首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 62 毫秒
1.
Re-Os同位素体系已成为金属矿床定年和示踪的重要手段之一。文章在简述Re-Os同位素体系基本原理基础上,综述了国内外的最新研究成果,认为Re-Os同位素测试对象不再局限于辉钼矿和铜镍硫化物矿石,黄铁矿、毒砂、磁黄铁矿、镍黄铁矿、闪锌矿等也常作为测试对象用于金矿床、铅锌矿床、沉积喷流型钴(金)等矿床的定年。地壳岩石与原始地幔相比,具有较高的187 Os/188 Os比值、γOs值以及Re/Os比值,因此,硫化物或矿石的Re-Os同位素组成和普通Os—Re/Os比值图解可以揭示斑岩矿床、金矿、铅锌矿以及铜镍硫化物矿的成矿物质来源。辉钼矿则可以通过Re含量来示踪成矿物质来源。Re-Os同位素也可与其他同位素结合(如187 Os/188 Os-87Sr/86Sr)共同判明不同端元组分对成矿的贡献。  相似文献   

2.
天宇岩浆铜镍硫化物矿床的矿体由浸染状矿体和块状矿体组成。采用同位素稀释Triton-plus测定了浸染状矿石和块状矿石的磁黄铁矿Re-Os同位素比值。结果表明:浸染状矿石w(Re)为11.82×10~(-9)~45.28×10~(-9),w(Os)为0.944×10~(-9)~8.528×10~(-9),187Os/188Os初始比值为0.885~2.332,γOs为607~1763;块状矿石w(Re)为49.38×10~(-9)~315.10×10~(-9),w(Os)为0.191×10~(-9)~42.420×10~(-9),187Os/188Os初始比值为0.654~3.322,γOs为423~2555。Re、Os含量、同位素组成和特征值表明,该矿床物质为壳-幔混合来源,块状矿石可能比浸染状矿石经历了更强的地壳物质混染。浸染状矿体发育透闪石化、蛇纹石化、绿泥石化蚀变,表明存在岩浆期后热液活动,但块状矿体热液蚀变不明显,块状矿石的Re-Os同位素特征可能是与地壳岩石直接作用的结果。地壳混染作用发生在深部岩浆房,同时也发生在岩浆侵位及再次迁移过程中,这些过程造成块状矿体与浸染状矿体不同的同位素特征。  相似文献   

3.
通过对天宇铜镍硫化物矿石中的硫化物Re-Os同位素物质来源示踪研究,其187Os/188Os初始比值为0.864 9~2.910 6,γOs位于592~884之间,γOs平均值为832.5,说明在成矿过程中仅有大量地壳物质混染加入到岩浆和成矿系统之中;根据天宇岩体的岩石地球化学特征,并结合东天山东段基性一超基性岩体的空间分布特征,认为该岩体形成于洋内俯冲的增生岛弧环境,是晚古生代北天山洋壳向南俯冲增生的产物。  相似文献   

4.
新疆喀拉通克铜镍硫化物矿床Re-Os同位素研究及其地质意义   总被引:18,自引:0,他引:18  
喀拉通克铜镍硫化物矿石的Re-Os同位素测年结果为305±15(2σ)Ma。该数据表明产于阿尔泰山南缘的铜镍硫化物矿床形成于晚石炭世一早二叠世,与区内广泛发育的造山型金矿和浅成低温热液型金矿基本为同一时期。其等时线~187Os/~188Os初始比值为0.35±0.04,γ_Os仉值平均为183,表明在成矿过程及岩浆侵位期间有少量地壳物质加入成矿系统中。  相似文献   

5.
新疆哈密月牙湾铜镍矿是近年来在东天山卡拉塔格地区新发现的岩浆型铜镍硫化物矿床.为确定该矿床的成岩、成矿时代及其成矿作用,利用锆石LA-ICP-MS U-Pb定年和硫化物Re-Os同位素等时线定年方法,分别对主含矿岩相橄榄辉长岩和矿石中的磁黄铁矿进行了年龄测定.橄榄辉长岩中锆石的206Pb/238U年龄为255~292 Ma,加权平均值为274±2.4 Ma,代表了橄榄辉长岩的成岩年龄;矿石中磁黄铁矿Re-Os同位素等时线年龄为271.9±9.5 Ma,代表了硫化物熔离成矿的年龄;187Os/188Os初始值为0.279 6±0.008 9,γOs值为117~126,指示在岩浆侵位及硫化物熔离成矿过程中有地壳物质加入.月牙湾镁铁质岩浆的成岩、成矿作用发生于早二叠世,与东天山黄山-图拉尔根一带典型铜镍硫化物矿床为同一时期的产物.   相似文献   

