首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 15 毫秒
1.
By using the air pluviation technique, it is aimed to achieve the desired relative density with uniform void ratio throughout the specimen in order to maintain the homogeneity and to avoid the spatial variability. Further, in order to achieve the maximum deposition intensity, a systematic optimization study has been carried out rigorously in a test tank to determine the diameter of the orifice to be employed for the sieve plates of different porosity and the number of sieve plates to be installed in the diffuser sieve sets. The study has been conducted with four different patterns of sieves with different porosity to achieve a wide range of relative densities for four different uniformly graded Indian sands. The dynamic penetrometer which is considered to be one of the cost effective instruments has been efficiently used to determine the soil resistance at various locations of the test tank for every given height of fall in order to check the uniformity of placement density throughout the sand bed. The study reveals that the sand beds of different relative densities could be achieved using different patterns of diffuser sieves at optimum sand flow rate without compromising the uniformity. The effect of height of fall as well as porosity of diffuser sieves on the relative density of different sands has been studied in detail. The deposition intensity and the relative density obtained from the present study are compared with the values available in the literature.  相似文献   

2.
An experimental investigation was conducted in order to evaluate the influence of distance from the injection point and of parameters pertinent to the cement, the suspension and the sand on the effectiveness of microfine cement grouts. Three different cement types, each at three different gradations having nominal maximum grain sizes of 100, 20 and 10 μm, were used. Grouting effectiveness was evaluated by injecting suspensions with water to cement (W/C) ratios of 1, 2 and 3, by weight, into five uniform sand fractions with different grain sizes and eight composite sands with different gradations, using a specially constructed apparatus. Unconfined compression and permeability tests were conducted on the resulting grouted sand specimens, after curing for 28 and 90 days. Microfine cement grouted sands obtained unconfined compression strength values of up to 14.9 MPa and permeability coefficients as low as 1.3 × 10?6 cm/s or by up to 5 orders of magnitude lower than those of clean sands. The W/C ratio and the bleed capacity of suspensions as well as the effective grain size and the permeability coefficient of sands are very important parameters, since they affect substantially the grouted sand properties and are correlated satisfactorily with them. The strength and permeability of grouted sands can increase, decrease or remain constant with distance from the injection point depending on the easiness of suspension penetration into the sands. The improvement of grouted sand properties with increasing distance from the injection point is consistent with the observed increase of the cement content of grouted sands.  相似文献   

3.
It is well known that the specimen preparation method and the resulting sand fabric significantly affect sand behaviour and sand liquefaction resistance. In this study, a simple experimental method namely tensiometric method is presented for evaluation of the effect of the samples reconstituting methods on microstructure and the pore-access size distribution of sands. Specimens were prepared using dry funnel pluviation (DFP) and wet deposition (WD) at two densities Dr = 40% (loose state) and Dr = 80% (dense state). The water-retention curve of a sand specimen is evaluated using a technique similar to the hanging column method by application of a step-by-step variation of suction and measure of the corresponding changes in water content. The pore-access size distribution is then evaluated from the water-retention curve. In this experimental study the effects of the mode of deposition and the uniformity coefficient on the pore-access size distribution are investigated. It was found that the specimen generated by the WD method contained a higher percentage of pore size, contrary to the specimen prepared by the DFP which contained a limited percentage of pore size, causing a great influence on the mechanical behaviour of the specimens.  相似文献   

4.
  相似文献   

5.
The effects of initial state of the samples and the overconsolidation ratio (OCR) on the behavior of Chlef sand were studied in this article. For this purpose, the results of two series of undrained monotonic triaxial compression tests on medium dense sand are presented. In the first test series, the influence of the specimen's fabric and confining pressure has been studied. The tests were conducted at initial confining pressure of 50, 100, and 200 kPa. Two methods of sample preparation, which included the dry funnel pluviation and the wet deposition, were utilized. All the samples were subjected to a monotonic loading after consolidation phase. The results of the tests demonstrate that an increase in initial confining pressure leads to an increase in the resistance to liquefaction. The results also show that the samples prepared with the dry funnel pluviation method exhibit a greater resistance to liquefaction than those prepared with the wet deposition method. In the second series of tests, the overconsolidation influence on the resistance to the sand liquefaction has been realized on samples at an effective stress of 100 kPa for OCR varying between 1 and 8. The tests show that the increase of OCR improves the stiffness of sand and accelerates the appearance of dilatancy.  相似文献   

