共查询到18条相似文献，搜索用时 305 毫秒
1.
裂隙岩体渗流问题一直是水文地质与工程地质的前沿课题之一,等效多孔介质模型是裂隙岩体渗流研究和工程应用的主要方法,此方法的重点在于裂隙岩体渗流模型即典型单元体(REV)的确定。本文采用作者自行开发的离散元软件FractureToKarst,根据国际岩石力学协会对岩石的分类,讨论了非常低延展性裂隙岩体典型单元体(REV)的存在性及大小,并给出确定其存在性的一般方法。通过研究可知,非常低延展性裂隙岩体REV存在的条件就是裂隙平均间距在0.2m以下,即极密间距、很密间距和密间距裂隙岩体存在REV。裂隙平均间距大于0.2 m,即中等间距、宽间距、很宽间距和极宽间距裂隙岩体不存在REV。 相似文献
2.
裂隙岩体渗透系数确定方法研究 总被引：3，自引：0，他引：3
裂隙岩体渗透系数以及渗透主方向的确定对研究岩体渗透性大小及各向异性具有重要意义。高放废物地质处置库介质岩体的渗透性能将直接影响其使用安全性。本文运用离散裂隙网络模拟的方法对我国高放废物处置库甘肃北山预选区3#钻孔附近裂隙岩体进行了渗透性质分析。通过对3#钻孔171.5~178.0m段压水试验数据的反演,标定了离散裂隙网络渗流模型中的裂隙渗透参数(导水系数T)。利用标定的离散裂隙网络模型对场区裂隙岩体进行了渗流模拟,确定了该区域裂隙岩体的渗流表征单元体(REV)的尺寸大小以及渗透主值和主渗透方向。运用离散裂隙网络模型计算得出的渗透主值的几何均值与现场压水试验计算结果较接近,证明了计算结果的有效性。 相似文献
3.
低延展性裂隙岩体REV存在性研究 总被引：1，自引：0，他引：1
采用自行开发的离散元软件FractureToKarst,根据国际岩石力学协会对岩石的分类,讨论了低延展性裂隙岩体典型单元体(REV)的存在性及大小,并给出确定其存在性的一般方法。根据研究结果可知,低延展性裂隙岩体REV存在的条件为裂隙平均间距在0.6 m以下,即极密间距、很密间距、密间距和中等间距裂隙岩体存在REV;裂隙平均间距大于0.6 m,即宽间距、很宽间距和极宽间距裂隙岩体不存在REV。
关键词：裂隙岩体;渗流;典型单元体(REV);离散元 相似文献
4.
工程岩体中数量众多的裂隙面限制了离散裂隙网络模型在岩体渗流中的应用,迫使人们寻找能够用理论上成熟的等效连续介质模型替代,这就要求进行岩体多孔介质的水力等效性研究。在野外大量实测裂隙的基础上,进行裂隙密度、方位、大小、延续性、开度等几何参数的统计分析,以Enhanced Baecher模型建立离散裂隙网络随机模型,采用Monte-Carlo随机模拟方法进行三维裂隙网络随机模拟。在所生成的一定尺度的三维裂隙网络图基础上,给出计算研究域REV的方法,通过判断REV是否存在,确定能否用等效连续介质模型分析岩体渗流。 相似文献
5.
6.
裂隙岩体渗流概念模型研究 总被引：31，自引：4，他引：27
裂隙岩体中的渗流和传统的多孔介质渗流在机理上存在本质的差别,这种差别主要表现为裂隙岩体在各种尺度上存在的非均质性。模拟裂隙岩体渗流的主要困难在于描述这种非均质性。目前的概念模型,包括等效连续体模型、离散裂隙网络模型和混合模型使用了不同的技术来预测裂隙岩体中的渗流。这些模型基于不同的假设和概念框架,有着各自不同的优缺点。在实际应用时,应当根据研究域的具体特点和所要解决的问题的要求对其选择,此外,还讨论了单裂隙的概念模型。 相似文献
7.
8.
岩体裂隙系统渗流场与应力场耦合模型 总被引：15，自引：0，他引：15
仵彦卿 《地质灾害与环境保护》1996,7(1):31-34
岩体系统具有复杂的结构。一般认为，岩体系统是非均质各向异性不连续的多相介质体系。当岩体以裂隙为主，且其分布较密集时，可将岩体系统看作等效连续多相介质体系。本文运用等效连续介质理论，提出了两种岩体裂隙系统渗流场与应力场耦合模型：一是以渗透水压力与隙变形关系、应力与渗透系统数关系为基础，建立渗透系数张量计算公式，进而建立等效效连续介质渗流为数学模型。以裂隙岩体应变张量分析为基础，建立裂隙岩体效应力张量 相似文献
9.