6.
力马河镍矿Re-Os同位素研究   总被引:10,自引:0,他引:10  
陶琰 《地质学报》2008,82(9):1292-1304
四川力马河镍矿是峨眉山大火成岩省一个重要的岩浆硫化物矿床。本文通过对其主要岩、矿石类型Re、Os及其同位素组成的分析,综合探讨了成矿岩体原始岩浆性质、矿石硫化物成因、成矿机制及Re-Os同位素等时线年龄。结果表明,力马河镍矿不同类型岩矿石样品初始Os同位素组成是不均一的,富硫化物的网脉状矿石及其选纯硫化物Os同位素组成初值差异较小,其等时线年龄为265±35 Ma、与岩体锆石SHRIMP年龄263±3 Ma基本相当;硫化物含量较低的岩、矿石样品间初始Os同位素组成差异较大,其表观等时线年龄大于成矿年龄。分析认为,岩矿样品初始Os同位素组成的不均一是由含较高放射成因187Os丰度的硫化物熔体和含较低放射成因187Os丰度的硅酸盐熔体不同比例混合造成的。混合模型分析表明,硫化物含量超过30%的矿石样品初始187Os/188Os基本接近,硫化物含量低于30%的岩矿石样品初始187Os/188Os随硫化物含量上的不同差异很大,为岩浆硫化物矿床Re-Os等时线年龄可能出现多组年龄解的现象提供了一种可能的解释。成矿岩体中含放射成因187Os丰度最低的岩石样品γOs(t=260Ma)在5左右、Cu/Pd比值在7000左右,表明是基本没有受到地壳混染及硫化物熔离影响的原始岩浆结晶分异产物,估计原始岩浆Os含量在1×10-9左右,为苦橄质岩浆。矿石硫化物Re/Os比值显著高于任何赋矿橄榄岩,γOs(t=260Ma)高达110左右,综合分析揭示了力马河镍矿硫化物为二次熔离成因,模式分析认为,矿石硫化物是由原始岩浆经历R=2000左右的硫化物熔离后、其亏损岩浆再经R=200左右的硫化物熔离形成,与二次熔离相对应,成矿岩浆也经历了两次混染作用,分别为上、下地壳7%左右的混染。  相似文献   

7.
通过对葫芦铜镍硫化物矿石的Re-Os同位素物质来源示踪研究, 其187Os/188Os初始比值介于1.40~1.97,γOs值介于1110~1565,平均为1379, 表明在成矿过程及岩浆侵位期间有大量地壳物质加入到成矿系统中。  相似文献   

8.
金宝山和白马寨铜镍硫化物矿床均主要赋存在峨眉山大火山岩省中,但其矿化特征存在许多不同。本文着重对比了金宝山铂钯矿床和白马寨铜镍矿床的铂族元素(PGE)地球化学特征,发现前者表现为高ΣPGE及低的(Cu Ni)、Pd/Ir(3.84~26.49)、Cu/Pd(46.91~1309.58)值和Au/Pd值,相反,后者表现为低ΣPGE、高(Cu Ni)、Pd/Ir(4.72~297.2)、Cu/Pd(10875.13~974788.55)值和较高的Au/Pd值。金宝山和白马寨PGE原始地幔标准化配分模式均主要表现为左倾型,但二者表现为镜像关系。金宝山较白马寨的PGE间相关性好,可能说明白马寨母岩浆经历了较为复杂的地质过程,其铂族元素体系因此受到较大的扰动。结合前人有关杨柳坪铜镍铂族元素矿床的铂族元素数据,认为峨眉地幔柱形成铜镍铂族元素矿床大致可以分成3个阶段:1金宝山阶段:即为S的低度饱和阶段,为峨嵋地幔柱上升初期,吸收少量壳源物质,由于PGE在硫化物中很高的分配系数,导致少量硫化物熔体从硅酸盐中萃取大量PGE和少量Cu-Ni熔离出来,与铬铁矿、橄榄石和辉石等,于高温下结晶分异堆积而成金宝山岩体,形成独立铂钯矿床。...  相似文献   

