共查询到20条相似文献，搜索用时 31 毫秒
1.
A series of centrifuge shaking table model tests are conducted on 4?×?4 pile groups in liquefiable ground in this study, achieving horizontal–vertical bidirectional shaking in centrifuge tests on piles for the first time. The dynamic distribution of forces on piles within the pile groups is analysed, showing the internal piles to be subjected to greater bending moment compared with external piles, the mechanism of which is discussed. The roles of superstructure–pile inertial interaction and soil–pile kinematic interaction in the seismic response of the piles within the pile groups are investigated through cross-correlation analysis between pile bending moment, soil displacement, and structure acceleration time histories and by comparing the test results on pile groups with and without superstructures. Soil–pile kinematic interaction is shown to have a dominant effect on the seismic response of pile groups in liquefiable ground. Comparison of the pile response in two tests with and without vertical input ground motion shows that the vertical ground motion does not significantly influence the pile bending moment in liquefiable ground, as the dynamic vertical total stress increment is mainly carried by the excess pore water pressure. The influence of previous liquefaction history during a sequence of seismic events is also analysed, suggesting that liquefaction history could in certain cases lead to an increase in liquefaction susceptibility of sand and also an increase in dynamic forces on the piles. 相似文献
2.
To a practicing foundation engineer, the performance of batter pile under seismic conditions still remains a questionable prospect. The contradictory findings reported by various investigators with regard to the performance of batter piles add to this dilemma. This calls for a rigorous three-dimensional investigation to evaluate seismic behavior of batter pile groups. In this study, a comparative assessment of three-dimensional seismic behavior of a 2 × 2 vertical and batter pile groups having batter angle of 15° was carried out using a full three-dimensional finite element code developed in MATLAB (Sarkar 2009). The effects of centre to centre spacing of piles and soil modulus values were investigated. Idealized soil profiles having constant and triangular variation of soil modulus were adopted for the study. Results of analyses for both the vertical and batter pile groups are presented in terms of dynamic stiffness and kinematic interaction factors. Results indicate better seismic performance of batter pile groups in comparison to that of vertical pile groups. To demonstrate the importance of the findings, a five-storied portal frame structure supported separately on vertical and batter pile groups were considered and analyzed for El-Centro Earthquake (1940) time history. The difference in structural response considering vertical and batter pile groups is highlighted. 相似文献
3.
Yoon Seok Choi Jintae Lee Monica Prezzi Rodrigo Salgado 《Geotechnical and Geological Engineering》2017,35(4):1587-1604
Although the loads applied on piles are usually a combination of both vertical and lateral loads, very limited experimental research has been done on the response of pile groups subjected to combined loads. Due to pile–soil–pile interaction in pile groups, the response of a pile group may differ substantially from that of a single pile. This difference depends on soil state and pile spacing. This paper presents results of experiments designed to investigate pile interaction effects on the response of pile groups subjected to both axial and lateral loads. The experiments were load tests performed on model pile groups (2 × 2 pile groups) in calibration chamber sand samples. The model piles were driven into the sand samples prepared with different relative densities using a sand pluviator. The combined load tests were performed on the model pile groups subjected to different axial load levels, i.e., 0 (pure lateral loading), 25, 50, and 75% of the ultimate axial load capacity of the pile groups, defined as the load corresponding to a settlement of 10% of the model pile diameter. The combined load test results showed that the bending moment and lateral deflection at the head of the piles increased substantially for tests performed in the presence of axial loads, suggesting that the presence of axial loads on groups of piles driven in sand is detrimental to their lateral capacity. 相似文献
4.
