首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 171 毫秒
1.
颗粒级配和结构对粉砂力学性质的影响   总被引:5,自引:2,他引:3  
王淑云  鲁晓兵  时忠民 《岩土力学》2005,26(7):1029-1032
分析了几组原状、重塑和配制土样的静三轴试验结果,认为颗粒级配和结构性是影响粉砂应力-应变关系和强度特性的两个主要因素。当颗粒级配不同时,结构性原状粉砂土样和不具有结构性的配制土的强度均不同。相同颗粒级配的原状和重塑粉砂的强度也不同。而颗粒级配稍有不同的一种配制粉砂与原状粉砂在应力-应变关系和强度特性方面相接近。此种配制粉砂可替代原状粉砂做为模型试验用土。  相似文献   

2.
饱和层状砂土液化特性的动三轴试验研究   总被引:2,自引:0,他引:2  
利用GDS动三轴试验系统采用等幅循环应变加载方式对含有不同厚度粉土的饱和层状砂土进行了液化强度试验。分析了均匀砂和含有不同粉粒层厚度的层状砂土在循环荷载作用下的变形和力学特性。试验分析表明:由于含粉粒夹层的层状土特殊的土体结构,其孔隙水压力发展规律与一般的无黏性砂土不同;饱和层状砂土的抗液化强度并不是随着粉粒层厚度的增加而单调增加的,而是存在一个临界点;液化临界剪应变的大小与液化判别标准和循环次数有很大关系。试验结果表明,粉粒夹层对层状砂土的液化特性有很大的影响,且更能模拟自然环境条件下的层状砂土地基液化特性。  相似文献   

3.
Loose saturated cohesionless soils are most susceptible to liquefaction, however there are strong historical evidence suggesting that soils containing fines such as silty sands are also prone to liquefaction during earthquakes. The liquefaction of silty sands has been observed in a number of recent case studies. This paper presents the effects of fine silts on liquefaction potential of sandy soil. Tests have been conducted on the vibration table at different accelerations and pore water pressure is measured. During the lab investigation, locally (Roorkee, India) available Solani Sand and Dhanauri Silt have been used. The soil samples have been prepared by varying silt content and the initial relative density. The results of the study performed are used to clarify the effects of non-plastic fines content on the Solani sand. As the silt content increases, the number of cycles required to produce maximum pore water pressure increases. For a particular level of excitation, rate of pore water pressure generation is maximum at critical silt content. It is observed that critical silt content to generate maximum pore water pressure is different for different accelerations. Further, effect of silt content is very much dependent on relative density.  相似文献   

4.
In a number of recent case studies, the liquefaction of silty sands has been reported. To investigate the undrained shear and deformation behaviour of Chlef sand–silt mixtures, a series of monotonic and stress-controlled cyclic triaxial tests were conducted on sand encountered at the site. The aim of this laboratory investigation is to study the influence of silt contents, expressed by means of the equivalent void ratio on undrained residual shear strength of loose, medium dense and dense sand–silt mixtures under monotonic loading and liquefaction potential under cyclic loading. After an earthquake event, the prediction of the post-liquefaction strength is becoming a challenging task in order to ensure the stability of different types of earth structures. Thus, the choice of the appropriate undrained residual shear strength of silty sandy soils that are prone to liquefaction to be used in engineering practice design should be established. To achieve this, a series of undrained triaxial tests were conducted on reconstituted saturated silty sand samples with different fines contents ranging from 0 to 40 %. In all tests, the confining pressure was held constant at 100 kPa. From the experimental results obtained, it is clear that the global void ratio cannot be used as a state parameter and may not characterize the actual behaviour of the soil as well. The equivalent void ratio expressing the fine particles participation in soil strength is then introduced. A linear relationship between the undrained shear residual shear strength and the equivalent void ratio has been obtained for the studied range of the fines contents. Cyclic test results confirm that the increase in the equivalent void ratio and the fines content accelerates the liquefaction phenomenon for the studied stress ratio and the liquefaction resistance decreases with the increase in either the equivalent void ratio or the loading amplitude level. These cyclic tests results confirm the obtained monotonic tests results.  相似文献   

5.
During the last mid-century, the Chlef area was strongly affected by two earthquakes. From the geological context, there were numerous ejections onto the ground level of great masses of sandy soils and large displacements of various forms of some building foundations. These damages are due to soil liquefaction problem. This loss of shear strength can be attributed to many factors. History of recent cases indicates that sand deposited with silt content is much more liquefiable than clean sand. Therefore, a deep understanding of silty sand behavior is needed for the liquefaction assessment of silty sandy soils. Moreover, during seismic shaking, the post-liquefaction behavior of silty sand and, consequently, the stability of structures founded on liquefied soil depend on the steady-state shear strength of soil. The objective of this laboratory investigation is to show the effect of silt contents and the relative density on the mechanical behavior of such soils in monotonic loading. In this context, a series of undrained triaxial tests were performed on reconstituted saturated silty sand samples with different fines content ranging from 0% to 40%. In all tests, the confining pressure was held constant to 100 kPa. The fines content and the global void ratio are expressed by means of the equivalent void ratio. Linear correlations relating the undrained residual shear strength of loose, medium dense, and dense (D r?=?12%, 50%, and 90% before consolidation) sand–silt mixtures to the equivalent void ratio are obtained. The concept of the equivalent void ratio will then be used as a key parameter to express the dilatancy behavior of both clean and silty sand soils. Moreover, from the experimental results obtained, it is clear that the global void ratio cannot be used as a state parameter and may not represent the actual behavior of the soil as well.  相似文献   

