。分析结果表明：在成层地基一维非线性固结过程中,初始竖向渗透系数对超静孔压的影响较为复杂,对上下层地基固结速率影响不同;初始体积压缩系数增大,超静孔压增大,固结速率变小;所加荷载值越大,超静孔压消散越慢,固结发展越慢;超静孔压消散速率不仅取决于土层厚度,同时取决于各层土渗透性的相对大小。 相似文献
5.
以静压沉桩后桩周土体的应力状态为初始条件,根据桩周土体孔隙比、渗透系数和有效应力之间的相关性,在考虑固结系数随固结时间变化的条件下改进了轴对称条件下的太沙基固结控制方程。随后,采用分离变量法和离散化分析推导得出了桩周超孔隙水压力消散的半解析半数值解,并将解答与实测数据进行对比验证。在此基础上,采用空间滑动面理论改进的修正剑桥模型（SMP-MCC）定义土体三维不排水抗剪强度,研究了静压桩周土体强度、剪切模量随固结时间的变化规律。研究结果表明：由于解答考虑了固结系数随固结时间的变化,因而与实测结果吻合良好;土体压缩指数与渗透指数之比对土体固结系数和孔压消散速率影响较大;当土体压缩指数与渗透指数之比为1时,土体固结系数保持不变,解答退化为经典的太沙基轴对称固结方程;土体强度和剪切模量随固结时间的增长而逐步增加,固结完成后其值超越了土体原位强度和原位剪切模量。 相似文献
6.
假设桩周土体为饱和黏弹性介质,采用Burgers流变模型进行描述,同时考虑竖向和径向固结,建立了固结控制方程。根据不排水和自由排水情况,将边界条件分为3类并分别得到超孔隙水压力消散的级数解答,该解答能够为孔压静力触探反求固结系数提供一定的理论依据。在此基础上编制了应用程序,对Burgers流变模型中主要参数进行了分析。结果表明,地基表面自由排水、桩端地基不排水条件下,在一定深度以内的桩周土体的固结速度随深度降低,但超过某一范围后固结速度趋于稳定;上、下边界均自由排水条件下,固结速度随深度增加呈现下降、稳定、升高;上、下边界均不排水条件时,孔压消散速度不随深度变化,可简化为本解答仅考虑径向固结的特例。同时土体的流变特性对超孔隙水压力消散的影响比较显著,流变参数G1/1的变化使超孔隙水压力趋于某不为0的定值,且该值随G1/1比值的增大而增加;其他参数不变时,土体剪切刚度比G1/G2的增大会引起孔压消散速度的下降。 相似文献
7.
基于Fredlund非饱和土一维固结理论,研究了有限厚度的表面透水透气、底面不透水不透气的线弹性和黏弹性非饱和土地基在加荷随时间指数性变化时的一维固结特性。分别得到了两类地基在固结过程中同时考虑液相、气相渗透系数非线性变化和仅考虑液相渗透系数变化两种情况下的半解析解答。利用典型算例进行计算,分析了不同情况下两类地基中超孔隙水、气压力消散以及地基固结度随时间的变化规律,并与不考虑渗透系数变化时的半解析解计算结果进行了对比。结果发现：固结过程中渗透系数呈非线性变化;只考虑液相渗透系数变化时,超孔隙气压力的消散变化不大,超孔隙水压力的消散加快;气相渗透系数变化对超孔隙气的消散产生明显影响,对超孔隙水压力消散影响不大。同时考虑液相和气相渗透系数变化时,土体中超孔隙水、气压力的消散均有明显变化,土体固结速度也相应加快;分析结果对非饱和土固结的进一步研究具有重要意义。 相似文献
8.
Consolidation of sensitive clays: a numerical investigation 总被引：1，自引：1，他引：0
Consolidation of sensitive clay layers, which have significant compressibility at different stress states, is investigated via a nonlinear one-dimensional consolidation approach with a piecewise linear e ~ log10σ′ model. The behaviour of sensitive clays during consolidation and the limitations of conventional consolidation theory are addressed. It is shown that (1) the sensitive clay layer can be divided by the preconsolidation pressure into two zones, that is, high- and low-compressibility zones. The progressive destruction of particle cementation bonding through the soil layer is shown by the moving front of the interface between these two zones; (2) the excess pore pressure dissipation primarily takes place in the low-compressibility zone, which results in a small settlement during the early stages of consolidation; (3) conventional consolidation theory highly overestimates the settlement and gives a poor prediction of effective stress distribution. 相似文献
9.
