首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 171 毫秒
1.
吕玺琳  张滨  章澎 《工程地质学报》2019,27(5):1110-1115
为分析砂和黏土混合物的强度特性,将石英砂和高岭土按不同质量比配制试验土样,开展了一系列固结排水条件下的环剪试验。通过设置轴压为75 kPa、150 kPa、300 kPa和600 kPa状态下开展试验,得到土样剪切角与剪切应力的关系曲线。根据试验曲线的峰值剪应力,通过莫尔-库仑准则得到土样的黏聚力和摩擦角。结果表明,砂和黏土混合物的黏聚力在5~18 kPa范围内波动,当高岭土含量为50%时黏聚力值达到最小值。当高岭土含量小于50%时,摩擦角随高岭土含量增加略有减小;当高岭土含量超过50%时,摩擦角随高岭土含量增加而减小的趋势更明显。  相似文献   

2.
Use of scrap tyres in isolation systems for seismic damping, requires a knowledge of the engineering properties of sand–rubber mixtures (SRM). The primary objective of this study is to assess the influence of granulated rubber and tyre chips size and the gradation of sand on the strength behaviour of SRM by carrying out large-scale direct shear tests. A large direct shear test has been carried out on SRM considering different granulated rubber and tyre chip sizes and compositions. The following properties were investigated to know the effect of granulated rubber on dry sand; peak shear stress, cohesion, friction angle, secant modulus and volumetric strain. From the experiments, it was determined that the major factors influencing the above-mentioned properties were granulated rubber and tyre chip sizes, percentage of rubber in SRM and the normal stress applied. It was observed that the peak strength was significantly increased with increasing granulated rubber size up to rubber size VI (passing 12.5 mm and retained on 9.5 mm), and by adding granulated rubber up to 30%. This study shows that granulated rubber size VI gives maximum shear strength values at 30% rubber content. It was also found that more uniformly graded sand gives an improved value of shear strength with the inclusion of granulated rubber when compared to poorly graded sand.  相似文献   

3.
为研究剑麻纤维和高分子固化剂复合改良对砂土工程特性影响，通过一系列三轴剪切试验，对不同掺量和长度的剑麻纤维与高分子固化剂改良砂土的剪切强度特性进行了研究，从峰值偏应力、应力应变曲线特征和抗剪强度参数等方面分别对改良机理进行了研究。研究结果表明，纯高分子固化剂改良砂土的峰值偏应力和黏聚力明显提升，由于固化剂粘结砂土颗粒，限制了变形过程中颗粒的相对滑动，内摩擦角略微降低。随纤维掺量的增加，不同围压下固化剂改良土体的峰值偏应力明显增加，应力硬化特征愈加明显，土体的黏聚力和内摩擦角随纤维掺量的增加保持单调递增趋势。在单纯添加固化剂的情况下，土体强度与固化剂浓度呈正相关的关系；在给定0.4%的纤维含量下，随着纤维长度的加长，纤维和高分子固化剂复合改良砂土的剪切强度先增强后降低；在纤维长度为18 mm时，土体的剪切强度达到最大，黏聚力达到最大207.57 kPa；纤维长度的改变对试样破坏时的轴向应变和土体的内摩擦角基本没有影响。  相似文献   

4.
Landfills are one of the major sources of methane (CH4) emission which is a very potent greenhouse gas. The use of a natural process for microbial CH4 oxidation through biocovers provides a source reduction of CH4 emission. Previous studies have mostly focused on biochemical properties, and limited research has been conducted with regards to the geotechnical characterization of compost based biocovers. This paper presents the results of a comprehensive laboratory investigation on pure compost and compost–sand mixtures (with mix ratio of 3:1, 1:1, and 1:3 w/w) to determine the compaction, shear strength, compressibility, and hydraulic and thermal conductivity properties of compost based biocovers. Direct shear and ring shear tests have shown that the cohesion (c) and friction angle (?) are in the range of 2.1–19.7 kPa and 44.1°–54.7°, respectively. Based on the results of one dimensional consolidation tests, the coefficient of consolidation (Cv) values are in the range of 1.71–0.63 m2/year, which is a function of the moisture and organic contents of the samples. The lowest hydraulic conductivity ranges from 6.09 × 10?8 to 1.78 × 10?7 cm/s which occur at optimum moisture contents. Thermal conductivity is measured under various porosities and moisture contents. By increasing the dry density and sand content of the mixtures, thermal conductivity increases. The results presented in this paper will contribute to a better understanding of the geotechnical behaviour of compost based biocover, and thus to a more cost-effective design of biocovers.  相似文献   

