首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 125 毫秒
1.
The current study was designed to investigate the extent and severity of contamination as well as the fractionation of potentially toxic elements (As, Cd, Cr, Cu, Pb, Zn, Ni) in minesoils and agricultural soils around a Pb–Zn mine in central Iran. For this purpose, 20 agricultural soils and eight minesoils were geochemically characterized. Results showed that minesoils contained elevated concentrations of As (12.9–254 mg kg−1), Cd (1.2–55.1 mg kg−1), Pb (137–6239 mg kg−1) and Zn (516–48,889 mg kg−1). The agricultural soils were also polluted by As (5.5–57.1 mg kg−1), Cd (0.2–8.5 mg kg−1), Pb (22–3451 mg kg−1) and Zn (94–9907 mg kg−1). The highest recorded concentrations for these elements were in soils influenced directly by tailing ponds. Chromium, Cu and Ni content in agricultural soils (with average value of 74.1, 34.6 and 50.7 mg kg−1, respectively) were slightly higher than the minesoils (with average value of 54.5, 33.1 and 43.4 mg kg−1, respectively). Sequential extraction data indicated that there were some differences between the speciation of PTEs in soil samples. In the agricultural soils, Zn and Cd were mainly associated with carbonate bound fraction, As and Pb with reducible fraction, Cu with oxidisable fraction and Cr and Ni with residual phase. With respect to mobility factor values, Zn and Cd in the agricultural soils have been found to be the most mobile while As mobility is negligible. Also, the mobility factor of As, Cd and Pb in agricultural soils adjoining tailing ponds was high. In minesoil sample Cd was most abundant in the carbonate form, whereas other studied elements were mainly present in the reducible and residual fractions; therefore, despite the high total concentrations of As, Pb and Zn in the minesoils, the environmental risk of these elements was low. Based on the obtained data, a portion of Cu, Cr and Ni input was from agricultural activities.  相似文献   

2.
《Applied Geochemistry》2006,21(8):1335-1346
The chemical speciation of heavy metals (Cd, Cr, Cu, Ni, Pb and Zn) in marine sediments from two coastal regions of Singapore (Kranji in the NW, and Pulau Tekong in the NE) was determined using the latest version of the 3-step sequential extraction procedure, as described by the European Community Bureau of Reference (1999). To obtain a mass balance, a fourth step, i.e., digestion and analysis of the residue was undertaken using a microwave-assisted acid digestion procedure. The total content of all metals except for Pb in sediments was greater in Kranji than in Pulau Tekong. All metals, except Cd were more mobile and bio-available in Kranji, where metals were present at higher percentages in the acid-soluble fractions (the most labile fraction). In sediments from Kranji, the mobility order of the heavy metals studied was Cd > Ni > Zn > Cu > Pb > Cr, whereas sediments from Pulau Tekong showed the same order for Cd, Ni, Pb and Cr, but had a reverse order for Cu and Zn (Cu > Zn). The highest percentages of Cr, Ni and Pb were found in the residual fractions in both Kranji (78.9%, 54.7%, 55.9%, respectively) and Pulau Tekong (82.8%, 77.3%, 62.2%, respectively), meaning that these metals were strongly bound to the sediments. Results are consistent with findings from Barcelona, Spain where similar results for Cr and Ni have also been reported for marine sediments. The sum of the 4 steps (acid-soluble + reducible + oxidizable + residual) was in good agreement with the total content, which implies that the accuracy of the microwave extraction procedure in conjunction with the GFAAS analytical method is assured.  相似文献   

3.
The partitioning of trace metal(oid)s between colloidal and “truly” dissolved fractions in sediment pore waters is often overlooked due to the analytical challenge; indeed, only small volumes are available and filtration membranes are rapidly clogged. Moreover, metal(oid)s are subject to co-precipitate with Fe. In this study, tangential flow filtration (TFF) was assessed for the fractionation of Fe, Mn, Cu, As, Co, Ni, Zn and Cd in sediment pore waters with a 5 kDa cut-off size membrane. Five natural sediments were collected and used for different tests. Results on blank samples showed that this technique was appropriate for Fe, Mn, Co, Zn, As and Cd. Although the applied concentration factors (CF) were low (<7.4) due to the small available volume of pore waters (50 mL), it was shown that colloidal concentrations obtained from the TFF procedure were similar whatever the applied concentration factor. The mass balance approach showed satisfying results (100 ± 25%) for Mn, Co, Zn and As. Mass balances were higher than 130% and highly variable for Cd, Ni and Cu. For Fe, mass balance was reproducible but low (71 ± 10%), probably due to sorption of positively charged Fe oxides on the membrane. Applying this method to five contrasting metal(oid)-contaminated sediments, it was shown that Mn, As, Co and Fe were mainly present in the “truly” dissolved phase (<5 kDa). This technique is a necessary step to assess sediment toxicity and bioavailability of metal(oid)s and could be of great interest for emergent pollutants such as nanometals.  相似文献   