6.
Silt is available in many parts of the world in combination with sands and clays. However, due to lack of clear understanding of its engineering behaviour, most of the time it is interpreted in terms of either sands or clays. Structures that are usually built on silty soils are designed to take into account design procedures developed for sandy or clayey soils. Presence of silts in combination with varying amount of sand and clays produces silt that is either plastic or non-plastic in nature. Silt is available in and around the Delhi region, in a majority mixture along with fine sands, which is non-plastic in nature. On the other hand silty deposits found in offshore Bombay High region are found in abundance along with significant amounts of clays and are termed as plastic silts. In this paper a comparison of the stress-strain behaviour of plastic and non-plastic silts is carried out under triaxial compression loading during both drained and undrained conditions. Two representative samples each from Delhi and Bombay High regions were considered for this comparison and results of stress-strain under four sets of confining pressure are discussed in detail. It is observed from this study that behaviour of silts is mainly dependent on the composition and structure of the resultant soil matrix. It is concluded from the results that shear strength parameters as well as volume change/pore pressure response of silty soils is dominated by the constituent soil present along with the silt. It is seen from the comparative behaviour of non-plastic and plastic silts that the presence of sand and clays has a governing effect on pore pressure development and the resultant friction angle. The study also corroborated that the nature of silt is transitional both in the case of plastic and non-plastic forms.  相似文献   

7.
饱和粉砂不稳定性的试验研究   总被引:3,自引:0,他引:3  
符新军  赵仲辉 《岩土力学》2008,29(2):381-385
通过对净砂和级配良好粉砂(含10 %粉土)进行一系列三轴固结不排水试验(CU),研究了粉土、孔隙比和围压对饱和粉砂不稳定性的影响。试验结果表明,净砂与粉砂在不排水剪切条件下均会出现应变软化现象(即不稳定性)。同一围压下脆性指数(IB)随孔隙比增加,但不稳定线的应力比随孔隙比增加而减小。引用等效粒间孔隙比(ege)后,净砂和粉砂在ege-ln p?平面上拥有基本相同的临界状态线。在临界状态理论及等效粒间孔隙比的基础上,提出在同一修正状态参数(?ge)下净砂和级配良好粉砂有相似的不稳定性。  相似文献   

8.
The evaluation of the undrained cyclic resistance of sandy deposits is required to forecast the soil behaviour during an earthquake (liquefaction, cyclic mobility); due to the difficulties in obtaining undisturbed samples of most liquefiable soils, it is usually deduced from field test results such as cone penetration tests. This paper proposes a methodology to evaluate the undrained cyclic resistance from normalised cone resistance of two well-studied silica sands (Ticino and Toyoura), with different mineralogy, one mainly composed of feldspar, the other of quartz. The determination of the cyclic resistance of Ticino and Toyoura sands was achieved through undrained cyclic triaxial tests on reconstituted specimens. The tip resistance was deduced from CPTs performed in centrifuge with a miniaturised piezocone on homogeneous reconstituted models. Both the undrained cyclic and tip resistances were correlated with the state parameter ψ. Results of centrifuge and triaxial tests were combined through ψ to deduce the cyclic resistance ratio CRR directly from the normalised cone resistance. The shape of the curve relating CRR to the normalised cone resistance resulted unusual respect to all the recognised curves widespread in the geotechnical literature. The aim of the proposed correlations is to provide a useful instrument to improve the actual knowledge on liquefaction and to give a contribution based on the critical state soil mechanics framework to the development of refined correlations between the cyclic resistance of a sand and the results of cone penetration tests.  相似文献   

9.
Adding a small amount of non-plastic silt to clean sands may lead to dramatic loss of shear strength and a noteworthy tendency toward contraction when the mechanical behavior of the mixture is compared with that of the clean host sand. Thus, simulation of the behavior of silty sands with varying fines content is still a challenging subject in geomechanics. A unified constitutive model for clean and silty sands is presented in this paper. To eliminate the factitious decrease of void ratio associated with inactive silt particles in various silty sand mixtures, the concept of equivalent void ratio is used in the model formulation instead of the global void ratio. In addition, the instantaneous soil state is expressed in terms of intergranular state parameter taking into account the combined influence of intergranular void ratio, mean principal effective stress and fines content. Then, dilatancy and plastic hardening modulus are directly linked to the intergranular state parameter. To improve the model capacity in simulation of cyclic tests, new features are added to the plastic hardening modulus. It is shown that the proposed model can reasonably reproduce the mechanical behavior as well as the onset of flow liquefaction instability of clean and silty sands using a unique set of parameters.  相似文献   

10.
上海粉土液化特性及孔压模型的试验研究   总被引:17,自引:0,他引:17  
根据循环三轴试验,分析了上海原状及重塑粉土的液化特性,提出了原状粉土的孔压上升模型,并与细砂的液化特性和孔模型进行了对比。  相似文献   

11.
南京砂强度特征与静态液化现象分析   总被引:2,自引:1,他引:1  
朱建群  孔令伟  钟方杰 《岩土力学》2008,29(6):1461-1465
在松散、中密和密实状态下,以南京粉细砂三轴固结不排水试验结果为基础,进行了强度、变形与静态液化特征的分析。松散南京砂强度特性表现出典型的应变软化,当轴向变形小于1 %时强度达到最大值,而后急剧降低;在50,100 kPa围压时发生了静态液化。但随着固结压力的增大,静态液化消失。与南京砂具有相同土骨架的松散纯净砂却在低围压下未出现静态液化,其形成机制是:粉粒的存在未使土体孔隙比发生较大变化,却引起更大的体缩性;中密和密实南京粉细砂表现出加工硬化的强度特征,临界应力状态线倾角高达55°,具有较高的抗静态液化能力。  相似文献   