6.
This paper presents the shaking table studies to investigate the factors that influence the liquefaction resistance of sand. A uniaxial shaking table with a perspex model container was used for the model tests, and saturated sand beds were prepared using wet pluviation method. The models were subjected to horizontal base shaking, and the variation of pore water pressure was measured. Three series of tests varying the acceleration and frequency of base shaking and density of the soil were carried out on sand beds simulating free field condition. Liquefaction was visualized in some model tests, which was also established through pore water pressure ratios. Effective stress was calculated at the point of pore water pressure measurement, and the number of cycles required to liquefy the sand bed were estimated and matched with visual observations. It was observed that there was a gradual variation in pore water pressure with change in base acceleration at a given frequency of shaking. The variation in pore water pressure is not significant for the range of frequency used in the tests. The frequency of base shaking at which the sand starts to liquefy when the sand bed is subjected to any specific base acceleration depends on the density of sand, and it was observed that the sand does not liquefy at any other frequency less than this. A substantial improvement in liquefaction resistance of the sand was observed with the increase in soil density, inferring that soil densification is a simple technique that can be applied to increase the liquefaction resistance.  相似文献   

7.
A detailed survey of the upper and middle Nova Scotian continental slope at 42°50′N and 63°30′W indicates a complex morphology dominated by mass movements on various scales and an immature turbidity current channel. The range of sediment facies is diverse including hemipelagic and turbidite muds, turbidite sands and gravelly sandy muds of debris flow origin. Deformed units, interpreted as slump deposits are also observed. Several facies associations, related to discrete morphological environments, are recognized. Thick turbidite sand units with minor intervening mud beds are characteristic of the high-relief uppermost slope and channel margin. Thinner turbidite sands, deformed slump beds and various mud facies are associated with small-scale, hummocky mid-slope topography. Sand beds are more abundant in the depressions than on intervening hummocks indicating the preferred transport paths of small turbidity currents. At the lower end of the main turbidity current channel, frequent turbidite sand beds with relatively minor mud beds are deposited on a depositional lobe. In areas unaffected by mass movements, alternating bioturbated mud and sandy muds make up the core sequences. A local model of sedimentation is proposed for this area and illustrates that simple models of continental slope sedimentation only apply to a limited range of settings.  相似文献   

8.
Three sets of Landsat? satellite images for the years 1993, 1998, and 2003 show that the sand dunes at the southwestern Desert of Egypt are generally moving towards southeast direction with a mean annual creeping speed over ground attaining 15 m/year. The manual-stickled field measurements show that the net annual extension of the longitudinal dunes in the coastal area is between 4 and 5 m/year, while the inland longitudinal dunes showed a net movement ranging between 5 and 6 m/year. Seasonal variations of drift potential and sand movement refer to a strongly high energy wind desert environment in the spring season, high energy wind desert environment in the summer season, and relatively high to intermediate in the autumn and winter seasons, respectively. The total annual estimated volume of transported sand which falls down into Lake Nasser basin attains 16,225,808 m3 as calculated by Bagnold's equation and quantities of sand collected from the sand traps. Comparing this value with the total volume of Lake Nasser Basin, which attains 120?×?109 m3, we can conclude that the sand sheets or sand accumulations may represent serious natural hazards to Lake Nasser in some locations. However, the sand drifting towards the lake may be obstructed by high contour topography hindrance, and the mean grain size of the sand sheets is bigger than 0.25 mm, which needs high wind velocity more than 4 m/s. In addition, the direction of the prevailing wind is N-NNW to S-SSE, and this direction sometimes is parallel to Lake Nasser in some places according to the meandering of the lake. The total lengths of hazardous areas along the western bank of Lake Nasser, which receive the most amounts of the drifted sands, attain 43.6 km only.  相似文献   