4.
《Applied Geochemistry》2005,20(5):973-987
Due to liming of acid mine drainage, a calcite–gypsum sludge with high concentrations of Zn (24,400 ± 6900 μg g−1), Cu (2840 ± 680 μg g−1) and Cd (59 ± 20 μg g−1) has formed in a flooded tailings impoundment at the Kristineberg mine site. The potential metal release from the sludge during resuspension events and in a long-term perspective was investigated by performing a shake flask test and sequential extraction of the sludge. The sequentially extracted carbonate and oxide fractions together contained ⩾97% of the total amount of Cd, Co, Cu, Ni, Pb and Zn in the sludge. The association of these metals with carbonates and oxides appears to result from sorption and/or coprecipitation reactions at the surfaces of calcite and Fe, Al and Mn oxyhydroxides forming in the impoundment. If stream water is diverted into the flooded impoundment, dissolution of calcite, gypsum and presumably also Al oxyhydroxides can be expected during resuspension events. In the shake flask test (performed at a pH of 7–9), remobilisation of Zn, Cu, Cd and Co from the sludge resulted in dissolved concentrations of these metals that were significantly lower than those predicted to result from dissolution of the carbonate fraction of the sludge. This may suggest that cationic Zn, Cu, Cd and Co remobilised from dissolving calcite, gypsum and Al oxyhydroxides were readsorbed onto Fe oxyhydroxides remaining stable under oxic conditions. In a long-term perspective (≳102 a), ⩾97% of the Cd, Co, Cu, Ni, Pb and Zn content of the sludge potentially is available for release by dissolution of calcite and reductive dissolution of Fe oxyhydroxides if the sludge is subject to a soil environment with lower dissolved Ca concentrations, pH and redox than in the impoundment.  相似文献   

5.
Heavy metals having both natural and anthropogenic origin are common contaminants in soils and sediments, and can be transferred and bioaccumulated at all levels of the food chain, posing serious environmental concern to the local population. In this paper, agricultural soils from the Province of Ferrara (easternmost part of the Padanian Plain, northern Italy) were investigated to assess the levels of potentially toxic metals in relation to their phytoavailability. Agricultural soils have been sampled in order to identify the origin, mobility and bioavailability of heavy metals, collecting superficial and deeper (depths of 20–30 and 100–120 cm, respectively) horizons. The “total” XRF analyses properly elaborated with a statistical approach reveal that soils evolved from two distinct types of alluvial sediments, in turn related to the Po and Reno rivers; the former type is distinctively enriched in heavy metals (particularly Cr and Ni), reflecting the presence of femic and ultrafemic rocks in the hydrological basin of River Po. The absence of Top Enrichment Factors for Ni, Co, Cr, V, and Pb suggests that the content of these elements is natural and unaffected by contamination, whereas superficial enrichments of Cu (and Zn) is ascribed to anthropogenic inputs related to agricultural activities. Multiple extraction tests using variously aggressive reactants (aqua regia, DTPA, EDTA, NH4NO3, and H2O) analyzed by ICP gave insights on the specific mobility of the distinct elements, which decreases in the following order: Pb > Cu > Cd > Co > >Ni > Cr. Taking into consideration the elements that are inducing the main concerns, Cr appears scarcely mobile, whereas Ni could be more phytoavailable and has to be monitored in the local agricultural products. Cd although scarcely abundant has to be monitored for its mobility and toxicity, whereas Cu although abundant and extremely mobile doesn’t induce concerns as it is not hazardous for the living receptors.  相似文献   

