共查询到20条相似文献，搜索用时 62 毫秒
1.
Rainfall infiltration and suction variation in unsaturated soils must be taken into consideration in the analysis of most slope stability problems, particularly in the tropical regions where the annual precipitation is high. The process of rainfall infiltration into unsaturated soils is an extremely complex problem attributed to the non-linearity of the hydraulic property functions of the unsaturated soils. This paper describes in detail two instrumented laboratory models, i.e. one-dimensional soil column, and two-dimensional slope model used to provide experimental evidences for the transient suction variations in the unsaturated soils under certain rainfall conditions. The performances of the laboratory models were tested on four typical types of residual soils, i.e. sand-gravel, silty gravel, sandy silt, and silt (kaolin), and a two-layered soil system, i.e. sandy silt underlain by silty gravel. The results showed that the suction distributions for the single-layered homogeneous soils obtained from the simpler one-dimensional soil column were almost identical to that of two-dimensional slope model. However, the two-dimensional slope model should be employed for the two-layered soil system because of the dominant effect of the lateral flow mechanism. The capillary barrier effect was observed when a less permeable soil layer was underlain by a more permeable soil layer. The minimum suction value in soil is governed by the rainfall intensity, rainfall duration, and the saturated permeability of soil. The infiltration rate of the fine-grained soils that subjected to shrink and crack was independent of the soil permeability, but was significantly governed by the preferential flows developed in the soils. 相似文献
2.
不同土壤转换函数预测砂土非饱和导水率的对比分析 总被引：3，自引：0，他引：3
以现有的4种土壤转换函数(Pedotransfer Functions, PTFs)(包括ROSETTA、RAWLS、CAMPBELL和VAUCLIN)为例,将其用于土壤水力性质数据库UNSODA中56个典型砂土样本的非饱和导水率预测,对4种PTFs的预测结果进行了误差分析,探讨了饱和导水率对非饱和导水率预测的影响。结果表明,当同种PTFs预测的饱和导水率作为输入时,在4种PTFs中VAUCLIN的预测精度最高,其次为ROSETTA和RAWLS,CAMPBELL的误差最大;当实测饱和导水率作为输入时,RAWLS、CAMPBELL和ROSETTA的预测精度有了不同程度提高,但VAUCLIN的预测误差反而有所增大;饱和导水率对非饱和导水率预测的影响较大,实测饱和导水率作为输入时CAMPBELL预测的非饱和导水率与实测值最为接近。 相似文献
3.
The French National Agency for Nuclear Waste Management is currently studying the Callovo-Oxfordian claystone as a potential repository for nuclear waste. This study focuses on the hydromechanical (HM) unsaturated response of the rock subjected to hydraulic loading. Static atmosphere drying tests highlighted the HM coupling and mechanical anisotropy of the samples. A coupled poroelastic model was proposed, involving highly nonlinear equations. Numerical simulations were performed using the finite element code Code_Aster. Through a sensitivity analysis, the most suitable parameters for estimation were found to be the Biot coefficient and 3 of the 4 independent parameters of the Van Genuchten?CMualem relations. The parameters were estimated according to an inverse procedure that minimizes a cost functional. The estimates could not outline any hysteretic behavior, but they appeared to be divided into two groups (depending on their fitted values). The convergence and stability of the inverse algorithm were studied, and the results showed that direct computations must be run prior to the inversion to ensure its convergence. No plasticity occurred in the samples (according to the model), whereas irreversible phenomena do take place in situ. 相似文献
4.
蒸发蒸腾作用下非饱和土的吸力和变形影响因素分析 总被引：3，自引：0，他引：3
采用热湿耦合非等温流方程,结合实际蒸发和植物蒸腾的边界条件,考虑了水分迁移所引发的非饱和土应力变形行为,从而建立了大气-非饱和土相互作用模型。采用该模型对控制非饱和土吸力和变形的大气蒸发和植物蒸腾等多参数进行了影响程度分析。结果表明,控制地面吸力和变形的主导因素是外部气象条件,尤其太阳净辐射量和风速,土体水力和热力特性参数影响程度有限;在植被覆盖条件下,吸力变化主要取决于植物叶面积指数LAI,而总腾发量的大小决定了地表变形量。 相似文献
5.
