首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 390 毫秒
1.
This study reports the potential ability of non-living biomass of Cabomba caroliniana for biosorption of Cr(III) and Cr(VI) from aqueous solutions. Effects of contact time, biosorbent dosage, pH of the medium, initial concentration of metal ion and protonation of the biosorbent on heavy metal–biosorbent interactions were studied through batch sorption experiments. Cr(III) was sorbed more rapidly than Cr(VI) and the pH of the medium significantly affected the extent of biosorption of the two metal species differently. Surface titrations showed that the surface of the biosorbent is positively charged at low pH while it is negatively charged at pH higher than 4.0. Protonation of the biosorbent increased its capacity for removal of Cr(III), while decreasing that of Cr(VI). FT-IR spectra of the biosorbent confirmed the involvement of –OH groups on the biosorbent surface in the chromium removal process. Kinetic and equilibrium data showed that the sorption process of each chromium species followed pseudo second-order kinetic model and both Langmuir and Freundlich isothermal models. A possible mechanism for the biosorption of chromium species by non-living C. caroliniana is suggested.  相似文献   

2.
Adsorption of hexavalent chromium from aqueous solutions by wheat bran   总被引：7，自引：6，他引：1  
In this research, adsorption of chromium (VI) ions on wheat bran has been studied through using batch adsorption techniques. The main objectives of this study are to 1) investigate the chromium adsorption from aqueous solution by wheat bran, 2) study the influence of contact time, pH, adsorbent dose and initial chromium concentration on adsorption process performance and 3) determine appropriate adsorption isotherm and kinetics parameters of chromium (VI) adsorption on wheat bran. The results of this study showed that adsorption of chromium by wheat bran reached to equilibrium after 60 min and after that a little change of chromium removal efficiency was observed. Higher chromium adsorption was observed at lower pHs, and maximum chromium removal (87.8 %) obtained at pH of 2. The adsorption of chromium by wheat bran decreased at the higher initial chromium concentration and lower adsorbent doses. The obtained results showed that the adsorption of chromium (VI) by wheat bran follows Langmuir isotherm equation with a correlation coefficient equal to 0.997. In addition, the kinetics of the adsorption process follows the pseudo second-order kinetics model with a rate constant value of 0.131 g/mg.min The results indicate that wheat bran can be employed as a low cost alternative to commercial adsorbents in the removal of chromium (VI) from water and wastewater.  相似文献   

3.
The batch removal of Cr(VI) from aqueous solution using lignocellulosic solid wastes such as sawdust and pine leaves under different experimental conditions was investigated in this study. The influence of pH, temperature, contact time, initial concentration of Cr(VI) and particle size on the chromium removal was investigated. Adsorption of Cr(VI) is highly pH-dependent and the results indicate that the optimum pH for the removal is 2. The capacity of chromium adsorption at equilibrium by these natural wastes increased with absorbent concentration. Temperature in the range of 20–60 °C showed a restricted effect on the adsorption capacity of pine leaves, but had a considerable effect on the adsorption capacity of sawdust. The capacity of chromium adsorption at the equilibrium increased with the decrease in particle sizes. The suitability of adsorbents was tested with Langmuir and Freundlich isotherms and their constants were evaluated. Results indicated that the Freundlich model gave a better fit to the experimental data in comparison with the Langmuir equation. The study showed that lignocellulosic solid wastes such as sawdust and pine leaves can be used as effective adsorbents for removal of Cr(VI) from wastewater.  相似文献   

4.
A novel adsorbent for heavy metal remediation in aqueous environments   总被引：9，自引：8，他引：1  
The objective of this study was to investigate the possibility of using maize tassel as an alternative adsorbent for the removal of chromium (VI) and cadmium (II) ions from aqueous solutions. The effect of pH, solution temperature, contact time, initial metal ion concentration and adsorbent dose on the adsorption of chromium (VI) and cadmium (II) by tassel was investigated using batch methods. Adsorption for both chromium (VI) and cadmium (II) was found to be highly pH dependent compared to the other parameters investigated. Obtained results gave an adsorption capacity of 79.1 % for chromium (VI) at pH 2, exposure time of 1h at 25 °C. Maximum capacity of cadmium of 88 % was obtained in the pH range of 5-6 at 25 °C after exposure time of 1 h. The adsorption capacities of tassel for both chromium (VI) and cadmium (II) were found to be comparable to those of other commercial adsorbents currently in use for the removal of heavy metals from aqueous wastes. These results have demonstrated the immense potential of maize tassel as an alternative adsorbent for toxic metal ions remediation in polluted water and wastewater.  相似文献   