5.
The shear strength of cohesionless soil is reduced as the water pressure inside the pores of the soil mass increases. The mathematical relationship between the shear strength and the pore water pressure was derived using Mohr–Coulomb failure criteria as a function of the confining pressure and the effective angle of friction. Experimentally, a series of consolidated drained triaxial tests with back pore water pressure was run on samples of saturated uniform dense sand. The tests were conducted at different confining pressures in the range of 100–400 kPa with an increment of 100 kPa. At each level of confining pressure, the tests were repeated at different values of back pore water pressure in the range of 0–100 kPa with an increment of 25 kPa. For each test, the initial applied back pore water pressure was kept constant during the test for comparing the results at the same effective confining pressure. This study concludes that the mathematical relationship gives accurate results at any level of confining pressure and/or pore water pressure as a function of the effective angle of friction that can be evaluated using single consolidated drained triaxial test at zero back pore water pressure.  相似文献   

6.
Inclusion of synthetic fibers is becoming a routine task in soil reinforcement. The ability of synthetic fibers in controlling the shrinkage cracks in concrete is the main drive to consider its benefits in clay and other soil materials. The polypropylene fibers are nonbiodegradable and can perform well even in aggressive chemical exposure conditions. The direct shear testing is a popular geotechnical approach to assess the shearing strength for a range of soils. This study is aimed at investigating the effect of fiber inclusion on the direct shear response of semi-arid clay soils. This research is conducted using two different types of polypropylene fibers, viz., Fibercast and Fibermesh, having different surface properties on the shear strength envelope and parameters (angle of internal friction and cohesion). The aspect lengths were varied as 6 and 12 mm, and the dosages were varied as 0.2, 0.4, and 0.6 % by weight of the soil. The results were viewed in relation to the fiber type, size, and dose. The soil response and shear resistance measured in consolidated undrained direct shear test is presented for the targeted doses, and the results revealed useful insight compared to unreinforced. The Fibermesh material proved to be the more appropriate fiber additive to typical semi-arid clay soils. The data provides helpful guide for the design geotechnical engineers.  相似文献   

7.
The effects of rate of strain on strength and deformation characteristics of soil–lime were investigated. Five strain rates (0.1, 0.8, 2.0, 4.0 and 7.0 %/min), five lime contents (0, 3, 6, 9 and 12 %) by dry soil weight and three cell pressures (100, 200 and 340 kN/m2) were carried. Triaxial tests, under unconsolidated condition, were used to study the effect of strain rate on strength and initial modulus of elasticity of soil and soil–lime mixture after two curing periods 7 and 21 days, respectively. A total of 405 triaxial specimens have been tested, where 225 specimens have been tested with first curing period (7 days). The testing program includes nine specimens for each strain rate, and each lime content was carried out, including natural soil with zero lime content. Another set of triaxial tests with a total of 180 specimens for the second curing period (21 days) was prepared at optimum moisture content, and the corresponding maximum dry density was also tested. The effects of strain rate and curing period on each of stress–strain behavior, type of failure, deviator stress at failure, cohesion and angle of internal friction and initial modulus of elasticity were studied thoroughly for the natural soil as well as soil–lime mixtures. For natural soil, the test results showed that the undrained shear strength, the initial modulus of elasticity and the cohesion increase significantly as the strain rate increase, while for soil–lime mixture at different curing periods, the undrained shear strength, initial modulus of elasticity and the cohesion increases to a maximum and then decreases as the strain rate and lime content increase. Also, the same variables and angle of internal friction increase with increasing curing period.  相似文献   