12.
Liquefaction resistance of granular soils is commonly characterized by the cyclic resistance ratio (CRR) in the simplified shear stress procedure of liquefaction potential assessment. This parameter is commonly estimated by cyclic tests on reconstituted samples or empirical correlations between liquefied/non-liquefied case histories. The current study employs results of cyclic triaxial tests on reconstituted soil specimens and presents a predictive equation for cyclic resistance ratio (CRR) of clean and silty sands. The CRR equation is a function of relative density, effective mean confining pressure, non-plastic fines content, number of harmonic cycles for liquefaction onset, and some other basic soil properties. It is demonstrated that the developed relationship obtains reasonable accuracy in the prediction of laboratory-based CRR. Based on the developed CRR model, new relationships are then presented for the coefficient of effective overburden pressure (Kσ) and magnitude scaling factor (MSF), two important modification factors in the simplified shear stress procedure. These new modification factors are then compared with those recommended by previous researchers. Finally, the possible application of the proposed CRR model in field condition is shown for a specific case. This study provides a preliminary insight into the liquefaction resistance of silty sands prior to the complementary laboratory studies.  相似文献   

13.
Zusammenfassung Es wird ein kurzer Überblick über den komplexen Gesteinsbestand eines Gebietes im arabischen Grundgebirge des südlichen Hedjaz gegeben. Es zeigte sich, daß die tektonischen, stark überprägten und metamorphen Serien heute noch nicht in das Schema der in der Literatur genannten Serien eingebaut werden können. Diese scheinen sowohl hinsichtlich ihres stofflichen Bestandes wie auch des Zusammenhanges ihrer strukturellen und metamorphen Prägung noch zu wenig gekennzeichnet zu sein.Die im Grundgebirge weit verbreiteten Seitenverschiebungen werden kurz beschrieben und ihr Alter als wahrscheinlich spät-präkambrisch aufgefaßt.
The paper gives a general view of the different rock series occurring in a mapped area of the basement complex in the southern Hedjaz. The predominant masses of strongly tectonized and epimetamorphic series cannot be correlated with some series, which are named already in the literature of Arabia. These latter series seem defined not sufficiently in their composition and in the relation to their structural and metamorphic development.The wrench movements, wide spread in the Arabian basement, are briefly described and defined as being probably late-precambrian.

Résumé L'auteur donne un bref aperçu de la composition géologique complexe d'une région du soubassement arabe de l'Hedjaz du Sud. Il s'est avéré qu'à l'heure actuelle les séries fortement tectonisées et métamorphiques ne peuvent encore être intégrées au schéma des séries mentionnées par la littérature. Ces séries semblent être encore trop peu caractérisées en ce qui concerne leur composition ainsi que le rapport entre leurs caractéristiques structurelles et métamorphiques.Les failles horizontales de décrochement, qui sont très répandues dans le soubassement, sont décrites brièvement et définies comme datant probablement de la fin de l'antécambrien.

, . , , . , . , .
  相似文献   

14.
The magnetic anomalies over the Laach volcanics and in adjacent areas were interpreted by comparison with the fields of three-dimensional model bodies. In addition to an aeromagnetic survey, magnetic measurements were carried out on the ground and in the laboratory. Most of the model bodies in the Laach volcanic field require a thickness adjustment of only a few tens of meters to achieve a correlation of the magnetic model fields with the anomalies detected at ground level or at flight altitude.The three-dimensional model calculations did not yield any evidence for the existence of a deep-seated body which might be interpreted as a remnant magma chamber from which magma was explosively extruded during the eruption of the Laacher See volcano.The extensive positive magnetic anomaly near Ahrweiler is interpreted as being caused by a magnetized tabular body located at a depth of 8 km.The sharp bend of the isolines in the northeastern part of the Ahrweiler anomaly is a possible indication of the existence of magnetic rock at a maximum depth of 3–4 km. However, the rock need not necessarily occur in the form of a discrete body. The longitudinal axis of the model body lies on the line connecting the Siebengebirge with the Laach volcanic area.Two model body configurations have been developed for the magnetic anomaly near Kelberg. One of them consists of an upper part corresponding to the magma chamber of the Tertiary volcanics of the Hocheifel (high Eifel), and a lower part that can be regarded as a southern extension of the deep-seated body which is probably the source of the Ahrweiler anomaly. The other configuration represents a magnetized zone formed by thermal metamorphism due to an underlying plutonic body or by magma differentiation, possibly during the Paleozoic.
Zusammenfassung Die Magnetfeldanomalien im Raum der Laacher Vulkanite und deren Umgebung wurden durch Vergleich mit den Feldern von dreidimensionalen Modellkörpern interpretiert. Dazu wurden außer der aeromagnetischen Vermessung auch ergänzende Magnetfeldmessungen am Boden sowie gesteinsmagnetische Messungen herangezogen. Für die Mehrzahl der Modellkörper im Laacher Vulkanfeld reicht eine Mächtigkeit von einigen Zehnermetern aus, um die magnetischen Modellfelder den gemessenen Anomalien in Boden- und Flugniveau anzugleichen.Die dreidimensionalen Modellrechnungen haben keinen Hinweis auf die Existenz eines tiefreichenden Körpers ergeben, der als Restkörper einer Magmenkammer, die bei der Eruption des Laacher Sees z. T. ausgeblasen wurde, gedeutet werden könnte.Der weiträumigen magnetisch positiven Anomalie bei Ahrweiler wird eine magnetisierte Platte in ca. 8 km Tiefe zugeordnet.In der engräumigen Krümmung der Isolinien im NE-Teil der Ahrweiler-Anomalie deutet sich magnetisches Gestein in maximal 3–4 km Tiefe an, das aber nicht unbedingt als ein kompakter Körper vorliegen muß. Die Längsachse des betreffenden Modellkörpers liegt in der Verbindungslinie von Siebengebirge und Laacher Vulkangebiet.Fur die magnetische Anomalie bei Kelberg sind zwei Modellkörperkonfigurationen erarbeitet worden — die eine besteht aus einem oberen Modellkörper, welcher der Magmenkammer des tertiären Hocheifelvulkanismus entspricht und aus einem unteren Körper, der als Erweiterung nach Süden des für die Ahrweiler-Anomalie angenommenen tiefen Körpers betrachtet werden kann. Die andere Konfiguration stellt eine magnetisierte Zone dar, die durch thermischen Kontakt mit einem darunterliegenden plutonischen Körper oder auch durch Magmendifferenzierung, möglicherweise im Paläozoikum, entstanden ist.