9.
The drill and blast method (D&B) is perhaps the most common excavation method for rock mass, and intense blasting vibrations would induce an excavation damage zone (EDZ) around the excavated space. The tensile failure of rock mass in EDZ at diverse rupture velocities results in various geological disasters in engineering practices. The objective of this paper is to investigate the effect of blasting on the tensile strength of sandstone rock and the influence of loading rate on the disk specimens affected by blasting. We firstly performed a D&B exercise on a sandstone block with a size of 600 mm × 600 mm × 120 mm. Then, a total number of 49 standard disk specimens were prepared from large fragments of this blasting sandstone block and an undamaged block. A series of Brazilian split tests was carried out using these specimens to determine their indirect tensile strength, and to assess the effects of the distance from the blasting source and loading rate (varying from 1.67 × 10?5 to 8.33 × 10?2 mm s?1). The results show that the tensile strength of specimens exhibits an upward trend with increasing distance from the blasting source, to approach that of undamaged rock, following a power function with a positive exponent (0~1). The loading rate affects the tensile mechanical behaviors of disks, in terms of the convergence of microscopic defects, the main load-bearing area, and the absorbed energy at the fracture moment of specimens. Both the tensile strength and absorbed energy have positive linear correlations with the natural logarithm of the loading rate. In addition, the fragmentation degree of disk specimens also increases due to an increasing brittleness of sandstone with the loading rate.  相似文献   

10.
The liquefaction vulnerability of fine- to coarse-graded saturated sand and gravelly sand is evaluated by stress control cyclic triaxial laboratory tests. Cyclic triaxial test on reconstituted specimens is carried out with relative density of 45 %. Cyclic triaxial tests performed by sinusoidal wave form with 1-Hz frequency and with the effective consolidation pressure equal to 100 kPa. Cyclic stress ratio which caused initial liquefaction in 15 cycles recognized as the liquefaction resistance in cyclic triaxial test of present study. The result had been used to find a relationship between liquefaction resistance and the grading characteristics (e.g., coefficient of curvature and coefficient of uniformity) of various graded sands and gravelly sands. Then, it is realized that a relationship between liquefaction resistance and any of the sizes (i.e., D 10, D 30, D 50, D 60) appears to be more practical.  相似文献   

11.
The Kaluganga River Estuary is one of the main sources of construction sand in Sri Lanka. Salt water intrusion along this estuary due to extensive sand mining has increased over the years. Thus, the focus of the current research is to understand the relationship between river sand mining, salt water intrusion, and the resultant effects on construction sand. Two surveys were conducted along the Kaluganga Estuary along an 11 km stretch from the river mouth at predetermined intervals to measure depth water quality profiles, and to collect sediment samples. These surveys were carried out during maximum spring tide; first in a dry period and then in a wet period, to understand hydrographic effects on the quality of river sands. Sand samples were analysed for absolute chloride content and grain size distribution. Results showed significant salt water intrusion during the dry period, averaging 2,307 μS cm?1 in surface waters throughout the surveyed 11 km stretch along with 3,818 μS cm?1 (average) in bottom waters up to 5.6 km upstream from the river mouth causing above normal chloride content in the bottom sandy sediments. The high chloride content in bottom sands was recorded up to 5.5 km from the river mouth making them unsuitable for construction purposes. However, during wet period, salt water intrusion levels in the bottom waters were insignificant (average 61 μS cm?1) and the chloride content in bottom sediments was very low. This study highlighted the requirement for regulations on river estuary sandmining for construction purposes.  相似文献   