6.
At San Roque in Patagonia's Rio Negro Province, Argentina, an In–Au–Cu–Zn–Pb–Ag mineralization (< 0.24 wt.% In, < 7 ppm Au, < 0.45 wt.% Cu, < 14.1 wt.% Zn, < 0.55 wt.% Pb, < 60 ppm Ag) is bound to lava, and volcaniclastics of Triassic through Jurassic age. The polymetallic sulfidic and non-sulfidic indium mineralization is attributed to the low-sulfidation (LS) to intermediate sulfidation (IS) epithermal type of mineralization. Its vein-type and stockwork mineralization developed at 39.2 bars under hydrostatic conditions, corresponding to a depth of 400 m below the water level of the paleoaquifer. In the redox-controlled hypogene mineralization, the temperature increased from 130 °C up to as much as 250 °C at depth, while the pH regime changed from slightly acidic near surface to more alkaline conditions around pH 8 at a depth of approximately 150 m. The monophase mineral associations composed of sphalerite, Ag–Bi-enriched and inclusion-free galena (< 1.7 wt.% Ag, < 3.7 wt.% Bi), chalcopyrite, pyrite, gold, silver, digenite, various In–Cu- and Pb–Zn–Ag “intermediate products”, wittichenite, roquesite, sakuraiite, dzhalindite, brochantite, antlerite, cerussite, and “manganomelane” in a quartz and muscovite-rich gangue have been subdivided into three different stages: (1) Stockwork mineralization of LS to IS epithermal type (hypogene), (2) quartz vein mineralization (hypogene), and (3) salar mineralization (supergene–hypogene).Salt–mud flats controlled the youngest mineralization with Mn, Li, Ca, Mg, V, Sr, Cu, Ag and In bound to oxides, hydroxides, sulfates and subordinate carbonates. The quartz vein mineralization is made up of oxides, hydroxides prevailing over sulfides and containing W, Fe, Au, As, Pb, In, and Cu. It formed at the passage from the vadose into the phreatic zones under oxidizing to slightly reducing conditions. The level marks the boiling level of the hydrothermal solutions involved in the mineralizing process. The hypogene stockwork mineralization is exclusively made up of sulfides containing Zn, Pb, Cu, In, Ag and Bi in the phreatic zones. It developed under reducing conditions. Indium is present at all levels within the volcanic rocks and has been derived from sphalerite rich in Cd (< 1.6 wt.% Cd), In (< 7.3 wt.% In) and Cu (< 7.2 wt.% Cu) while the Fe contents are moderate in sphalerite (< 6.8 wt.% Fe). Indium reached economic grade only through the segregation of a Cu–In–S phase in the “indium window” which is defined by a Cd content of sphalerite in the range 0.2–0.6 wt.% Cd. This concentration of In is controlled by the crystal morphology and the lattice parameters of the minerals involved. It is described as a two-stage process with interdiffusion processes in an Fe-enriched system (stage I) and zoned replacement in an Fe-poor system enriched in indium (stage II). Cu-bearing sphalerite decomposed into sphalerite poor in trace elements and into Cu–In-bearing sphalerite. Further indium concentration took place, when roquesite and sakuraiite decomposed along with an increase in oxygen pressure under hypogene and supergene conditions into dzhalindite. The physical–chemical conditions of the mineralogy and chemical changes in the system In–Cu–Zn–Cd observed in nature have been approximated based upon the results obtained during laboratory studies in material sciences that were focused on solar energy.  相似文献   

7.
《Applied Geochemistry》2007,22(4):821-836
High-resolution sampling (every 3 h) of SPM was performed during a major flood event in a heterogeneous, medium scale watershed of the Garonne-Gironde fluvial-estuarine system (the Lot River; A = 10,700 km2; Q = 151 m3/s). Particulate metal and metalloid (Cd, Zn, Pb, Co, Cr, Ni, Mo, V, U, As, Sb, Th) concentrations were compared with monthly data of the same site (Temple site) obtained during 1999–2002. During the flood event, suspended particulate matter (SPM) concentrations closely followed river discharge with a maximum value (1530 mg/L) coinciding with the discharge peak (2970 m3/s). Trace metal/metalloid concentrations showed significant temporal variations and very contrasted responses. Particulate concentrations were similar to baseline values at the beginning of the flood and mostly increased during the event, showing anticlockwise and complex shape hystereses. Comparison of SPM yield (440,000 t) and particulate metal/metalloid fluxes during the flood with annual fluxes (1999–2002) highlights the great importance of major flood events in fluvial transport. Adequate sampling frequency during floods is necessary for reliable annual flux estimates and provides geochemical signals that may greatly improve our understanding of fluvial transport processes. The scenario of SPM and metal and metalloid transport during the flood are reconstructed by combining variations of Zn, Cd and Sb concentrations, concentration ratios (e.g. Zn/Cd, As/Th, Cd/Th) and hysteresis loops. Changes in SPM and metal/metalloid transport during distinct key stages of the flood were attributed to successive dominance of different water masses transporting material from different sources (e.g. industrial point source, bed sediment from reservoirs, plain erosion). Flood management (dam flushing) clearly enhanced the remobilization of up to 30-a old polluted sediment from reservoir lakes. Sediment remobilization accounted for ∼185,000 t of SPM (i.e. 42% of the total SPM fluxes during the flood) and strongly contributed to particulate metal/metalloid transport for Cd (90%), Zn (83%) and Pb (61%). Therefore, flood management needs to be taken into consideration in future models for erosion and pollutant transport.  相似文献   