8.
为了研究橡胶砂的剪切特性,采用室内大型直剪仪,研究了4种橡胶砂级配（1种间断级配、2种连续级配、1种开级配）、3种橡胶掺入量（10%、30%、60%）、3种竖向应力（30、60、90 kPa）对橡胶砂强度特性和体变特性的影响;并在室内直剪试验的基础上,按照相同级配和橡胶掺量建立纯砂和橡胶砂的离散元数值模型,从颗粒接触状态和颗粒位移角度探讨橡胶砂内在力学机制。研究结果表明：在低橡胶含量下,橡胶砂的剪应力曲线趋势和纯砂一致,但其抗剪强度均低于纯砂;橡胶砂剪切应力随竖向应力的增大而增大,4种级配的橡胶砂中连续级配SR2抗剪强度最高;橡胶颗粒的掺入能有效抑制砂土的剪胀,其中间断级配SR1橡胶砂抑制土体剪胀效果最好,剪胀量相较于纯砂减少了37.6%;橡胶砂的内摩擦角随着橡胶掺入量的增大而减小,同一橡胶掺量下连续级配SR2橡胶砂的内摩擦角最大;橡胶颗粒在橡胶砂力链网络中主要参与弱力链的形成,橡胶砂剪切带宽度小于纯砂的剪切带宽度。  相似文献   

9.
An experimental study was performed to investigate the effect of perlite and perlite–lime admixtures on classification, shear strength, and durability properties of an expansive soil containing smectite clay minerals. Two types of mixtures, namely soil–perlite and soil–perlite–lime, were prepared with different percentages of perlite and compacted with standard Proctor energy at their optimum water contents. Samples of 38 mm diameter and 76 mm height for durability tests and square samples of 60 mm edge for shear box test were taken and preserved until test time in a desiccator. Disturbed samples were also taken to determine liquid and plastic limits. The expansive soil shows behavior of fine sand and silt due to pozzolanic reactions in microstructure caused by addition of lime and perlite. Although apparent cohesion of treated soil decreased with increasing amount of perlite for both types of samples, perlite–lime-treated samples had higher apparent cohesion than only perlite-treated samples. Large increments in angle of shearing resistance were obtained with increasing usage of perlite. Samples stabilized with only perlite could not show enough durability at the durability tests based on volumetric stability and unconfined compression strength. However, samples stabilized with lime and more than 30 % perlite proved to have enough durability and shear strength.  相似文献   

10.
本文以风化砂改良膨胀土的抗剪强度指标为研究对象,通过室内直接剪切试验,研究了在不同垂直荷重作用下,不同掺砂比例及不同含水率对改良膨胀土抗剪强度指标c、值的影响规律及各种不同垂直荷重下的-关系。影响直接剪切试验结果的两个关键因素是试验时的垂直荷重和剪切速率,而现行规范对剪切速率是有明确规定的,但对垂直荷重只有一个推荐性的取值。本文对膨胀土掺入了10%、20%、30%、40%、50%的风化砂,分别配以6%、8%、10%、12%、14%的水,然后在I级垂直荷重(12.5～50kPa)、Ⅱ级垂直荷重(62.5～100kPa)、Ⅲ级垂直荷重(100～400kPa)作用下,进行剪切试验。通过试验研究得知:垂直荷重对改良后膨胀土抗剪强度指标影响较大,随着垂直荷重的减小,掺砂后的膨胀土内摩擦角逐渐增大,黏聚力逐渐减小; 在各级垂直荷重下,在同一含水率状态下,黏聚力均随着掺砂比例的增大而逐渐减小,而内摩擦角均是先增大后减小; 在同一掺砂比例下,黏聚力及内摩擦角均随着含水率的增大而先增大后减小。本试验的研究成果为风化砂改良膨胀土用作公路路基填料提供了试验依据。  相似文献   