Mengmeng Lu Shanyong Wang Scott W. Sloan Buddhima Indraratna Kanghe Xie 《国际地质力学数值与分析法杂志》2015,39(1):51-62
By incorporating the nonlinear variation of a soil's compressibility and permeability during the process of consolidation, an analytical solution for the radial consolidation of vertical drains has been developed for a general time‐variable loading. The general solution was verified for the cases of instantaneous loading and ramp loading. Detailed solutions were further derived for two special loading schemes: multistage loading and preloading–unloading–reloading. The nonlinear consolidation behavior of a vertical drain subjected to these two types of loading schemes was then investigated by a parametric study. The results show that the loading rate, the ratio of the compressibility index to the permeability index (Cc/Ck), and the initial stress state have a significant influence on the consolidation rate. A smaller value of Cc/Ck, a larger initial stress, or a fast loading rate always leads to a rapid consolidation rate. During the unloading period, a negative excess pore water pressure may occur, and a slower unloading rate may reduce this negative value. Copyright © 2014 John Wiley & Sons, Ltd. 相似文献
10.
This paper presents a general semi-analytical solution for undrained cylindrical and spherical cavity expansion in Modified Cam Clay (MCC) and subsequent consolidation. The undrained cylindrical and spherical cavity expansion response in MCC model is obtained through the similarity solution technique. Then, the subsequent consolidation process around the cavity is governed by the classical partial differential equation for consolidation. Finite Difference Method (FDM) is selected for solving the consolidation equation numerically. The proposed semi-analytical solution is validated by comparing the prediction of the dissipations of the pore pressure with Randolph’s closed-form solution for elastic-perfectly plastic soil. Parametric study shows that G0/p0′, R and M have significant influence on the cavity wall excess pore pressure dissipation curve, while it is not sensitive to the value of ν′. It is also found that the negative pore pressure generates around the expanded cylindrical and spherical cavity wall during the consolidation process when R > 5 for typical Boston blue clay. The developed solution has potential applications in geotechnical problems, such as the pile foundation, in-situ test, tunnel construction, compaction grouting, and so forth. 相似文献
11.
Diffusion parameters for HTO, 36Cl−, and 125I− were determined on Upper Toarcian argillite samples from the Tournemire Underground Research Laboratory (Aveyron, France) using the through diffusion technique. The direction of diffusion was parallel to the bedding plane. The purpose of the present study was 3-fold; it was intended (i) to confirm the I− interaction with Upper Toarcian argillite and to verify the effects of initial I− concentration on this affinity, as previously observed by means of radial diffusion experiments, (ii) to highlight any discrepancy between Cl− and I− diffusivity, and (iii) to investigate the effect of an increase of the ionic strength of the solution on the anionic tracers’ diffusive behaviour. The results show that the effective diffusion coefficient (De) and diffusion accessible porosity (εa) values obtained with an ionic strength (I.S.) synthetic pore water of 0.01 eq L−1 are: De = 2.35–2.50 × 10−11 m2 s−1 and εa = 12.0–15.0% for HTO, and De = 14.5–15.5 × 10−13 m2 s−1 and εa = 2.5–2.9% for 36Cl−. Because of anionic exclusion effects, anions diffuse slower and exhibit smaller diffusion accessible porosities than HTO, taken as a water tracer. The associated effective diffusion coefficient (De) and rock capacity factor (α) obtained for 125I are: De = 7.00–8.60 × 10−13 m2 s−1 and α = 4.3–7.2%. Such values make it possible to calculate low 125I distribution ratios (0.0057 < RD < 0.0192 mL g−1) which confirm the trend indicating that the 125I rock capacity factor increases with the decrease of the initial I− concentration. Additional through-diffusion experiments were carried out with a higher ionic strength synthetic pore water (I.S. = 0.11 eq L−1). No evolution of HTO diffusion parameters was observed. The anionic tracers’ effective diffusion coefficient increased by a factor of two but no clear evolution of their accessible porosity was observed. Such a paradox could be related to the particularly small mean pore size of the Upper Toarcian argillite of Tournemire. The most significant finding of this study is the large discrepancy (factor of two) between the values of the effective diffusion coefficient for 125I and 36Cl. Whatever the ionic strength of the synthetic solution used, 125I exhibited De values two times lower than those of 36Cl. A detailed explanation for this difference cannot be given at present even if a hypothesis based on ion-pairing or on steric-exclusion cannot be excluded. This makes questionable the assumption usually made for quantifying 125I sorption and postulating that 36Cl and 125I would diffuse in the same porosity. In other terms, at Tournemire, 125I sorption could be more pronounced than previously indicated. 相似文献
12.