Consoli Nilo Cesar Reginato Naiara da Costa Lopes Júnior Luizmar da Silva Rocha Marcelo Maia Faro Vítor Pereira Born Ricardo Bergan 《Geotechnical and Geological Engineering》2021,39(6):4295-4313
This paper describes the main features related to lateral displacements with depth after successive lateral loading–unloading cycles applied to the top of reinforced-concrete flexible bored piles embedded in naturally bonded residual soil. The bored piles under study have a cylindrical shape, with 0.40-m in diameter and 8.0-m in length. Both bored piles types (P1 and P2) include an embedded steel pipe section in their center as longitudinal steel reinforcements: pile type P1 has another 16 steel rods as steel reinforcement to concrete while pile type P2 has no further steel reinforcement. Pile type P1 has three times as much stiffness (EI) and four and a half times the plastic moment (My) than pile type P2. A similar load–displacement performance was observed at initial loads as for small displacements of both piles. At this initial loading stage, the response of the reinforced concrete piles is a function of the soil characteristics and of a linear elastic pile deformation. During this stage, piles can even be understood as probes for evaluating soil reactions. For larger horizontal displacements, after the concrete section starts undergoing large deformations, approaching the ultimate bending moment, pile behavior and consequently the load–displacement relation starts to diverge for both piles. For pile P1 the values of relevant lateral displacements are extended to about 2.5-m in depth, while for pile P2 lateral displacements are mostly constrained to about 2.0-m in depth. Measurements of horizontal displacements of pile P1 against depth recorded with a slope indicator show that, after unloading, lateral loads at distinct stages (small and near failure loads), exhibits a much higher elastic phase of the system response. An analytical fitting model of soil reaction is proposed based on the measured displacements from slope indicator. The integration of a continuous model proposed for the soil reaction agrees fairly well with the measured displacements up to moments close to plastic limit. Results of load–displacement show that the stiffer pile (P1) was able to mobilize twice as much lateral load compared to pile P2 for a service limit displacement of about 20 mm. The paper shows results that enable the isolation of the structural variable through real scale pile load tests, thus granting understanding of its importance and enabling its quantitative visualization in examples of piles embedded in residual soil sites.
相似文献5.
以苏通长江大桥主墩特大型群桩基础为研究背景,考虑地震动的不确定性,将地震激励作为平稳随机过程,采用随机地震反应分析方法,对深厚场地上群桩基础受上部桥墩荷载下的地震反应进行研究。土体动力非线性性能采用等效线性化方法考虑。由于桥墩惯性作用以及软土土层对桩身位移的约束作用,地震激励下桩身位移呈三角形分布。土体位移与土体和基础间距离有关,桥墩-桩-土相互作用对基础两侧1.5倍基础宽度的土体位移有较大影响。桩体内力反应结果表明,桩顶及桩身上部剪力及弯矩均较大,边桩剪力显著大于中间桩剪力。此外,基于强度破坏准则,对以桩身屈服剪力作为控制指标的群桩基础动力可靠性进行了分析。 相似文献
6.
波浪、船舶等长期水平循环荷载作用下,桩基将不可避免地产生附加应力和变形。针对饱和黏土地层,开展离心模型试验研究了船舶系泊水平荷载作用下单桩和群桩的变形特性。发现水平循环加-卸载诱发了桩周土体的塑性变形,进而导致桩身产生了不可恢复的水平位移和弯曲变形。随着循环荷载的增加,单桩和群桩的桩顶最大水平位移和残余水平位移均同时增加,但残余水平位移明显小于最大水平位移。单桩的桩顶残余水平位移与最大位移比值介于0.17～0.22;群桩的桩顶残余水平位移与最大水平位移比值介于0.30～0.84。水平循环加-卸载作用下,桩身残余弯曲应变明显小于最大弯曲应变。单桩的残余弯曲应变与最大弯曲应变比值介于0.13～0.50;群桩的桩身残余弯曲应变与最大弯曲应变比值介于0.23～0.82。群桩前桩的残余和最大弯曲应变明显大于后桩,前桩与后桩的最大弯曲应变、残余应变比值分别高达3.2和3.1。因此,前桩要采取合理的加固和保护措施,以确保桩基长期服役的安全性。 相似文献
7.
侧向约束技术在地基处理工程中能有效地减小地基沉降。本文结合铁路工程与软土工程特性,采用模型试验与数值模拟的方法,研究了侧向约束(桩)对柔性桩(夯实水泥土桩)复合地基沉降的影响,分析了柔性桩和土体沉降变化随荷载水平的变化规律,探讨了侧向约束条件下土体模量、桩间距等因素对地基沉降的影响。研究结果表明:在柔性桩复合地基中设置侧向约束桩,当土体压缩模量较小时,采用2d(d为桩径)或3d桩距皆能较好地降低桩的沉降量;随着土体压缩模量的增大,桩距采用3d时减沉作用降低、2d时减沉效果增强、4d时减沉作用不明显;桩间土体沉降量在桩距为2d及3d时,减沉作用呈现先减小后增大的特点,4d时其沉降量减小比值为4%~5%。因此,合理设置侧向约束桩才能有效限制软土侧向挤出,以达到减少复合地基沉降的目的。 相似文献
8.