8.
Remediation of 56 ML of acidic, contaminant-laden Baal Gammon mine pit water was undertaken using in situ hydrotalcite formation. The pit water composition was modified via the addition of MgCl2·6H2O to form a 2.5:1 M2+:M3+ metal ion ratio followed by the addition of NaOH to increase the pH 10 to induce spontaneous hydrotalcite precipitation. As a result of the in situ hydrotalcite precipitation a broad spectrum of elements of environmental concern including Al, Cd, Co, Cr, Cu, Fe, In, Mn, Mo, Ni, V and Zn were removed from solution. Significantly, an ore grade hydrotalcite precipitate containing Cu (8.0 ± 1.0%) and Zn (3.9 ± 0.5%) was produced directly from the mine pit water column allowing for potential recovery of valuable metals to offset remediation costs. The final water quality produced after in situ remediation was of a simple Na–Cl–SO4 type.  相似文献   

9.
The estimation of potentially harmful element (PHE) availability in urban soil is essential for evaluating impending risks for human and ecosystem health. In the present study five single extraction procedures were evaluated based on the analysis of 45 urban top-soil samples from Athens, Greece. The pseudototal (aqua regia), potentially phytoavailable (0.05 M EDTA), mobilizable (0.43 M HAc), bioaccessible (0.4 M glycine) and reactive pools (0.43 M HNO3) of PHEs were determined. In general, geogenic elements in Athens soil (Ni, Cr, Co, As) are relatively less available than typical tracers of anthropogenic contamination (Pb, Zn, Cu, Cd). Results of principal component analysis (PCA) indicate an association between available fractions of Pb, Cu, Zn, Cd and amorphous Fe oxides, whereas amorphous Mn oxides account for the available concentrations of Mn, Ni and Co. Empirical multiple linear regression models demonstrate that pseudototal concentration is the predominant explanatory factor of variability for the available pools of the anthropogenic elements. Major elemental composition and total organic carbon (TOC) improve the predictions for the geogenic group of elements, although the explained variability remains low. Dilute HNO3 is a better predictor of Zn, Ni, As and Mn availability, whereas Pb and Cu available fractions are predicted more accurately by the classical aqua regia protocol. This study contributes to the international database on the environmental behavior of PHEs and provides additional knowledge that can be used toward the harmonization of chemical extraction methodology in urban soil.  相似文献   

10.
The present work aims to estimate Au-anomalous distribution patterns, the optimum grain size fraction and pathfinder elements for gold placer. The obtained data of analyzed elements (Au, Ag, As, Ba, Cd, Co, Cr, Cu, Fe, Ga, Hg, Li, Mn. Mo, Ni, Pb, Rb, Sb, Se, Sr, Te, Ti, V, Y and Zn) in both the fine (?0.25 mm) and coarse (?1 mm+0.25 mm) grain size fractions of 32 dry stream sediment samples, which have been derived from metamorphosed Island Arc volcanic rocks of Late Proterozoic age, revealed that most of the analyzed elements in both grain size fractions are asymmetrically distributed and did not pass the tests of normality. The coarse grain size fraction appears to be the better size fraction for Au detection and can be considered as the optimum grain size fraction for future application in regional stream sediment surveys. The presence of Au anomalies in the upper part of the stream and beside the mine is either sourced by the main Au-mineralization or new potential extension of the mineralization in the study area. Silver, Cd, Se, Zn and Te can be considered as useful pathfinder elements for Au in the coarse grain size fraction, and they may be used for future geochemical exploration for Au in the area. Recommendation of the authors is pointing to perform lithogeochemical survey in the eastern and western parts of the mine.  相似文献   