9.
采用镍硫火试金ICP-MS法分析了白马寨铜镍硫化物矿床矿石及其主要围岩铂族元素(PGE)含量,结果表明铂族元素总量(ΣPGE)普遍较低,且ΣPGE由矿床核部的块状矿石(78.15×10-9~555.92×10-9)向外围矿化橄榄岩(6.77×10-9~70.95×10-9)至辉长岩(3.02×10-9)逐步降低。煌斑岩脉岩的ΣPGE也较低,为6.86×10-9~17.03×10-9。ΣPGE与Ni含量呈明显的正相关。不同种类岩石和矿石的PGE原始地幔配分模式明显不同,块状矿石为Pt-Pd配分型,Ir较明显亏损;矿化橄榄岩配分曲线较平坦,IPGE和PPGE分异不明显,但均出现Ru正异常。辉长岩样品和煌斑岩PGE配分模式几乎一致,也均出现明显的Ru正异常。矿石和围岩的Cu/Pd值远高于原始地幔,表明原生岩浆发生了较强的硫化物熔离作用。块状富镍矿石的(Pt+Pd)/(Os+Ir+Ru)和Pd/Ir分别为138.24和24.7,指示其母岩浆为演化较为彻底的玄武质岩浆,而矿化橄榄岩的相应值分别为3.02和16.09,具有科马提质岩浆的特征参数,因此白马寨块状矿石和矿化橄榄岩之间可能没有成因联系。块状硫化物熔体侵位前,其母岩浆经历过长时间强烈的硫化物熔离作用,硫化物熔浆作为独立的侵入相而侵入于III号岩体核部。这个过程反映了峨眉山地幔柱尾部岩浆演化和成矿可能经历过高度的S饱和过程。白马寨矿床形成过程中可能受到地壳物质的混染。  相似文献   

10.
新疆香山铜镍硫化物矿床Re-Os同位素测定   总被引:24,自引:8,他引:24  
通过对香山铜镍硫化物矿石中的镍黄铁矿进行Re-Os同位素测年,获得等时线年龄数据为(298±7.1)Ma。该数据表明产于东天山黄山—镜儿泉一带的这些铜镍硫化物矿床形成于晚石炭世—早二叠世,与该区广泛发育的造山型金矿、矽卡岩型银铜矿床和火山岩型铁铜矿床为同一时期的产物。其等时线~187Os/~188Os初始比值为0.682±0.32,γ_OS平均为444,表明在成矿过程及岩浆侵位期间有地壳物质加入成矿系统中。  相似文献   

11.
Komatiites are mantle-derived ultramafic volcanic rocks. Komatiites have been discovered in several States of India, notably in Karnataka. Studies on the distribution of trace-elements in the komatiites of India are very few. This paper proposes a simple, accurate, precise, rapid, and non-destructive wavelength-dispersive x-ray fluorescence (WDXRF) spectrometric technique for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in komatiites, and discusses the accuracy, precision, limits of detection, x-ray spectral-line interferences, inter-element effects, speed, advantages, and limitations of the technique. The accuracy of the technique is excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Zr, Nb, Ba, Pb, and Th and very good (within 4%) for Y. The precision is also excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th. The limits of detection are: 1 ppm for Sc and V; 2 ppm for Cr, Co, and Ni; 3 ppm for Cu, Zn, Rb, and Sr; 4 ppm for Y and Zr; 6 ppm for Nb; 10 ppm for Ba; 13 ppm for Pb; and 14 ppm for Th. The time taken for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in a batch of 24 samples of komatiites, for a replication of four analyses per sample, by one operator, using a manual WDXRF spectrometer, is only 60 hours.  相似文献   