5.
Barium ion cross-linked alginate beads have shown great affinity to toxic hexavalent chromium ions in aqueous solution, in contrast to the traditionally used calcium alginate beads. Our adsorption experiments were carried out by the batch contact method. The optimal pH for removal was found to be pH 4. The equilibrium was established in 4 h, and the removal efficiency of chromium(VI) was found to be 95 %. The adsorption data were applied to Langmuir, Freundlich, Dubinin–Redushkevich (D–R), and Temkin isotherm equations. Both Langmuir and Freundlich isotherm constants indicated a favorable adsorption. The value of mean sorption energy calculated from D–R isoterm indicates that the adsorption is essentially physical. The high maximum chromium(VI) adsorption capacity was determined from the Langmuir isotherm as 36.5 mg/g dry alginate beads. The chromium(VI) adsorption data were analyzed using several kinetic models such as the pseudo-first-order, pseudo-second-order, intraparticle diffusion, and Elovich models, and the rate constants were quantified. Our study suggests that barium alginate beads can be used as cost-effective and efficient adsorbents for the removal of chromium(VI) from contaminated waters.  相似文献   

6.
This paper presents the removal of hazardous hexavalent chromium from liquid waste streams using divinylbenzene copolymer resin Amberlite IRA 96. Important sorption parameters such as contact time, pH, resin dosage and initial metal concentration were studied at 30?°C. The kinetic study was conducted using pseudo-first and pseudo-second-order kinetics at 30?°C. The sorption process was found to be pH dependent. Maximum removal was obtained at pH 2 under optimized conditions. The sorption process was rapid and 99?% of the removal was achieved in first 30?min. The equilibrium data were fitted to both Langmuir and Freundlich models. The better regression coefficient (R 2) in Freundlich model suggests the multilayer sorption process. The value of Gibbs free energy for sorption process was found to be ?12.394?kJmol?1. The negative value indicated the spontaneity of the sorption process. Scanning electron microscope and energy dispersive X-ray spectroscopy studies were conducted to find the role of surface morphology during sorption process. The Fourier transform infrared study was conducted to identify the functional groups responsible for interaction between the resin and chromium. Desorption and regeneration studies were also carried out.  相似文献   

7.
The biosorption of chromium (VI) ions from aqueous solutions by two adsorbents viz. mango and neem sawdust was studied under a batch mode. An initial pH of 2.0 was most favorable for chromium (VI) removal by both the adsorbents. The results obtained for the final concentration of chromium (VI) and chromium (DI) at a pH range of 2–8 indicated that a combined effect of biosorption and reduction was involved in the chromium (VI) removal specially when the pH value is lower than 3. The maximum loading capacity was calculated from adsorption isotherms by applying the Langmuir model and found to be higher for neem sawdust (58.82 mg/g). Evaluation of experimental data in terms of biosorption kinetics showed that the biosorption of chromium (VI) by neem sawdust followed pseudo second-order kinetics. Therefore, the rate limiting step may be chemical sorption or chemisorption. The efficiency of this process was examined in using tannery wastewater contaminated with chromium (VI) ions in column mode.  相似文献   