12.
Effect of Natural Zeolite and Cement Additive on the Strength of Sand   总被引：1，自引：1，他引：0  
It is widely known and well emphasized that the cemented sand is one of economic and environmental topics in soil stabilization. In some instances, a blend of sand, cement and other materials such as fiber, glass, nano particle and zeolite can commercially be available and effectively used in soil stabilization especially in road construction. In regard to zeolite, its influence and effectiveness on the properties of cemented sands systems has not been completely explored. Hence, in this study, based on an experimental program, it has been tried to investigate the potential of a zeolite stabilizer known as additive material to improve the properties of cemented sands. A total number of 216 unconfined compression tests were carried out on cured samples in 7, 28 and 90 days. Results show unconfined compression strength and failure properties improvements of cement sand specimens when cement replaced by zeolite at optimum proportions of 30 % after 28 days due to pozzolanic reaction. The rate of strength improvement is approximately 20–78 and 20–60 % for 28 and 90 days curing times respectively. The efficiency of using zeolite has been enhanced by increasing the cement content and porosity of the compacted mixture. The replacement of cement by natural zeolite led to an increase of the pH after 14 days. Chemical oxygen demand (COD) tests demonstrate that the materials with the zeolite mixture reveal stronger adsorptive capacity of COD in compare to cemented mixture. Scanning electron microscope images show that adding zeolite in cemented sand changes the microstructure (filling large porosity and pozzolanic reaction) that results in increasing strength.  相似文献   

13.
The void distribution of saturated specimens of Ottawa sand is presented. The presence of water inside the sand specimen is detected using the magnetic resonance imaging (MRI) technique. The void distribution of the sample was determined from the image. The specimen was prepared in a non-metallic triaxial cell and was put insie a MRI apparatus to obtain the image. Two sample preparation methods (wet tamping and dry pluviation) were used to illustrate the uniformity of the samples in the initial state. The void distribution along the height of the sample and the three-dimensional orientational void distribution at different locations inside the sample were analysed. The results indicate that the sample generated by the dry-pluviation method is more uniform than the sample generated by the wet-tamping method. When the wet-tamping sample preparation technique is used, the dense sample is more uniform than the loose sample. The development of voids was investigated by a sample loaded inside the MRI device under drained compression condition. The void distribution along the height of the sample at different stages was observed. This work has demonstrated the feasibility of using the MRI technique to examine void distribution in granular material.  相似文献   

14.
The settling behaviour of particulate suspensions and their deposits has been documented using a series of settling tube experiments. Suspensions comprised saline solution and noncohesive glass‐ballotini sand of particle size 35·5 μm < d < 250 μm and volume fractions, φs, up to 0·6 and cohesive kaolinite clay of particle size d < 35·5 μm and volume fractions, φm, up to 0·15. Five texturally distinct deposits were found, associated with different settling regimes: (I) clean, graded sand beds produced by incremental deposition under unhindered or hindered settling conditions; (II) partially graded, clean sand beds with an ungraded base and a graded top, produced by incremental deposition under hindered settling conditions; (III) graded muddy sands produced by compaction with significant particle sorting by elutriation; (IV) ungraded clean sand produced by compaction and (V) ungraded muddy sand produced by compaction. A transition from particle size segregation (regime I) to suppressed size segregation (regime II or III) to virtually no size segregation (IV or V) occurred as sediment concentration was increased. In noncohesive particulate suspensions, segregation was initially suppressed at φs ～ 0·2 and entirely inhibited at φs ≥ 0·6. In noncohesive and cohesive mixtures with low sand concentrations (φs < 0·2), particle segregation was initially suppressed at φm ～ 0·07 and entirely suppressed at φm ≥ 0·13. The experimental results have a number of implications for the depositional dynamics of submarine sediment gravity flows and other particulate flows that carry sand and mud; because the influence of moving flow is ignored in these experiments, the results will only be applicable to flows in which settling processes, in the depositional boundary, dominate over shear‐flow processes, as might be the case for rapidly decelerating currents with high suspended load fallout rates. The ‘abrupt’ change in settling regimes between regime I and V, over a relatively small change in mud concentration (<5% by volume), favours the development of either mud‐poor, graded sandy deposits or mud‐rich, ungraded sandy deposits. This may explain the bimodality in sediment texture (clean ‘turbidite’ or muddy ‘debrite’ sand or sandstone) found in some turbidite systems. Furthermore, it supports the notion that distal ‘linked’ debrites could form because of a relatively small increase in the mud concentration of turbidity currents, perhaps associated with erosion of a muddy sea floor. Ungraded, clean sand deposits were formed by noncohesive suspensions with concentrations 0·2 ≤ φs ≤ 0·4. Hydrodynamic sorting is interpreted as being suppressed in this case by relatively high bed aggradation rates which could also occur in association with sustained, stratified turbidity currents or noncohesive debris flows with relatively high near‐bed sediment concentrations.  相似文献   