11.
《Applied Geochemistry》2006,21(9):1613-1624
Ingestion of soil is a common behaviour in young children as a means of exploring their surroundings. Much attention has been given to remediation of point-source polluted sites with regard to potential health risks for children. However, because of diffuse pollution and long-range atmospheric deposition, soil contaminant levels are generally increased in urban areas compared to their rural counterparts, even in areas located away from any point sources of pollution. Intake of urban soil can thereby result in significant amounts of the child’s daily metal intake. In the present study, soil samples were collected from 25 playgrounds around urban Uppsala, Sweden and analysed for contents of Al, As, Fe, Cr, Cu, Cd, Hg, Mn, Ni, Pb, W and Zn. Prior to aqua regia digestion, the samples were wet-sieved in order to separate soil particle fractions representing deliberate (<4 mm) and involuntary (<50 μm) soil ingestion by children, as well as a third size fraction of 50–100 μm representing soil that is easily transported by suspension. While the metal and As contents in the 50–100 μm fraction were similar to those of the <4 mm fraction, the <50 μm fraction had metal and As contents on average one and a half times higher than those of the <4 mm fraction. The metal and As contents correlated negatively with the sand content in both particle size fractions <4 mm and 50–100 μm, suggesting a general decrease in metal and As content with increasing sand content. However, a positive correlation was found between sand content and the metal and As contents of the finest fraction (<50 μm), suggesting that when the sand content is high, the bulk of the sorbed elements are on the finest particles. The difference between metal and As contents in the different size fractions was greater in the soil sample with the highest sand content than in the sample with the lowest sand content. This implies that texture is a significant factor in metal and As distribution in soils with moderate metal and As contents, when the number of binding sites associated with small particles is low. Tolerable daily intake (TDI) values for Pb and As were exceeded at all sites, and at two sites for Cd, for children with pica behaviour. A high ingestion rate of mainly small particles could also result in the TDI value for Pb being exceeded at 10 sites and that for As at one site. This study also found that soil analysis by the procedure recommended by Swedish authorities accurately represents the metal intake from deliberate soil ingestion, whereas involuntary soil ingestion of mainly small particles could result in metal intakes which are up to twice as high.  相似文献   

12.
The old Senhora das Fontes uranium mine, in central Portugal, consists of quartz veins which penetrated along fracture shear zones at the contact between graphite schist and orthogneiss. The mine was exploited underground until a depth of 90 m and was closed down in 1971. The ores from this mine and two others were treated in the mine area by the heap-leach process which ended in 1982. Seven dumps containing a total of about 33,800 m3 of material and partially covered by natural vegetation were left in the mine area. A remediation process took place from May 2010 to January 2011. The material deposited in dumps was relocated and covered with erosion resisting covers. Surface water and groundwater were collected in the wet season just before the remediation, in the following season at the beginning of the remediation and also after the remediation in the following dry season. Before, at the beginning and after the remediation, surface water and groundwater have an acid-to-alkaline pH, which decreased with the remediation, whereas Eh increased. In general, before the remediation, uranium concentration was up to 83 μg/L in surface water and up to 116 μg/L in groundwater, whereas at the beginning of the remediation it increases up to 183 μg/L and 272 μg/L in the former and the latter, respectively, due to the remobilization of mine dumps and pyrite and chalcopyrite exposures, responsible for the pH decrease. In general, after the remediation, the U concentration decreased significantly in surface water and groundwater at the north part of the mine area, but increased in both, particularly in the latter up to 774 μg/L in the south and southwest parts of this area, attributed to the remobilization of sulphides that caused mobilization of metals and arsenic which migrated to the groundwater flow. Uranium is adsorbed in clay minerals, but also in goethite as indicated by the geochemical modelling. After the remediation, the saturation indices of oxyhydroxides decrease as pH decreases. The remediation also caused decrease in Cd, Co, Cr, Ni, Pb, Zn, Cu, As, Sr and Mn concentrations of surface water and groundwater, particularly in the north part of the mine area, which is supported by the speciation modelling that shows the decrease of most dissolved bivalent species. However, in general, after the remediation, Th, Cd, Al, Li, Pb, Sr and As concentrations increased in groundwater and surface water at south and southwest of the mine area. Before and after the remediation, surface water and groundwater are contaminated in U, Cd, Cr, Al, Mn, Ni, Pb, Cu and As. Remediation caused only some improvement at north of the mine area, because at south and southwest part, after the remediation, the groundwater is more contaminated than before the remediation.  相似文献   