The quality of a numerical modeling solution of moisture flow through unsaturated soil, in part, depends on properly described
unsaturated soil properties. The variability of the Soil Water Characteristic Curve, SWCC, is attributed to hysteresis and
reproducibility of measurement. Because the unsaturated conductivity function is rarely directly measured, the variability
of the unsaturated soil hydraulic conductivity function is attributed to the uncertainty associated with the estimation of
this parameter with currently available fitting functions, and hence a range of reasonable variation was considered. One-dimensional
modeling of expansive soil under dry initial conditions (suction of 1,500 kPa) was performed; both potential evaporation and
infiltration boundary conditions were considered. It was found that small variations in the unsaturated soil hydraulic conductivity
function result in significantly different modeling outputs, as expected, while substential variation in SWCC alone (assuming
the same unsaturated soil hydraulic conductivity for all SWCCs) produced almost identical soil response in terms of soil suction
when the slope of the SWCC is similiar. Thus, proper characterization of the slope of the SWCC is important to proper suction
profile determination. 相似文献
6.
7.
准确计算地下水的垂向入渗补给量是合理评价和利用地下水资源的基础.EARTH模型是一种集中参数的水文模型,可刻画水流在包气带中的运移过程,弥补黑箱模型的不足.以中国科学院栾城农业生态试验站的地下水位观测资料以及气象资料为基础,综合运用降水、蒸发、土壤水、地下水动态观测资料,利用EARTH模型计算了河北平原地下水垂向入渗补给量.计算结果表明,2003年1月1日至2005年8月31日期间,栾城农业生态试验站在降水量1404.1 mm、灌溉量1050.0 mm的条件下地下水入渗补给量为487.2 mm,平均年入渗补给量为182.6 mm, 占降水和灌溉总量(2454.1 mm)的19.9%.在模拟结果的基础上,对不同年份的降水量(含灌溉)和入渗补给量分布的对比分析表明,河北栾城地下水补给滞后现象明显,在研究时间段内峰值滞后18～35 d. 相似文献
8.
9.
单环入渗试验广泛应用于野外测定土壤水力参数。文章在三维非饱和带水分模拟程序VSF基础上,加入了单环入渗水流计算模块,并将改进的VSF与参数优化程序LEVMAR相耦合,构建了适用于单环入渗试验的土壤水力特征参数反演程序VSF-LEVMAR。利用大型室内土槽单环定水头入渗及变水头入渗试验资料,反求水平及垂向饱和入渗系数等土壤水力参数。应用结果表明:该方法既可以利用单环定水头入渗试验单独推求吸湿过程中的土壤水力参数,也可以结合单环定水头入渗与变水头入渗试验同时推求吸湿及脱湿过程中的土壤水力参数。 相似文献
10.
非饱和土的蒸发效应与影响因素分析 总被引：7，自引：4，他引：3
采用非饱和土等温流和考虑热湿耦合的非等温流方程,结合不同的蒸发计算模型,分析了大气蒸发效应对非饱和土吸力变化的影响,并对控制蒸发量计算的多个参数进行了影响程度分析。结果表明,考虑实际蒸发量和非饱和土热湿耦合的水分运动公式能较好地模拟大气影响下非饱和土吸力变化状态,通常所采用的等温流方程加以潜在蒸发量计算非饱和土吸力变化会高估表层蒸发和吸力的下降程度。控制地面蒸发的主导因素是外部气象条件,尤其以太阳净辐射量和风速为最,土体自身特性参数影响程度有限。 相似文献
11.
干湿循环对非饱和膨胀土抗剪强度影响的试验研究 总被引：1，自引：0，他引：1
膨胀土是一种气候敏感性土体,研究在干湿循环过程中膨胀土剪切强度的变化,对了解在自然界周期性蒸发和降雨作用下原位膨胀土体工程性质的变化以及由此导致的地质灾害发生过程具有重要意义。文中以重塑非饱和膨胀土为研究对象,模拟了3次干湿循环过程,对每次干燥路径中的试样进行了直剪试验,重点分析含水率、正压力及干湿循环次数对膨胀土剪切强度的影响,得到如下主要结果：（1）在干燥过程中,随着含水率的减小,试样的刚度、脆性、抗剪强度值（峰值剪切应力）、抗剪强度指标（黏聚力、内摩擦角）及抗剪强度损失（峰值强度与残余强度之差）均呈增加趋势;（2）正压力越高,试样的剪切强度和残余强度越大,而破坏后的峰值强度损失越小,破坏韧性增加;（3）在3次干燥过程中,试样的剪切强度及黏聚力呈先增加后减小的趋势,在第二次干燥过程中达到峰值,但内摩擦角受干湿循环的影响无明显规律;（4）试样经历多次干湿循环后,其剪切特性越来越类似于超固结土,脆性显著增加;（5）干燥过程和干湿循环对试样残余剪切强度的影响都不明显,残余剪切强度基本都在100 kPa附近变化;（6）非饱和膨胀土在干湿循环及干燥过程中剪切强度的变化除了与吸力有关外,还与其微观结构调整和裂隙发育状态密切相关,需要综合非饱和土力学和土质学理论对试验现象进行分析。 相似文献
12.