11.
The effect of random inclusion of wheat straw (fibers) on shear strength characteristics of Shanghai cohesive soil is presented in this paper. 1 year old natural wheat straw (fibers) with four section lengths of 5, 10, 15, 20 mm (aspect ratio: l/d = 1.67, 3.33, 5, 6.67) are used as reinforcement and specific Shanghai cohesive soil is used as medium. Locally available cohesive soil is compacted with standard Proctor’s maximum density with low percentage of reinforcement (0.1–0.4 % of wheat straw sections by weight of oven-dried soil). A series of direct shear tests were conducted on unreinforced as well as reinforced soil to investigate the shear strength characteristics of wheat straw-reinforced soil. The test results show that the inclusion of randomly distributed wheat straw sections (fibers) in soil increases the shear strength to one degree or another. It is noticed that the optimum wheat straw (fiber) content for achieving maximum shear strength is 0.3 % of the weight of oven-dried soil for wheat straw fiber length 15–20 mm (aspect ratio: 5–6.67).  相似文献   

12.
The hydraulic conductivity represents an important indicator parameter in the generation and redistribution of excess pore pressure of sand–silt mixture soil deposits during earthquakes. This paper aims to determine the relationship between the undrained shear strength (liquefaction resistance) and the saturated hydraulic conductivity of the sand–silt mixtures and how much they are affected by the percentage of low plastic fines (finer than 0.074 mm) and void ratio of the soil. The results of flexible wall permeameter and undrained monotonic triaxial tests carried out on samples reconstituted from Chlef river sand with 0, 10, 20, 30, 40, and 50 % non-plastic silt at an effective confining pressure of 100 kPa and two initial relative densities (D r = 20, 91 %) are presented and discussed. It was found that the undrained shear strength (liquefaction resistance) can be correlated to the fines content, intergranular void ratio and saturated hydraulic conductivity. The results obtained from this study reveal that the saturated hydraulic conductivity (k sat) of the sand mixed with 50 % low plastic fines can be, in average, four orders of magnitude smaller than that of the clean sand. The results show also that the global void ratio could not be used as a pertinent parameter to explain the undrained shear strength and saturated hydraulic conductivity response of the sand–silt mixtures.  相似文献   

13.
安哥拉Quelo砂抗剪强度特性试验研究   总被引：1，自引：0，他引：1  
于永堂  郑建国  刘争宏 《岩土力学》2012,33(Z1):136-140
基于安哥拉Quelo（Muceque）砂原状土和重塑土的直剪试验,探讨了结构性、含水率、干密度对Quelo砂抗剪强度的影响。试验结果表明,结构性对Quelo砂的抗剪强度影响较为复杂,原状土与重塑土的抗剪力学指标具有明显差异;Quelo砂遇水软化特性显著,原状土和重塑土的黏聚力和内摩擦角随含水率的增大近似呈对数衰减;Quelo砂级配良好,压实后抗剪强度高,适宜用作回填材料,重塑土的黏聚力随干密度的增大近似呈线性增大,内摩擦角随干密度的增大分为稳定段和增大段,呈分段函数的特征。  相似文献   

14.
This paper presents the effect of random inclusion of polypropylene fibers on strength characteristics of soil. Locally available cohesive soil (CL) is used as medium and polypropylene fibers with three aspect ratios (l/d = 75, 100 and 125) are used as reinforcement. Soil is compacted with standard Proctor’s maximum density with low percentage of reinforcement (0–1% by weight of oven-dried soil). Direct shear tests, unconfined compression tests and CBR tests were conducted on un-reinforced as well as reinforced soil to investigate the strength characteristics of fiber-reinforced soil. The test results reveal that the inclusion of randomly distributed polypropylene fibers in soil increases peak and residual shear strength, unconfined compressive strength and CBR value of soil. It is noticed that the optimum fiber content for achieving maximum strength is 0.4–0.8% of the weight of oven-dried soil for fiber aspect ratio of 100.  相似文献   