13.
《Applied Geochemistry》2005,20(8):1533-1545
Spring waters were analysed in the field by anodic stripping voltammetry, using equipment which is sufficiently portable to be useful in a remote heavily forested area accessible by foot only. The equipment and techniques are capable of producing analyses on site to the μg/L level for labile metals. Field analysis avoids issues of sample storage and transport protocols that limit confidence in laboratory measurements of labile elements. Samples were taken as a feedback to immediate analysis resulting in a fine grid map of the geological site. Acid rock drainage emanates from a New Zealand historic mine site, with elevated concentrations of metals. However, ground water and surface water discharging naturally from mineralised rocks in the same area also have elevated levels of metals. This study quantifies natural metalliferous discharges from a single site, and compares this to the overall metal flux from the mine area. Acid (pH 3) metalliferous springs emanate from colluvium and bedrock in a young (months-old) landslide. Labile Cu, Pb, Zn and Cd are the environmentally most significant metals in the studied area. Labile metal concentrations observed in the natural springs are up to 24 μg/L Cu, up to 50 μg/L Pb, up to 5 μg/L Cd and up to 9 mg/L Zn. Labile Cu and Zn concentrations are similar to laboratory-determined total concentrations, whereas labile Pb and Cd concentrations are generally distinctly lower than total Pb and Cd concentrations. Four different spring water compositions occur within metres of each other: acid metalliferous water with high Pb, acid metalliferous water with low Pb, high Cu, Pb, Zn acid water and high pH water with elevated Cu. High metal concentrations in these waters are readily attenuated by adsorption to Fe oxyhydroxides (HFO), especially when rain raises spring water pH at the surface. Copper, Pb and Cd are >99% adsorbed, and Zn >95% adsorbed, during this rainfall dilution. Natural spring waters have potential to contribute up to 10% of the total Zn flux from the catchment, but negligible proportions of Cu, Pb and Cd.  相似文献   

14.
This study investigates the concentration and spatial distribution of Cu, Zn, Hg and Pb in the surface (0–2 cm) soils of a regional city in Australia. Surface soils were collected from road sides and analysed for their total Cu, Zn, Hg and Pb concentrations in the <180 μm and <2 mm grain size fractions. The average metal concentration of surface soils, relative to local background soils at 40–50 cm depth, are twice as enriched in Hg, more than three times enriched in Cu and Zn, and nearly six times as enriched in Pb. Median surface soil metal concentration values were Cu – 39 mg/kg (682 mg/kg max), Zn – 120 mg/kg (4950 mg/kg max), Hg – 44 μg/kg (14,900 μg/kg max) and Pb – 46 mg/kg (3490 mg/kg max). Five sites exceeded the Australian NEPC (1999) 300 mg/kg guideline for Pb in residential soils. Strong positive correlations between Cu, Zn and Pb, coupled with the spatial distribution of elevated soil concentrations towards the city centre and main roads suggest traffic and older housing as major sources of contamination. No spatial relationships were identified between elevated metal loadings and locations of past or present industries.  相似文献   