15.
砂土层在地面沉降过程中呈现一定的蠕变特性。文章采用一维压缩试验对4 MPa 下砂土的变形特征进行了研究,并 采用改进的试验装置对砂土的微观结构进行了提取。通过对8 组不同级配砂土样的蠕变特性和微观结构分析,得到如下结 论：粒径单一的砂土在蠕变过程中更容易出现突变,砂粒受力后更容易发生破碎,产生滑移错动;砂土蠕变的蠕变量与砂 粒级配密切相关,砂土的粒径越单一且粒径越大时,砂土的蠕变量也越大;采用表征砂土颗粒形状复杂程度的形状系数, 从微观上定量分析了砂土在蠕变过程中发生破碎的情况和蠕变量大小,且形状系数越小,表明该种砂土形状越复杂,在蠕 变过程中砂土的破碎性越高,蠕变量越大。  相似文献   

16.
One-dimensional injection tests were conducted on dry and dense sand columns with a height of 36.5 cm for the injectability evaluation of cement grouts. Three ordinary cement types were pulverized to obtain fine-grained cements having nominal maximum grain sizes of 40, 20 and 10 μm. Suspensions of these cements with water to cement (W/C) ratios of 1, 2 and 3, by weight, were injected into 54 clean, limestone sands with different gradations. Pulverization of the ordinary cements to produce microfine cements extends the range of groutable sands to “medium-to-fine”. Suspension injectability is improved by increasing cement fineness and suspension W/C ratio or by decreasing apparent viscosity and is controlled by the synthesis of the finer portion (d ≤ d25) of the sand gradation. The outcome of the 131 injectability tests conducted is successfully predicted by available groutability criteria at a rate ranging between 51 and 69%. The “new groutability and filtration criteria” proposed in this study, are adapted to the finer 25% of the sand gradation, have successful predictions for 79% of the cases (10–28% higher than those of the existing groutability criteria) and predict successfully the appearance of filtration in 83% of the available cases. The model developed by performing Binary Logistic Regression analyses of the injection test results is considered appropriate for the prediction of injectability of cement grouts in sands because it exhibits a coefficient of multiple determination equal to 0.84 and provides a rate of successful predictions equal to 78% of the available experimental results.  相似文献   

17.
SY地区须家河组二段（下砂）储层类型复杂,各井中均见到砂层,但该砂层储集体有的为高孔隙而有的则致密,在区域平面上表现出分布不均匀的特点。对该段储层预测方法及种类也有较多,但常规叠后反演很难对其进行区分和识别。利用叠前AVO技术,建立储层段的AVO正演模型并采用相应的工作流程,然后利用P-G交汇法对砂岩储层进行解释,发现含气储层与非含气储层的P-G交汇特征不同,砂岩储层含气后则具有交汇趋势线角度增大及远离背境趋势线的特征;而砂岩非储层则相反;其次储层段的P-G交汇点所分布的象限也不相同。通过这些特征,对全区现有钻遇该储层段的钻井进行预测,预测结果和钻井气测情况相吻合,取得了如期效果。  相似文献   