8.
Adsorption of chromium and copper in aqueous solutions using tea residue   总被引：5，自引：3，他引：2  
In this study, adsorption of copper and chromium was investigated by residue of brewed tea (Tea Waste) from aqueous solutions at various values of pH. It was shown that adsorbent dose, copper and chromium ion concentrations in such solutions influence the degree of these heavy metal ions’ obviation. The adsorption level of the prepared solutions was measured by visible spectrophotometer. The tea residue adsorbed copper (II) and chromium (VI) ions at initial solution pH by 25 % and 3 %, respectively. During the experiments the peak adsorption occured in hydrated copper nitrate aqueous solution at pH range of 5–6. Likewise the maximum adsorption appeared in potassium chromate aqueous solution at pH range of 2–3. In addition, tea residue adsorbed about 60 mg/g of copper (II) ion at pH=5, while chromium adsorption was registered at about 19 mg/g at pH=2. The data obtained at the equilibrium state, was compared with Langmuir and Freundlich models. Results showed that regarding the kinetics of adsorption, the uptake of copper (II) and chromium (VI) ions by tea residue was comparatively faster, with the adsorption process exhaustion completed within the first 20 min of the experiments. Furthermore, results revealed that adsorption data concerning the kinetic phase is closely correlated with a pseudo-second order model with R2> 0.99 for copper (II) and chromium (VI) ions  相似文献   

9.
Chromium (VI) which exists in many industrial wastewater is considered highly toxic. The aim of the present investigation was to study the reduction of chromium (VI) to chromium (III) and then removing it with the help of weathered basalt andesite products. Reduction of the chromium (VI) to chromium (III) by hydrazinium sulfate was investigated. The influence of hydronium ion concentration, contact time, hydrazinium sulphate dosage and temperature has been tested in batch runs. The process was found to be acid, temperature and concentration dependent. The suitability of weathered basalt andesite products as a potential sorbent was assessed for the removal of chromium (III) following batch mode of operation. The effect of various parameters such as hydronium ion concentration, shaking time, sorbent dose, initial metal ion concentration and temperature on the removal of chromium (III) from aqueous solution was studied. Thermodynamic parameters (?H°, ?S° and ?G°) for the sorption process were evaluated. Analysis of sorption obtained results showed that the sorption pattern followed the Freundlich, Langmuir and Dubinin-Kaganer-Radushkevich isotherms. The process follows pseudo second order rate and surface diffusion is identified as the predominating mechanism. The sorption process was shown to be reversible by the recovery of sorbed chromium (III) upon extraction with 0.5 M nitric acid. The sorbent, before and after sorption, was characterized by fourier transform infrared spectrometer, X-ray diffraction, scanning electron microscope, transmision electron microscope and thermogravimetric analyse methodes. An increase in crystallanity after sorption of chromium was observed. An industrial effluent was successfully treated with the same sorbent with convincing results.  相似文献   

10.
The goal of this study is examination of the mixture between adsorption and permeation process for removing chromium (VI) from the water. Two types of supported membranes are developed: The first one which was made by sol–gel method is called nanoporous and the second one which was made by electrospinning is called nanofiber. The sorption capacity of nanoporous and nanofiber is examined in single batch experiments at various pH values, and it is found that maximum chromium removal is observed for both nanoporous and nanofiber at pH 3.5. Adsorption studies illustrated that the Cr(VI) adsorption onto alumina nanoporous and nanofiber is affected by changes in pH, contact time, dosage of adsorbent, concentration of chromium and solution volume. Langmuir and Freundlich isotherms can be used to explain the adsorption equilibria of Cr(VI) onto alumina nanoporous and nanofiber. It was found that balance adsorption data adequate Langmuir isotherm more than Freundlich model. Adsorption kinetics was found to be fitted to pseudo-second order and Weber and Morris model. The output of multiple linear regressions was run for the second-order response surface model implied that the linear agents of pH, sorbent dosage and Cr(VI) concentration are more significant factors. Manufacturing electrospun alumina nanofiber and sol–gel nanoporous with these cheap materials, renewable and fast methods are so important although the removal percentage is significant.  相似文献   