15.
Active and abandoned mine activities constitute the sources of deterioration of water and soil quality in many parts of the world, particularly in the African Copperbelt regions. The accumulation in soils and the release of toxic substances into the aquatic ecosystem can lead to water resources pollution and may place aquatic organisms and human health at risk. In this study, the impact of past mining activity (i.e., abandoned mine) on aquatic ecosystems has been studied using ICP-MS analysis for trace metals and Rare Earth Elements (REE) in sediment samples from Lubumbashi River (RL) and Tshamilemba Canal (CT), Katanga, Democratic Republic of the Congo (DRC). Soil samples from surrounding CT were collected to evaluate trace metal and REE concentrations and their spatial distribution. The extent of trace metal contamination compared to the background area was assessed by Enrichment Factor (EF) and Geoaccumulation Index (Igeo). Additionally, the trace metal concentrations probable effect levels (PELs) for their potential environmental impact was achieved by comparing the trace metal concentrations in the sediment/soil samples with the Sediment Quality Guidelines (SQGs). Spearman's Rank-order correlation was used to identify the source and origin of contaminants. The results highlighted high concentrations of trace metals in surface sediments of CT reaching the values of 40152, 15586, 610, 10322, 60704 and 15152 mg kg−1 for Cu, Co, Zn, Pb, Fe and Mn, respectively. In the RL, the concentrations reached the values of 24093, 2046, 5463, 3340, 68290 and 769 mg kg−1 for Cu, Co, Zn, Pb, Fe and Mn, respectively. The ΣREE varied from 66 to 218 and 142–331 mg kg−1 for CT and RL, respectively. The soil samples are characterized by variable levels of trace metals. The EF analysis showed “extremely severe enrichment” for Cu and Co. However, no enrichment was observed for REE. Except for Mo, Th, U, Eu, Mo, Ho and Tm for which Igeo is classified as “moderately polluted and/or unpolluted”, all elements in different sites are classified in the class 6, “extremely polluted”. The trace metal concentrations in all sampling sites largely exceeded the SQGs and the PELs for the Protection of Aquatic Life recommendation. Cu and Co had positive correlation coefficient values (r = 0.741, P < 0.05, n = 14). This research presents useful tools for the evaluation of water contamination in abandoned and active mining areas.  相似文献   

16.
This study was conducted to assess the anthropogenic impact on metal concentrations in the bottom sediments of the Juam reservoir, Korea, and in stream sediments in its catchment, and to estimate the potential mobility of selected metals (Fe, Mn, Cu, Ni, Pb and Zn) using sequential extraction. A comparison of the metal concentrations in the stream sediments with mean background values in sediments collected from first- or second-order creeks shows that Pb, Cu and Ni are the most affected by anthropogenic inputs. The 206Pb/207Pb ratios of the bottom and core sediments (means: 1.2320 ± 0.0502 and 1.2212 ± 0.0040, respectively) suggest that Pb contamination is mainly due to the waste discharge of abandoned coal and metal mines rather than industrial and airborne sources. Considering the proportion of metals bound to the exchangeable, carbonate and reducible fractions, the comparative mobility of metals is suggested to decrease in the order Mn > Pb > Zn > Ni > Fe ≫ Cu.  相似文献   

17.
《Applied Geochemistry》2005,20(8):1560-1570
Trace-element concentrations in baseline samples from a survey of aquifers used as potable-water supplies in the United States are summarized using methods appropriate for data with multiple detection limits. The resulting statistical distribution models are used to develop summary statistics and estimate probabilities of exceeding water-quality standards.The models are based on data from the major aquifer studies of the USGS National Water Quality Assessment (NAWQA) Program. These data were produced with a nationally-consistent sampling and analytical framework specifically designed to determine the quality of the most important potable groundwater resources during the years 1991–2001.The analytical data for all elements surveyed contain values that were below several detection limits. Such datasets are referred to as multiply-censored data. To address this issue, a robust semi-parametric statistical method called regression on order statistics (ROS) is employed.Utilizing the 90th–95th percentile as an arbitrary range for the upper limits of expected baseline concentrations, the models show that baseline concentrations of dissolved Ba and Zn are below 500 μg/L. For the same percentile range, dissolved As, Cu and Mo concentrations are below 10 μg/L, and dissolved Ag, Be, Cd, Co, Cr, Ni, Pb, Sb and Se are below 1–5 μg/L.These models are also used to determine the probabilities that potable ground waters exceed drinking water standards. For dissolved Ba, Cr, Cu, Pb, Ni, Mo and Se, the likelihood of exceeding the US Environmental Protection Agency standards at the well-head is less than 1–1.5%. A notable exception is As, which has approximately a 7% chance of exceeding the maximum contaminant level (10 μg/L) at the well head.  相似文献   