基于三维裂隙网络的裂隙岩体表征单元体研究 总被引：1，自引：0，他引：1
岩体表征单元体（REV）的研究一直是岩土工程中的重要问题。裂隙岩体REV是其内部复杂结构在尺寸效应上的体现,归因于岩体内裂隙系统的随机性。在三维网络模型的基础上通过计算体积节理数建立了确定岩体REV的方法。这种方法考虑了岩体内裂隙的三维空间密度的特征,采用体积节理数这一参数的收敛状况确定岩体REV的大小。建立了实际岩体的模拟裂隙系统,用一定大小的立方体来分割裂隙系统,统计不同立方体内的体积节理数,并将均值作为最终裂隙岩体的参数。将此参数作为裂隙岩体的属性,通过判别其收敛状况获得了岩体REV的尺寸。考虑了岩体不连续面的特征,建立了REV的分析模型,得出工程岩体的REV的尺寸是裂隙平均迹长的4倍的结论。 相似文献
10.
基于离散裂隙网络模型的裂隙水渗流计算 总被引：1，自引：1，他引：0
离散裂隙网络模型(Discrete Fracture Network（DFN）)是研究裂隙水渗流最为有效的手段之一。文章根据裂隙几何参数和水力参数的统计分布,利用Monte Carlo随机模拟技术生成二维裂隙网络,基于图论无向图的邻接矩阵判断裂隙网络的连通,利用递归算法提取出裂隙网络的主干网或优势流路径。基于立方定律和渗流连续性方程,利用数值解析法建立了二维裂隙网络渗流模型,分析不同边界条件下裂隙网络中的流体流动。结果表明,该方法可以模拟区域宏观水力梯度和边界条件下,裂隙网络水力梯度方向总的流量,以及节点的水位、节点间的流量和流动方向的变化特征,为区域岩溶裂隙水渗流计算提供了一种实用、可行的方法。 相似文献
11.
Wang Mingyu The University of Arizona Tucson Arizona USA Department of Water Resources Environmental Engineering China University of Geosciences Beijing Chen Jinsong Wan Li Department of Water Resources Environmental Engineering 《中国地质大学学报(英文版)》2001,12(3)
ＩＮＴＲＯＤＵＣＴＩＯＮＧｒｏｕｎｄｗａｔｅｒｏｒｆｌｕｉｄｆｌｏｗｍｏｄｅｌｉｎｇｉｎｆｒａｃｔｕｒｅｄｒｏｃｋｓｉｓａｃｏｍｐｌｉｃａｔｅｄｔｈｅｏｒｅｔｉｃａｌａｎｄａｐｐｌｉｅｄｔｏｐｉｃ.Ｂｏｔｈｔｈｅｏｒｅｔｉｃａｌｌｙａｎｄｏｐｅｒａｔｉｏｎａｌｌｙ ,ｉｔｉｓｉｍｐｏｒｔａｎｔｉｎｍａｎｙｆｉｅｌｄｓｓｕｃｈａｓｇｅｏｌｏｇｉｃａｌａｎｄｈｙｄｒｏｇｅｏｌｏｇｉｃａｌｅｎｇｉｎｅｅｒｉｎｇ ,ｅｎｖｉｒｏｎｍｅｎｔａｌｅｎｇｉｎｅｅｒｉｎｇａｎｄｐｅｔｒｏｌｅｕｍｅｎｇｉｎｅｅｒｉｎ… 相似文献
12.
裂隙岩体渗透系数确定方法综述 总被引：4，自引：2，他引：4
总结了近年来裂隙岩体渗透系数的确定方法,主要有现场水力试验法、裂隙测量法和离散裂隙网络渗流数值试验法。每种方法都有自己的适用性和测量尺度。裂隙岩体渗透系数存在尺度效应,针对不同尺度的研究对象,应尽量选取与渗流模型网格剖分尺度匹配的测量方法。裂隙的延伸具有方向性,测试点的布设应合理科学,不同测量方法需要结合起来才能得到裂隙岩体真实的渗透系数。 相似文献
13.
Based on a simulation of three-dimensional fracture networks and a superposition principle of liquid dissipation energy for fractured rock masses, a model of the fracture permeability tensor is proposed. An elastic constitutive model of rock fractures, considering fracture closure and dilation during shearing, is also proposed, based on the dilation angle of the fracture. Algorithms of flow-path searching and calculation of the effective flow coefficients for fracture networks are presented, together with a discussion on the influence of geometric parameters of the fractures (trace length, spacing, aperture, orientation and the number of fracture sets) on magnitude, anisotropy of hydraulic permeability and the size of a representative elementary volume (REV). The anisotropy of hydraulic permeability of fractured rock masses is mainly affected by orientation and the number of fracture sets, and the REV size is mainly influenced by trace length, spacing and the number of fracture sets. The results of studies on REV size and the influence of in-situ stress on hydraulic conductivity of the rock mass on the slope of Jinping-I hydropower station, China, are presented using the developed models and methods. The simulation results agreed well with the results obtained from field water-pressure measurements, with an error of less than 10 %. 相似文献
14.