15.
由于室内剪切试验结果存在试样结构性扰动和尺寸效应等带来的不确定性问题,且以往的常规原位大型剪切试验是针对天然状态土体,不能获得饱和土体的强度参数,导致岩土结构稳定性分析和工程设计中大多采用反演方法求取强度参数,而很少直接运用这些试验参数.在本次试验方法研究中,试验仪器仍然采用常规的天然土体原位大型剪切试验仪器,针对土体饱和问题,设计了“制样后饱和法”和“饱和后制样法”2种浸水饱和装置,并采用这2套装置在甘肃省黑方台地区进行了7个饱和黄土原位大型剪切试验.结果表明,2种饱和方法都能够使土样饱和,“饱和后制样法”容易达到饱和,试验历时短,但对试样扰动大,甚至导致试样在制样时破坏,试验成功率低;“制样后饱和法”达到饱和历时稍长,对试样扰动小,试验成功率高.与原位天然大剪试验相比,粘聚力c值由44.65kPa下降至17.35kPa,φ值由14.18°降至11.95°;与室内饱和固结快剪相比,饱和黄土原位大剪的c值增加约4kPa,φ值增加3°左右.  相似文献   

16.
连云港地区软土为碱性环境下沉积的非均质海积软土,软土抗剪强度具有固有各向异性。采用三轴不固结不排水剪切（UU）试验、无侧限抗压强度（UTC）试验、快剪试验和原位十字板剪切（FVT）试验4种方法,对连云港地区软土的不固结不排水抗剪强度特征进行了研究。结果表明：土体水平剪切面强度最低,竖直面抗剪强度最高;土体制样采用垂直方向的切取试样方式时,土体强度最高。根据三轴UU试验得出的黏聚强度和内摩擦角基于土体单元极限平衡理论恢复了土体剪切破坏时的应力状态,计算出土体实际抗剪强度。三轴UU试验得出的抗剪强度平均值约为13.13 kPa,试样破裂面与水平面的夹角在45.1°~45.7°区间最为集中。UTC试验测得的土体平均抗剪强度近似等于三轴UU试验测得的平均抗剪强度。FVT试验测得软土抗剪强度平均值为19.72 kPa,与三轴UU试验和UTC试验得出的抗剪强度平均值相比高了约6.60 kPa,这种现象与室内试验试样的机械扰动、土体应力状态改变和剪切面特征有关。  相似文献   

17.
Use of tire shred–soil mixtures as backfill materials in mechanically stabilized earth walls has several advantages over other backfill materials: (1) good drainage, (2) high shear strength, and (3) low compacted unit weight. This paper presents the results of laboratory pullout tests performed on uniaxial geogrid embedded in tire shred–sand mixtures. The effects of tire shred size, tire shred–sand mixing ratio and confining pressure on the interaction between the geogrid and tire shred–sand mixtures are evaluated. Three sizes of tire shreds are considered: tire chips (with 9.5 mm nominal size), tire shreds 50-to-100 mm long and tire shreds 100-to-200 mm in length, with mixing ratios of 0, 12, 25 and 100 % of tire shreds in the mixtures (by weight). Based on compaction testing of a number of mixtures, the optimal mixing proportion of tire shreds and sand was found to lie between 25/75 and 30/70 (by weight of tire shred and sand); this is equivalent to approximately 40/60 and 50/50, respectively, by volume of tire shreds and sand. The pullout resistance of a geogrid embedded in tire shred–sand mixtures is significantly higher than that of the same geogrid embedded in tire shreds only. The size of the tire shreds has negligible effect on the pullout resistance of a geogrid embedded in mixtures prepared with either low (12/88 mix) or high (100/0 mix) tire shred content. However, when the 25/75 mixture is used, greater geogrid pullout resistance was obtained for the geogrid embedded in tire chip–sand mixtures than in tire shred–sand mixtures.  相似文献   