Goit Chandra Shekhar Saitoh Masato Igarashi Takumi Sasaki Shun 《Acta Geotechnica》2021,16(4):1231-1245
Physical-scaled model testing under 1 g conditions is carried out in obtaining the vertical response of fixed head floating-inclined single piles embedded in dry sand. Practical pile inclinations of 5° and 10° besides a vertical pile (0°) subjected to static and dynamic vertical pile head loadings are considered. To account for the effects of soil nonlinearity as well as the soil–pile interface nonlinearity on the response of piles, a range of low-to-high magnitude of pile head displacements is considered for the static case while a varying amplitude of harmonic accelerations for a wide range of frequencies is considered for the dynamic case. Experimental results are obtained in the form of pile head stiffnesses and strains generated in the pile under both the static and dynamic loadings. Results suggest that the nonlinear behavior of soil as well as the nonlinearity generated at the interface between the soil and the pile as the result of applied loading considerably affect the response of piles. The soil–pile interface nonlinearity that governs the slippage of pile shows a clear influence on the pile head stiffnesses by providing two distinct values of stiffnesses corresponding to the push and the pull directional movement of piles; the two values are significantly different. Axial and bending strains generated in the piles show expected dependency on the amplitude of applied loading; the pile head-level bending strain increases almost linearly with the increase in the angle of pile inclination.
相似文献9.
The influence of vertical loads on the lateral response of group piles installed in sandy soil and connected together by a concrete cap is studied through finite elements analyses. The analyses focus on the five piles in the middle row of 3 × 5 pile groups. The vertical load is applied by enforcing a vertical displacement equivalent to 2% of the pile diameter through the pile cap prior to the application of the lateral loads. The results have shown that the lateral resistance of the leading pile (pile 1) does not appear to vary considerably with the vertical load. However, the vertical load leads to 23%, 36%, 64%, and 82% increase in the lateral resistance of piles 2–5, respectively. The increase in the lateral pressures in the sand deposit is the major driving factor to contribute the change in the lateral resistance of piles, depending on the position of the pile in the group. The distribution of lateral loads among piles in the group tends to be more uniform when vertical loads were considered leading to a more economical pile foundation design. 相似文献
10.
轴向荷载对斜桩水平承载特性影响试验及理论研究 总被引：1，自引：0，他引：1
斜群桩受水平荷载作用时,群桩中的基桩受到径向荷载、轴向荷载和弯矩的共同作用。为研究轴向荷载对斜桩水平承载特性的影响,完成了3根单桩以及1组1×2斜桩的大尺寸模型试验。试验结果表明：轴向拉力作用会降低斜桩的水平刚度和极限承载力;而轴向压力作用则会使其水平刚度和极限承载力提高。基于桩侧浅层土体楔形破坏假定,推导了考虑轴向荷载影响的斜桩水平极限土抗力计算公式,提出了桩侧土抗力的p-y曲线方法,并通过模型试验及现场试验验证其合理性。 相似文献
11.
青藏铁路多年冻土区桥梁桩基础地震响应的试验研究与数值分析 总被引：3，自引：0，他引：3
基于对负温条件下青藏铁路高温不稳定多年冻土区桥梁桩基础的缩尺模型振动台试验,明确了动荷载作用下模型桩-土界面和两桩中间土体存在温度升高响应。在此基础上,考虑天然状态和地震荷载作用下地温升高两种条件,运用动力有限元方法,对青藏铁路清水河特大桥桩基础进行了地震响应分析。计算表明,在高温状态下(-1℃以上),多年冻土的地基及桩基础在地震荷载作用下的动态响应对温度的升高异常敏感;在50年超载概率2%的青藏人工波作用下,因桩基础的相对位移增大了地基与桩基础间的滑移、脱离现象,特别是高温状态下地基与桩基础间的变形出现了明显的不稳定滑移,影响了整个桩基础的稳定性。 相似文献
12.