Résumé Les anomalies magnétiques dans les volcanites du Laacher See et dans les régions avoisinantes ont été interprétées par comparaison avec les champs qu'engendreraient des corps-modèles tridimensionnels. Outre un levé aéromagnétique, des mesures complémentaires ont été effectuées sur le terrain et sur des échantillons de roches. Dans la région volcanique de Laach, la plupart des corps-modèles utilisés requièrent un ajustement en épaisseur qui ne dépasse pas quelques dizaines de mètres pour assurer la corrélation entre les champs magnétiques du modèle et les anomalies mesurées.Le calcul du modèle tridimensionnel n'a fourni aucune indication de l'existence d'un corps profond qui pourrait s'interpréter comme le reste d'une chambre magmatique, partiellement vidée par l'éruption du Laacher See.L'anomalie magnétique positive qui affecte une grande surface près d'Ahrweiler est interprétée comme due à un corps magnétique tabulaire situé à 8 km de profondeur.La courbure prononcée des isogrades dans la partie nord-est de l'anomalie d'Ahrweiler pourrait traduire la présence d'une roche magnétique à une profondeur maximale de 3 à 4 km. Cette roche ne doit cependant pas nécessairement se présenter sous la forme d'un corps individualisé. Le grand axe du corps magnétique modèle correspond à la ligne qui relie le Siebengebirge à la région de Laach.En ce qui concerne l'anomalie magnétique de Kelberg, deux configurations de corps-modèles ont été envisagées. La première consiste en un corps peu profond correspondant à la chambre magmatique du volcanisme tertiaire du Haut Eifel et en un corps plus profond qui pourrait être le prolongement vers le sud de celui qui serait responsable de l'anomalie d'Ahrweiler. L'autre configuration fait appel à une zone magnétique formée soit par le métamorphisme thermique engendré par une masse plutonique sousjacente, soit par une différenciation magmatique d'âge paléozoïque probable.

. , , . , , . , , , . Ahrweiler'a , 8 . Ahrweiler'a , 3–4 , . , . , Kelberg'a, : , , , , , Ahrweiler'a. , , , , , , .
  相似文献   

15.
Zusammenfassung Die einzelnen tektonischen Einheiten des Iran werden in ihrer faziellen und strukturellen Entwicklungsgeschichte dargestellt. Fazies und Paläogeographie sprechen dafür, daß vom Infrakambrium bis in die Trias der gesamte Raum zwischen dem Persischen Golf und dem Elburs-Gebirge eine einheitliche Entwicklung genommen hat. Eine zusammenhängende Plattformsedimentation in Schelffazies kennzeichnet dieses Gebiet während des gesamten Zeitraums. Es ist ein Teil Gondwanas. Paläomagnetische Befunde stützen diese Aussage. Ozeanische Kruste und damit Hinweise auf die Tethys als eine strukturelle Einheit fehlen während dieser Zeit in diesem Gebiet. Lediglich als Faunenprovinz in Flachmeerfazies ist sie wirksam. Das offene Meer lag vom Infrakambrium bis zur oberen Trias im Norden. In der Trias tritt mit einer Heraushebung, die mit tiefgreifender Lateritisierung verbunden ist, und einer anschließenden Transgression ein grundlegender Wechsel des geodynamischen Regimes ein. Von jetzt an erfolgen die Ingressionen in den Iran von Süden. Eine engräumige fazielle Differenzierung setzt ein. Kontinental beeinflußte Sedimente im Jura zeigen, daß im Iran ein Hochgebiet entstanden ist. Gleichzeitig tretenwahrscheinlich in Anlehnung an langlebige Geosuturen — Ophiolith-Radiolarit-Zonen auf, die als das Ergebnis intrakratonischer Zerbrechung gedeutet werden. Die Ingressionen gehen wahrscheinlich von Tiefseerinnen aus, in denen auch die Ophiolithe konzentriert sind. Der Aufstieg des ophiolithischen Materials an die Oberfläche erfolgte entlang von Linien, an denen sich flach geneigte Unterschiebungen von Kruste unter Kruste ereigneten. Dabei kam es zu erheblichen Krustenverkürzungen. Möglicherweise fällt der Umbruch des tektonischen Regimes in der Obertrias mit der Plattenkollision Arabia-Iran/ Eurasia zusammen. Die Grenze zwischen Arabia-Iran und Eurasia liegt aber nicht im Gebiet des Persischen Golfes und der Zagros-Ketten, sondern muß nördlich des Elburs-Gebirges gesucht werden.
The individual tectonic units of Iran are represented with respect to the history of the development of their facies and structure. Facies and paleogeography indicate that the entire area between the Persian Gulf and the Elburz Mountains had a uniform development until the Triassic. During the whole period a coherent platform sedimentation remained characteristic of this area, which is part of Gondwana. Paleomagnetic data support this statement. Oceanic crust and thus any indications of the Tethys as a structural unit are absent in this area for that period of time. Its existence is only demonstrated in faunal provinces in shallow-marine facies. From the Infra-Cambrian to the Late Triassic the northern part of the area was open sea. During the Triassic, uplifting processes combined with deep lateritization and subsequent transgression initiated a basic change in the geodynamic regime. From this time on the ingressions into Iran proceeded from the south. At this time differentiation of facies began within small areas. Continental influences in the Jurassic sediments show that an elevated area was formed in Iran. At the same time ophiolite-radiolarite zones occurred, probably along long-lived geosutures. These zones are interpreted to be the result of processes breaking up the craton. Probably, the ingressions started from deep-sea furrows where ophiolite concentrations are found. The ascension of the ophiolitic material to the surface occurred along lines where gently dipping subduction of crust under crust took place. During this process it came to considerable crustal shortening. It is possible that the change in the tectonic regime during the Late Triassic coincided with the collision of the Arabia-Iran and Eurasia plates. The boundary between the Arabia-Iran and Eurasia plates is, however, not to be found in the area of the Persian Gulf and the Zagros mountain ranges, but is assumed to be north of the Elburz Mountains.