18.
Coring during Integrated Ocean Drilling Program Expeditions 315, 316, and 333 recovered turbiditic sands from the forearc Kumano Basin (Site C0002), a Quaternary slope basin (Site C0018), and uplifted trench wedge (Site C0006) along the Kumano Transect of the Nankai Trough accretionary wedge offshore of southwest Japan. The compositions of the submarine turbiditic sands here are investigated in terms of bulk and heavy mineral modal compositions to identify their provenance and dispersal mechanisms, as they may reflect changes in regional tectonics during the past ca. 1.5 Myrs. The results show a marked change in the detrital signature and heavy mineral composition in the forearc and slope basin facies around 1 Ma. This sudden change is interpreted to reflect a major change in the sand provenance, rather than heavy mineral dissolution and/or diagenetic effects, in response to changing tectonics and sedimentation patterns. In the trench-slope basin, the sands older than 1 Ma were probably eroded from the exposed Cretaceous–Tertiary accretionary complex of the Shimanto Belt and transported via the former course of the Tenryu submarine canyon system, which today enters the Nankai Trough northeast of the study area. In contrast, the high abundance of volcanic lithics and volcanic heavy mineral suites of the sands younger than 1 Ma points to a strong volcanic component of sediment derived from the Izu-Honshu collision zones and probably funnelled to this site through the Suruga Canyon. However, sands in the forearc basin show persistent presence of blue sodic amphiboles across the 1 Ma boundary, indicating continuous flux of sediments from the Kumano/Kinokawa River. This implies that the sands in the older turbidites were transported by transverse flow down the slope. The slope basin facies then switched to reflect longitudinal flow around 1 Ma, when the turbiditic sand tapped a volcanic provenance in the Izu-Honshu collision zone, while the sediments transported transversely became confined in the Kumano Basin. Therefore, the change in the depositional systems around 1 Ma is a manifestation of the decoupling of the sediment routing pattern from transverse to long-distance axial flow in response to forearc high uplift along the megasplay fault.  相似文献   

19.
In the present study, a series of resonant column tests was performed to determine the influence of confining pressure, shear strain and relative density on the dynamic properties and Poisson's ratio of poorly graded clean sand. The tests were performed on the sand specimens of size 50 × 100 mm compacted at relative densities 30, 50 and 75 %. To achieve the corresponding relative density, sand was compacted in 5 equal layers with a specific number of blows. A fixed-free type resonant column apparatus was used to determine the dynamic soil properties at various confining pressures. It has been inferred from the data that the shear modulus (\(G\)) increases with an increase in confining pressure and relative density; and decreases with an increase in shear strain. In addition, damping ratio (\(D\)) decreases with an increase in confining pressure and relative density; and increases with an increase in shear strain. In addition, Poisson’s ratio (\(\nu\)) decreases with an increase in confining pressure and relative density and increases with an increase in the shear strain. The variation of shear modulus with Poisson’s ratio is also discussed. It has been found that there has been a decrease in shear modulus with an increase in Poisson’s ratio of the soil. It is noticed that the small strain shear modulus determined from the present study closely matches with the value determined using the correlations from the literature.  相似文献   

20.
Effects of sediment extraction and dam construction on changes of riverbed characteristics over yearly to decadal scales in the lower Tedori River of Japan are clarified. Over 1950–1991, the riverbed degraded in excess of 0.5–3.5 m. Concurrently, riverbed sediment volume of the 0–16 km reach decreased by 12.7 × 106 m3. Intensive sediment extraction was the dominant cause of riverbed degradation during the period. During 1991–2007, an increase in riverbed sediment volume of 0.6 × 106 m3 resulted in accretion of the riverbed by average depth 0.04 m. The cessation of sand and gravel mining (SGM), coupled with Tedorigawa Dam operation since 1980, was responsible for that accretion. Temporal change in riverbed elevation during 1950–2007 indicates that there were five phases of vertical adjustment. Combination of nonlinear regression models described four of these phases well. During 1950–1979, the first four modes of empirical orthogonal function analysis successfully captured temporal and spatial responses of the riverbed to natural and anthropogenic impacts. That is, the first mode explained the mean riverbed profile and temporal variation in riverbed sediment volume. The second through fourth spatial eigenfunctions reflected spatial variation in vertical adjustment rate for phases II, III and I, respectively. The corresponding temporal eigenfunctions explained the respective effects on the riverbed of SGM, of imbalance between sediment transport capacity and sediment supply, and of dredging activity.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号