In the present study, the end bearing capacity of screw and straight pipe pile under similar pile tip area and ground conditions were investigated. The effect of increasing overburden pressure was also considered in this research. Pile load tests on close-ended screw and straight pipe piles were conducted in the small scale. Dry Toyoura sand was used to develop the model ground. The sand was compacted at relative density of 70, 80 and 92 %. It was observed that in case of straight pipe pile, load settlement curve plunges downward without increase in load around settlement equals to 10 % of pile tip diameter, whereas in case of screw pile, the load settlement curve plunges around settlement equals to 15 % of pile tip diameter. Moreover, the screw piles having helix-to-shaft diameter ratio 2–4.1 showed 2–12 times higher end bearing capacity than straight pipe piles with similar pile shaft diameter. It was also observed from the test results that the end bearing capacity of single-helix screw pile was in average 16.25 % less than straight pipe pile with similar pile tip area and ground conditions irrespective of the effect of increasing overburden pressure. 相似文献
13.
In 1986, the Malaysian Highway Authority constructed a series of trial embankments on the Muar Plain (soft marine clay) with the aim of evaluating the effectiveness of various ground improvement techniques. This study investigates the effect of two such ground improvement schemes: (a) preloading of foundation with surface geogrids and synthetic vertical drains and (b) sand compaction piles. The paper is focused on the finite element analysis of settlements and lateral displacements of the soft foundation. In scheme (a), the numerical predictions are compared with the field measurements. In scheme (b), only the numerical analysis is presented and discussed in the absence of reliable measurements due to the malfunctioning of the electronic extensometer and inclinometer system during embankment construction. The current analysis employs critical state soil mechanics, and the deformations are predicted on the basis of the fully coupled (Biot) consolidation model. The vertical drain pattern is converted to equivalent drain walls to enable plane strain modelling, and the geogrids are simulated by linear interface slip elements. The effect of sand compaction piles is investigated considering both ideal drains and non-ideal drains, as well as varying the pile stiffness. © 1997 by John Wiley & Sons, Ltd. 相似文献
14.
In an effort to study the seismic pile moment induced by the combined structure–pile inertial and soil–pile kinematic effects for single piles and pile groups in liquefiable ground, an extensive series of 3D finite element simulations are conducted in this paper. The roles that lateral inertial and kinematic interactions play on the pile moment are found to differ in different soil–pile–structure systems. Inertial structure force and kinematic soil displacement of the same direction could cause pile head moments of the same or opposite directions depending on the rotational constraint at the pile head. Kinematic interaction has a dominating influence on the pile moment for pile foundations with pile head rotation constrained by the existence of a pile cap, while inertial interaction is strongly influential for free-head piles. The coupling of inertial and kinematic interactions depends on the soil–pile–structure system configuration and the magnitudes of the inertial structure force and the kinematic soil displacement. Many current pseudo-static methods for calculating the seismic pile moment through summing a percentage of the kinematic induced moment with another percentage of the inertial induced moment could produce very inaccurate results under certain conditions. 相似文献
15.
施工弃土堆填保坎对山区输电线路桩基地震反应会产生何种影响,目前尚不明确。采用FLAC3D数值分析软件建立西南山区典型输电线塔位数值模型,分析桩周有无弃土堆填保坎时桩基础地震动力响应的变化情况,开展定量分析,初步探讨弃土堆填保坎对山区输电线路桩基地震反应的影响。研究表明：桩周弃土堆填保坎后斜坡场地桩基桩身水平峰值加速度、桩身位移、桩身内力、桩周土体位移差的量值均较桩周无弃土堆填保坎时增大。陡坡坡度为35°时,弃土堆填保坎增大了桩基础地震响应,降低了其在陡坡上的抗震性能。 相似文献
16.
Most analytical or semi‐analytical solutions of the problem of load‐settlement response of axially loaded piles are based on the assumption of zero radial displacement. These solutions also are only applicable to piles embedded in either a homogeneous or a Gibson soil deposit. In reality, soil deposits consist of multiple soil layers with different properties, and displacements in the radial direction within the soil deposit are not zero when the pile is loaded axially. In this paper, we present a load‐settlement analysis applicable to a pile with circular cross section installed in multilayered elastic soil that accounts for both vertical and radial soil displacements. The analysis follows from the solution of the differential equations governing the displacements of the pile–soil system obtained using variational principles. The input parameters needed for the analysis are the pile geometry and the elastic constants of the soil and pile. We compare the results from the present analysis with those of an analytical solution that considers only vertical soil displacements. The analysis presented in this paper also provides useful insights into the displacement and strain fields around axially loaded piles. Copyright © 2011 John Wiley & Sons, Ltd. 相似文献
17.