Résumé Chacune des unités tectoniques de l'Iran font l'objet d'un exposé concernant leur développement du point de vue de leur facies et de leur structure. Le facies et la paléogéographie indiquent que, de l'Infracambrien au Trias, tout le territoire compris entre le Golf persique et la chaîne de l'Elbours a eu un développement unitaire. Une sedimentation de plateforme cohérente, à facies de shell, caractérise cette région pendant toute cette période. C'est une partie du Gondwana. Des données paléomagnétiques appuient cette affirmation. Toute croûte océanique et, de ce fait toute indice d'une Téthys en temps qu'unité structurale, sont absent dans cette région à ce moment. Une mer ouverte s'y étend au nord de l'Infracambrien jusqu'au Trias supérieur. Au Trias, un soulèvement, auquel est liée une forte latéritisation, et la trangression qui lui est liée, entraînent un changement radical du régime géodynamique. A partir de ce moment, des ingressions se produisent en Iran à partir du sud introduisant des différences de facies. Des sédiments montrant une influence continentale montrent qu'au Jurassique un fort soulèvement s'est produit en Iran. En même temps, vraisemblablement suivant une géosuture depuis longtemps active, apparurent des zones ophiolothiques à radiolarites, qui indiquent une rupture intracratonique. Les ingressions émanent vraisemblablement d'un sillon océanique profond dans lequel sont également concentrées les ophiolithes. La montée du matériau ophiolithique à la surface s'en suivit le long de lignes suivant lesquelles se sont produits dessous-charriages intracrustaux, d'où sont résultés de notables racourcissements de la crôute. Il est possible que cette rupture du régime tectonique coïncide, au Trias supérieur, avec la collision des plaques de l'Arabie Iran et de l'Ewrasie. La limite entre l'Arabie-Iran et l'Eurasie ne se trouve donc pas dans la région du Golfe persique et des chaînes du Zagros, mais doit être recherchée au nord de la Chaîne de l'Elbours.

P . , , . , . , , , , . . . , , . . . , . -, , , , , . , , , . , , , . . , - . , .
  相似文献   

16.
The paper analytically discusses certain palaeoecological criteria in the reconstruction of Lower Miocene (Aquitanian-Burdigalian) palaeobiogeography of the Indian subcontinent. The period is characterised by major marine transgressions and a prolific marine invertebrate and terrestrial vertebrate faunas. Faunal affinities of molluscs from western (Sind-Baluchistan) and eastern (Garo Hills) sectors are distinct and different. Molluscs of Garo Hills show affinity to Burmese species, whereas Sind-Baluchistan species shows similarity to that of the Mediterranean region. Marine molluscs resemble with the present-day taxa of the Arabian Sea and Bay of Bengal, where more than 35% species are common. This similarity is also evidenced by marine elasmobranchs, where approximately 33% species and 86% genera are similar to that of the Recent taxa. Terrestrial mammals show an intermingling of southern U.S.S.R. and African forms along with the presence of probably some groups belonging to the Indian subcontinent.Angiosperms are the dominant group. The Lower Miocene floras of the eastern and the western sectors are entirely different. The palm,Sabal major andPinus are reported from various localities. The climate in the western sector and South India was tropical, whereas in the eastern sector, it was variable.The Lower Miocene period is also marked by the contraction of Sindhu Sea, Bangla Sea and the Burmese Gulf southwards resulting in the final disappearance of the sea by the Pliocene.
Zusammenfassung Die Paläobiogeographie des unteren Miocän (Aquitan-Burdigal) läßt sich auf dem indischen Subkontinent aus den palökologischen Daten rekonstruieren. Zu dieser Zeit gab es viele marine Invertebraten und terrestrische Vertebraten-Faunen, die große marine Transgression anzeigen. Die Mollusken des Westens (Find-Baluchistan) und Ostens (Garo-Gebirge) sind unterschiedlich. Die Mollusken des Garo-Gebirges sind mit den Spezies von Burma verwandt. Dagegen sind die Faunen von Sind-Baluchistan für die mediterrane Faunenprovinz typisch. Die marinen Mollusken sind verwandt mit den Faunen des Arabischen Meeres und der Bucht von Bengalen; etwa 35% der Spezies sind gleich. Von den marinen Elasmobranchien sind ungefähr 33 % Spezies und 86% Genera gleich wie man sie in den rezenten Faunen findet. Terrestrische Sänger zeigen eine Mischung von südlicher U.S.S.R. und Afrika mit einigen Teilen des Indischen Subkontinentes.In den Pflanzen-Gruppen herrschen die Angiospermen vor. Die Untermiocän-Flora der östlichen und westlichen Gebiete ist ganz unterschiedlich. Der Palme, dieSabal Major undPinus sind aus verschiedenen Lokalitäten bekannt. Das Klima im Westen und im Süden Indiens war tropisch, im Osten dagegen war es wechselfeucht.Das Untermiocän-Meer im Gebiet Sind, Bangladesh und Burma verschwindet vor dem Pliozän.