18.
The characteristics of hydrocarbon-contaminated soils have been among major concerns of geotechnical engineers due to its significant frequency of event and also its influential consequences on our surroundings from various environmental and engineering viewpoints. Heretofore, the effects of diverse kinds of hydrocarbon contaminants on majority of geotechnical properties of fine- and coarse-grained soils such as grain size, hydraulic conductivity, plasticity, compressibility, internal friction, cohesion, and shear strength have been investigated. However, there has not been a concentrated research study examining shear wave velocity (\({\text{V}}_{\text{s}}\)) of hydrocarbon-contaminated soils as an important geotechnical property of soil due to this fact that, in small/very small strain levels, the maximum shear modulus of soils (\({\text{G}}_{ \hbox{max} }\)) can be determined using shear wave velocity (\({\text{G}}_{ \hbox{max} } =\uprho{\text{V}}_{\text{s}}^{2}\)). This paper aims to investigate effects of hydrocarbon contamination on shear wave velocity of sandy soils by comparing shear wave velocities in identically prepared clean and contaminated samples. To this aim, an Iranian light crude oil, a standard type of silica sand (Ottawa sand), and a bender element apparatus were used to minutely measure shear wave velocity of clean and crude oil contaminated sand samples. Moreover, dry and quasi-moist tamping methods were employed in order to provide comparable clean and contaminated specimens (containing 4, 6, 8, 10, and 12 wt% of crude oil), respectively. Firstly, a comprehensive bender element (BE) and resonant column tests were conducted on the identically prepared clean sand samples at various amounts of frequency (2–20 kHz) and under various confining pressure (50–500 kPa) to find the best methods of accurately determining shear wave travel time in BE tests. Thereafter, BE tests were conducted to examine shear wave velocity in contaminated specimens. Based on the results, it was found that there was a critical value for crude oil content with the maximum shear wave velocity so that shear wave velocity of 4 wt% contaminated sand (Vs-4 wt%) was about 1.2 times higher than clean one (Vs-clean), and contrastingly adding further crude oil up to 6 wt% made a significant reduction in value of shear wave velocity to some extent that Vs-6 wt% was slightly lower than Vs-clean (Vs-6 wt% = 0.95–0.97Vs-clean). Moreover, adding more contaminant (8–12 wt%) into sand had negligible influences on shear wave velocity. In this paper, the effects of crude oil contamination on sand microstructure were also evaluated using scanning electron microscopy.  相似文献   

19.
Admixtures and reinforcement materials are frequently used in practice to stabilize coarse and fine grained soils and to improve their engineering properties. However, a limited number of studies have been carried out on fiber-reinforced fine grained soils. In this study, a series of unconfined compression tests, direct shear tests, and California Bearing Ratio tests were carried out to investigate the effect of randomly distributed polypropylene fiber on the strength behavior of a fine grained soil. The content of polypropylene fiber was varied between 0.25 and 1% by total dry weight of the reinforced samples. It was observed that unconfined compression strength, cohesion intercept and California Bearing Ratio increased with the addition of fibers. On the other hand, the results of the tests indicated that shear strength angle was not affected significantly by the fiber reinforcement.  相似文献   

20.
饱和重塑黄土抗剪强度影响因素的试验研究   总被引：1，自引：0，他引：1  
强降雨和灌溉导致黄土强度劣化并发生饱和破坏现象,进而诱发黄土滑坡,给当地带来严重的灾难。饱和黄土抗剪强度的影响因素较多,本文根据水头饱和与反压饱和相结合的原理,利用改装后的TFB-1型非饱和土应力-应变控制式三轴仪对党川地区马兰黄土重塑土样进行饱和试验和CU试验。分别采用50 kPa、100 kPa、200 kPa、400 kPa围压对饱和重塑黄土进行剪切速率分别为0.02 mm·min-1、0.06 mm·min-1、0.2 mm·min-1、0.4 mm·min-1的CU试验,探讨了围压和剪切速率对饱和重塑黄土抗剪强度的影响。研究发现:同一围压下,饱和重塑黄土的抗剪强度随着剪切速率的增大呈先增大后减小的趋势;同一剪切速率下,饱和重塑黄土的抗剪强度随着围压的增大逐渐增大;在干密度相同的条件下,饱和重塑黄土的总黏聚力及有效黏聚力随着剪切速率的增大先减小后增大,总内摩擦角及有效内摩擦角随着剪切速率的增大先增大后减小。该研究可为黄土滑坡预报和范围预测提供一定依据。  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号