11.
Adsorption characteristics of water hyacinth roots powder for the removal of Indosol Dark-blue GL dye were investigated in batch mode. Operating variables, such as initial solution pH, presence of detergent, adsorbent dosage, initial concentration and contact time, were studied. The results showed that the adsorption of dye increased with increasing the initial concentration and contact time. The adsorption is highly pH dependent and adsorption capacity increased with decrease in pH. Kinetic study revealed that the uptake of Indosol Dark-blue GL was very rapid within the first 15 min and equilibrium time was independent of initial concentration. Batch equilibrium experiments were carried out at different pH and found that equilibrium data fitted well to Langmuir isotherm model. The maximum sorption capacity of the adsorbent was found as 86 mg g?1 at pH 3 which reduced to 64 mg g?1 at pH 5. The presence of detergent reduced the sorption capacity of the adsorbent significantly. Using equilibrium and kinetic data, the forward and backward rate constants were determined from the unified approach model. Desorption study revealed that the dye can be recovered by swing the pH from low to high.  相似文献   

12.
The present study reports on the preliminary investigation of three low-cost natural materials with respect to their chromium(VI) removal efficiency from contaminated water. The tested materials were reed, in milled and chopped form, compost, and dewatered sludge from a municipal wastewater treatment plant. The chromium(VI) removal capacity of the aforementioned materials was investigated by simulating the physicochemical conditions prevailing in a stormwater outfall flowing into the Asopos River in Inofyta, Central Greece. Thus, batch and column experiments were carried out using solutions of 3–5 mg/L chromium(VI) and pH value 8.5 ± 0.5. The results showed that the tested materials were capable of removing 3 mg/L chromium(VI), however by allowing different contact times for each material. The chromium(VI) removal kinetics were studied through batch experiments, and reed was found to be the most efficient material. Therefore, at a second series of batch and up-flow column experiments, the effect of the liquid-to-solid ratio, pH, and contact time on chromium(VI) removal using chopped reed was investigated. Chromium(VI) removal took place through both reduction and adsorption mechanisms, while the released soluble organic matter from reed seemed to favor the reduction mechanism. As a result, reed is a potential biosorbent capable of treating heavily chromium(VI)-contaminated water flows, although a high mass of reed is required for a treatment process, such in the case of the stormwater discharged into Asopos River.  相似文献   

13.
An investigation was undertaken regarding the adsorption of different heavy metal ions from aqueous solutions using ??-diketone-functionalized styrene divinylbenzene resin under different experimental conditions such as initial concentration of metal ions, contact time, pH, and chelating capacity. The functionalization of resin was carried out by the condensation reaction of sodium salt of ??-diketones (pentane-1,3-dione) and chloromethylated styrene?Cdivinylbenzene resin in dichloromethane. Functionalized resin beads were characterized by Fourier transform infrared spectroscopy. The batch method was employed using different metal ions solution from 5 to 15?mg/L at different contact times. The adsorption kinetics was tested for the pseudo-first order, pseudo-second order reaction at different experimental conditions. The rate constant of adsorption kinetic models were also calculated and good correlation coefficient (R 2?>?0.9941) was obtained for pseudo-second order kinetic model. The maximum adsorption value obtain for lead (0.725728?mg/g), chromium (0.9199?mg/g), nickel (0.4974?mg/g), cobalt (0.6196?mg/g) and cadmium (0.6519?mg/g) at equilibrium condition, which shows that ??-diketone-functionalized styrene divinylbenzene resin is an effective adsorbent for toxic metal ions.  相似文献   

14.
Adsorption and desorption of uranium(VI) from dilute aqueous solutions by Eucalyptus citriodora distillation sludge was studied in a batch mode. The potential of Eucalyptus citriodora distillation sludge to remove uranium(VI) from aqueous solutions has been investigated at different conditions of solution pH, metal ion concentrations, biosorbent dosage, biosorbent particle size, contact time and temperature. The results indicated that biosorption capacity of Eucalyptus citriodora distillation sludge was strongly affected by the medium pH, the biosorbent dose, metal ion concentrations and medium temperature. Reduction in particle size increased the biosorption capacity. Langmuir and Freundlich isotherm models were applied to biosorption data to determine the biosorption characteristics. An optimum biosorption capacity (57.75 mg/g) was achieved with pH 4.0, particle size 0.255 mm, biosorbent dose 0.5 g/100 mL and initial uranium(VI) concentration of 100 mg/L. Uranium(VI) removal by Eucalyptus citriodora distillation sludge was rapid, the equilibrium was established within 60 min and pseudo-second-order model was found to fit with the experimental data. The biosorption process decreased with an increase in the temperature indicating its exothermic nature. Pretreatments of biomass with different reagents affected its biosorption capacity. A significant increase (34 %) in biosorption capacity (83.25 mg/g) was observed with benzene treatment. Fourier-transform infra-red studies showed the involvement of carbonyl, carboxyl and amide groups in the biosorption process. The results indicated that sulfuric acid had the best effects as an eluent showing 93.24 % desorption capacity.  相似文献   