12.
This paper reports the first results of a study of 11 isotope systems (3He/4He, 40Ar/36Ar, 34S/32S, 65Cu/63Cu, 62Ni/60Ni, 87Sr/86Sr, 143Nd/144Nd, 206–208Pb/204Pb, Hf–Nd, U–Pb, and Re–Os) in the rocks and ores of the Cu–Ni–PGE deposits of the Norilsk ore district. Almost all the results were obtained at the Center of Isotopic Research of the Karpinskii All-Russia Research Institute of Geology. The use of a number of independent genetic isotopic signatures and comprehensive isotopic knowledge provided a methodic basis for the interpretation of approximately 5000 isotopic analyses of various elements. The presence of materials from two sources, crust and mantle, was detected in the composition of the rocks and ores. The contribution of the crustal source is especially significant in the paleofluids (gas–liquid microinclusions) of the ore-forming medium. Crustal solutions were probably a transport medium during ore formation. Air argon is dominant in the ores, which indicates a connection between the paleofluids and the atmosphere. This suggests intense groundwater circulation during the crystallization of ore minerals. The age of the rocks and ores of the Norilsk deposits was determined. The stage of orebody formation is restricted to a narrow age interval of 250 ± 10 Ma. An isotopic criterion was proposed for the ore-bearing potential of mafic intrusions in the Norilsk–Taimyr region. It includes several interrelated isotopic ratios of various elements: He, Ar, S, and others.  相似文献   

13.
最新的流行病学研究表明,空气中较高浓度的悬浮细颗粒可能对人类的健康有不利的影响。根据该项研究显示,由于心脏病、慢性呼吸问题和肺功能指标恶化而导致死亡率的升高与细尘粒子有关。这些研究结果已经促使欧盟于1999年4月出台了限制空气中二氧化硫、二氧化氮、氧化氮、铅和颗粒物含量的法案(1999/30/EC),对各项指标包括对可吸入PM10颗粒的浓度提出了新的限制性指标。PM10颗粒是指可以通过预分级器分离采集的气体动力学直径小于10μm的细颗粒。目前研究的兴趣重点逐步偏向PM2.5这些更细微颗粒物,PM2.5这种颗粒物对健康有明显的不利影响。在欧盟指令2008/50/EC中,对PM10和PM2.5都提  相似文献   

14.
本文介绍样品经四硼酸锂熔融制成玻璃小饼。采用Lachance模式和理论a系数来校正元素间的效应,由3080E型X-射线荧光谱仪和DF-350B数据处理系统完成硅酸盐中十三个项目的测定。  相似文献   

15.
本文拟定了一种以熔融法制备样片,用X射线荧光光谱测定硅酸盐类样品中Si、Fe、Al、Tj、Mn、Ca、Mg、K、Na、P等元素的分析方法。在对不同靶材X光管和分光晶体实验对比的基础上,选择了最佳的测量条件。该法具有快速、准确,测量范围广,检测限低,价格便宜等优点。经过近百个各种类型标样或管理样品的分析对比表明,本法不仅适用于硅酸盐类岩石样品的分析,还适用于铁矿、铝土矿、碳酸盐类岩矿样品以及水泥、耐火材料等样品的分析。  相似文献   

16.
17.
Mining induced subsidence can significantly affect mining costs where major surface facilities and natural environment need to be protected. Overburden grout injection is a technology used to control coal mine subsidence by injecting the mine waste material extracted from the coal back into the inter-burden rock during longwall mining. The flowing slurry is here categorised as a nonlinear viscous cohesive (Bingham plastic) fluid. During longwall mining the grout slurry is pumped into the separated beds of the rock mass through a central vertical borehole, which is drilled deep into the inter-burden rock strata above the coal seam. However, a blockage can occur in the injection system when the slurry velocity falls below a certain critical threshold velocity, indicating a material phase change from cohesive-viscous to cohesive-frictional. In situ field injection tests through boreholes have been simulated at a smaller scale at the CSIRO laboratory in Brisbane by pumping the slurry through a radial disk (gap = 4 mm) from its centre. Laboratory experiments indicate a general, nonlinear, cohesive, viscous, frictional model for shear behaviour of the slurry, in which the material shear parameters are functions of the disk radial distance. Complete dimensional and dimensionless analytical solutions have been developed based on an approach related to Bingham–Herschel–Bulkley fluid mechanics. The derived formulae include relations for minimum pump pressure, local pressure and pressure gradient, wall shear stress, volume rate, velocity and velocity gradient. The theoretical results match the experimental measurements. The experiments covered slurries with maximum particle sizes of 0.5 to 2 mm with about 50% being larger than 100 µm. The viscosities at the various solids concentrations were measured with a standard torsion viscometer. This study differs from the previous research in several distinct aspects, namely, consideration of the variable shear parameters rather than fixed values, inclusion of total nonlinear behaviour, and implementation of a friction function to mimic behaviour of the deposited and consolidating stiff slurry, which can cause a significant pressure rise as a result of the increased shear resistance.  相似文献   