Finite element cavity expansion analysis investigating the effect of penetration rate on piezocone tests in clay is presented. A coupled analysis was performed, in which the rate of cavity expansion was linked to the penetration rate of the cone and the cone angle, using the assumption that the deformation was wholly radial, and took place only between the cone tip and the cone shoulder. The soil was modelled using modified cam clay with two sets of parameters and varying values of overconsolidation ratio (OCR). The influence of penetration rate on the stress and pore pressure distributions was examined. For slower penetration rates, the excess pore pressure at the cone shoulder is lower since consolidation is permitted coincident with penetration. The radial profiles of post‐penetration voids ratio demonstrate that partially drained penetration is permitted by volume change in the near field, in addition to radial movement in the far field. The radial distribution of excess pore pressure after slow penetration differs from the undrained case, with a relatively low radial gradient existing at the cone face. As a result, the dissipation curves after slow penetration lag behind those following fast penetration. The cone velocity is made dimensionless by normalizing with the coefficient of consolidation and the cone diameter. ‘Backbone’ curves of normalized velocity against normalized tip resistance and excess pore pressure capturing the transition from undrained to drained penetration are derived. The normalized pore pressure backbone curve is unique, whilst the normalized tip resistance shows a small dependency on OCR. These backbone penetration curves are compared with centrifuge model piezocone tests conducted at varying rates, and subsequent dissipation tests. The numerical and experimental results suggest that the value of consolidation coefficient operative during the dissipation phase is 2–4 times higher than the virgin compression value due to changes in the operative soil stiffness, as demonstrated from the stress paths of individual soil elements. The use of multi‐rate penetration tests to deduce values of consolidation coefficient is discussed, in light of these differences. Copyright © 2005 John Wiley & Sons, Ltd. 相似文献
13.
天然软土成层分布特性及土中渗流存在起始水力坡降的现象已被人们熟知。但变荷载下能同时考虑黏土中起始水力坡降、软土非线性压缩渗透特性及大应变特性的双层地基固结理论还鲜见报道。在拉格朗日坐标系中建立以超静孔压为变量的双层软土地基大应变非线性固结模型并给出其有限差分解。通过与考虑起始水力坡降的单层地基大应变非线性固结数值计算结果对比,验证了差分解的可靠性。着重分析了上、下土层起始坡降无量纲参数R1、R2对双层地基固结性状的影响,分析在大应变与小应变假定下双层地基超静孔压消散及固结沉降变形的异同。结果表明：上层土无量纲参数R1对双层地基固结性状的影响程度较下层土无量纲参数R2显著;大应变假定下双层地基渗流前锋的下移速度要快于小应变假定下的移动速度;大应变假定下考虑起始水力坡降的双层软土地基超静孔压消散速率要比小应变假定下快,且大应变假定下考虑起始水力坡降的双层地基最终沉降量要比小应变假定下大。 相似文献
14.
《工程地质学报》2017,25(3):605-611
在以往对非饱和土砂井地基固结理论研究中,均将涂抹区与非涂抹区土体渗透系数视为相等,这与实际工程并不相符。本文将考虑涂抹区土体渗透系数的变化,分析其对超孔隙气、水压力消散规律的影响。基于Fredlund一维固结理论以及Darcy定律和Fick定律,对有限厚度线弹性非饱和土砂井地基,在大面积均布瞬时荷载作用下,考虑涂抹区土体渗透系数的变化,利用Laplace变换并引入Bessel函数推导出Laplace变换下的解,再通过Crump方法编程实现Laplace逆变换得到超孔隙气压力、超孔隙水压力的半解析解。利用典型算例进行计算,分别得到在不同半径、不同涂抹区半径和不同涂抹程度的情况下,超孔隙气压力、超孔隙水压力随时间的变化规律。得出考虑涂抹作用时,超孔隙气、水压力的消散速度降低;涂抹区半径越大、涂抹程度越高速度越慢,反之消散越快。本研究丰富了非饱和土砂井固结理论,对非饱和土砂井固结特性的研究具有一定的工程参考价值。 相似文献
15.
A closed form analytical solution for two‐dimensional plane strain consolidation of unsaturated soil stratum 
下载免费PDF全文
下载免费PDF全文 This paper discusses the excess pore‐air and pore‐water pressure dissipations and the average degree of consolidation in the 2D plane strain consolidation of an unsaturated soil stratum using eigenfunction expansion and Laplace transformation techniques. In this study, the application of a constant external loading on a soil surface is assumed to immediately generate uniformly or linearly distributed initial excess pore pressures. The general solutions consisting of eigenfunctions and eigenvalues are first proposed. The Laplace transform is then applied to convert the time variable t in partial differential equations into the Laplace complex argument s. Once the domain is obtained, a simplified set of equations with variable s can be achieved. The final analytical solutions can be computed by taking a Laplace inverse. The proposed equations predict the two‐dimensional consolidation behaviour of an unsaturated soil stratum capturing the uniformly and linearly distributed initial excess pore pressures. This study investigates the effects of isotropic and anisotropic permeability conditions on variations of excess pore pressures and the average degree of consolidation. Additionally, isochrones of excess pore pressures along vertical and horizontal directions are presented. It is found that the initial distribution of pore pressures, varying with depth, results in considerable effects on the pore‐water pressure dissipation rate whilst it has insignificant effects on the excess pore‐air pressure dissipation rate. Copyright © 2015 John Wiley & Sons, Ltd. 相似文献
16.