Stress-Dependent Fluid Flow and Permeability in Fractured Media: from Lab Experiments to Engineering Applications 总被引：5，自引：3，他引：5
J. Zhang W. B. Standifird J.-C. Roegiers Y. Zhang 《Rock Mechanics and Rock Engineering》2007,40(1):3-21
Summary. Permeability is a physical property in rocks of extreme importance in energy engineering, civil and environmental engineering,
and various areas of geology. Early on, fractures in fluid flow models were assumed to be rigid. However, experimental research
and field data confirmed that stress-deformation behavior in fractures is a key factor governing their permeability tensor.
Although extensive research was conducted in the past, the three-dimensional stress-permeability relationships, particularly
in the inelastic deformation stage, still remain unclear. In this paper, laboratory experiments conducted on large concrete
blocks with randomly distributed fractures and rock core samples are reported to investigate fluid flow and permeability variations
under uniaxial, biaxial and triaxial complete stress-strain process. Experimental relationships among flowrate, permeability
and fracture aperture in the fractured media are investigated. Results show that the flowrate and stress/aperture exhibit
“cubic law” relationship for the randomly distributed fractures.
A permeability-aperture relationship is proposed according to the experimental results. Based on this relationship, stress-dependent
permeability in a set of fractures is derived in a three-dimensional domain by using a coupled stress and matrix-fracture
interactive model. A double porosity finite element model is extended by incorporating such stress-dependent permeability
effects. The proposed model is applied to examine permeability variations induced by stress redistributions for an inclined
borehole excavated in a naturally fractured formation. The results indicate that permeability around underground openings
depends strongly on stress changes and orientations of the natural fractures. 相似文献
15.
Cubic law with aperture-length correlation: implications for network scale fluid flow 总被引：2，自引：2，他引：0
Christian Klimczak Richard A. Schultz Rishi Parashar Donald M. Reeves 《Hydrogeology Journal》2010,18(4):851-862
Previous studies have computed and modeled fluid flow through fractured rock with the parallel plate approach where the volumetric flow per unit width normal to the direction of flow is proportional to the cubed aperture between the plates, referred to as the traditional cubic law. When combined with the square root relationship of displacement to length scaling of opening-mode fractures, total flow rates through natural opening-mode fractures are found to be proportional to apertures to the fifth power. This new relationship was explored by examining a suite of flow simulations through fracture networks using the discrete fracture network model (DFN). Flow was modeled through fracture networks with the same spatial distribution of fractures for both correlated and uncorrelated fracture length-to-aperture relationships. Results indicate that flow rates are significantly higher for correlated DFNs. Furthermore, the length-to-aperture relations lead to power-law distributions of network hydraulic conductivity which greatly influence equivalent permeability tensor values. These results confirm the importance of the correlated square root relationship of displacement to length scaling for total flow through natural opening-mode fractures and, hence, emphasize the role of these correlations for flow modeling. 相似文献
16.
17.
In this paper, a fully coupled thermo-hydro-mechanical model is presented for two-phase fluid flow and heat transfer in fractured/fracturing porous media using the extended finite element method. In the fractured porous medium, the traction, heat, and mass transfer between the fracture space and the surrounding media are coupled. The wetting and nonwetting fluid phases are water and gas, which are assumed to be immiscible, and no phase-change is considered. The system of coupled equations consists of the linear momentum balance of solid phase, wetting and nonwetting fluid continuities, and thermal energy conservation. The main variables used to solve the system of equations are solid phase displacement, wetting fluid pressure, capillary pressure, and temperature. The fracture is assumed to impose the strong discontinuity in the displacement field and weak discontinuities in the fluid pressure, capillary pressure, and temperature fields. The mode I fracture propagation is employed using a cohesive fracture model. Finally, several numerical examples are solved to illustrate the capability of the proposed computational algorithm. It is shown that the effect of thermal expansion on the effective stress can influence the rate of fracture propagation and the injection pressure in hydraulic fracturing process. Moreover, the effect of thermal loading is investigated properly on fracture opening and fluids flow in unsaturated porous media, and the convective heat transfer within the fracture is captured successfully. It is shown how the proposed computational model is capable of modeling the fully coupled thermal fracture propagation in unsaturated porous media. 相似文献
18.
模拟裂隙多孔介质中变饱和渗流的广义等效连续体方法 总被引：2，自引：0，他引：2
描述了一种计算裂隙多孔介质中变饱和渗流的广义等效连续体方法。这种方法忽略裂隙的毛细作用,设定一个与某孔隙饱和度相对应的综合饱和度极限值,并假定：（1）如果裂隙多孔介质的综合饱和度小于该极限值,水只在孔隙中存在并流动,而裂隙中则没有水的流动;（2）如果综合饱和度等于或大于该极限值,水将进入裂隙,并在裂隙内运动。分析比较了等效连续体模型的不同计算方法,并给出了一个模拟裂隙岩体中变饱和渗流与传热耦合问题的应用算例。结果表明,所述方法具有一般性,可以有效地模拟裂隙多孔介质中变饱和渗流的基本特征。 相似文献