18.
《Applied Geochemistry》2001,16(2):137-159
Five hundred and ninety-eight samples of terrestrial moss (Hylocomium splendens and Pleurozium schreberi) collected from a 188,000 km2 area of the central Barents region (NE Norway, N Finland, NW Russia) were analysed by ICP-AES and ICP-MS. Analytical results for Al, B, Ba, Ca, K, La, Mg, Mn, Na, P, Rb, Si, Sr, Th, U and Y concentrations are reported here. Graphical methods of data analysis, such as geochemical maps, cumulative frequency diagrams, boxplots and scatterplots, are used to interpret the origin of the patterns for these elements. None of the elements reported here are emitted in significant amounts from the smelting industry on the Kola Peninsula. Despite the conventional view that moss chemistry reflects atmospheric element input, the nature of the underlying mineral substrate (regolith or bedrock) is found to have a considerable influence on moss composition for several elements. This influence of the chemistry of the mineral substrate can take place in a variety of ways. (1) It can be completely natural, reflecting the ability of higher plants to take up elements from deep soil horizons and shed them with litterfall onto the surface. (2) It can result from naturally increased soil dust input where vegetation is scarce due to harsh climatic conditions for instance. Alternatively, substrate influence can be enhanced by human activity, such as open-cast mining, creation of ‘technogenic deserts’, or handling, transport and storage of ore and ore products, all of which magnify the natural elemental flux from bedrock to ground vegetation. Seaspray is another natural process affecting moss composition in the area (Mg, Na), and this is most visible in the Norwegian part of the study area. Presence or absence of some plant species, e.g., lichens, seems to influence moss chemistry. This is shown by the low concentrations of B or K in moss on the Finnish and Norwegian side of the (fenced) border with Russia, contrasting with high concentrations on the other side (intensive reindeer husbandry west of the border has selectively depleted the lichen population).  相似文献   

19.
We have developed a set of four synthetic standards for the rare earth and high field strength elements designed for use in the determination of those elements in silicates. The base material is a glass nominally at the eutectic of the MgO-Al2O3-SiO2 ternary system. The nominal doping level was 2 wt% of the elements as oxides. To avoid problems associated with peak interference, the elements were doped in four separate glasses.  相似文献   

20.
Bellechester, Minnesota, is a small community of approximately 155 residents located on the county line between Goodhue and Wabasha counties in southeast Minnesota's karst region. Bellechester is served by a 21-year-old wastewater treatment facility (WWTF) consisting of three waste-stabilization ponds. On 28 April 1992 six sinkholes were discovered to have drained cell 2 of the WWTF resulting in the loss of approximately 8.7×106 1 of partially treated effluent and about 600 m3 of soil into previously undetected subsurface voids of unknown dimensions. In the week following the collapse, approximately 200 water wells located within a 5-km radius of the WWTF were sampled in an after-the-fact, emergency sampling program. Twelve samples with elevated fecal coliform levels, 18 samples with nitrate-nitrogen greater than the 10 mg/1 standard, and no samples with elevated chlorides were found. However, the elevated levels could not be unambiguously attributed to the WWTF collapse. This is the third WWTF to fail by sinkhole collapse in southeast Minnesota since 1974. All three collapsed lagoons have been located in similar geomorphic and stratigraphic settings. However, at least two lagoons have collapsed in the adjacent area in northeast Iowa, and these lagoons are located at different stratigraphic positions. Twenty-two WWTFs constructed in southeast Minnesota's karst region in the last 25 years have been identified as subject to potential sinkhole collapse. An unknown but significant number of manure storage lagoons, flood control structures, etc., have also been constructed in the karst region and are at risk. Public agencies are beginning to develop plans to deal with the risk associated with existing and future waste lagoons in this environment. The critical hydrogeologic parameters that can be used to prioritize the risk of collapse at existing facilities include: (1) the lithology of the first bedrock beneath each lagoon, (2) the thickness of surficial materials between the lagoon and the bedrock surface, (3) the presence and construction of liners (seepage rate), and (4) the proximity to existing sinkholes.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号