地下水蒸发是旱区地下水均衡计算中重要的排泄项之一。由于包气带水分运移高度非线性且大气—地表界面动力学过程复杂,估算潜水蒸发量一直是地下水资源评价的难题之一。利用内蒙古乌审旗河南乡均衡试验场E601型蒸渗仪,建立了毛乌素沙地水面蒸发及4种典型岩性（风化砂岩K1、萨拉乌苏组砂Qpal+l、砂质壤土Qhl、风积沙Qheol）的饱和土蒸发原位试验,结合长期观测获取的大量数据,开展了地下水蒸发与水面蒸发、埋深的关系和地下水蒸发量计算方法研究。结果表明:（1）4种典型岩性（风化砂岩、萨拉乌苏组砂、砂质壤土、风积沙）饱和蒸发量与水面蒸发量比值分别为0.60,0.77,0.47,0.88,表明不同岩性的饱和裸土的蒸发强度不等于自由水面的蒸发强度;实际计算裸土蒸发强度时,不能以自由水面蒸发强度作为参考点,如果运用,必须校正。（2）利用蒸渗仪观测数据和土壤水运动方程稳态解析解,获得4种典型岩性（风化砂岩、萨拉乌苏组砂、砂质壤土、风积沙）潜水稳定蒸发计算的关键经验系数c,分别为628932.63,165058.71,48948.21,1525104.031 m?2。（3）利用稳定蒸发公式确定鄂尔多斯盆地风沙滩区四种典型包气带岩性（风化砂岩、萨拉乌苏组砂、砂质壤土、风积沙）潜水极限蒸发深度约为60 cm,结果得到了室内非稳态蒸发试验的佐证,为研究区水资源评价提供了重要的参数依据。 相似文献
13.
14.
15.
掌握岩体的渗透性是精细化描述一个地区水文地质特征的重要工作。渗透系数是表征岩体渗透性的重要指标,研究渗透系数估算模型对于实际工程应用具有重要意义。在现有的渗透系数估算模型中,单因子模型忽略了其他因素对该地区渗透系数的综合影响,复合因子模型存在参数选取不够灵活、部分参数较难获取等问题。基于公开数据,分类整理和对比分析了影响裂隙岩体渗透性的正、负相关参数,提出一种拟合效果好、参数选取灵活的渗透系数估算模型——PNC（Positive and Negative Correlation）模型。研究结果表明:在研究区一,PNC模型的拟合效果（可决系数R2=0.964和R2=0.801）优于HC模型的拟合效果（R2=0.905和R2=0.563）;在研究区二,PNC模型的拟合效果（R2=0.959）优于RMP模型的拟合效果（R2=0.927）;在研究区三,PNC模型的拟合效果（R2=0.94～0.99）优于ZRF模型的拟合效果（R2=0.92～0.99）。利用纳什效率系数（Nash-Sutcliffe Coefficient,NSE）进行模型误差分析,7组数据中有5组数据的误差系数在0.95以上。这说明PNC模型具有便利性和可靠性,可以为实际工程估算和验证渗透系数提供一定的参考。 相似文献
16.
目前大多数非饱和土的弹塑性本构模型用非饱和击实土的试验结果进行验证,但现场其他类型的土,如沉积土经常有在非饱和状态下外部环境变化的情况。现有的非饱和土弹塑性模型是否适用于沉积土一类的现场土是需要研究的课题。进行非饱和上海第③层土的吸力控制排水排气三轴剪切试验,使用文中提出的能统一考虑非饱和土水力性状和力学性状的弹塑性本构模型,预测上述三轴试验结果,并与试验数据进行比较。比较结果显示,建立的本构模型能够很好地预测非饱和上海软土的水力和力学性质,说明该模型不仅可以适用击实土的预测,还能够很好地适用于其他类型非饱和土的水力和力学性质的模拟。 相似文献
17.