沉桩引起的超静孔隙水压力消散是产生管桩极限承载力时效性的主要因素之一。结合天津东疆保税港区物流加工区二期工程,利用有限元模拟分析沉桩后超孔压的消散规律及管桩的极限承载力随时间变化的规律,提出吹填土中管桩时效承载力公式供工程参考使用,并进行吹填土现场各测点沉桩过程及沉桩后孔隙水压力的监测,验证模拟结果的同时探讨超静孔隙水压力的分布及消散规律。模拟得到沉桩后桩底超孔压随时间消散, 20d后消散率达到97%; 管桩的时效承载力随时间增长,并与超孔压的消散有着明显的对应关系; 得到吹填土中管桩承载力的时效公式以供工程参考使用。现场孔压监测表明深度增加,超孔压增大; 离桩越近,超孔压越大; 土层渗透系数越小,超孔压消散越慢。施工对土体的有效影响范围为9~10倍桩径。 相似文献
17.
The excess pore water pressure distribution (u) induced by the penetration of a piezocone into clay and its dissipation behaviour have been investigated by laboratory model tests, theoretical analysis and numerical simulation. Based on the results of the tests and the analysis, a semi-theoretical method has been proposed to predict the piezocone penetration-induced pore pressure distribution in the radial direction from the shoulder of the cone. The method can consider the effect of the undrained shear strength (su), over-consolidation ratio (OCR) and rigidity index (Ir) of the soil. With a reliably predicted initial distribution of u and the measured curve of dissipation of pore water pressure at the shoulder of the cone (u2), the coefficient of consolidation of the soil in the horizontal direction (ch) can be back-fitted by analysis of the pore pressure dissipation. Comparing the back-fitted values of ch with the values directly estimated by a previously proposed method indicates that the previously proposed method can be used reliably to estimate ch values from non-standard dissipation curves (where u2 increases initially and then dissipates with time). 相似文献
18.
The coefficient of consolidation is one of the most important parameters that control the rate of consolidation. Conventional consolidation theories assume that the coefficient of consolidation is constant during the whole consolidation process. In the case of sensitive clay, the coefficient of consolidation is strongly dependent on the level of effective stress of clay. With the dissipation of pore water pressure and the increase of effective stress, the soil structure of the upper subsoil is gradually destroyed downwards and its coefficient of consolidation becomes smaller. At the same time, the coefficient of permeability of the vertical drains drops down because of the kinking or bending effect. The destructured upper subsoil and the kinking of the vertical drain hinder the dissipation of the pore pressure in the lower subsoil. This paper presents a model to describe the above important phenomena during the consolidation of sensitive clay with vertical drain. The solution for proposed model can be obtained by extending the closed‐form solution of the consolidation of double‐layered ground with vertical drain by the interactive method introducing the concept of the moving boundary and the reduction of discharge capacity of vertical drain. The numerical results obtained from the finite element method package PLAXIS (Ver. 7.2) are adopted to compare those obtained from the present algorithm. Moreover, the rationality of the moving boundary is explained by the distributions of the excess pore water pressure in natural soil zone along the radial direction. Wenzhou airport project is taken as a case study in this paper. The results for the sensitive soil with decaying sand drain agree very well with the in situ measured data. The calculated results can properly explain two general phenomena observed in the consolidation of soft sensitive soil ground with vertical drains: one is that the time to achieve the same consolidation degree is much longer under heavy loading than that under light loading; the other is that the consolidation speed is much slower in the lower subsoil than in the upper subsoil. Finally, it is indicated that the vertical drains can decrease the hindrance effect of the destructured subsoil. Copyright © 2007 John Wiley & Sons, Ltd. 相似文献
19.
在底部可测孔压的固结仪内进行单面排水固结试验时,观测到试样底部的孔压可出现滞后现象。为分析其原因,考虑加载引起的动力效应,建立以竖向应变为求解对象的一维动力固结方程,并用有限差分法进行求解。引入新指标CD来综合考虑试样压缩模量、渗透系数、密度以及土样厚度等4个参数对动力效应的影响,探讨了该指标对固结过程中孔隙水压力的影响。计算结果表明,瞬时加载引起的动力效应是引起试样内孔压滞后的一个原因,并且对于压缩模量或渗透系数较大的试样,更易出现孔压滞后现象,同时动力效应对固结度的影响则主要体现在固结的前期。最后讨论了固结分析时可以忽略动力效应的范围。 相似文献