Résumé Cet article analyse certains critères paléoécologiques dans la reconstitution de la paléogéographie du Miocène inférieur (Aquitanien-Burdigalien) de l'Inde subcontinentale. La période est caractérisée par de grandes transgressions marines et par des faunes abondantes d'invertébrés marins et de vertébrés terrestres. Les affinités fauniques des mollusques sont différentes dans les secteurs occidentaux (Sind-Baluchistan) et orientaux (Garo Hills). Les mollusques des Garo Hills montrent des affinités avec les espèces de Burma, tandis que les espèces de Sind-Béloutchistan montrent des similitudes avec celles de la région méditerranéenne. Les mollusques marins ont des ressemblances avec les taxons actuels de la Mer d'Arabie et du Golfe du Bengal, où plus de 35% des espèces sont les mÊmes. Cette similarité vaut aussi pour les élasmobranches marin, dont 33% des espèces et 86% des genres ressemblent aux taxons récents. Les mammifères terrestres montrent un mélange de formes du sud de l'U.S.S.R. et de formes africaines, allant de pair avec la présence de certains groupes probables appartenant au sous-continent indien.Les angiospermes forment le groupe dominant. Les formes du Miocène inférieur des secteurs orientaux et occidentaux sont entièrement différentes. Le palmier, le grand Sabal et le pin, sont connus dans différentes localités. Le climat dans le secteur occidental et dans l'Inde méridionale était tropical, tandis que dans le secteur oriental, il était variable.La période du Miocène inférieur est également marquée par le rétrécissement de la Mer de Sindhu, de la Mer de Bangla et du Golfe de Burma vers le sud, avec comme résultat la disparition finale de la mer au Pliocène.

(Aquitanian Nurdigalian) . . (Sind- Beluchistan) (Garo Hills) . , . : 35% . Elasmobranchs 33 % 86 % . , . . , Sabal major . , , , , , — . Sindhu, .
  相似文献   

17.
The data of the two long seismic profiles crossing Iceland (Nasp 1972 andRrisp 1977) have revealed its deeper structure and its relation to the Reykjanes and the Faeroe-Iceland Ridge. All deep velocity levels dip down from the ocean towards Iceland. The maximum velocity found on Iceland does not exceed 7.6–7.7 km/s. The 7.0 km/s velocity level is of complex shape. Due to a disagreement of first arrivals at the crosspoint of the two profiles crustal velocity anisotropy may exist.Two different models can be derived from the seismic cross sections. The first model contains a thin oceanic crust being 10–15 km thick. This layer is followed directly by the asthenosphere with velocities near 7.0–7.4 km/s. The top of this diapir-like asthenosphere should be in a partly molten stage. The other version, favoured by the authors, suggests a crust of 30 km thickness which is underlain by mantle material with velocities of 7.5–7.7 km/s. The top of the asthenosphere is assumed to exist in a depth of about 50 km. In the upper crust at 10–15 km depth there occurs a local zone of rocks being in a partly molten stage, as evidenced by the reduced shear wave velocity and the high electrical conductivity. Due to this configuration Iceland forms combined structure with the Faeroe-Iceland Ridge. Despite of its great thickness the crust of Iceland must be regarded as belonging to the oceanic type because of its basic rock composition, thus it is classified as suboceanic.
Zusammenfassung Die Daten der beiden seismischen Langprofile auf Island (Nasp 1972 undRrisp 1977) erlauben Aussagen über die tiefere Struktur Islands und deren Zusammenhang mit dem Reykjanes und dem Faeroe-Island-Rücken. Alle tieferen Geschwindigkeitshorizonte fallen vom Ozean her unter Island ein. Die größte unter Island beobachtete Geschwindigkeit beträgt 7.6–7.7 km/s. Einen komplizierten Verlauf zeigt die 7.0 km/s Geschwindigkeitslinie. Andererseits kann auch Anisotrophie nicht ausgeschlossen werden.Die berechneten seismischen Profile erlauben zwei Interpretationen für die Krustenstruktur Islands. Die erste Deutung geht von einer dünnen (10–15 km mächtigen) ozeanischen Kruste aus, die direkt von der domartig aufdringenden Asthenosphere unterlagert wird. Der oberste Bereich der Asthenosphäre ist partiell geschmolzen und zeigt Geschwindigkeiten von über 7.0–7.4 km/s. Die andere, von den Autoren vertretene Deutung, geht von einer etwa 30 km mächtigen Kruste aus, die auf Mantelmaterial mit Geschwindigkeiten von 7.5–7.7 km/s liegt. Die Asthenosphäre folgt erst in 50 km Tiefe. Innerhalb der Kruste ist in 10–15 km Tiefe eine begrenzte Zone mit partiell geschmolzenem Gestein eingelagert, die sich durch eine verringerte Geschwindigkeit der Scherwellen und eine hohe elektrische Leitfähigkeit zu erkennen gibt. Die Kruste Islands bildet mit der Faeroe-Island-Rückens eine Einheit. Ungeachtet der Krustendicke von 30 km gehört die Kruste Islands aufgrund der basischen Zusammensetzung zum ozeanischen Typ und nicht zum kontinentalen.