15.
A new organic–inorganic composite cation exchanger polyaniline Sn(IV) silicate has been synthesized. The physicochemical properties of this ion exchanger were determined using different analytical techniques including fourier transform infrared spectroscopy, simultaneous thermogravimetry–differential thermogravimetry analyses, X-ray diffraction, scanning electron microscopy, energy-dispersive X-ray spectroscopy and elemental analysis studies. Ion exchange capacity and effect of heating temperature on ion exchange capacity were also carried out on this ion exchange material. Adsorption properties for different metal ions have been investigated and the results revealed that polyaniline Sn(IV) silicate had the highest adsorption capacity for Cd2+ ion. It’s selectivity was tested by achieving some important binary separations. Dependence of adsorption on contact time, temperature, pH of the solution and exchanger dose had been studied to achieve the optimum conditions. Adsorption kinetic study showed that the adsorption process followed the first order kinetics. Adsorption data were fitted to linearly transformed Langmuir isotherm with R 2 (correlation coefficient) >0.99. The maximum removal of Cd2+ was found at pH 9. The adsorption was fast and the equilibrium established within 40 min. Thermodynamic parameters viz- entropy change, enthalpy change and Gibb’s free energy change were also calculated.  相似文献   

16.
In the present study, the retention capacity of carbonaceous material obtained from the diesel engine exhaust mufflers for Cr(VI) removal has been investigated. The physicochemical properties such as density, pH of aqueous slurry, pH at point of zero charge, ash content, moisture content, volatile matter, surface area, scanning electron microscopy and electron dispersive spectroscopy of the carbonaceous material were determined. The capacity of adsorbent for removal of Cr(VI) from aqueous solution was observed under different experimental condition like contact time, initial concentration of metal ions, pH and temperatures on the adsorption capacity of the adsorbent. Maximum adsorption of Cr(VI) ions was found at low pH. The adsorption process was found to follow second-order kinetics. The rate constant was evaluated at different temperatures along with other thermodynamic parameters like activation energy, Gibbs free energy change, enthalpy change and entropy change. Both Langmuir and Freundlich isotherms were used to describe the adsorption equilibrium of carbonaceous material at different temperatures. Langmuir isotherm shows better fit than Freundlich isotherm at given conditions. The result shows that low-cost carbonaceous material from diesel engine exhaust mufflers can be efficiently used for wastewater treatment containing Cr(VI) ions.  相似文献   

17.
The development of a fast, effective, simple and low-cost procedure for chromium speciation is an analytical challenge. In this work, a new and simple method for speciation and determination of chromium species in different matrices was developed. Sepia pharaonis endoskeleton nano-powder was used as an adsorbent for the dispersive micro-solid-phase extraction. Finally, the desorbed chromium was determined using a graphite furnace atomic absorption spectrometer. The experimental results showed that Cr(III) could be quantitatively extracted by the adsorbent, while Cr(VI) adsorption was negligible. Concentrated H2SO4 and ethanol reduced Cr(VI)–Cr(III), and total chromium content was assessed as Cr(III). Then, the Cr(VI) concentration in the sample was calculated as the difference. The optimum conditions were obtained in terms of pH, adsorbent amount, contact time, and type, concentration and volume of eluent. Under the optimum conditions that involved the speciation of chromium ions from 25 mL of the water samples at pH 7.0 using 0.025 g of the adsorbent with contact time of 5 min, the method was validated in terms of linearity, precision and accuracy. The calibration curve was linear over the concentration range of 0.01–25.00 μg L?1 for Cr(III). The obtained limit of detection for the proposed method was 0.003 µg L?1. The maximum adsorption capacity of the adsorbent was found to be 995.57 mg g?1. The proposed method was validated by the speciation of Cr(III) and Cr(VI) in different real water and wastewater samples with satisfactory results.  相似文献   