The method of “p–y” curves has been extensively used, in conjunction with simplified numerical methods, for the design and response evaluation of single piles. However, a straightforward application of the method to assess the response of pile groups is questionable when the group effect is disregarded. For this reason, the notion of p-multipliers has been therefore introduced to modify the “p–y” curves and account for pile group effect. The values proposed for p-multipliers result from pile group tests and are limited to the commonly applied spacing of 3.0 D and layout less than 3 × 3, restricting the applicability of the method to specific cases. With the aim of extending the applicability of the “p–y” method to pile groups, the authors have already proposed a methodology for estimating the “p G–y G” curves of soil resistance around a pile in a group for clayey soils. A complementary research allowing for the estimation of the “p G–y G” curves for sandy soils is presented in this paper. The well-known curves of soil resistance around the single pile in sandy soils are appropriately transformed to allow for the interaction effect between the piles in a group. Comparative examples validate the applicability and the effectiveness of the proposed method. In addition, the method can be straightforwardly extended to account for varying soil resistance, according to the particular location of a pile in a group. It can therefore be used in a most accurate manner in estimating the distribution of forces and bending moments along the characteristic piles of a group and therefore to design a pile foundation more accurately. 相似文献
18.
The load distributions of the grouped piles under lateral loads acting from one side of the pile cap could be approximately modeled using the elasticity equations with the assumptions that the underground structure is rigid enough to sustain the loads, and only small deformations of the soils are yielded. Variations of the soil–pile interactions along the depths are therefore negligible for simplicity. This paper presents the analytical modeling using the dynamic pile‐to‐pile interaction factors for 2 × 2 and 2 × 3 grouped piles. The results were found comparative with the experimental and numerical results of other studies. Similar to others' findings, it was shown that the leading pile could carry more static loads than the trailing pile does. For the piles in the perpendicular direction with the static load, the loads would distribute symmetrically with the centerline whereas the middle pile always sustains the smallest load. For steady‐state loads with operating frequencies up to 30 Hz, the pile load distributions would vary significantly with the frequencies. It is interesting to know that designing the pile foundation needs to be cautioned for steady‐state vibrations as they are a problem of machine foundation. However, for transient loads or any harmonic loads acting upon relatively higher frequencies, the pile loads could be regarded as uniformly distributed. It is hoped that the numerical results of this paper will be helpful in the design practice of pile foundation. Copyright © 2008 John Wiley & Sons, Ltd. 相似文献
19.
Youlin Guo Minghua Zhao Guihai Fu Yongsuo Li Pengfei Yu 《Geotechnical and Geological Engineering》2017,35(4):1439-1451
In order to solve the bulging deformation and fracture at the top of widely used gravel piles in treating ground consolidation, a new, optimized composite foundation form was proposed. The composite foundation was constructed using discrete materials and concrete piles. Additionally, various parameters of this new composite foundation were analyzed, including foundation forms, construction technologies, bearing mechanism and failure mode. By applying cavity expansion theory, the Vesic cavity spreading pressure of the discrete material-concrete pile is solved as a polar axis symmetric problem on the basis of Mohr–Coulomb yield criterion. Then the computing formula for the ultimate bearing capacity of the discrete materials-concrete pile is elicited when the internal friction angle of soil in the piles is φ = 0 and φ ≠ 0. Finally, the ultimate bearing capacity value of the composite foundation is acquired through analytic calculation and numerical simulation. Finally, it is found that the calculation result is 14.4% lower than that of the simulated result, which is within the acceptable accuracy range and therefore proves the accuracy of the analytic calculation method for bearing capacity of the new composite foundation. 相似文献
20.
在深入分析密集型静力压入式预制桩挤土效应和群桩效应的机理和不利影响的基础上，建立了确保地基土不因挤土效应而破坏的孔隙水压力监控模型，优化压桩线路和次序的超静孔压监控模型，确保基桩不因桩周土隆起而被拔断的基桩轴力监控模型，确保基桩不因挤土效应而产生弯折破坏以及桩间土不因群桩效应而产生剪切破坏的桩侧土压力监控模型。实测数据表明，在没有采取有效的降排水和卸压预防措施时，沉桩施工容易导致地基土强度失效和基桩拔断破坏。采取袋装砂井排水和碎石桩式降水井降水后。即使是透水性差的软土地基。也可使较大的超静孔压在1d时间内消散70％。 相似文献