In the last decades, a number of hydro-mechanical elastoplastic constitutive models for unsaturated soils have been proposed. Those models couple the hydraulic and mechanical behaviour of unsaturated soils, and take into account the effects of the degree of saturation on the stress–strain behaviour and the effects of deformation on the soil–water characteristic response with a simple reversible part for the hysteresis. In addition, the influence of the suction on the stress–strain behaviour is considered. However, until now, few models predict the stress–strain and soil–water characteristic responses of unsaturated soils in a fully three-dimensional Finite Element code. This paper presents the predictions of an unsaturated soil model in a Three-dimensional Framework, and develops a study on the effect of partial saturation on the stability of shallow foundation resting on unsaturated silty soil. Qualitative predictions of the constitutive model show that incorporating a special formulation for the effective stress into an elastoplastic coupled hydro-mechanical model opens a full range of possibilities in modelling unsaturated soil behaviour. 相似文献
18.
Effect of soil hydraulic properties model on slope stability analysis based on strength reduction method 总被引：2，自引：0，他引：2
Muhammad Mukhlisin Marlin Ramadhan Baidillah Aniza Ibrahim Mohd. Raihan Taha 《Journal of the Geological Society of India》2014,83(5):586-594
Soil hydraulic properties models which have been proposed were derived based on the empirical fitting curve such as Brooks-Corey model (BC) and Van Genuchten model (VG), or based on soil pore radius distribution such as Lognormal model (LN). Each model has different accuracy for predicting soil moisture distribution. In the analysis of rainfall-induced slope failure, the soil hydraulic properties model was needed to describe the physical phenomena of behavior characteristic of water in unsaturated soil. As moisture content has an effect on soil strength, it is vital to select the suitable soil hydraulic properties model for predicting Factor of Safety (FOS) especially in forecasting landslide hazard. In this study, a numerical model of seepage finite element analysis using BC, VG, and LN model were used and compared in order to analyze the soil moisture distribution, water movement phenomenon, and slope stability characteristic in unsaturated soil slope based on the strength reduction method (SRM). The results showed that the variations of the parameters predicting the moisture content of soil leads to differences of FOS in some cases. The parametric study showed that for the unsaturated soil condition, BC model has the greatest FOS value than the other model, while VG model has the lowest. On the other hand, the FOS of all models have the same result for the saturated condition. Other than that, it was found that the increasing of ESP value in the surface layer has significant effect in the sub-surface layer. 相似文献
19.
非饱和残积土的土-水特征曲线试验及模拟 总被引：4，自引：0，他引：4
土-水特征曲线是指基质吸力与含水率或饱和度的关系曲线。土-水特征及其相关数学模型可用于非饱和土性质如渗透系数和抗剪强度模型的建立。通常,土-水特征曲线仅有脱湿曲线。笔者详细讨论了初始含水率、干密度、竖向应力及干湿循环对脱湿曲线的影响。采用滤纸法测试了厦门地区残积土的土-水特征曲线(SWCC)及滞回环。结果表明,初始含水率对SWCC影响较小,最优含水率干侧试样SWCC的进气值小,滞回环小;湿侧试样的进气值大,滞回环大;最优含水率试样的滞回环居中。初始干密度对SWCC有显著影响,低干密度试样SWCC进气值小,脱湿速率快;高干密度试样SWCC进气值高,脱湿速率低。滞回环的大小随着初始干密度的减小而增大。不同竖向应力下SWCC变化较大。随着竖向应力的增加,进气值增大,脱湿速率减小,滞回环减小并趋于稳定。第1次干湿循环对SWCC影响最大,随着循环次数的增加,进气值减小,滞回环减小并趋于稳定。由于残积砂质黏性土SWCC的过渡区和残余区不易区分,残余含水率难以确定,因此,提出5种剔除残余含水率参数的修正SWCC模型,计算分析得出,修正Gardner模型最适合厦门地区残积土的SWCC建模。 相似文献
20.
渗流场水头分布计算是进行渗流量和渗流水力坡降计算的基础,准确、有效地求取渗流场水头分布是渗流计算的关键环节。对均质非饱和土体一维稳态流的流动方程进行分析,考虑到渗透系数是与基质吸力相关的函数,通过数学变换,给出了稳定渗流场的解析通式,并基于渗透性函数中的Gardner模型,给出了非饱和土一维稳态流水头垂直分布的解析解。该解析通式表明,均质非饱和土一维稳态流水头垂直分布主要受地表水头、深度和流动率3个因素控制。分别计算了一维稳态蒸发条件下粉土和黏土两种典型土类水头沿垂直方向的分布。计算结果表明：稳态蒸发条件下粉土层和黏土层内的水头分布表现出相似的变化规律,即自地表至地下水位处随着土层深度的增加,水头分布呈现出加速递减的趋势;在相同的蒸发条件下,对于相同深度处的黏土和粉土而言,黏土层内水头更高些;对同一种土类而言,在较大的蒸发状态下同一深度处土层内水头更高。反之,则较低。 相似文献