Résumé Les données sur les deux longs profils sismiques en Islande (Nasp 1972 etRrisp 1977) permettent de déterminer la structure profonde et la relation avec le Seuil de Reykanes et des ïles Färoe. Tous les horizons à vitesse faible viennent du côté de l'Océan sous l'Islande. La vitesse la plus élevée observée sous l'Islande est de 7.6 à 7.7 km/sec. La courbe des vitesses montre une allure compliquée. D'autre part l'anisotropie ne peut être exclue. Les profils sismiques permettent deux interprétations de la structure de la croûte sous l'Islande. La première est celle d'un croûte mince (10–15 km) océanique, placée directement au-dessus de l'asthénosphère qui y pénétre à la manière d'un arceau. La couche supérieure de l'asthénosphère est partiellement fondue et montre des vitesses de plus de 7.0–7.4 km/sec. L'autre interprétation, d'après les auteurs, part d'une croûte de presque 30 km. au-dessus d'une espèce de manteau où la vitesse irait de 7.5 à 7.7 km/sec. L'asthénosphère se trouverait à 50 km. de profondeur. A l'intérieur de la croûte, à une profondeur de 10–15 km. se trouverait une zone restreinte, partiellement fondue, que revèle une vitesse réduite des ondes de cisaillement et sa haute conductibilité. La croûte d'Islands et celle du Seuil des Iles Färoe ne forment qu'une seule unité. Malgré la valeur de 30 km. la croûte d'Islande appartient au type oc"anique, et non pas au type continental à cause de sa constitution basique.

(—1972 —1977) - . , 7,7 /. . . 10–15 , 7,0–7,4 /. . , , 30 7,5–7,7 /. 50 . 12–18 , . , .
  相似文献   

18.
Zusammenfassung Tektonische Lage und Sedimentationsgeschichte fassen Südalpin-Ostalpininterne (subtatrische und südlichere) Karpaten und Dinariden zu einer Einheit zusammen, die einen Teil des südlichen Kontinentalrandkomplexes der Tethys gebildet hatte. Zur Rekonstruktion dieses Kontinentalrandes ist eine palinspastische, die alpinen Deformationen entzerrende Rekonstruktion nötig. Versuche in dieser Richtung zwingen zu einer neuen Analyse des Alpen-Dinariden-Problems. Ausgehend von den gro\en prÄoligozÄnen Schubweiten in den nordvergenten Alpen und Karpaten einerseits, den südvergenten Helleniden und damit wahrscheinlich auch den Dinariden andererseits gelangt man zum Schlu\, da\ aus dem heutigen tektonischen übereinander ein palÄogeographisches Nebeneinander nur durch Annahme von mindestens zwei aufeinander folgenden Bewegungsphasen von ganz verschiedener Tendenz zu bewerkstelligen ist. Vor dem UnteroligozÄn entstand der Hauptteil des nordvergenten alpinen sowie des südvergenten dinarisch-hellenischen DeckengebÄudes. Der Vergenzwechsel zwischen dem Ostende der slowakischen Karpaten bei Koice und dem Westende der innerdinarischen Einheiten bei Zagreb verlangt eine dextrale Senke-Senke-Verschiebungszone, die heute zerrissen ist. Um den Zusammenhang wiederherzustellen und gleichzeitig palinspastischen Raum zu schaffen für die Dinariden, wird eine jungtertiÄre dextrale Verschiebung von im Osten 300 km lÄngs der insubrischen Linie s. l. postuliert, deren Implikationen besonders auch in den Westalpen und an der Karpaten-Balkan-Grenze spürbar sein müssen.
Southern Alps, Austroalpine nappes, the internal (Subtatrid etc.) units of the Carpathians and the Dinarids, on the evidence of paleogeographic development and present tectonic relations, once belonged to neighboring parts of the southern continental margin of the Mesozoic Tethys sea. Reconstruction of this margin requires palinspastic inversion of Alpine deformations. A new look at the problems involved reveals the necessity of at least two phases of vastly differing kinematics. Before the Oligocene, ± N-S compression of several hundred kilometers built up the nappe edifices of the Alps and the internal Carpathians (with northerly vergence) as well as that of the Dinarids-Hellenids (with southerly vergence). Between the eastern end of the first system in eastern Slovakia and the western end of the second near Zagreb, there must have been a zone of dextral sink-sink strike slippage which is now disrupted. In order to account for this disruption and, at the same time, to find an empty space to palinspastically accommodate the Dinarids, an Oligocene-Neogene dextral strike-slip motion of 300 km along the Insubric fault zone is required, with considerable consequences for the western Alps as well as for the Balkan-Carpathian boundary

Résumé Avant l'orogénèse alpine les Alpes méridionales, les nappes austroalpines, les Carpates occidentales internes et les Dinarides faisaient ensemble partie de la marge continentale méridionale de la Tethys mésozoÏque. Cela ressort aussi bien du développement paléogéographique que des relations tectoniques actuelles. La reconstruction de cette marge, demandant l'inversion palinspastique des déformations alpines, révèle l'activité d'au moins deux phases de cinématique notablement différente. Avant l'Oligocène, une compression nord-sud de plusieurs centaines de kilomètres au minimum aboutit à former la masse principale des nappes alpines et carpatiques internes, déversées vers le nord, et celle des Dinarides et Hellénides, déversées vers le sud. Entre la limite est en Slovaquie orientale, des premières, et la limite ouest, dans la région de Zagreb, des secondes, il devait exister une zone de failles à déplacement horizontal dextral, permettant de restituer la liaison cinématique des deux systèmes. Cette zone a été rompue ultérieurement ce qui implique l'existence d'un déplacement postérieur à l'oligocène inférieur avec un rejet horizontal dextral de 300 km de long de la faille insubrienne Ce déplacement s'impose si l'on veut remettre en place les nappes dinariques dans leur cadre paléogéographique mésozoÏque. D'importantes conséquences en résultent pour le système Balkano-Carpathique de mÊme que pour l'arc des Alpes occidentales.