18.
Trace element geochemistry was studied in geothermal fluids in Iceland. The major and trace element compositions of hot springs, sub-boiling, and two-phase (liquid and vapor) wells from 10 geothermal areas were used to reconstruct the fluid composition in the aquifers at depth. Aquifer fluid temperatures ranged from 4 to 300 °C, pH values between 4.5 and 9.3, and fluids typically contained total dissolved solids <1000 ppm, except in geothermal areas that have seawater and seawater-meteoric water mixtures. Trace alkali elements Li, Rb and Cs are among the most mobile elements in aquifer fluids, with concentrations in the range of <1 ppb to 3.49 ppm Li, <0.01 to 57 ppb Cs, and <1 ppb to 3.77 ppm Rb. Their chemistry is thought to be dominated by rock leaching and partitioning into Na- and K-containing major alteration minerals. Arsenic, Sb, Mo and W are typically present in concentrations in the range of 1–100 ppb. They are relatively mobile, yet Mo may be limited by molybdenite solubility. The alkaline earth elements Ba and Sr are quite immobile with concentrations in the range of <0.1–10 ppb Ba and <1–100 ppb Sr in the dilute fluids, but up to 5.9 ppm Ba and 8.2 ppm Sr in saline fluids. These elements show a systematic relationship with Ca, possibly due to substitution for Ca in Ca-containing major alteration minerals like calcite, epidote and anhydrite. Incorporation into major Ca-minerals may also be important for Mn. Many metals including Fe, Cr, Ni, Zn, Cu, Co, Pb and Ag have low mobility and concentrations, typically <1 ppb for Ag, Cd, Co, Cr, Cu, Ni, and Pb, <10 ppb for Zn and < 100 ppb for Fe, although for some metals higher concentrations are associated with saline fluids. Based on the metals assessed, saturation is approached with respect to many sulfide minerals and in some cases oxide minerals but Cu, Ni and Pb minerals are slightly but systematically undersaturated, and Ag phases significantly undersaturated. Evaluation of mineral-fluid equilibria for these metals is problematic due to their low concentrations, problems associated with assessing the aqueous species distribution by thermodynamic calculations, and uncertainties concerning the exact minerals possibly involved in such reactions. Reaction path calculations, poor comparison of concentrations measured in the samples collected at the wellhead and published downhole data as well as boiling, cooling and mass precipitation calculations suggest removal of many metals due to changes upon depressurization boiling and conductive cooling of the aquifer fluids as they ascend in wells. These results imply that processes such as mass precipitation upon fluid ascent may be highly important and emphasize the importance of considering mass movement in geothermal systems.  相似文献   

19.
《Applied Geochemistry》2006,21(12):2188-2200
Phosphate-induced metal stabilization involving the reactive medium Apatite II™ [Ca10−xNax(PO4)6−x(CO3)x(OH)2], where x < 1, was used in a subsurface permeable reactive barrier (PRB) to treat acid mine drainage in a shallow alluvial groundwater containing elevated concentrations of Zn, Pb, Cd, Cu, SO4 and NO3. The groundwater is treated in situ before it enters the East Fork of Ninemile Creek, a tributary to the Coeur d’Alene River, Idaho. Microbially mediated SO4 reduction and the subsequent precipitation of sphalerite [ZnS] is the primary mechanism occurring for immobilization of Zn and Cd. Precipitation of pyromorphite [Pb10(PO4)6(OH,Cl)2] is the most likely mechanism for immobilization of Pb. Precipitation is occurring directly on the original Apatite II. The emplaced PRB has been operating successfully since January of 2001, and has reduced the concentrations of Cd and Pb to below detection (2 μg L−1), has reduced Zn to near background in this region (about 100 μg L−1), and has reduced SO4 by between 100 and 200 mg L−1 and NO3 to below detection (50 μg L−1). The PRB, filled with 90 tonnes of Apatite II, has removed about 4550 kg of Zn, 91 kg of Pb and 45 kg of Cd, but 90% of the immobilization is occurring in the first 20% of the barrier, wherein the reactive media now contain up to 25 wt% Zn. Field observations indicate that about 30% of the Apatite II material is spent (consumed).  相似文献   

20.
《Applied Geochemistry》1998,13(3):359-368
Studies on the speciation (particulate, colloidal, anionic and cationic forms) of trace metals (Cd, Co, Cu, Fe, Mn, Mo, Ni, Pb, Zn) in the water column and in pore waters of the Gotland Deep following the 1993/94 salt-water inflows showed dramatic changes in the total “dissolved” metal concentrations and in the ratios between different metal species in the freshly re-oxygenated waters below 125 m. Changes in concentrations were greatest for those metals for which the solubility differs with the redox state (Fe, Mn, Co) but were also noted for those metals which form insoluble sulphides (Cd, Pb, Cu, Zn) and/or stable complexes with natural ligands (Cu). Pore water data from segmented surface muds (0–200 mm) indicated that significant redox and related metal speciation changes took place in the surface sediments only a few weeks after the inflow of the oxygenated sea water into the Gotland Deep.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号