18.
Kinetics and equilibrium study of chromium adsorption on zeoliteNaX   总被引：2，自引：1，他引：1  
This study aims to report Batch adsorption study of hexavalent chromium, Cr (VI) on zeoliteNaX. Kinetics of Cr (VI) adsorption and adsorption isotherms were determined by varying operating parameters such as pH, initial concentration, temperature and contact time. ZeoliteNaX was found to remove Cr (VI) in acidic solutions down to ppm level at pH of about 4. Removal rate of Cr (VI) was found to decrease as pH rises above 4.0. Langmuir, Freundlich, Temkin and Redlich-Peterson models were applied to adsorption equilibrium data to find the best amongst these models. Langmuir model with R2 = 0.9711 best fits the adsorption data. The kinetics of adsorption was found to follow the first order reversible reaction. The separation parameter, RL values of less than 1.0 i.e., 0.7369, 0.5834 and 0.4828 corresponding to initial concentrations of 10, 20 and 30 mg/L, respectively indicated that adsorption of Cr (VI) on zeoliteNaX is favoured. The estimated values of thermodynamic parameters such as heat of adsorption and standard gibbs free energy confirmed the exothermic nature of adsorption of Cr (VI) on zeoliteNaX.  相似文献   

19.
In this study, the adsorption behavior of Ni(II) in an aqueous solution system using natural adsorbent Peganum harmala-L was measured via batch mode. The prepared sorbent was characterized by scanning electron microscope, Fourier transform infrared spectroscopy, N2 adsorption–desorption and pHzpc. Adsorption experiments were carried out by varying several conditions such as contact time, metal ion concentration and pH to assess kinetic and equilibrium parameters. The equilibrium data were analyzed based on the Langmuir, Freundlich, Temkin and Dubinin–Radushkevich isotherms. Kinetic data were analyzed using the pseudo-first-order, pseudo-second-order and intra-particular diffusion models. Experimental data showed that at contact time 60 min, metal ion concentration 50 mg/L and pH 6, a maximum amount of Ni(II) ions can be removed. The experimental data were best described by the Langmuir isotherm model as is evident from the high R 2 value of 0.988. The adsorption capacity (q m) obtained was 68.02 mg/g at an initial pH of 6 and a temperature of 25 °C. Kinetic studies of the adsorption showed that equilibrium was reached within 60 min of contact and the adsorption process followed the pseudo-first-order model. The obtained results show that P. harmala-L can be used as an effective and a natural low-cost adsorbent for the removal of Ni(II) from aqueous solutions.  相似文献   

20.
This study describes the development of scallop shell synthesized ceramic biomaterial for phosphorus removal from water. The synthesized biomaterial was characterized by scanning electron microscope, Brunauer–Emmett–Teller and X-ray diffractometer methods. The influences of contact time, initial phosphate concentration, initial solution pH, co-existing ions and temperature for phosphorus removal were investigated by batch experiments. The results indicated that the equilibrium data can be fitted by the Langmuir isotherm model at temperatures ranging from 15 to 55 °C, with the maximum sorption capacity of 13.6 mg/g. Sorption kinetics followed a pseudo-second-order kinetic equation model. The sorption process was optimal at a wide range of solution pH (above 2.4), with a relatively high sorption capacity level. Phosphorus sorption was slightly impeded by the presence of F?, HCO3 ? and NH4 + ions, and significantly inhibited by Cl?, SO4 2? and NO3 ? ions. Sorption process appeared to be controlled by a chemical precipitation processes. The mechanism may be attributed to ion complexation during subsequent sorption of phosphorus on scallop shell synthesized ceramic biomaterial.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号