, , , , . . . , , , , , , . - . , , . , , 300 , - .
  相似文献   

19.
The orthogneisses of the Spessart crystalline complex are derived from a granitic to granodioritic magma of S-type character which must have formed by anatexis of continental crust. It intruded into a relatively shallow crustal level, 410–420 Ma ago, at the Silurian. Trace element characteristics are consistent with a post-collision geotectonic environment testifying to extensional tectonics at the end of the Caledonian era.
Zusammenfassung Die Orthogneise des Spessartkristallins lassen sich von einem granitischen bis granodioritischen Magma von S-Typ-Charakter ableiten, das durch Anatexis kontinentaler Kruste entstanden sein mu\ und in ein relativ oberflächennahes Krustenniveau intrudierte. Die Platznahme erfolgte vor 410–420 Ma, d. h. im Silur. Die Spurenelement-Muster der Orthogneise entsprechen denen von Post-Kollisions-Granitoiden, was als Hinweis auf eine Phase der Dehnungstektonik am Ende der kaledonischen ära bewertet werden kann.

Résumé Les orthogneiss du Spessart sont dérivés d'un magma granitique à granodioritique de type S qui doit s'Être formé par anatexie de la croûte continentale. Ce magma a été intrudé dans un niveau peu profond de la croûte il y a 410–420 Ma c'est-à-dire au Silurien. La distribution des éléments en traces est en accord avec celle des granitoÏdes formés dans un contexte géodynamique de post-collision. Cette observation est en faveur d'une phase d'extension tectonique à la fin du cycle calédonien.

, — Wojcieszów-Kalke. , — . . , , , , .
  相似文献   

20.
The Dalma volcanic belt of the Singhbhum Precambrian terrain in eastern India is developed along the median zone of a linear basin flanked by Archaean cratonic basement to the south. The lavas, in a low grade metamorphic environment, preserve a strong compositional bimodality, with highly magnesian picritic volcanics developed at the base and low-K basalt flows above, constituting the bulk of the lava pile. The ultrabasic lavas have low concentrations of immobile incompatible elements, ratios of which are probably controlled by the source character. Dalma mafic flows are closely comparable in geochemical character to modern day mid-oceanic ridge basalts (MORB) with a dominance of light-REE-depleted basalts and ferrobasalts. However, in terms of certain element ratios (Th/Ta), deviation from MORB characteristics toward island arc tholeiites is apparent. In this respect the Dalma basalts appear to have a modified MORB composition and the closest chemical analogy may be basalts from back-arc basins, i. e. a supra-subduction zone environment. The bimodality of ultrabasic and mafic lavas is reminiscent of Archaean komatiitic provinces. The geochemical signature of the Dalma lavas, and the geological framework of the terrain, strongly point to a marginal basin domain developed in this crustal segment during the Proterozoic.
Zusammenfassung Der Vulkangürtel von Dalma liegt in der präkambrischen Region Singhbhum in Ostindien. Aufgeschlossen ist der Dalma-Gürtel im mittleren Bereich eines geradlinigen Bekkens, das im Süden durch Basement des Archaikums begrenzt wird. Die Laven befinden sich in einer geringmetamorphen Umgebung und weisen eine bimodale Zusammensetzung auf. An der Basis sind Magnesium-reiche und darüber Kalium-arme Basalte entwickelt, die repräsentativ für den Durchschnitt der Laven sind. Die ultrabasischen Laven enthalten niedrige Konzentrationen an immobilen nicht kompatiblen Elementen, deren Verhältnis wahrscheinlich von den Eigenschaften der Lavaquelle gesteuert wird. Der geochemische Charakter der mafischen Dalma-Vulkanite entspricht weitgehend den heutigen Basalten der ozeanischen Rücken (MORB). Dabei dominieren leicht abgereicherte REE-Basalte sowie eisenreiche Basalte. Vergleicht man allerdings Elementverhältnisse wie das von Th/Ta, wird eine Abweichung von dem typischen MORB-Charakter hin zu Inselbögen-Tholeiten deutlich. Berücksichtigt man diese Beobachtungen, scheinen die Dalma-Basalte eine modifizierte MORB-Zusammensetzung zu haben, die in ihrem Chemismus am ehesten den Basalten von Back-Arc-Becken, z. B. in einem Gebiet einer Supra-Subduktionszone, zu entsprechen. Die Bimodalität der ultrabasischen und mafischen Laven erinnert an archaische komatiitische Regionen. Die geochemische Zusammensetzung der Dalma-Laven sowie der geologische Rahmen des Gebietes deuten auf ein randliches Becken hin, das sich während des Proterozoikums entwickelt haben könnte.

Résumé La ceinture volcanique de Dalma, dans le Précambrien de Singhbhum (Inde Orientale) est située dans la partie médiane d'un bassin linéaire bordé au Sud par un socle cratonique archéen. Les laves se trouvent dans un environnement de faible degré de métamorphisme et présentent une composition nettement bimodale: volcanites picritiques très magnésiennes à la base, surmontées de coulées basaltiques pauvres en K, qui constituent l'essentiel de l'ensemble. Les laves ultrabasiques montrent de faibles concentrations en éléments immobiles incompatibles dont les rapports sont probablement déterminés par le caractère de la source. Les coulées basiques de Dalma sont très comparables, dans leurs propriétés géochimiques, aux basaltes récents des rides océaniques (MORB), avec une dominante de basaltes pauvres en terres rares légères et de ferro-basaltes. Toutefois, les rapport de certains éléments (Th/Ta) font apparaître, par rapport au MORB, une déviation vers les tholéiites d'arcs insulaires. A ce point de vue, les basaltes de Dalma montrent une composition de MORB modifée et une analogie avec les basaltes de bassins d'arrière-arc, c'est-à-dire en situation de supra-subduction. La bimodalité laves ultrabasiques/laves basiques est une réminiscence des provinces komatiitiques archéennes. Le signalement géochimiques des laves de Dalma et leur situation géologique plaident en faveur d'un domaine de bassin marginal développé dans ce segment central au cours du Protérozoïque.

, . , , . , , . , , . , . : MORB. , . , , .: /, MORB . , , , MORB, , .: . . , , .
  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号